Mechanical Engineering Commons^™

Influences Of Material Extrusion Additive Manufacturing (Meam) Parameters And Additives On Polyvinylidene Fluoride (Pvdf) Properties., Niknam Momenzadeh

Electronic Theses and Dissertations

Beyond the beneficial characteristics of smart polymers associated with all polymers such as flexibility and cost fabrication, smart materials exhibit multifunctional behaviors. The prospect of integrating structural and sensing/actuation capabilities into a single structure gives design engineers an ability to innovate highly novel, multi-functional creations. Polyvinylidene Fluoride (PVDF) is one of the widely used multi-functional materials which offers a variety of desirable material properties. It possesses exceptional chemical and UV resistance, biocompatibility, low processing temperature and affordable price making it a competitive choice for many commercial applications. In addition, among polymers, PVDF is simply the most dominant piezoelectric polymer. On …

Utilization Of Recycled Filament For 3d Printing For Consumer Goods, Alexa Peterson

Apparel Merchandising and Product Development Undergraduate Honors Theses

The 3D printing market has been used in a wide variety of manufacturing industries including textile and apparel. Many consumers can now own a personal 3D printer at home for recreational printing. There are even websites dedicated to 3D printing patterns made by consumers. However, the materials used in the 3D printing process pose a problem for the environment due to their plastic-based nature. 3D printing is a layered process with each layer being printed depending on the layer below it for strength and stability. During the 3D printing process, great amounts of waste are produced as a result of …

Design Optimization Of An Elastically Supported Multi-Beam Rotordynamic System To Minimize Flexural Response With Considerations For Robustness, Bret R. Hauser

Mechanical and Aerospace Engineering Dissertations - Archive

Modern rotating machines are often required to operate with a small physical footprint and/or overall weight; necessitating that they utilize wide-ranging shaft speed to accomplish needed power levels. It is not uncommon that these designs also be required to support operation through a speed range encompassing multiple Critical Speeds while also limiting flexural vibrations to acceptable levels. Design optimization of this class of problem can be particularly difficult in that responses can be highly multi-modal and, when coupled with Finite Element (FE) solvers meet the conditions of a High Dimensional, Computationally Expensive Black Box (HEB) system. Because of this, some …

The Impact Of Electrostatic Correlations On The Electrokinetics, Elaheh Alidoosti

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this project we are interested in electrokinetics phenomenon (i.e., study of electrical charges in a liquid matter) and focus on three families of this phenomenon, dielectrophoresis, electro-osmosis and streaming current. For the first work, at concentrated electrolytes, the ion-ion electrostatic correlations effect is considered as an important factor in electrokinetics. In this project, we compute, in theory and simulation, the dipole moment for a spherical particle (charged, dielectric) under the presence of an alternating electric field using the modified continuum Poisson-Nernst-Planck (PNP) model by Bazant et al. (Phys. Rev. Lett. 106, 2011) [25]. We investigate the dependency of the …

Discrete Vortex Modeling Of Aerodynamic Flutter Of A Flat Plate With Damped Oscillations, Emma Chao

UNLV Theses, Dissertations, Professional Papers, and Capstones

Aerodynamic flutter is the unstable oscillation of a body caused by the interaction of aerodynamic forces, structural elasticity, and inertial effects induced by vortex shedding. Current models of this phenomenon require finite element analysis and extensive computational power and processing time. The purpose of this study was to develop and validate a program that is faster and more efficient than existing approaches by using the discrete vortex method (DVM). By reducing the complexities of flutter to the shedding of vortices in an inviscid model of a two-dimensional flat plate with a torsional spring constant at its center, this phenomenon can …

3d Parametric Hand To Improve Prosthetic Hand Functionality, Maria C. Gerardi

UNLV Theses, Dissertations, Professional Papers, and Capstones

The use of prosthetics can significantly enhance an individual’s standard of living, not only offering functional advantages but psychological advantages as well. Unfortunately for children with upper limb reduction, options are limited and rejection rates are high due to a multitude of reasons including discomfort and poor functionality. This study proposes a new parametric 3D design model (Parametric Hand) with an adjustable thumb that can be easily manipulated to the uniqueness of an individual. The Parametric Hand was evaluated, both qualitatively and quantitatively, against the Flexy-Hand 2, a commonly used prosthetic hand. The results showed insignificant differences in all testing …

Material Characterization Of Fiber-Reinforced Composite Materials Under Dynamic Loading Condition, Abu Iqbal

UNLV Theses, Dissertations, Professional Papers, and Capstones

Fiber reinforced composites are light materials which exhibits great strength and stiffness. They also have good dimensional stability and impact resistance. They reduce mass and improve structural performance, so the demand for fiber reinforced composite materials increases day by day in various industries such as aeronautical, automobile and military. The analysis, design, and optimization of polymer composite materials under static loading conditions are mature fields of study. Many sources are available to find material properties and predict structural response. However, composite materials are often used in extreme environments where they are subject to shock, impact, and blast loading. Efficient computational …

3-D Silk Fibroin Porous Particles Created By The Ouzo Effect For Biomedical Applications, Ashley Nicole Lamb

UNLV Theses, Dissertations, Professional Papers, and Capstones

Due to its high biocompatibility and biodegradability, silk fibroin – produced from

Bombyx mori (B. mori) cocoons – has been at the forefront of research for many

biomedical application formats: hydrogels, films, microspheres, and porous

sponges/scaffolding, to name a few. For drug delivery, in particular, porous particles are

desirable for their large surface area, uniform and tunable pore structure, and high

porosity. This thesis focuses on the fabrication of porous particles from silk fibroin by the

very interesting Ouzo effect. The Ouzo effect, so named because of the Greek

beverage ouzo, describes the phenomenon of an ethanol + anethole oil …

Numerical And Experimental Analysis Of Air-Cooled Condensers, Kaipo Kekaula

UNLV Theses, Dissertations, Professional Papers, and Capstones

The scope of this project is to numerically and experimentally dry cooling process in air-cooled condensers (ACCs) designed for concentrated solar power (CSP) applications. This effort is driven by the growing economic and political pressure to reduce water consumption during power generation due to limited water resources in the arid geographic climate of the southwestern United States. A computational approach is used in conjunction with experimental validation to gain a more complete understanding of these systems.

Traditionally research into ACCs have been largely limited to air-side heat transfer modelling as it accounts for a large portion of the total thermal …

Machine Learning Modeling Of Horizontal Photovoltaics Using Weather And Location Data, Christil Pasion, Torrey Wagner, Clay Koschnick, Steven Schuldt, Jada Williams, Kevin Hallinan

Mechanical and Aerospace Engineering Faculty Publications

Solar energy is a key renewable energy source; however, its intermittent nature and potential for use in distributed systems make power prediction an important aspect of grid integration. This research analyzed a variety of machine learning techniques to predict power output for horizontal solar panels using 14 months of data collected from 12 northern-hemisphere locations. We performed our data collection and analysis in the absence of irradiation data-an approach not commonly found in prior literature. Using latitude, month, hour, ambient temperature, pressure, humidity, wind speed, and cloud ceiling as independent variables, a distributed random forest regression algorithm modeled the combined …

Additive Manufacturing Of Dense We43 Mg Alloy By Laser Powder Bed Fusion, Holden Hyer, Le Zhou, George Benson, Brandon Mcwilliams, Kyu Cho, Yongho Sohn

Mechanical Engineering Faculty Research and Publications

WE43 is a high-strength, corrosion-resistant Mg-alloy containing rare earths such as Y and Nb, and has potential for many lightweight structural or bioresorbable prosthetic applications. In this study, additive manufacturing of dense WE43 alloy by laser powder bed fusion (LPBF) from gas atomized powders has been accomplished through studies involving single track scan of wrought WE43, parametric variation of LPBF, microstructural analysis and mechanical testing, both in compression and tension. The Archimedes method and image analyses from optical micrographs were employed to document the LPBF of dense (>99 % relative density) WE43 using optimum parameters of 200 W laser …

Mathematical Modeling Of A Variable Mass Rocket’S Dynamics Using The Differential Transform Method, Ashwyn Sam

Honors Theses

In this paper, the mathematical modelling of a rocket with varying mass is investigated to construct a function that can describe the velocity and position of the rocket as a function of time. This research is geared more towards small scale rockets where the nonlinear drag term is of great interest to the underlying dynamics of the rocket. A simple force balance on the rocket using Newton’s second law of motion yields a Riccati differential equation for which the solution yields the velocity of the rocket at any given time. This solution can then be integrated with respect to time …

Materials-Processing Relationships For Metal Fused Filament Fabrication Of Ti-6al-4v Alloy., Paramjot Singh

Electronic Theses and Dissertations

Additive manufacturing (AM) is at the mainstream to cater the needs for rapid tooling and small-scale part production. The metal AM of complex geometries is widely accepted and promoted in the industry. While several metal AM technologies exist and are matured to a level where expectation in terms of design and properties are possible to realize. But the metal AM suffers from the heavy expense to acquire equipment, isotropic property challenges, and potential hazards to work with loose reactive metal powder. With this motivation, the dissertation aims to develop the fundamental aspects to print metal parts with bound Ti-6Al-4V powder …

Selective Laser Melting 17-4 Ph Stainless Steel And The Effect Of Varied Thermal Treatments On Fatigue Behavior., Sean Daniel Dobson

Electronic Theses and Dissertations

Fatigue failure is the leading source of loss in industry. In order for new means of manufacturing to move towards mainstream use a complete understanding of material and mechanical behavior must be gained. This endeavor seeks to aide in that task by observing the fatigue behavior of selective laser melting (SLM) additive manufacturing (AM) specimens and the effect of differing thermal treatment conditions for an optimized AM process. Stainless steel 17-4 PH specimens were fabricated using SLM AM and thermally treated to three conditions: as-built, solutionized and hardened, and direct hardened. These specimens were characterized for material (powder quality, density, …

Assessing The Impact Of Drop Velocity And Spacing In Binder Jetting To Improve Printing In Novel Powders And New Environments, Trenton Colton

Utah Space Grant Consortium

Binder Jetting (BJ) is a low-cost Additive Manufacturing (AM) process that uses inkjet technology to selectively bind particles in a powder bed. The interaction of the binder droplets with the powder is essential to the process. This is a complex interaction in which picoliter-sized droplets impact powder beds at velocities of approximately 10 m/s. The binder partially fills the voids between the powders. The fraction of void space filled with binder is the saturation and is a key parameter in BJ. The effects of printing parameters such as droplet velocity, size, and spacing on saturation levels are unknown. This study …

Effect Of Superhydrophobic Surface Microstructure On Transient Jet Impingement Cooling, D. Jacob Butterfield, John Morris

Utah Space Grant Consortium

Jet impingement is an effective method of rapid surface cooling, and is highly dependent on surface condition and properties. Here, silicon surfaces are modified by ion-etching different micropatterns (posts or holes) on one side and coated with Teflon to make them superhydrophobic (SH). The other side of the surface has a screen-printed resistance heater. Surfaces are heated to temperatures between 200 to 320 °C, and then impinged on by a pure water jet at room temperature with flow rates ranging from 6 to 18 mL/s. Results show that there is little effect of microstructure, although hole surfaces and shorter microstructures …

Design And Demonstration Of Automated Technologies For The Fabrication And Testing Of Pem Fuel Cell Systems, Vladimir Gurau, Daniel Cox, Devin C. Fowler, Matthew Carter, Adedayo Ogunleke

Manufacturing Engineering: Faculty Publications (2015-2023)

This paper describes the research efforts at Georgia Southern University to develop robotic technologies for the fabrication of fuel cell components and stacks, as well as the design and fabrication of a High Temperature Proton Exchange Membrane Fuel Cell (HT-PEMFC) power system to be used as motive power and auxiliary power unit (APU) for a long range, unmanned, fully autonomous forest rover. The paper describes a manufacturing workcell consisting of a Yaskawa Motoman SDA5F dual arm robot with machine vision used for sorting, reorientation and stacking fuel cell components in presenters in preparation for their subsequent robotic assembly in fuel …

A History And Status Of Wind Energy Potential In Arkansas, Pre And Post Covid-19, Will Blasingame

Mechanical Engineering Undergraduate Honors Theses

Historically, wind-generated electricity has been the largest renewable energy sources in the United States. Wind-rich regions like Oklahoma and Texas have fueled growth and sold that electricity to electric utilities located in wind-poor states like Arkansas in the form of Power Purchase Agreements. Future technologies such as Vertical Axis Wind Turbines, small wind turbines, and Tesla turbines designed to generate electricity from wind show promise in unlocking more expensive wind resources in regions like Northwest Arkansas by mitigating concerns about low wind speeds and noise. However, more factors than just feasibility influence the growth of wind power. Governmental policies such …

Construction Of A Hyperspectral Imager Using 3d-Printed And Off-The-Shelf Components, Joshua Moorhouse

Mechanical Engineering Undergraduate Honors Theses

The Arkansas Center for Space and Planetary Sciences is working in collaboration with the Mechanical Engineering department to create a relatively cheap and modifiable hyperspectral imager. It is constructed using 3D-printed and off-the-shelf components from Edmund Optics and Amazon. The iteration created in this paper delivers spectrograms in the visible spectrum. The long-term goals of the camera are to create hyperspectral images from these spectrograms and to advance the imager into the infrared and near-infrared spectra. This imager is being developed to be used in the Arkansas Center for Space and Planetary Sciences environmental test chambers to further the scientific …

Enhancement Of Phase Change Material Sorbitol By Nanoparticle Inclusion For Improving Thermal Energy Storage Capabilities, Joshua Kasitz

Mechanical Engineering Undergraduate Honors Theses

Thermal management of electronic devices has become an increasingly vital field of study with the rapid miniaturization of many key electrical components. With the significant improvement of semiconductor manufacturing and intensified focus on interconnects, electronic devices have decreased in size at an incredible rate. Decreasing spatial requirements is essential to improving device capabilities as the electronic system is able to incorporate more components. Currently, electronic systems are drastically limited by the capabilities of their cooling mechanisms. Smaller devices lead to large increases in the energy density of the system and require more powerful cooling systems to maintain proper component operating …

Spherical Cavity Expansion Approach For The Study Of Rigid-Penetrator’S Impact Problems, Mario Buchely, Alejandro Marañon

Materials Science and Engineering Faculty Research & Creative Works

In recent years, Spherical Cavity Expansion (SCE) theory has been extensively utilized to model dynamic deformation processes related to indentation and penetration problems in many fields. In this review, the SCE theory is introduced by explaining the different mathematical features of this theory, its solution, and a potential application to model the penetration of a rigid penetrator into a deformable target. First, a chronologically literature review of the most common models used to study this kind of penetration problems is introduced, focusing on the SCE theory. Then, the engineering model of penetration is presented using the SCE approach. The model …

Analog Versus Digital Guitar Pedals, Shaping Guitar Tones And Sparking Debates, Cameron Karren

Capstone Projects and Master's Theses

This paper goes into the history of guitar effects, what exactly they are, how they have evolved, and what they are like today. It also presents the results of an experiment that compares perceptions of differences between analog and digital guitar pedals.

Computational Analysis Of A New Planar Mixing Layer Flame Configuration To Study Soot Inception, Carmen Ciardiello

Honors Scholar Theses

The production of soot is omnipresent in society today. Soot is the product of many of the combustion processes that provide the bulk of the usable energy throughout the world. Furthermore, soot particulate poses a great danger to both the environment and all forms of life on Earth. It has proven to pollute ecosystems, foster health problems for human beings, and degrade air quality [1].

These dangers make studying and understanding soot particulate paramount for improving the quality of life. Thus, this study introduces a new flame configuration for studying soot inception. Presently, various common flame configurations have been found …

Thermodynamic Potential Of Very High Performance Fuel Cells, Kimberly Liang

Honors Scholar Theses

Fuel Cells are devices that use the chemical energy of a fuel (e.g. hydrogen) to electrochemically produce electricity. Similar to a conventual combustion engine, a fuel cell will continue to run and generate electricity as long as fuel is supplied. However, unlike a conventional combustion engine, fuel cells have a much higher theoretical efficiency and do not directly emit harmful air pollutants. This project will focus on a fuel cell that uses hydrogen as fuel and oxygen as an oxidizing agent.

As fuel cell technology evolved, high pressure fuel cell systems became of interest in portable applications, such as submarine …

An Assessment Of Renewable Energy Technology Implementation In Storrs, Connecticut: Emissions Reduction And Feasibility Of A Microgrid System At Uconn, Sophie Macdonald

Honors Scholar Theses

The purpose of this project is to design a clean energy-sourced microgrid for UConn’s main campus that would reduce the university’s energy emissions while remaining within the geographic boundaries of viable UConn-owned land. Economic cost was not considered in this analysis; instead, emissions and space constraints were the optimized measures of value and feasibility. Sources of energy that were considered include photovoltaics (PV), wind turbines, hydrokinetic systems, and fuel cells. Energy storage capacity was included in the analysis as well. The overall system was optimized first by ignoring space constraints and for a minimum of 10% reduction from the current …

Development Of Vegetable Oil Based Nano-Lubricants, Vicente Cortes

Theses and Dissertations

Nowadays, the depletion of crude oil reserves in the world and the global concern in protecting the environment from contamination have renewed interest in developing environment friendly lubricants derived from alternative sources such as vegetable oils. Mineral oil is the most common lubricant, however, it also has poor biodegradable properties. Vegetable oils exhibit good viscosity index, flash point, pour point, tribological properties, and are biodegradable. Furthermore, the use of nanoparticles as additives has shown to improve anti wear and anti-friction properties of the base lubricant. The present research project will evaluate experimentally the rheological and tribological behavior of coconut oil, …

Processing And Microstructural Characterization Of Silicon Carbide, Silicon Nitride, And Tungsten Carbide Fibers, Christian Garcia

Theses and Dissertations

This research focuses on developing polymer-derived ceramic fibers. The spun micro/nanofibers were sintered into silicon carbide/silicon nitride and tungsten carbide respectively. The relationship between processing, fiber microstructure, morphology, and purity is investigated by scanning electron microscopy, Fourier transform infrared spectroscopy, energy-dispersive X-ray spectroscopy, and thermogravimetric analysis. Dynamic Mechanical Analysis was used to test the reinforcement capabilities of tungsten carbide fibers. EDS identified a near-perfect 1:1 Si-C ratio in silicon carbide fibers sintered between 1200 °C -1400 °C, Silicon carbide was confirmed by FTIR between 1000 °C – 1400 °C. Silicon Nitride peaks were noted in FTIR between 1200 °C – …

Residual Service Life Prognostic Models For Tapered Roller Bearings, Jennifer Danni Lima

Theses and Dissertations

There are a few different bearing health monitoring technologies currently used in the railroad industry, both reactive and preventative detection systems. Reactive models have proven to be ineffective in monitoring bearing health, which has resulted in either unnecessary train stoppages and delays or in-service failures and bearing burn-off leading to catastrophic train derailments. Wayside preventative detection systems, while more effective than reactive technologies, are scarce and neglect railcars’ that do not travel over a specific route. This knowledge prompted the University Transportation Center for Railway Safety at UTRGV to develop an onboard bearing health monitoring system that can accurately assess …

Bio-Inspired Wings In High Freestream Turbulence: A Numerical And Experimental Study, Alexia Martinez Ibarra

Theses and Dissertations

The aerodynamics and flow field characteristics of a NACA 0010 airfoil with leading-edge modifications were investigated in flow with freestream turbulence intensity of 4%. A set of 4 airfoils, each of them with different wavelength (4, 8, 10, 12 tubercles along the spanwise direction) was experimentally studied. An unmodified NACA 0010 airfoil was used as baseline. The Reynolds number was varied from 201,200 to 351,600. The angle of attack was varied within the range of -6 to 20 degrees. Several techniques were used to investigate the characteristics of the airfoils such as wake profile surveys, 6-axis force measurements, and Particle …

The Development And Evaluation Of A New Analytical Model For The Characterization Of Friction Induced Disc Brake Vibration, Michael Vladimirov

Master's Theses

This research proposes a new method of modeling vibration of disc brake systems. This modeling method treats the brake pads of a disc braking system as lumped spring-mass-damper subsystems and the disc as a continuous bar. This modeling concept increases both the ease of analytical expression and the insight provided into the behavior of the real-world systems. This paper describes the analytical expression of this model and its implementation in Matlab. A parameter variation study yielded results that agree with existing research, which serves to validate the fundamental principles of this proposed modeling method.