Engineering Physics Commons^™

Logistic Curves, Extraction Costs And Peak Oil, Robert J. Brecha

Physics Faculty Publications

Debates about the possibility of a near-term maximum in world oil production have become increasingly prominent over the past decade, with the focus often being on the quantification of geologically available and technologically recoverable amounts of oil in the ground. Economically, the important parameter is not a physical limit to resources in the ground, but whether market price signals and costs of extraction will indicate the efficiency of extracting conventional or nonconventional resources as opposed to making substitutions over time for other fuels and technologies. We present a hybrid approach to the peak-oil question with two models in which the …

High Frequency Study Of Magnetic Nanostructures, Abhishek Srivastava

LSU New Orleans Theses and Dissertations

The work in this thesis is divided in three parts. In part one we developed electrodeposition method of Nickel Nanowire in commercial AAO template in constant current (Galvanostatic) mode, further we tried to estimate the growth rate from theory, from saturation magnetization and direct measurement from SEM image.

In part two we focused on using the Vector Network Analyzer (VNA) to measure the Ferromagnetic Resonance (FMR))of various magnetic Nanowire arrays. We employed different measurement geometries using microstripline and coplanar waveguide as microwave transmission lines.

In part three our aim was to study the magnetic properties of complex ferromagnetic system, especially …

Analyzing Wind Turbine Controller Effects On Structure Stress, Leo Groner, Susan Frost

STAR Program Research Presentations

Wind turbines generate electric power from clean renewable sources. They must be robust and reliable. Utility-scale turbines are designed to produce power within a set of wind speed parameters. When winds change, wind turbine blade pitch is used to protect the turbine from over speed damage.

Advanced control algorithms can increase power by extending the performance envelope or they can extend lifetime by reducing stress. A FAST simulation written in MATLAB / Simulink is used to simulate the dynamics of the integrated aerodynamic, mechanical and control subsystems of the turbine. Resonance modes may lead to large amplitude displacements and damage. …

Electronics Development For The Cherenkov Telescope Array, Margaret C. Murphy, Justin Vandenbrouke

STAR Program Research Presentations

Gamma-ray astronomy promises to elucidate the highest-energy particle accelerators in the Universe, and could play a key role in identifying the nature of dark matter. The Cherenkov Telescope Array (CTA), currently in the research and development stage, will study and capture gamma-rays with an order of magnitude grater sensitivity than the instruments already in place. Each telescope in the array will be equipped with dozens of camera modules each containing four TeV Array Readout with GSa/s sampling and Event Trigger (TARGET) chips. TARGET 4 has many internal settings, several of which were tested and analyzed to achieve an optimal operating …

Solar Light Bulb, David G. Guzman, Virgilio Gonzalez

COURI Symposium Abstracts, Summer 2012

The Solar Lighting project is a work driven towards building a low-cost and environmental-friendly solar bulb and to understanding the science behind its behavior. A solar light bulb refers to a device capable of absorbing and transferring solar energy to light up an enclosed area. By using the physical properties of fluids and light is possible to manipulate solar light waves to illuminate an enclosed structure. Moreover, this project attempts to utilize recycled materials that reduce the cost of such device, helping not only the planet but also the costumer’s pocket. The ultimate goal for this project is to scientifically …

Study Of Jet Transverse Momentum And Jet Rapidity Dependence Of Dijet Azimuthal Decorrelations With The Dø Detector, Kiran Chakravarthula

Doctoral Dissertations

In a collision experiment involving highly energetic particles such as hadrons, processes at high momentum transfers can provide information useful for many studies involving Quantum Chromodynamics (QCD). One way of analyzing these interactions is through angular distributions. In hadron-hadron collisions, the angular distribution between the two leading jets with the largest transverse momentum (pT) is affected by the production of additional jets. While soft radiation causes small differences in the azimuthal angular distribution of the two leading jets produced in a collision event, additional hard jets produced in the event have more pronounced influence on the distribution of …

Propagation Of Ultrasound Through Freshly Excised Human Calvarium, Armando Garcia Noguera

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The propagation of ultrasound through complex biological media, such as the human calvarium, poses a great challenge for modern medicine. Several ultrasonic techniques commonly used for treatment and diagnosis in most of the human body are still difficult to apply to the human brain, in part, because of the properties of the skull. Moreover, an understanding of the biomechanics of transcranial ultrasound may provide needed insight into the problem of blast wave induced traumatic brain injury (TBI). In the present study, the spatial variability of ultrasonic properties was evaluated for relevant frequencies of 0.5, 1, and 2.25 MHz. A total …

The Double Pendulum: Construction And Exploration, Benjamin J. Knudson

Physics

The exploration of a nonlinear mechanical system, the Double Pendulum, a physical pendulum on the end of a physical pendulum, using analytic and experimental approaches. Also included discussion of the design and construction of the Double Pendulum apparatus to work with Vernier LabPro and LoggerPro. The apparatus outputs live data of the angles to a LoggerPro which collects and produces time evolution graphs as well as a corresponding animation lending itself to comparison with theoretical models. Normal mode frequencies are found both analytically and experimentally for the the general (real) double pendulum. Examples of both simple (periodic) and complex (chaotic) …

Dynamics Of Non-Thermal Plasma Jets Under Variable Pressure, Mehmet Arda Akman

Electrical & Computer Engineering Theses & Dissertations

Non-thermal plasma (NTP) jets driven by short DC pulses have attracted the attention of researchers within the past decade due to their promising bio-medical applications in the fields of wound healing, cancer treatment and sterilization. The ability to operate at atmospheric pressure, room temperature and simple device configuration has greatly contributed to their appeal and adoption in the plasma science community. However, the mechanisms that sustain the plasma generation and propagation in ambient air are currently a topic of debate. For instance, what appears as a continuous stream of a plasma plume extending outwards from a plasma device into the …

Development Of A Pyrotechnic Shock Simulation Apparatus For Spacecraft Applications, Joseph Binder, Matthew Mccarty, Chris Rasmussen

Aerospace Engineering

This report details the research, design, construction, and testing of a pyrotechnic shock simulation apparatus for spacecraft applications. The apparatus was developed to be used in the Space Environments Lab at California Polytechnic State University. It will be used for testing spacecraft components with dimensions up to 24”x12”x12” as well as CubeSats. Additionally, it may be used as an instructional or demonstrational tool in the Aerospace Department’s space environments course. The apparatus functions by way of mechanical impact of an approximately 20 lb stainless steel swinging hammer. Tests were performed to verify the simulator’s functionality. Suggestions for improvement and further …

Inductive Metal Identification, Paul Maggi

Electrical Engineering

This project focuses on creating a device to differentiate between various types of metals via magnetic induction. Magnetic induction is used because it is both non-optical and non-contact. It achieves this by generating a varying magnetic field, which induces eddy currents in the metal. These eddy currents produce small disturbances in the surrounding magnetic field, which can be sensed with Hall Effect Sensors (HES). The primary challenge in this project was generating a sufficiently strong magnetic field to detectable disturbances. In order to achieve better results, a stronger magnetic field must be used as well as more sensitive Hall Effect …

Analysis Of Focal-Plane Measurements For Veritas Telescopes, William Hemmo Schuur

Physics

In this experiment we measured the Point Spread Function (PSF) of the telescope at different image locations using a python GUI and servo motors to automate a screen along the focal axis of the telescope. Our results show that the telescope T4 has a well-defined image distance at each elevation, but this distance shifts as the telescope is lowered. Additionally, off-axis telescope orientations are degraded by aberrations and at low elevation possibly some structural warping of the mirror. The VERITAS Telescopes are located in Southern Arizona at the Fred Lawrence Whipple Observatory.

Agent-Based Modeling Of Emergency Building Evacuation, Vi Q. Ha

Master's Theses

Panic during emergency building evacuation can cause crowd stampede, resulting in serious injuries and casualties. Agent-based methods have been successfully employed to investigate the collective human behavior during emergency evacuation in cases where the configurational space is extremely simple - usually one rectangular room - but not in evacuations of multi-room or multi-floor buildings. This implies that the effect of the complexity of building architecture on the collective behavior of the agents during evacuation has not been fully investigated. Here, we employ a system of self-moving particles whose motion is governed by the social-force model to investigate the effect of …

Magnetic Ordering And Structural Phase Transition In Strained Ultrathin Srruo3/Srtio3 Superlattice, Mingquiang Gu, Xiaoshan Wu, Guoping Zhang

Symposium 2012

No abstract provided.

Breaking Glass: Exploring The Relationship Between Kinetic Energy And Radial Fracturing In Plate Glass, Andrea Hulman

Scripps Senior Theses

When glass breaks from the impact of an object, it exhibits a distinctive shattering pattern comprised of two different regions. This pattern was investigated using experimental impacts and predicted using Young’s Modulus. Results were not as expected, and it is likely that there exists error in some measurements. Further investigation of this topic is recommended.

Low-Loss Meta-Atom For Improved Resonance Response, Derrick Langley, Ronald Coutu Jr., Peter J. Collins

Faculty Publications

Measurements of a meta-atom integrated with a low noise amplifier into the split-ring resonator are presented. A comparison is made between baseline meta-atoms and one integrated with a GaAs low noise amplifier. S-parameter measurements in a RF strip-line show the resonant frequency location. The resonance null is more prominent for the integrated meta-atom. Biasing the low noise amplifier from 0 to 7 VDC showed that the resonant null improved with biasing voltage. As the biasing voltage increases, the transmission null reduced from -11.82 to -23.21 dB for biases from 0 to 7 VDC at resonant frequency.

Cesium Absorption Spectrum Perturbed By Argon: Observation Of Non-Lorentzian Far Wings, Gordon E. Lott

Theses and Dissertations

The purpose of this research was to observe the core and far wing absorption spectra of the D₁ and D₂ lines of cesium (Cs) perturbed by argon (Ar). A 1.33 m scanning monochromator with a PMT detector was used to measure the spectra from 8300 Å to 9100 Å. A heat pipe was used to control the Cs concentration and Ar pressure allowing for a broad range of spectra to be collected. Spectra were collected for heat pipe temperatures of 50, 75, 100, 125, 150 and 175 °C, corresponding to Cs concentrations of approximately 6×10¹¹, 4×10 …

Advances In Ultrafast Time Resolved Fluorescence Physics For Cancer Detection In Optical Biopsy, R. R. Alfano

Publications and Research

We discuss the use of time resolved fluorescence spectroscopy to extract fundamental kinetic information on molecular species in tissues. The temporal profiles reveal the lifetime and amplitudes associated with key active molecules distinguishing the local spectral environment of tissues. The femtosecond laser pulses at 310 nm excite the tissue. The emission profile at 340 nm from tryptophan is non-exponential due to the micro-environment. The slow and fast amplitudes and lifetimes of emission profiles reveal that cancer and normal states can be distinguished. Time resolved optical methods offer a new cancer diagnostic modality for the medical community.

Qpced2.0: A Computer Program For The Processing And Quantification Of Polycrystalline Electron Diffraction Patterns, Xingzhong Li

Nebraska Center for Materials and Nanoscience: Faculty Publications

The processing and quantification of electron diffraction patterns have become vital in advanced electron crystallographic analysis work. A computer program, QPCED2.0, has been developed for the handling of selected-area electron diffraction patterns for polycrystalline materials. QPCED2.0 can be used to enhance the visibility of electron diffraction patterns, to convert electron diffraction patterns into intensity profiles, and to retrieve precisely the lattice d spacings and the integral intensities of the diffraction rings. The design and implementation of QPCED2.0 are elucidated and application examples are given.

Crystal Field Splitting And Optical Bandgap Of Hexagonal Lufeo3 Films, Wenbin Wang, Hongwei Wang, Xiaoying Xu, Leyi Zhu, Lixin He, Elizabeth Wills, Xuemei Cheng, David J. Keavney, Jian Shen, Xifan Wu, Xiaoshan Xu

Xiaoshan Xu Papers

Hexagonal LuFeO₃ films have been studied using x-ray absorption and optical spectroscopy. The crystal splitting of Fe³⁺ is extracted as E_e' - E_e" = 0.7 eV and E_a'1 - E_e' = 0.9 eV, and a 2.0 eV optical bandgap is determined assuming a direct gap. First-principles calculations confirm the experiments that the relative energies of crystal field splitting states do follow E_a'1 > E_e' > E_e" with slightly underestimated values and a bandgap of 1.35 eV.

Where Is The Best Place To Sit On A Roller Coaster? Forces, Physics, And Fun At Disneyland, Kelsey Lubetich

Scripps Senior Theses

The work presented in this thesis was undertaken to quantitatively determine the best place to sit on a roller coaster. Maximizing the time spent feeling weightless and the highest value of negative Z acceleration were used as criteria for the best seat. Acceleration values were measured on the California Screamin' roller coaster at Disney California Adventure Park using an iPhone and an application to record data from its accelerometers. After analyzing acceleration data, it was determined that the front row had the greatest negative acceleration in the z direction and was therefore the "best place" to sit.

Thermal Quench Effects On Ferroelectric Domain Walls, P. Paruch, A. B. Kolton, X. Hong, C. H. Ahn, T. Giamarchi

Xia Hong Publications

Using piezoresponse force microscopy on epitaxial ferroelectric thin films, we have measured the evolution of domain wall roughening as a result of heat-quench cycles up to 735 ◦C, with the effective roughness exponent ζ changing from 0.25 to 0.5. We discuss two possible mechanisms for the observed ζ increase: a quench from a thermal one-dimensional configuration and from a locally equilibrated pinned configuration with a crossover from a two- to one-dimensional regime. We find that the postquench spatial structure of the metastable states, qualitatively consistent with the existence of a growing dynamical length scale whose ultraslow evolution is primarily controlled …

Contamination Effects On Fixed-Bias Langmuir Probes, C.T. Steigies, A. Barjatya

Publications

Langmuir probes are standard instruments for plasma density measurements on many sounding rockets. These probes can be operated in swept-bias as well as in fixed-bias modes. In swept-bias Langmuir probes, contamination effects are frequently visible as a hysteresis between consecutive up and down voltage ramps. This hysteresis, if not corrected, leads to poorly determined plasma densities and temperatures. With a properly chosen sweep function, the contamination parameters can be determined from the measurements and correct plasma parameters can then be determined. In this paper, we study the contamination effects on fixed-bias Langmuir probes, where no hysteresis type effect is seen …

Electric-Field-Induced Interfacial Instabilities Of A Soft Elastic Membrane Confined Between Viscous Layers, Mohar Dey, Dipankar Bandyopadhyay, Ashutosh Sharma, Shizhi Qian, Sang Woo Joo

Mechanical & Aerospace Engineering Faculty Publications

We explore the electric-field-induced interfacial instabilities of a trilayer composed of a thin elastic film confined between two viscous layers. A linear stability analysis (LSA) is performed to uncover the growth rate and length scale of the different unstable modes. Application of a normal external electric field on such a configuration can deform the two coupled elastic-viscous interfaces either by an in-phase bending or an antiphase squeezing mode. The bending mode has a long-wave nature, and is present even at a vanishingly small destabilizing field. In contrast, the squeezing mode has finite wave-number characteristics and originates only beyond a threshold …

Growth Diagram And Magnetic Properties Of Hexagonal Lufe2o4 Thin Films, Wenbin Wang, Zheng Gai, Miaofang Chi, Jason D. Fowlkes, Jieyu Yi, Leyi Zhu, Xuemei Cheng, David J. Keavney, Paul C. Snijders, Thomas Z. Ward, Jian Shen, Xiaoshan Xu

Xiaoshan Xu Papers

Agrowth diagram of Lu-Fe-O compounds on MgO (111) substrates using pulsed laser deposition is constructed based on extensive growth experiments. The LuFe₂O₄ phase can only be grown in a small range of temperature and O₂ pressure conditions. An understanding of the growth mechanism of Lu-Fe-O compound films is offered in terms of the thermochemistry at the surface. Superparamagnetism is observed in the LuFe₂O₄ film and is explained in terms of the effect of the impurity hexagonal LuFeO₃ (h-LuFeO₃) phase and structural defects.

Ferroelectric Control Of Magnetocrystalline Anisotropy At Cobalt/Poly(Vinylidene Fluoride) Interfaces, Pavel Lukashev, Tula R. Paudel, Juan M. López-Encarnación, Shireen Adenwalla, Evgeny Y. Tsymbal, Julian P. Velev

Shireen Adenwalla Papers

Electric field control of magnetization is one of the promising avenues for achieving high-density energy-efficient magnetic data storage. Ferroelectric materials can be especially useful for that purpose as a source of very large switchable electric fields when interfaced with a ferromagnet. Organic ferroelectrics, such as poly(vinylidene fluoride) (PVDF), have an additional advantage of being weakly bonded to the ferromagnet, thus minimizing undesirable effects such as interface chemical modification and/or strain coupling. In this work we use first-principles density functional calculations of Co/PVDF heterostructures to demonstrate the effect of ferroelectric polarization of PVDF on the interface magnetocrystalline anisotropy that controls the …

Development Of Superconducting 500 Mhz Multi-Spoke Cavity For Electron Linacs, Dmitry Gorelov, Charles H. Boulware, Terry Grimm, Jean R. Delayen, C. S. Hopper, R. G. Olgave, Subashini U. De Silva

Physics Faculty Publications

Multi-spoke cavities are well-known options for acceleration of heavy and light ions. A recently developed multi-spoke cavity for β=1 presents an attractive opportunity to use this cavity type for electron accelerators. One of the main attractive features of this cavity type is its compactness for relatively low frequency. A simplified design at 500 MHz allowed building of a multi-spoke cavity and cryomodule in a 2-year time frame with confidence and development of effective manufacturing techniques. It also constitutes an important step in proving the usefulness of this kind of cavity design for new applications in the electron machines. Niowave is …

Characteristics And Fabrication Of A 499 Mhz Superconducting Deflecting Cavity For The Jefferson Lab 12 Gev Upgrade, Hyekyoung Park, Subashini U. De Silva, Jean R. Delayen

Physics Faculty Publications

A 499 MHz parallel bar superconducting deflecting cavity has been designed and optimized [1,2] for a possible implementation at the Jefferson Lab. Previously the mechanical analysis [3], mainly stress, was performed. Since then pressure sensitivity was studied further and the cavity parts were fabricated. The prototype cavity is not completed due to the renovation at Jefferson Lab which resulted in the temporary shutdown of the electron beam welding facility. This paper will present the analysis results and facts encountered during fabrication. The unique geometry of the cavity and its required mechanical strength present interesting manufacturing challenges.

Rf Modeling Using Parallel Codes Ace3p For The 400-Mhz Parallel-Bar/Ridged-Waveguide Compact Crab Cavity For The Lhc Hilumi Upgrade, Zenghai Li, Lixin Ge, Jean R. Delayen, Subashini U. De Silva

Physics Faculty Publications

Schemes utilizing crab cavities to achieve head-on beam-beam collisions were proposed for the LHC HiLumi upgrade. These crabbing schemes require that the crab cavities be compact in order to fit into the tight spacing available in the existing LHC beamlines at the location where the crab cavities will be installed. Under the support of US LARP program, Old Dominion University and SLAC have joint efforts to develop a 400-MHz compact superconducting crab cavity to meet the HiLumi upgrade requirements. In this paper, we will present the RF modeling and analysis of a parallel-bar/ridged-waveguide shaped 400-MHz compact cavity design that can …

High Power Test Of Rf Separator For 12 Gev Upgrade Of Cebaf At Jefferson Lab, S. Ahmed, M. Wissmann, J. Mammosser, M. Spata, C. Hovater, Geoffrey A. Krafft, Jean R. Delayen

Physics Faculty Publications

CEBAF at JLab is in the process of an energy upgrade from 6 GeV to 12 GeV. The existing setup of the RF separator cavities in the 5th pass will not be adequate enough to extract the highest energy (11 GeV) beam to any two existing halls (A, B or C) while simultaneously delivering to the new hall D in the case of the proposed 12 GeV upgrade of the machine. To restore this capability, several options including the extension of existing normal conducting (NC) and a potential 499 MHz TEM-type superconducting (SC) cavity design have been investigated using computer …