Mechanical Engineering Commons^™

Effects Of Acoustic Environments On Speech Comprehension By Native-English-Speaking Listeners, Zhao Peng, Lily M. Wang, Siu Kit Lau

Durham School of Architectural Engineering and Construction: Faculty Publications

This study investigates the effects of acoustic conditions on speech comprehension, rather than speech intelligibility as often reported in existing literature. Sets of 15-minute-long listening comprehension tests were developed based on the format of the Test of English for International Communication (TOEIC). Each test set includes four types of tasks: matching aural phrases to photographs, selecting appropriate responses to aural questions, and answering questions after listening to conversations (between two talkers) and talks (single talker). Within the Nebraska acoustics test chamber, native-English-speaking participants are asked to perform these tests under 15 acoustic conditions, from combinations of three background noise levels …

Changes In In Vivo Knee Contact Forces Through Gait Modification, Allison Kinney, Thor F. Besier, Amy Slider, Scott L. Delp, Darryl D. D'Lima, Benjamin J. Fregly

Mechanical and Aerospace Engineering Faculty Publications

Gait modification represents a non-invasive method for reducing knee joint loading in patients with knee osteoarthritis. Previous studies have shown that a variety of gait modifications are effective in reducing the external knee adduction moment. The external knee adduction moment is often used as a surrogate measure of medial compartment force. However, a recent study showed that reductions in the external knee adduction moment do not guarantee reductions in medial compartment loads. Therefore, direct measurement of changes in knee contact force is important for determining the effectiveness of gait modifications. A previous study found that medial thrust gait and walking …

Gpu-Accelerated Modeling Of Microscale Atmospheric Flows Over Complex Terrain, Anthony Rey Deleon

Boise State University Theses and Dissertations

With installed wind power capacities steadily on the rise, balancing the loads on electrical grids is challenging due to the intermittency of the wind. Short-term wind power forecasting can be a valuable tool for better informing grid operators on the available wind power. Current short-term wind forecasting techniques typically adopt mesoscale weather forecasting models with spatial resolutions on the order of a kilometer. On relatively flat terrain, use of mesoscale models may prove effective, but application to complex terrain induces large forecasting errors. To address this issue, a baseline incompressible flow solver for GPU (graphics processing unit) clusters is extended …

A Case Study For Financial Feasibility Of Automated Costing Support In A Small Machine Shop, Benito A. Gonzalez

Theses and Dissertations - UTB/UTPA

A knowledge-based cost estimating expert system is chosen by a Mexican machine shop. Differences between the traditional experience-based system employed and the automated system are studied. Data is gathered to analyze time effectiveness, accuracy and payback of the software. Data from seventy part models is recorded to study the time experiment, and data from fifty part models is used to study the accuracy and consistency. Data is analyzed by calculating mean, standard deviation, and test of hypothesis. The results indicate that the software is faster than the traditional quoting system; however, the payback point is high. Also, results show the …

Load Sensor In An Elastomer Suspension Element, Jazmin Ley

Theses and Dissertations - UTB/UTPA

Knowledge of the loading applied to railcar suspension elements is necessary for improved rail safety, efficiency, and for monitoring bearing health. An economical, reliable system for keeping track of both dynamic and static loads on a rail car bearing offers potential for many improvements in rail service. The difficulties of implementing such a system are considerable because the sensor must be in the bearing load path and is thus subject to all the stressors of that environment including high impact, high load, high temperature, and corrosion. This thesis describes an attempt to incorporate a load measurement system in a polyurethane …

Absorber Geometry Optimization For A New Wave Energy Converter, Rachel A. Durren

Masters Theses

Alternative energy technologies are on the forefront of research due to the rising costs of oil and natural gas. One relatively under development source of energy is ocean waves. In order to make the use of ocean waves economically viable, the amount of energy absorbed by wave energy converters (WEC) must be optimized. The research within presents a new conceptual design, "Aqua Fly", for a WEC with emphasis on maximizing the amount of energy absorbed. The energy absorption component of the "Aqua Fly" was isolated and a small scale 2-D study of energy absorption. First, the amount of energy in …

2d Modeling Of Forcespinning™ Nanofiber Formation With Experimental Study And Validation, Simon Padron

Theses and Dissertations - UTB/UTPA

A newly developed method of producing nanofibers, called Forcespinning™, has proven to be a viable alternative to mass produce nanofibers. Forcespinning™ utilizes centrifugal forces which allow for a host of new materials to be processed into nanofibers while also providing a significant increase in yield and ease of production. To improve and enhance the Forcespinning™ production method, a 2D computational Forcespinning™ fluid dynamics model is developed. Three computer models, namely time-independent and time-dependent inviscid models and a viscous model are obtained and the influences of various parameters on Forcespinning™ fiber formation are obtained. This work also presents a detailed explanation …

Development Of A Ripple Rejection Controller For Dc Commutated Motors, Spencer M. Atkin

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

The requirement of modern systems to be quiet and run smoothly increases production costs. The manufacture and purchase of high quality motors that meet these demands becomes increasingly costly. By using the ever increasing computer power available in micro-controllers, at the same costs, it is possible to use current sensing to develop control adjustments which decrease power ripples caused by the commutators of basic DC commutated motors. These ripples if left unmitigated propagate through to torque ripples which then increase the acoustic noise level present.

Remanufacturing Cleaning Process Evaluation, Comparison And Planning, Ozan Yagar

Theses and Dissertations - UTB/UTPA

This thesis aims to combine previous research on remanufacturing cleaning processes and applications into a single decision-making tool, in the form of software, which a remanufacturer can use to find a cleaning system that matches their specific demands. This thesis will provide an in-depth review of each cleaning process, the chemicals used in those processes, and the contamination types for which they were developed. This research also provides evaluation and comparison that assists remanufacturers in designing their cleaning systems. Finally, there will be a description and demonstration of the software. The ultimate goal is to find correct cleaning process to …

Electromagnetic Interference Shielding Effectiveness Of Metallic Thin Films Deposited On High Density Polyethylene And Styrene Butadiene Copolymer Reinforced With Carbon Nanofibers, Horus Garcia

Theses and Dissertations - UTB/UTPA

Aluminum, Copper and Silver were deposited by thermal evaporation onto Vapor Grown Carbon Nanofiber (VGCNF) reinforced High Density Polyethylene (HDPE) and Styrene Butadiene Copolymer (SBC) composites. Electromagnetic Interference Shielding Effectiveness (EMI SE) was conducted on the structures to analyze the synergistic effect. Characterization was performed by Scanning Electron Microscopy, X-ray Diffraction, and Atomic Force Microscopy. Adhesion test and surface influence on SE were also performed. It was observed that a single layer metallic thin film on carbon nanofiber (CNF) polymer composite experienced a summation of shielding performance. The EMI SE increased with CNF content increase of 10, 15, and 20 …

Automated Resonant Wireless Power Transfer To Remote Sensors From An Unmanned Aerial Vehicle, Brent Griffin

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Wireless magnetic resonant power transfer is an emerging technology that has many advantages over other wireless power transfer methods due to its safety, lack of interference, and efficiency at medium ranges. In this thesis, we develop a wire- less magnetic resonant power transfer system that enables unmanned aerial vehicles (UAVs) to provide power to, and recharge batteries of, wireless sensors and other electronics far removed from the electric grid. We address the difficulties of implementing and outfitting this system on a UAV with limited payload capabilities and develop a controller that maximizes the received power as the UAV moves into …

Mathematical Model And Experimental Exploration Of The Nanoinjector Lance Array, Nathan C. Toone

Theses and Dissertations

The Nanoinjector Lance Array has been developed to inject foreign material into thousands of cells at once using electrophoresis to attract and repel particles to and from the electrically-charged lances. A mathematical computer model simulating the motion of attracted or repelled proteins informs the design of the nanoinjection lance array system. The model is validated by accurately predicting protein velocity in electrophoresis experiments. A complete analysis of parameters is conducted via simulations and specific research questions regarding the counter electrode of the nanoinjector lance array system are explored using the model. A novel technique for fabricating lance arrays from collapsed …

Design And Testing Of A Biological Microelectromechanical System For The Injection Of Thousands Of Cells Simultaneously, Gregory Herlin Teichert

Theses and Dissertations

The ability to inject DNA and other foreign particles into cells, both germ cells (e.g. to produce transgenic animals) and somatic cells (e.g. for gene therapy), is a powerful tool in genetic research. Nanoinjection is a method of DNA delivery that combines mechanical and electrical methods. It has proven to have higher cell viability than traditional microinjection, resulting in higher integration per injected embryo. The nanoinjection process can be performed on thousands of cells simultaneously using an array of microneedles that is inserted into a monolayer of cells. This thesis describes the needle array design requirements and the fabrication process …

Flame Synthesis Of Iron Oxide Nanowires For Direct Coal Chemical Looping Combustion, And Tungsten Oxide Nanowires For Enhanced Photoelectrochemical Water Splitting, Pratap Rao

Link Foundation Energy Fellowship Reports

The applications of metal oxide NWs are limited because conventional synthesis methods cannot achieve the scalable, rapid, controllable and economical synthesis of high-quality metal oxide NWs. In the present work, two novel methods for the flame synthesis of metal oxide NWs are developed, and the resulting nanowires tested for two promising, emerging energy conversion technologies: 1) Direct Coal Chemical Looping Combustion, and 2) Photoelectrochemical watersplitting. These synthesis methods are rapid, atmospheric, controllable and scalable, result in highly pure and crystalline materials, and could greatly extend the applicability of metal oxide nanowires to largescale energy conversion and storage problems.

The Biomechanical Implications Of An Intrinsic Decompressive Pre-Load On A Posterior Dynamic Stabilization System, Jeffrey Ellis Harris

Theses and Dissertations

The purpose of this research was to investigate the influence of applying an intrinsic decompressive pre-load to a particular dynamic stabilization device on the biomechanical response of the lumbar spine. The FlexSPAR, which supports this ability, was used as a test case. A finite element model of a full lumbar spine was developed and validated against experimental data, and tested in the primary modes of spinal motion. The model was used to compare five lumbar spine test cases: healthy, degenerate, implanted with a pre-loaded device, implanted with a device without a pre-load, and implanted with rigid fixators. Results indicated that …

Phase-Resolved Characterization Of Conical Turbulent Premixed Flames: An Investigation Of Forced Blowoff Dynamics, Sayan Biswas

Master's Theses

Flame dynamics of a bluff body stabilized turbulent premixed flame as it approaches lean blowoff is of interest for practical applications. It is also important to understand the flame behavior under harmonic flow perturbations as it may occur due to acoustically unstable operation of compact combustors. In this study, a harmonically excited conical flame was studied to determine its behavior under strong burning and near blowoff conditions. Chemiluminescence imaging was employed using a Photron high speed camera to characterize the phase resolved flame characteristics for a range of excitation frequencies from 50 to 400 Hz in confined and unconfined geometries. …

Design, Analysis And Testing Of Haptic Feedback System For Laparoscopic Graspers In In Vivo Surgical Robots, Nikhil Salvi

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Laparo-Endoscopic Single Site (LESS) Robotics Surgery is an advanced technology in the field of Minimally Invasive Surgery (MIS). The LESS surgical robots significantly improve the surgeon’s accuracy, dexterity and visualization, and reduce the invasiveness of surgical procedure results in faster recovery time and improved cosmetic results. In a standard robotic endosurgery, the palpation of tissues is performed by laparoscopic graspers located at the end effectors. The master-slave configuration in robotic surgery leads in remote access to the operation site. Therefore, surgeon’s ability to perceive valuable sensory information is severely diminished. Sensory information such as haptics, which is essential for safe …

Characterization Of Ba1-X-YCaXSrYTio3 Perovskites As Pb-Free Dielectric Materials, Lingling Zhang, Siwei Wang, Xusheng Wang, Kevin Huang

Faculty Publications

Use of lead-containing piezoelectric components in electrical and electronic devices has been banned on the EU market since July 1st, 2006. Development of lead-free high performance piezoelectric materials to meet the strong market demand is therefore imperative. In this paper, we report a systematic study on the structural, dielectric and ferroelectric properties of one class of lead-free piezoelectric materials, Ba_1-x-yCa_xSr_yTiO₃ (x = 0-0.4, and y = 0-0.2) ceramics, using techniques such as XRD, SEM, impedance analyzer, and ferroelectric analyzer. It is found that with increasing Sr concentration in Ba …

Data Consistency And Conflict Avoidance In A Multi-User Cax Environment, Robert Aaron Moncur

Theses and Dissertations

This research presents a new method to preserve data consistency in a multi-user CAx environment. The new method includes three types of constraints which work by constraining and controlling both features and users across an entire multi-user CAx platform. The first type of constraint includes locking or reserving features to enable only one user at a time to edit a given feature. The second type of constraint, collaborative feature constraints, allows flexible constraining of each individual feature in a model, and the data that defines it. The third type of constraint, collaborative user constraints, allows the constraining of user permissions …

High-Throughput Rear-Surface Drilling Of Microchannels In Glass Based On Electron Dynamics Control Using Femtosecond Pulse Trains, Lan Jiang, Pengjun Liu, Xueliang Yan, Ni Leng, Chuancai Xu, Hai Xiao, Yongfeng Lu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This study proposes a rear-surface ablation enhancement approach to fabricate high-aspect-ratio microchannels by temporally shaping femtosecond laser pulse trains. in the case study of K9 glass, enhancements of up to a 56 times higher material removal rate and a three times greater maximum drilling depth are obtained by the proposed method, as compared with conventional femtosecond laser drilling at the same processing parameters. the improvements are due to the changes of photon-electron interactions by shaping femtosecond pulse train, which can effectively adjust the photon absorption and localized transient material properties by changing electron dynamics such as free electron densities. © …

Performance Comparisons Of Personal And Professional-Grade 3d Printers, Alfonso Fernandez, Ryan Wicker, Francisco R. Medina, David Espalin

COURI Symposium Abstracts, Summer 2012

The recent emergence of personal 3D printers (i.e., systems that cost $5,000 or less) has engaged a new class of users including hobbyists, tinkerers, entrepreneurs, and do-it-yourselfers. Over 20,000 personal 3D printers were sold in 2011, and thus there is a need for users to understand the cost and performance of personal 3D printers as compared to low-cost professional-grade machines (i.e., systems that cost between $5,000 and $20,000). The cost, process time, material usage, and dimensional accuracy was assessed for select personal 3D printers and low-cost professional-grade systems. The study showed that the laminated object manufacturing (LOM) printer generated 80% …

A Comparative Study Of Strength And Stiffness Of Thin-Walled Specimens Fabricated By Fdm And 3d Printing Technologies, Miranda Rodrigo

Theses and Dissertations

Rapid Prototyped part failure constitutes a major issue for both RP providers and customers. When parts fail the reputation of the vendor is heavily deteriorated, customer dissatisfaction increase and replacement of the broken parts is often necessary to avoid the loss of future business. Product design teams often run into situations where Rapid Prototyped parts are not able to withstand shipping and handling and delivered broken or while demonstrating and examining the parts. When done in the face of customers this builds a perception of poor quality and lack of aptitude on the design group as well as the RP …

Sic-Cnt Multifunctional Nanocomposites For High Temperature Structural, Thermoelectric And Sensing Applications, Salvador Sandoval, Luz I. Bugarin, Luz I, Arifur Chowdhury, Luisa A. Cabrera, Mujibur R. Khan

COURI Symposium Abstracts, Summer 2012

The purpose of this project is to study the thermal-electrical and mechanical properties of the Nanojunctions between Single-Wall Carbon Nanotubes (SWCNT) and Silicon Carbide (SiC). The mixture was done by spreading the nanoparticles in a solution of ethanol and SiC, then sintered to a solid sample of 10 mm x 10 mm x 35 mm, which was attached with Alumel (Ni-Al) wire using silver epoxy to form a circuit for recording during fracture testing. The carbon nanotubes used were approximately 60% semiconducting and 40% metallic. The themal-electrical effect changed when SWCNTs (at 2, and 5 wt%) were infused into SiC. …

Nanowire-Graphene Hybrids For Li-Ion Insertion, Philip A. Morton, Mohammad Arif I. Shuvo, Yirong Lin

COURI Symposium Abstracts, Summer 2012

Lithium ion batteries are one of the most popular energy storage devices due to its high energy density. However, their performance is hindered by the limited surface area of the anode. This research focuses on the use of graphene nanowire hybrids and their performance as anode material. These hybrid structures have a greater surface area then graphite, the most common anode material. Greater surface area will enhance lithium ion insertion, and thus improve battery performance. The graphene oxide (GO) will be synthesized using the Hummer’s plus method. The GO will be sonicated and reduced in an argon furnace to form …

Research And Development Of An Extremely Affordable Prosthetic Knee, Victor H. Duenas, Noe Vargas-Hernandez

COURI Symposium Abstracts, Summer 2012

The objective of this research and development work is to apply the design process in a prosthetic knee mechanism. The importance of human knee is founded in the provided mobility, body positioning and support of the body weight. But for amputees, limitations for everyday tasks imply a real challenge. The project scope a cycle involving the social need, the development and the supply of the solution layout. The motivation is to improve life quality through voluntary and independent human movement by providing a low cost knee design.

The design process requires the conceptual, embodiment, detail and evaluation phases to complete …

Research And Development Of An Expert System In Idea Generation Methods To Aid In The Engineering Design Process, Rodrigo Enriquez, Noe Vargas-Hernandez

COURI Symposium Abstracts, Summer 2012

The objective of this research is to develop an Expert System (i.e. software) to aid designers in selecting appropriate idea generation methods for their specific design situation. This expert system would help designers generate creative ideas more frequently, and hence better designs and better products for society. The first step is to understand the creative design process in detail; this involves the engineering design process, cognitive processes, and other related elements. This understanding is represented initially as a conceptual model. Following an Artificial Intelligence (AI) approach, this model is then developed into a Logical model that defines entities, attributes, and …

Order-Disorder Transition Of Aragonite Nanoparticles In Nacre, Zaiwang Huang, Xiaodong Li

Faculty Publications

Understanding nacre’s bottom-up biomineralization mechanism, particularly, how individual aragonite platelets are formed, has long remained elusive due to its crystallographic peculiarity and structural complexity. Here we report that crystallographic order-disorder transition can be triggered within individual aragonite platelets in pristine nacre by means of heat treatment and/or inelastic deformation, offering a unique opportunity to discriminate mysterious aragonite nanoparticles in transmission electron microscopy. Our findings unambiguously uncover why aragonite nanoparticles in pristine nacre have long been inaccessible under TEM observation, which is attributed to the monocrystal-polycrystal duality of the aragonite platelet. The underlying physical mechanism for why an individual aragonite platelet …

Toward A Gpu-Accelerated Immersed Boundary Method For Wind Forecasting Over Complex Terrain, Rey Deleon, Kyle Felzien, Inanc Senocak

Mechanical and Biomedical Engineering Faculty Publications and Presentations

A short-term wind power forecasting capability can be a valuable tool in the renewable energy industry to address load-balancing issues that arise from intermittent wind fields. Although numerical weather prediction models have been used to forecast winds, their applicability to micro-scale atmospheric boundary layer flows and ability to predict wind speeds at turbine hub height with a desired accuracy is not clear. To address this issue, we develop a multi-GPU parallel flow solver to forecast winds over complex terrain at the micro-scale, where computational domain size can range from meters to several kilometers. In the solver, we adopt the immersed …

Analytical Thermal Model Of Friction Stir Welding With Spatially Distributed Heat Source, Gordon Scott Reese

Theses and Dissertations

Friction stir welding (FSW) has been studied extensively for the past two decades. Thermal modeling has been of particular interest, as the quality of the weld is dependent upon the temperature history of the work piece during the process. Since direct temperature measurements of the welded zone are not possible, an analytical model was developed to predict the temperature in this area. This model requires parameters that cannot be easily experimentally determined, so a best fit for these parameters was acquired via regression analysis by comparing the model to experimental data acquired outside of the weld zone. The model was …

Measurement And Analysis Of Gas Composition In A Staged And Unstaged Oxy-Fired Pulverized Coal Reactor With Warm Flue Gas Recycle, Skyler Charles Chamberlain

Theses and Dissertations

Nearly half of the electrical power produced in the United States is generated with coal. Coal power is inexpensive and reliable, but coal combustion releases harmful pollutants including NOx and SOx into the atmosphere if not controlled. CO2, a greenhouse gas, is also released during coal combustion and may contribute to global warming. A promising technology enabling carbon capture is oxy-coal combustion. During oxy-combustion, coal is burned in an atmosphere of O2 and recycled flue gas to eliminate nitrogen which makes up the majority of air-combustion flue gas. Oxy-combustion flue gas is mainly composed of CO2 and H2O. H2O can …