Mechanical Engineering Commons^™

Hemodynamic Response To Device Titration In The Shunted Single Ventricle Circulation - A Patient Cohort Modeling Study, Chet Villa, Farha Zafar, Angela Lorts, Ethan Kung

Publications

Clinical outcomes of ventricular assist device (VAD) support for shunted single ventricle patients trail the larger population due in part to the challenges in optimizing VAD support and balancing systemic and pulmonary circulations. We sought to understand the response to VAD titration in the shunted circulation using a lumped-parameter network modeling six patient-specific clinical cases. Hemodynamic data from six patients (mean body surface area = 0.30 m²) with a systemic-to-pulmonary shunt was used to construct simulated cases of heart failure and hemodynamic response to increasing VAD flow from 5 to 10 L/min/m². With increasing VAD flow, …

Half-Barrel Planter Mover, Mihir Shah, Natalie Lewis, Mason James Hughes

Mechanical Engineering

A device for transporting heavy barrel planters is needed. Barrel planters are wooden wine barrels that have been cut in half along the circumference. They are used to store and grow a variety of plants. As such, they can contain more than 300 pounds of soil. The products currently on the market are not designed for such heavy planters, are cost prohibitive, and do not take advantage of the tapered design of a wine barrel half. A solution is needed that is durable, easy to use, and low cost. This final design report will show the steps used to find …

Fsae Chassis Hardpoint Optimization, Christopher Soohoo, Ethan Vallivero, Dwarak Reddy

Mechanical Engineering

Our team has been tasked with optimizing hardpoints for the Cal Poly Racing team. Hardpoints are the locations on the chassis of a car that are designed to carry both internal and external loads, they are the areas where the engine and suspension connect to the chassis. These points are subject to torsion, shear, bending and pull-out loads. Cal Poly Racing needs more thoroughly analyzed individualized hardpoints that are optimized for weight, strength and specific stiffness, so they can reduce the overall weight and improve the race times of the vehicle while maintaining their strength and stiffness standards. Our team …

Time-Dependent System Reliability Analysis With Second-Order Reliability Method, Hao Wu, Zhangli Hu, Xiaoping Du

Mechanical and Aerospace Engineering Faculty Research & Creative Works

System reliability is quantified by the probability that a system performs its intended function in a period of time without failures. System reliability can be predicted if all the limit-state functions of the components of the system are available, and such a prediction is usually time consuming. This work develops a time-dependent system reliability method that is extended from the component time-dependent reliability method using the envelope method and second-order reliability method. The proposed method is efficient and is intended for series systems with limit-state functions whose input variables include random variables and time. The component reliability is estimated by …

Common Pool Resource Management: Assessing Water Resources Planning For Hydrologically Connected Surface And Groundwater Systems, Francisco Munoz-Arriola, Tarik Abdel-Monem, A. Amaranto

Department of Mechanical and Materials Engineering: Faculty Publications

Common pool resource (CPR) management has the potential to overcome the collective action dilemma, defined as the tendency for individual users to exploit natural resources and contribute to a tragedy of the commons. Design principles associated with effective CPR management help to ensure that arrangements work to the mutual benefit of water users. This study contributes to current research on CPR management by examining the process of implementing integrated management planning through the lens of CPR design principles. Integrated management plans facilitate the management of a complex common pool resource, ground and surface water resources having a hydrological connection. Water …

Part-Scale Thermal Simulation Of Laser Powder Bed Fusion Using Graph Theory: Effect Of Thermal History On Porosity, Microstructure Evolution, And Recoater Crash, Reza Yavari, Ziyad Smoqi, Alex Riensche, Ben Bevans, Humaun Kobir, Heimdall Mendoza, Hyeyun Song, Kevin Cole, Prahalada Rao

Department of Mechanical and Materials Engineering: Faculty Publications

Flaw formation in laser powder bed fusion (LPBF) is influenced by the spatiotemporal temperature distribution – thermal history – of the part during the process. Therefore, to prevent flaw formation there is a need for fast and accurate models that can predict the thermal history as a function of the part shape and processing parameters. In previous work, a thermal modeling approach based on graph theory was used to predict the thermal history in LPBF parts in less-than 20% of the time required by finite element-based models with error within 10% of experimental measurements. The present work transitions toward the …

Accelerated Controller Tuning For Wind Turbines Under Multiple Hazards, Aly Mousaad Aly, Milad Rezaee

Faculty Publications

During their lifecycle, wind turbines can be subjected to multiple hazard loads, such as high-intensity wind, earthquake, wave, and mechanical unbalance. Excessive vibrations, due to these loads, can have detrimental effects on energy production, structural lifecycle, and the initial cost of wind turbines. Vibration control by various means, such as passive, active, and semi-active control systems provide crucial solutions to these issues. We developed a novel control theory that enables semi-active controller tuning under the complex structural behavior and inherent system nonlinearity. The proposed theory enables the evaluation of semi-active controllers’ performance of multi-degrees-of-freedom systems, without the need for time-consuming …

Project G.H.O.S.T., Matthew Morell, Austin Conrad, Zackeris Gordon, Conan Estes

Mechanical Engineering

Project G.H.O.S.T aimed to produce a model transmission with a control system for high performance/racing electric vehicles to utilize the full capability of the electric motor at higher speed applications. Current electric vehicles have a large amount of torque and use a fixed gear ratio that compromises between both high and low speeds with performance peaking around 65 miles per hour. A typical electric motor used in this application has approximately 1800 ft-lbs of torque up to 5,000 rpm. Past approximately 5,000 rpm, the torque rapidly drops off and so does the overall vehicle performance. Though transmissions exist that could …

Smud Solar Regatta, Logan Garby, Nam Le, Jacob Singer, Alejandro Carrera, Laura Casas

Mechanical Engineering

The Sacramento Municipal Utility District (SMUD) hosts the Solar Regatta every year in Rancho Seco, CA, a competition which consists of teams building a solar powered boat to compete in three races: the sprint race, endurance race, and slalom race. The Cal Poly Solar Regatta team was informed mid-project by SMUD that the competition has been canceled once again for spring 2021, but the team decided to move forward with the construction of the boat. The previous Cal Poly team from 2019/2020 designed the hull and propulsion system of the boat. The 2020/2021 team worked with the previous team in …

Enduro Campers, Ryan J. Shomsky, Alexander W. Horst, Kevin S. Pickering, Jackson L. Aplanalp, Luke Arana, Will Firestone

Mechanical Engineering

The Enduro Campers senior project team (Formerly known as Lobo Campers senior project team) was recruited by Mr. Leif Stein to assist in the design, manufacturing, and testing of the materials and components of his company’s expedition box camper. The two main focuses of the project, divided into two sub-teams, were on the testing and manufacturing process of the materials used in the camper, and on the design and analysis of the camper’s access door, step box, and other subsystems.

The focus of the materials analysis and manufacturing team was based around the design parameter to use composite sandwich panels …

Final Design Report Cal Poly Wind Power - Balancing System, Caleb Seth Cross, Ethan Andrew Czuppa

Mechanical Engineering

The Cal Poly Wind Power club is anticipating joining the annual Collegiate Wind Competition in the year 2021. This competition hosts schools from all around the country, who meet and compete against each other by testing the wind turbines they have made throughout the academic school year. Tasks included in the competition test the wind turbine’s efficiency, power generation, overall design, and stability in extreme conditions.

Cal Poly is planning to implement a formal balancing system to support their 2021 wind turbine. Our senior project team undertook mitigating mass imbalance in the wind turbine; mass imbalance occurs when the center …

The Corrosion Of Stainless Steel Made By Additive Manufacturing: A Review, Gyeongbin Ko, Wooseok Kim, Kyungjung Kwon, Tae-Kyu Lee

Mechanical and Materials Engineering Faculty Publications and Presentations

The advantages of additive manufacturing (AM) of metals over traditional manufacturing methods have triggered many relevant studies comparing the mechanical properties, corrosion behavior, and microstructure of metals produced by AM or traditional manufacturing methods. This review focuses exclusively on the corrosion property of AM-fabricated stainless steel by comprehensively analyzing the relevant literature. The principles of various AM processes, which have been adopted in the corrosion study of stainless steel, and the corrosion behaviors of stainless steel depending on the AM process, the stainless steel type, and the corrosion environment are summarized. In this comprehensive analysis of relevant literature, we extract …

A Hybrid Droplet Vaporization-Adaptive Surrogate Model Using An Optimized Continuous Thermodynamics Distribution, Simcha L. Singer, Michael Hayes, Alanna Y. Cooney

Mechanical Engineering Faculty Research and Publications

Liquid transportation fuels are composed of hundreds of species, necessitating the use of surrogates in CFD simulations. Surrogates composed of a few species are often formulated to emulate the combustion properties targets (CPTs) of pre-vaporized fuels but fail to reproduce their vaporization behavior, implying that such surrogates cannot replicate the CPTs in the presence of preferential vaporization. The prevailing approach to this problem proposes a physical–chemical surrogate formulated to match the fuel’s distillation curve in addition to its CPTs. However, the physical–chemical surrogate approach requires more species, may not reproduce the instantaneous (distillation-resolved) CPTs, and is not well-suited to conditions …

Me-Em Enewsbrief, March 2021, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Cal Poly Wind Power - Blade Pitching System, Jenna Hartley, Ben Santos, Willie Bass

Mechanical Engineering

The Cal Poly Wind Power club (CPWP) has sponsored our senior project team to design and implement a system to dynamically pitch the blades of their prototype horizontal-axis wind turbine. A blade pitching system can improve a turbine’s efficiency under certain operating conditions and prevent failure under extreme wind speeds. To ensure reliable control, the pitching system must be able to pitch quickly and accurately. Turbine efficiency can be improved by a pitching system with low power draw and low inertia about the rotor axis. The turbine is subjected to static and dynamic loading occurring due to changing aerodynamic forces, …

Adaptive Kriging Method For Uncertainty Quantification Of The Photoelectron Sheath And Dust Levitation On The Lunar Surface, Xinpeng Wei, Jianxun Zhao, Xiaoming He, Zhen Hu, Xiaoping Du, Daoru Han

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents an adaptive Kriging based method to perform uncertainty quantification (UQ) of the photoelectron sheath and dust levitation on the lunar surface. The objective of this study is to identify the upper and lower bounds of the electric potential and that of dust levitation height, given the intervals of model parameters in the one-dimensional (1D) photoelectron sheath model. To improve the calculation efficiency, we employ the widely used adaptive Kriging method (AKM). A task-oriented learning function and a stopping criterion are developed to train the Kriging model and customize the AKM. Experiment analysis shows that the proposed AKM …

2021 (Spring) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the spring of 2021.

Geophysical Observations Of Taliks Below Drained Lake Basins On The Arctic Coastal Plain Of Alaska, R. C. Rangel, A. D. Parsekian, L. M. Farquharson, B. M. Jones, N. Ohara, A. L. Creighton, B. V. Gaglioti, M. Kanevskiy, A. L. Breen, H. Bergstedt, V. E. Romanovsky, K. M. Hinkel

Michigan Tech Publications, Part 1

Lakes and drained lake basins (DLBs) together cover up to ∼80% of the western Arctic Coastal Plain of Alaska. The formation and drainage of lakes in this continuous permafrost region drive spatial and temporal landscape dynamics. Postdrainage processes including vegetation succession and permafrost aggradation have implications for hydrology, carbon cycling, and landscape evolution. Here, we used surface nuclear magnetic resonance (NMR) and transient electromagnetic (TEM) measurements in conjunction with thermal modeling to investigate permafrost aggradation beneath eight DLBs on the western Arctic Coastal Plain of Alaska. We also surveyed two primary surface sites that served as nonlake affected control sites. …

Wind Blade Manufacturing For The Cal Poly Wind Power Club, Benjamin E. Thompson, Jake R. Lund, Claudia C. Angeles

Mechanical Engineering

The Cal Poly Wind Power Club is entering the 2021 Collegiate Wind Competition (CWC) in June. Last year, three senior project teams were assigned to collaborate and assist the club with the pitching mechanism, the rotor balancing, and the manufacturing process. As the manufacturing team, the goal of our project was to design a manufacturing process for the bladegeometry given. The manufacturing process was required to meet the team’s expectations and CWC’s performance requirements to place highly in the competition taking place in June 2021.These expectations included creating a manufacturing process that is repeatable and reliable for future competitions. The …

Robust Scandium Aluminum Nitride Mems Resonators For L Band Operation In Orbital Environments, Israel W. Dunk

Theses and Dissertations

This thesis investigates AlN alloyed with scandium in a variety of resonator architectures including WEM, overtone WEM, LEM, and SAW that have the potential to achieve high levels of electrical performance and environmental robustness. SAW resonators operating near 370 MHz are fabricated on polycrystalline Sc_.37Al_.63N, and AlN with the resulting devices compared and conclusions drawn as to the merits of each material. The design and fabrication of SAW devices is discussed in detail, with the operating characteristics of these resonators then tested both electrically and mechanically. Mechanical characterisation includes analysis of vibration and shock effects on …

Tunable Cspb(Br/Cl)3 Perovskite Nanocrystals And Further Advancement In Designing Light Emitting Fiber Membranes, Sk Shamim Hasan Abir, Santosh K. Gupta, A. Ibrahim, Bhupendra B. Srivastava, Karen Lozano

Mechanical Engineering Faculty Publications

Cesium lead halide perovskite nanocrystals (NCs) have drawn a great deal of interest in optoelectronic and photonic applications due to their intrinsic and attractive photoluminescence properties. Though, their commercially viability is of concern due to their intrinsic instability. In this study, blue and green luminous PMMA-CsPbX3(X=Cl/Br) fibers were fabricated via forcespinning technique, where the polymer matrix encapsulated the NCs. Blue CsPbX3 NCs (b- CPX NCs) were synthesized at ambient conditions while blue to green CsPbX3 NCs (g-CPX NCs) fine color tuning was obtained after heat treatment at 150°C.Field emission scanning electron microscopy (FESEM) shows fibers with diameters in the single …

On Road Coordinates For Autonomous Vehicle Guidance, Ricardo Jacome

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A new roadmap framework is proposed to improve the guidance and trajectory prediction capabilities of connected and automated vehicles (CAVs). Independent of road shape determination through external sensors, the system serves as a backup for challenging conditions, such as low sensor visibility and adverse environmental effects (e.g., rain, fog, snow). Based on the fusion of vehicle dynamics principles, differential geometry, and road design standards, the roadmap framework provides a consolidated collection of critical reference points of roadway centerlines and information about the shape of the roadway in the vicinity of a vehicle, including curvature, optimal travel velocity, and road alignment …

Moving Hands-On Mechanical Engineering Experiences Online: Course Redesigns And Student Perspectives, Jaclyn E. Johnson, Nancy B. Barr

Michigan Tech Publications, Part 1

Hands-on lab experiences are essential for enabling students to be successful engineers, especially those who identify as kinesthetic learners. This case study describes how a Mechanical Engineering Practice course sequence was redesigned during the COVID-19 emergency transition to remote learning and examines how students responded to these changes. The remote course included videos of Graduate Teaching Assistants conducting data acquisition phases of the practice session to replace hands-on experiments. To understand student perspectives and performance, researchers reviewed approximately 400 reflective essays from Spring 2020 and compared assignment submissions between Fall 2019 and Spring 2020. Results suggest that some students perceived …

Condition Monitoring And Fault Detection Of Blade Damage In Small Wind Turbines Using Time-Series And Frequency Analyses, Luke H. Costello

Master's Theses

Condition monitoring systems are critical for autonomous detection of damage when operating remote wind turbines. These systems continually monitor the turbine’s operating parameters and detect damage before the turbine fails. Although common in utility-scale turbines, these systems are mostly undeveloped in distributed, small-scale turbines due to their high cost and need for specialized equipment. The Cal Poly Wind Power Research Center is developing a low-cost, modular solution known as the LifeLine system. The previous version contained monitoring equipment, but lacked decision-making capabilities.

The present work builds on the LifeLine by developing software-based detection of blade damage. Detection is done by …

Development Of Novel Hardware And Software For Wind Turbine Condition Monitoring, Ryan A. Zhan

Master's Theses

With the increased use of wind turbines as sources of energy, maintenance of these devices becomes more and more important. Utility scale wind turbines can be time consuming and expensive to repair so an intelligent method of monitoring these devices is important. Commercial solutions for condition monitoring exist but are expensive and can be difficult to implement. In this project a novel condition monitoring system is developed. The priority of this system, dubbed the LifeLine, is to provide reliable condition monitoring through an easy-to-install and low-cost system. This system utilizes a microcontroller to collect acceleration data to detect imbalances on …

Experimental Investigation Of The Effects Of Acoustic Waves On Natural Convection Heat Transfer From A Horizontal Cylinder In Air, Katherina V. Prodanov

Master's Theses

Heat transfer is a critical part of engineering design, from the cooling of rocket engines to the thermal management of the increasingly dense packaging of electronic circuits. Even for the most fundamental modes of heat transfer, a topic of research is devoted to finding novel ways to improve it. In recent decades, investigators experimented with the idea of exposing systems to acoustic waves with the hope of enhancing thermal transfer at the surface of a body. Ultrasound has been applied with some success to systems undergoing nucleate boiling and in single-phase forced and free convection heat transfer in water. However, …

Ram Air-Turbine Of Minimum Drag, Raymond Akagi

Master's Theses

The primary motivation for this work was to predict the conditions that would yield minimum drag for a small Ram-Air Turbine used to provide a specified power requirement for a small flight test instrument called the Boundary Layer Data System. Actuator Disk Theory was used to provide an analytical model for this work.

Classic Actuator Disk Theory (CADT) or Froude’s Momentum Theory was initially established for quasi-one-dimensional flows and inviscid fluids to predict the power output, drag, and efficiency of energy-extracting devices as a function of wake and freestream velocities using the laws of Conservations of Mass, Momentum, and Energy. …

Thermal Ignition Of A Combustible Over An Inclined Hot Plate, Salaika Parvin, Nepal Chandra Roy, Rama S. R. Gorla

Faculty Publications

In this study, the ignition characteristics and the flow properties of the mixed convection flow are presented. Detailed formulations of the forced, natural and mixed convection problems have been discussed. In order to avoid inconvenient switch between the forced and natural convection we introduce a continuous transformation in the mixed convection. We make a comparison between these situations which reveal a good agreement. For mixed convection flow, the ignition distance is explicitly expressed as a function of the Prandtl number, reaction parameter and wall temperature. It has been observed that owing to the increase of the aforesaid parameters, the thermal …

Chilling And Heat Accumulation Of Fruit And Nut Trees And Flower Bud Vulnerability To Early Spring Low Temperatures In New Mexico: Meteorological Approach, Koffi Djaman, Komlan Koudahe, Murali Darapuneni, Suat Irkmak

Department of Mechanical and Materials Engineering: Faculty Publications

Fruit and nut trees production is an important activity across the southwest United States and this production is greatly impacted by the local climate. Temperature is the main environmental factor influencing the growth and the productivity of the fruit and nut trees as it affects the trees’ physiology and the vulnerability of flower bud, flowers, and young fruit and nut to the low temperatures or spring frost. The objective of the present study is to estimate the chilling and heat accumulation of fruit and nut trees across New Mexico. Three study sites as Fabian Garcia, Los Lunas, and Farmington were …

Local And Systemic In Vivo Responses To Osseointegrative Titanium Nanotube Surfaces, Erin A. Baker, Mackenzie M. Fleischer, Alexander D. Vara, Meagan R. Salisbury, Kevin C. Baker, Paul T. Fortin, Craig R. Friedrich

Michigan Tech Publications, Part 1

Orthopedic implants requiring osseointegration are often surface modified; however, implants may shed these coatings and generate wear debris leading to complications. Titanium nanotubes (TiNT), a new surface treatment, may promote osseointegration. In this study, in vitro (rat marrow-derived bone marrow cell attachment and morphology) and in vivo (rat model of intramedullary fixation) experiments characterized local and systemic responses of two TiNT surface morphologies, aligned and trabecular, via animal and remote organ weight, metal ion, hematologic, and nondecalcified histologic analyses. In vitro experiments showed total adherent cells on trabecular and aligned TiNT surfaces were greater than control at 30 min and …