The Effects Of Physical Activity On Greenhouse Gas Emissions For Common Transport Modes In European Countries, Aidan Duffy, Robert Crawford

Articles

This paper applies a life cycle methodology to estimate activity-related contributions of transport modes to GHG emissions. The methodology uses national input-output tables, environmental accounts, household budget data and nutritional data to derive food-sector GHG coefficients of consumption for ten European countries. The food energy requirements for each mode of transport are estimated taking account of the modal activity level and energy requirements. Walking, cycling, driving and bus travel are considered. Typical national food energy-related emissions for walking, cycling, and driving ranged from 25.6 - 77.3 gCO2-eq/pass.km, 10.4 - 31.4 gCO2-eq/pass.km and 1.7 - 5.2 gCO2-eq/pass.km; passenger transport was found …

Evaluation And Design Of Potting Production Process Improvements For The Non-Profit Organization, Growing Grounds Farm, Maiya Avalon Bourland, Precilla Tang

Industrial and Manufacturing Engineering

This report focuses on the potting production process for the non-profit organization (NPO) Growing Grounds Farm (GGF), and aims to promote a standardized workflow system to enhance the working experience for Transitions‐Mental Health Association employees and volunteers. This project takes careful consideration into the process improvements proposed so to support the double bottom line of economic and social objectives. To address the equally important objectives, the Human Centered Design toolkit created by IDEO, specifically for third sector organizations, was integrated with the traditional Industrial Engineering design process methodology. Feasible alternatives were developed and evaluated based on the objectives. The selected …

Design Of An Automated Employee Scheduling System, Matthew Cameron, Yuriy Goldman

Industrial and Manufacturing Engineering

Many retail stores, as well as other organizations that employ a multitude of part-time employees, rely on developing schedules frequently, since the availabilities of the employees as well as the needs of the business change often. This process is often performed on a weekly basis, and is complex and time-consuming. The schedule must typically satisfy numerous requirements, including business needs, legal restrictions, and employee availability constraints. As a result, errors are common, and employee time that could have been spent on improving sales or operations is instead consumed by the scheduling task.

This project explores two solution methods for this …

Atk's Radial Airframe Forming Process Assessment, Andres Martinez

Industrial and Manufacturing Engineering

The purpose of this project was to provide ATK with a solution to increase efficiency in the R-02 radial forming center so that it could meet the increase in demand projected for the next 5 years. In addition, give ATK projected dates of when new machines would need to be implemented to be able to keep up with the demand. The system was analyzed through time studies to identify areas of possible improvement and eliminate any non-value added activities. Cycle times of each activity were used to simulate the current state of the system using ProModel software. Changes in operations …

Restaurant Design: An Industrial Engineering Perspective, Joseph Travis Spanu

Industrial and Manufacturing Engineering

The objective of this paper is to design a health food restaurant using current industrial engineering tools and practices. This includes creating a menu, determining the average gross profit per customer, determining the location, designing a 3-d layout, simulating service, and analyzing local food supply chains. Using a simplified menu and pricing quotes from a food distributor, the average gross profit per customer is estimated to be $3.50. Location is determined by comparing the predicted number of customers and the cost to rent at two different areas. A downtown location is determined to gross approximately $5,200 per month over a …

Relationships Between Unoccupied Classroom Acoustical Conditions And Elementary Student Achievement Measured In Eastern Nebraska, Lauren M. Ronsse, Lily M. Wang

Durham School of Architectural Engineering and Construction: Faculty Publications

Building standards recommend maximum background noise levels (BNL) and reverberation times (RT) for unoccupied classrooms. However, existing research does not show a consistent correlation between these parameters and student achievement. Through in situ testing, this research seeks to determine what acoustical conditions should be attained in elementary schools for students to meet educational goals. Acoustical measurements were conducted in a Nebraska public school system and correlated to achievement scores from students in the surveyed classrooms. Unoccupied BNLs and RTs were gathered in 34 third and 33 fifth-grade classrooms. Additionally, binaural room impulse response measurements were gathered in a subset of …

Novel Approach To Junctional Bleeding: Tourniquet Device Proposal For Battlefield Hemorrhage Control, Kyle W. Cabaniss

Master's Theses

This study investigated possible solutions to the current wartime problem of junctional hemorrhaging, or massive traumatic hemorrhaging in non-tourinquetable areas such as the neck, groin, or armpit. Junctional hemorrhaging has been identified as a major contributor to potentially survivable deaths seen on the battlefield today and therefore is a priority for the U.S. armed and coalition forces (Kragh et al., 2011a; Bozeman, 2011). Common tourniquets today are standard issue and carried by soldiers in the military, but are limited to distal extremity trauma. As the battlefield has changes however, trauma has transformed from commonly seen gunshot wounds to more extreme …

Women's High Heel Discomfort Analysis And Prototype Solution, Kevin Blakley, Annamarie Kepple

Industrial and Manufacturing Engineering

ABSTRACT

WOMEN’S HIGH HEEL DISCOMFORT ANALYSIS AND SOLUTION

Kevin Blakley and Annamarie Kepple

Women love high heeled shoes, but this love comes at the cost of comfort. Wearing high heels causes a lot of pain and, in the long term, health complications. This project tries to overcome the problem by ultimately making high heels more comfortable. In order to do this, one must first understand the reasons that high heels are uncomfortable, such as arch angle, heel height, and the changes in walking motion. Once there is a true understanding of the factors that contribute to high heel discomfort, the …

Film Cooling In Fuel Rich Environments, Jacob J. Robertson

Theses and Dissertations

The ultra compact combustor is a high performance gas turbine design concept that portends reduced weight for future weapons platforms. A natural outcome of the design is the continual presence of fuel-rich air in the turbine component of the engine. Because modern cooling schemes for hot section turbine blades involve injecting cool, oxygen-rich air adjacent to the surface, the potential arises for reaction with the unconsumed radicals in the mainstream ow and augmented heat transfer to the blade. This outcome is contrary to the purpose of film cooling, and can lead to early life-cycle turbine failure. This study examined the …

Design And Testing Of An H2/O2 Predetonator For A Simulated Rotating Detonation Engine Channel, Stephen J. Miller

Theses and Dissertations

A study is presented on the relationship between a pre-detonator and a detonation channel of an RDE. Testing was conducted on a straight narrow channel made of clear polycarbonate windows connected to an H₂/O₂ pre-detonator to simulate the RDE initiation scheme and allow for flow visualization. A comparison is made on decoupling distance and wave velocities for a range of pre-detonator designs, inclination angles, equivalence ratios and geometries placed within the simulated channel. Regardless of inclination angle or equivalence ratio the detonation wave decoupled within 25 mm from the pre-detonator exit into the channel. A step change …

In Situ Analysis Of Fatigue Crack Propagation In Polymer Foams, Elio E. Saenza, Leif A. Carlsson, Anette M. Karlsson

Mechanical Engineering Faculty Publications

This paper presents an in situ SEM experimental study on cyclic crack propagation in closed-cell polymer foams. The microscopic failure mechanisms in precracked PVC and PES specimens of 60 and 90 kg/m³ densities were examined under low-cycle fatigue loading. In the PVC foam, crack propagation occurred incrementally by successive failure of cell boundaries in front of the crack tip. The crack occasionally jumped to cell boundaries above or below the main crack resulting in non-self similar growth. Crack propagation in the PES foam occurred incrementally by extensive plastic tearing and subsequent tensile failure of the cell edge in front …

Design And Optimization Of A Keycard Encoding Machine, Elliott Oberg

Biomedical Engineering

Security on college campuses is a good thing, especially when it comes to your dorm room or apartment building. But due to high initial cost, the Housing and Business Department at Cal Poly, San Luis Obispo, has opted for a proprietary door lock system which requires encoding new keycards manually for every resident, every year. The goal of this project is to offset this labor cost and drain on resources by automating the keycard encoding process. This project will address the design specifications and economic advantages of automation while also exploring and comparing alternative solutions.

2013 (Spring) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the spring of 2013.

Me-Em Enewsbrief, March 2013, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Kase, The Laptop Cooling Case, Jana Morrison, Tyler Ries

Biomedical Engineering

This report describes the final design and analysis of a laptop cooling case as a marketable product for a group of entrepreneurial marketing student based out of California Polytechnic State University San Luis Obispo. Background market research and empirical measurements were taken in order to confirm that this would be a marketable product worth designing. Then previous solutions were researched in order to identity weaknesses and strengths. After rigorous research, it was determined that a passive cooling system, in which channels directed airflow to the computer fan would be the best system in terms of functionality, performance, and cost. A …

Numerical Investigation Of Plasma Actuator Configurations For Flow Separation Control At Multiple Angles Of Attack, Thomas Kelsey Iv, West, Serhat Hosder

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Quantifying The Nonlinear, Anisotropic Material Response Of Spinal Ligaments, Daniel J. Robertson

Theses and Dissertations

Spinal ligaments may be a significant source of chronic back pain, yet they are often disregarded by the clinical community due to a lack of information with regards to their material response, and innervation characteristics. The purpose of this dissertation was to characterize the material response of spinal ligaments and to review their innervation characteristics.


Review of relevant literature revealed that all of the major spinal ligaments are innervated. They cause painful sensations when irritated and provide reflexive control of the deep spinal musculature. As such, including the neurologic implications of iatrogenic ligament damage in the evaluation of surgical procedures …

Investigations Of Attitudes Towards Offshore Wind Farm Development In Ireland: Their Implication Towards Future Development Of The Industry., Aidan Melia

Purdue Polytechnic Masters Theses

This current research investigates what the attitudes of Irish people are towards the development of offshore wind farms in Ireland. Using a qualitative approach, a questionnaire is carefully designed and distributed among a sample population from three coastal communities. One is located on the west coast and two on the east coast. The two locations on the east coast have an involvement in offshore wind farms. One of the locations plays host to Ireland’s only offshore wind farm, while there are plans in place for an offshore wind farm at the other location. The results from the questionnaires are analyzed …

Analysis Of Hers Index Scores For Recent Versions Of The International Energy Conservation Code (Iecc) [Revised], Florida Solar Energy Center, Philip W. Fairey

FSEC Energy Research Center®

The EnergyGauge HERS software tool was used to examine the IECC Standard Reference Design (IECC SRD) configuration for one-story 2000 ft2 and two-story 2,400 ft2 single-family homes in sixteen representative U.S. cities. IECC SRD homes were configured for the 2006 IECC, the 2009 IECC and the 2012 IECC. Two additional set of analysis were conducted, both using the 2012 IECC SRD with enhanced equipment: 1) with equipment configured to meet the 2015 National Appliance Energy Conservation Act (NAECA) equipment requirements and 2) with equipment that is on the cusp of significant market penetration with efficiencies greater than the 2015 standard.HERS …

Criteria For The Initiation Of Modes Of Response Of A Caisson Subjected To A Breaking Wave Force, Jaw Guei Lin, Chi Chao David Tung

Journal of Marine Science and Technology–Taiwan

This paper concerns problems of a caisson subjected to a breaking wave force: (1) what are the possible modes of response and (2) the conditions initiate into these modes. These two questions have not been studied. The objective of this paper is to answer these two questions. However, the actual response of a caisson that takes place in each mode is not addressed in this study. A caisson placed on a horizontal frictional base, subjected to a concentrated horizontal force of short duration, applied to the seaward side face of the caisson and accompanied by a corresponding uplift force on …

Carbonation Service Life Prediction Of Existing Concrete Viaduct/Bridge Using Time-Dependent Reliability Analysis, Ming-Te Liang, Ran Huang, Shen-Ann Fang

Journal of Marine Science and Technology–Taiwan

This paper examines the predicted carbonation life of an existing concrete viaduct/bridge in the atmospheric environment based on probability and reliability indices. The probability is dependent upon the carbonation rate, carbonation remainder, concrete quality, and concrete cover. The carbonation life is defined as the service life of reinforced concrete (RC) or prestressed concrete (PC) structure at the beginning of time of steel corrosion when concrete cover surfers from carbonation and loses the protection function to steel. The carbonation life is equivalent to the initiation time of corrosion of reinforcement. Both the Chorng-ching viaduct and Wannfwu bridge were offered as illustrative …

Equilibrium And Nonequilibrium Molecular Dynamics Simulations Of Thermal Conductance At Solid-Gas Interfaces, Zhi Liang, William Evans, Pawel Keblinski

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Thermal Conductance at Solid-Gas Interfaces with Different Interfacial Bonding Strengths is Calculated through Green-Kubo Equilibrium Molecular Dynamics (EMD) Simulations. Due to the Finite Size of the Simulation System, the Long-Time Integral of the Time Correlation Function of Heat Power Across the Solid-Gas Interface Exhibits an Exponential Decay, Which Contains the Information on Interfacial Thermal Conductance. If an Adsorbed Gas Layer is Formed on the Solid Surface, It is Found that the Solid-Gas Interface Needs to Be Defined at a Plane Outside the Adsorbed Layer So as to Obtain the Correct Result from the Green-Kubo Formula. the EMD Simulation Result …

Material Characterization And The Effects Of Moisture And Drying On Injection Molded Torlon 5030, Michael R. Di Re

Master's Theses

The effects of water absorption and drying were studied on injection molded Torlon 5030, a high performance thermoplastic fabricated by Solvay Specialty Polymers. Torlon 5030 contains 30% by weight glass fibers in a polyamide-imide base resin. The objective behind this work was to test and better define relevant properties for industrial applications using this material. While the material design guide offers information on many mechanical properties including tensile, fatigue, and creep data; there is little to no publicly published data on the effects of water absorption and any subsequent drying of Torlon 5030. Blistering was also studied. With exposure to …

Environmental And Energy Saving Technologies Of Vinyl Chloride Production, Mykola Kurta

USF Tampa Graduate Theses and Dissertations

Recently, because of the increase of environmental concerns in process design, the need to enhance conversion to product and prevent generation of wasteful byproducts in the reactor network has become urgent. This prevents high cost treatment and separation costs downstream in the process. Therefore, in this thesis I focus on making production of vinyl chloride monomer (VCM) more efficient and on possible ways of industrial organochlorine waste (OCW) recycling. In particular, in the first experiment, we investigate how catalyst and its structure can affect product output.

Infrared spectroscopy and X-ray diffraction analysis were utilized to investigate the structure of the …

Short-Term Test Results: Transitional Housing Energy Efficiency Retrofit In The Hot-Humid Climate, Florida Solar Energy Center, Karen Sutherland

FSEC Energy Research Center®

This project evaluates the renovation of a 5,800-ft², multiuse facility located in St. Petersburg, on the west coast of central Florida, in the hot-humid climate. An optimal package of retrofit measures was designed to deliver 30%-40% annual energy cost savings for this building with annual utility bills exceeding $16,000 and high base load consumption. Researchers projected energy cost savings for potential retrofit measures based on pre-retrofit findings and disaggregated, weather-normalized utility data. A cost-benefit analysis was conducted for the seven retrofit measures implemented; adding attic insulation and sealing soffits, tinting windows, improving whole-building airtightness, upgrading heating and cooling …

Improvement Of Heat Transfer Efficiency At Solid-Gas Interfaces By Self-Assembled Monolayers, Zhi Liang, William Evans, Tapan Desai, Pawel Keblinski

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using Molecular Dynamics Simulations, We Demonstrate that the Efficiency of Heat Exchange between a Solid and a Gas Can Be Maximized by Functionalizing Solid Surface with Organic Self-Assembled Monolayers (SAMs). We Observe that for Bare Metal Surfaces, the Thermal Accommodation Coefficient (TAC) Strongly Depends on the Solid-Gas Interaction Strength. for Metal Surfaces Modified with Organic SAMs, the TAC is Close to its Theoretical Maximum and is Essentially Independent from the SAM-Gas Interaction Strength. the Analysis of the Simulation Results Indicates that Softer and Lighter SAMs, Compared to the Bare Metal Surfaces, Are Responsible for the Greatly Enhanced TAC. © 2013 …

Single Network Adaptive Critics Networks-Development, Analysis, And Applications, Jie Ding, Ali Heydari, S. N. Balakrishnan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Solving infinite time optimal control problems in an approximate dynamic programing framework with two-network structure has become popular in recent years. In this chapter, an alternative to the two-network structure is provided. We develop single network adaptive critics (SNAC) which eliminate the need to have a separate action network to output control. Two versions of SNAC are presented. The first version, called SNAC outputs the costates and the second version called J-SNAC outputs the cost function values. Special structure called Finite-SNAC to efficiently solve finite time problems is also presented. Illustrative infinite time and finite time problems are considered; numerical …

Vector Acoustic Intensity Around A Tuning Fork, Daniel A. Russell, Justin Junell, Daniel O. Ludwigsen

Physics Publications

The acoustic intensity vector field around a tuning fork is investigated. Theory for a longitudinal quadrupole source predicts a well-defined transition between near-field and far-field, with significant circulation of sound energy in the near-field. Vector components of the time-averaged intensity were measured using a two-microphone intensity probe and found to agree well with predictions from theory. The vector intensity map is interpreted, and shown to provide useful information about the near-field of an acoustic source.

Measured Cooling Performance And Potential For Buried Duct Condensation In A 1991 Central Florida Retrofit Home, Florida Solar Energy Center, Dave Chasar

FSEC Energy Research Center®

The Florida Solar Energy Center (FSEC) conducted energy performance monitoring of two existing residences in Central Florida that were undergoing various retrofits. These homes were occupied by FSEC researchers and were fully instrumented to yield detailed energy, temperature, and humidity measurements. The data gave feedback about the performance of two levels of retrofit in two types of homes in a hot-humid climate. This report covers a moderate-level retrofit and includes 2 years of pre-retrofit data to characterize the impact of improvements. The other home, covered in a separate report (Parker and Sherwin 2012), is a deep energy retrofit that has …

Electrospun Polymeric Membranes For Adhesion, Johnny F. Najem, Shing Chung Josh Wong, Guang Ji

Mechanical Engineering Faculty Research

With growing interest in detachable adhesives, new materials are explored such as the types that employ elastomers, thermoplastics, and pressuresensitive polymers [1]. Generally, these adhesives produce substantial shear adhesion strengths but are considerably difficult to detach from surfaces. Commercial high strength adhesives make use of chemical interactions such as glues and permanently attach two surfaces. Subsequently, fabrication of dry adhesives with anisotropic force distributions has the potential in several applications such as tapes, fasteners, treads of wall-climbing robots, spiderman's suits, microelectronics, medical and space applications. High aspect ratio (AR) structures exhibit significant shear adhesion strength compared to ones with low …