Mechanical Engineering Commons^™

Propagation Of Sound In The Vicinity Of Rigid Porous Interfaces, Hongdan Tao

Open Access Dissertations

Propagation of sound in the vicinity of rigid porous interfaces is investigated systematically to facilitate the acoustical characterization of sound absorption materials for noise reduction applications. Various rigid porous interfaces are considered: (1) a semi-infinite porous layer; (2) a porous hard-backed surface; and (3) a porous impedance-backed layer. A closed-form solution and numerical methods are derived with respect to each rigid porous interface condition.

A modified saddle-point method is exploited to investigate the sound field emanating from a monopole source above and below a rigid porous interface. The solutions can be expressed in a form that resembles the classical Weyl-Van …

Mechanisms Of Microstructure Formation Under The Influence Of Ultrasonic Vibrations, Milan Rakita

Open Access Dissertations

Positive effects of ultrasound on crystallization have been known for almost 90 years. Application of ultrasound has been very successful in many industries, most notably in chemistry, creating a new branch of science - sonochemistry. However, ultrasonication has not found wide commercial application in the solidification processing. The reason for that is the complexity of underlying phenomena and the lack of predicting models which correlate processing parameters with the properties of a product. The purpose of this study is to give some contribution toward better understanding of mechanisms that lead to changes in the solidifying microstructure. It has been found …

An Experimental Investigation Of Wind Turbine Aerodynamic Interaction, Brandon Lee Ennis

Open Access Dissertations

Wind turbines have become a viable component in the overall energy makeup of the United States due to improved economics where energy prices have risen and production costs dropped. For a fixed cost, the effectiveness of a wind turbine financially is highly related to its performance. Considering the size of current wind farms, a minor performance improvement will result in large additional sums of revenue. A problem that has received attention with wind farms is that while the fixed costs of the development do get spread out further to reduce the installed cost of each wind turbine, the wind turbines …

Electric Machine Differential For Vehicle Traction Control And Stability Control, Sandun Shivantha Kuruppu

Open Access Dissertations

Evolving requirements in energy efficiency and tightening regulations for reliable electric drivetrains drive the advancement of the hybrid electric (HEV) and full electric vehicle (EV) technology. Different configurations of EV and HEV architectures are evaluated for their performance. The future technology is trending towards utilizing distinctive properties in electric machines to not only to improve efficiency but also to realize advanced road adhesion controls and vehicle stability controls. Electric machine differential (EMD) is such a concept under current investigation for applications in the near future. Reliability of a power train is critical. Therefore, sophisticated fault detection schemes are essential in …

Near-Field Pressure Distributions To Enhance Sound Transmission Into Multi-Layer Materials, Andrew Martin Jessop

Open Access Dissertations

The large impedance difference between air and most solids prevents significant energy transfer from incident acoustic waves across the air-material interface. Refraction also plays a role in preventing acoustic transmission, as the wave speed difference between air and solid materials results in an increase of the resulting propagation angles, creating near-field pressure distributions in the solid material. By utilizing evanescent pressure distributions, which decay normal to the usual direction of propagation and are represented as plane waves propagating with complex angles, energy propagation through the interface can be increased in the subsonic region of wave propagation: i.e., where waves typically …

Hybrid And Smart Topologically Interlocking Materials, Somesh Khandelwal

Open Access Dissertations

This thesis explores the mechanical properties of a new class of multifunctional architectured materials, Topologically Interlocking Materials (TIMs). These materials are created as an assembly of unit elements arranged in an interlocking pattern such that the load transfer between unit elements occurs by contact only. In the absence of adhesive interaction, the tensile component of the load is carried by complementary tensile elements in the form of external constraints or integrated filaments. By virtue of the bottom up design used in creating these materials, their mechanical properties are influenced by a number of controllable parameters including shape, confinement force, scale, …

Multiscale Simulation Of Thermocline Energy Storage For Concentrating Solar Power, Scott Michael Flueckiger

Open Access Dissertations

Concentrating solar power (CSP) is a renewable and demonstrated technology for large-scale power generation but requires multiple engineering advancements to achieve grid parity with conventional fossil fuels. Part of this advancement includes novel and inexpensive thermal energy systems to decouple daily power production from intermittent solar collection. Dual-media thermocline tanks, composed of molten salt and solid rock filler, offer low-cost storage capability but the concept has experienced limited deployment in CSP plants due to unresolved concerns about long-term thermal and structural stability. The main objective of the present work is to advance the understanding of thermocline storage design and operation …

Graphene Decorated Substrates And Their Interfacial Characteristics, Anurag Kumar

Open Access Dissertations

Carbon nanotubes and graphene have been extensively studied for their excellent properties. As research on carbon expands, two major issues face the scientific community: (i) Expanding the scale of synthesis and (ii) Integration of different carbon structures for improved functionality. While significant advancements have been made in large-scale synthesis, room for improvement remains. As the scale of production increases, issues such as time, cost and energy that may otherwise not be very significant, begin to play greater roles. Thus, in order to effectively transition from laboratory prototypes to industrial products, a synthesis method that can address these issues is strongly …

Subgrid Scale Modeling For Large Eddy Simulation Of Buoyant Turbulent Flows, Niranjan Shrinivas Ghaisas

Open Access Dissertations

Buoyancy effects due to small density differences commonly exist in turbulent fluid flows occurring in nature and in engineering applications. The large eddy simulation (LES) technique, which is being increasingly used for simulating buoyant turbulent flows, requires accurate modeling of the subgrid sclae (SGS) momentum and buoyancy fluxes. This thesis presents a series of LES and direct numerical simulation (DNS) studies towards a priori and a posteriori evaluation of existing SGS models, and development of new SGS models for the buoyancy flux. This thesis also presents the application of LES, in elucidating qualitative physical features and accurate measures of important …

Solution To Certain Problems In The Failure Of Composite Structures, Jonathan Goodsell

Open Access Dissertations

The present work contains the solution of two problems in composite structures. In the first, an approximate elasticity solution for prediction of the displacement, stress and strain fields within the m-layer, symmetric and balanced angle-ply composite laminate of finite-width subjected anticlastic bending deformation is developed. The solution is shown to recover classical laminated plate theory predictions at interior regions of the laminate and thereby illustrates the boundary layer character of this interlaminar phenomenon. The results exhibit the anticipated response in congruence with the solutions for uniform axial extension and uniform temperature change, where divergence of the interlaminar shearing stress is …

Numerical Techniques For The Noninvasive Assessment Of Material Properties And Stresses In Soft Biomaterials, Kent David Butz

Open Access Dissertations

The noninvasive measurement of finite displacements and strains in biomaterials by magnetic resonance imaging (MRI) may be shown to enable mathematical estimates of stress distributions and material properties within structures of the body such as articular cartilage or the intervertebral disc. Such methods will allow for non-contact and patient-specific modeling in a manner not currently possible with traditional mechanical testing or finite element techniques. Therefore, the objective of this thesis was to develop computational methods incorporating imaging-based measures of deformation, composition, and local microstructure to permit nondestructive analysis of a range of complex biomechanical systems.

Finite strain-based models were developed …

A Novel Multiblock Immersed Boundary Method Enabling High Order Large Eddy Simulation Of Pathological And Medical Device Hemodynamics, Anupindi Kameswararao

Open Access Dissertations

Computational fluid dynamics (CFD) simulations are becoming a reliable tool in understanding disease progression, investigating blood flow patterns and evaluating medical device performance such as stent grafts and mechanical heart valves. Previous studies indicate the presence of highly disturbed, transitional and mildly turbulent flow in healthy and pathological arteries. Accurate simulation of the transitional flow requires high order numerics together with a scale resolving turbulence model such as large eddy simulation (LES). This in turn limits one to use a structured fluid flow solver on which complex, branching arterial domains that are typical in the human blood circulatory system could …

On The Uniqueness And Sensitivity Of Indentation Testing Of Isotropic Materials, J. K. Phadikar, T. A. Bogetti, Anette M. Karlsson

Mechanical Engineering Faculty Publications

Instrumented indentation is a popular technique to extract the material properties of small scale structures. The uniqueness and sensitivity to experimental errors determine the practical usefulness of such experiments. Here, a method to identify test techniques that minimizes sensitivity to experimental erros is in indentation experiments developed. The methods are based on considering “shape functions,” which are sets of functions that describe the force–displacement relationship obtained during the indentation test. The concept of condition number is used to investigate the relative reliability of various possible dual indentation techniques. Interestingly, it was found that many dual indentation techniques can be as …

Theory Of Constraints Project Management In A Manufacturing Environment, Shihching Kraft

Mechanical & Aerospace Engineering Theses & Dissertations

The following thesis covers the concepts of Theory of Constraints (TOC) Project Management. Introduced by Eliyahu M. Goldratt in I 984, TOC is a management philosophy that focuses on the use of critical chain project management to prioritize everyday tasks in a company. In TOC Project Management, there is always at least one resource constraint that limits the speed at which projects are completed. TOC management philosophy also recognizes that most projects in the manufacturing industry face unknown schedule delays that could cause projects to be completed late or over the planned budget. During project plan creation, plans are developed …

Design And Implementation Of Software For Technological Forecasting And Modeling Technological Obsolescence, Gershom Kwaku Obeng

Mechanical & Aerospace Engineering Theses & Dissertations

In a world that is highly infused with technology, it is important that an organization knows how many resources such as manpower, equipment, and funding are needed at what time so that the organization does not suffer unnecessary risks. It is also important to know when to replace equipment. After examining different methods of forecasting, it was determined that manipulation of growth curves was the best way to determine the likelihood of device failure at a specific time. An approach in engineering economics was used to estimate the cost due to the failure of various devices or groups of devices. …

Probabilistic Modeling Of Erroneous Human Response To In-Vehicle Route Guidance Systems: A Domain Decomposition-Based Algorithm, Abdullah Al Farooq

Computational Modeling & Simulation Engineering Theses & Dissertations

Drivers are generally assumed to follow the shortest route to their destinations prescribed by in-vehicle route navigation systems without mistake. However, it is not uncommon that drivers make mistakes when there are complex intersections along the route to miss turns. Such mistakes would result in following a longer route than the optimal one. In this thesis, research has been conducted to analyze the effects of the number of intersections in the shortest routes of different O-D (origin-destination) pairs. While different formulations can be employed to describe such "driving with error" model, a Domain Decomposition (DD) partitioning algorithm has been developed …

Effects Of Bit Type On Maximum Torque And Axial Force Using Manual Screwdrivers, Mark Hickok

Master's Theses (2009 -)

The screwdriver is a tool that has been among the most widely used hand tools for decades and continues to be used in the workplace to perform a variety of fastening tasks. Advancements in fastener technology have been complemented by the development of new types of screwdriver bits. While designs may vary, so do the force application requirements placed on the tool user. The primary objective of this experiment is to analyze the relationship between user torque and screwdriver bit design. A further objective is to utilize the results to develop an effort metric by which bits of different designs …

An Investigation Of Phase-Change Effects During Rapid Compression Machine Experiments, Colin Banyon

Master's Theses (2009 -)

Rapid compression machines (RCMs) are well characterized laboratory scale devices capable of achieving internal combustion (IC) engine relevant thermodynamic environments. These machines are often used to collect ignition delay times as targets for gas-phase chemical kinetic fuel autoigntion models. Modern RCMs utilize creviced piston(s) to improve charge homogeneity and allow for an adequate validation of detailed chemistry mechanisms against experiments using computationally efficient, homogeneous reactor models (HRMs). Conventionally, experiments are preformed by introducing a premixed gas of fuel + oxidizer + diluent into the machine, which is compressed volumetrically via a piston. Experiments investigating low-vapor pressure fuels (e.g. diesels, biodiesels, …

Micro-Scale Dielectric Spectroscopy Of Biological Cells, Arindam Ghosh

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years microfluidics has become one of the most commonly used tools to investigate cellular biology and to provide a platform for novel biomedical devices. Electrical Impedance Spectroscopy (EIS) was formulated as a non-invasive and label-fi.ee method to investigate the dielectric and the structural properties of materials. Since the early 20th century, EIS and Dielectric Spectroscopy have been applied to measure the dielectric properties of biological cells and tissues. Information about the cell membrane, cytoplasm and the nucleus can be extracted by dielectric spectroscopy. This thesis focuses on the applicability of the analytical models, in particular the Maxwell-Wagner Interfacial …

Theoretical Analysis Of Torsionally Vibrating Microcantilevers For Chemical Sensor Applications In Viscous Liquids, Tao Cai

Dissertations (1934 -)

Dynamically driven microcantilevers excited in the transverse (or out-of-plane) direction are widely used as highly sensitive chemical sensing platforms in various applications. While these devices work very well in air, their performance in liquids is not efficient because of the combination of increased viscous damping and effective fluid mass. In order to improve the characteristics of microcantilevers in liquid environments, some other vibration modes such as the torsional mode and lateral (or in-plane) flexural mode have been proposed.
In this work, the characteristics of torsionally vibrating rectangular microcantilevers with length L, width b and thickness h in viscous liquids are …

Sequential Structural And Fluid Dynamics Analysis Of Balloon-Expandable Coronary Stents., David Martin

Doctoral

As in-stent restenosis following coronary stent deployment has been strongly linked with stent-induced arterial injury and altered vessel hemodynamics, the sequential numerical analysis of the mechanical and hemodynamic impact of stent deployment within a coronary artery is likely to provide an excellent indication of coronary stent performance. Despite this observation, very few numerical studies have considered both the mechanical and hemodynamic impact of stent deployment. In light of this observation, the aim of this research is to develop a robust numerical methodology for investigating the performance of balloon-expandable coronary stents in terms of their mechanical and hemodynamic impact within a …

Application Of Machine Learning And Parametric Nurbs Geometry To Mode Shape Identification, Robert Mceuen Porter

Theses and Dissertations

In any design, the dynamic characteristics of a part are dependent on its geometric and material properties. Identifying vibrational mode shapes within an iterative design process becomes difficult and time consuming due to frequently changing part definition. Although research has been done to improve the process, visual inspection of analysis results is still the current means of identifying each vibrational mode determined by a modal analysis. This research investigates the automation of the mode shape identification process through the use of parametric geometry and machine learning.In the developed method, displacement results from finite element modal analysis are used to create …

Numerical Simulation Model On Irreversibility Of Shock-Wave Process, Longhao Huang

Master's Theses (2009 -)

The objective of this research is to develop a better understanding of the irreversibilities associated with the shock compaction of matter, especially as a result of impact. Due to complex shock processes, experimentation alone cannot fix the material state, since properties such as internal energy, entropy as well as the shock process are not measurable. Thus, in addition to experimentation, analytical and numerical methods are also used to completely characterize the shock process, although they are restricted by underlying constitutive assumptions. Instead of using artificial irreversibility, such as artificial viscosity to simplify and stabilize the numeric shock model, this work …

Admittance Selection For Force Guided Assembly With Optimal Motion, Fernando Rodriguez Anton

Master's Theses (2009 -)

t

Current robots lack the precise relative positioning necessary to complete automatic assembly tasks. Several solutions have been proposed. Some approaches use complex vision and force sensing systems to generate corrective motion if misalignment is present in the assembly task. Other solutions rely on generating elastic behavior, known as compliance, between the end eector and the held movable part. This compliant mechanism helps guide the movable part of the assembly into its proper position. The project focuses on designing a process by which passive compliant systems can achieve successful assembly for a range of misalignment and generate error-reducing motion that …

A New Angle On Microscopic Suspension Feeders Near Boundaries, Rachel E. Pepper, Marcus Roper, Sangjin Ryu, Nobuyoshi Matsumoto, Moeto Nagai, Howard A. Stone

Department of Mechanical and Materials Engineering: Faculty Publications

Microscopic sessile suspension feeders are a critical component in aquatic ecosystems, acting as an intermediate trophic stage between bacteria and higher eukaryotic taxa. Because they live attached to boundaries, it has long been thought that recirculation of the feeding currents produced by sessile suspension feeders inhibits their ability to access fresh fluid. However, previous models for the feeding flows of these organisms assume that they feed by pushing fluid perpendicular to surfaces they live upon, whereas we observe that sessile suspension feeders often feed at an angle to these boundaries. Using experiments and calculations, we show that living suspension feeders …

Development Of An Experimental Testbed For Research In Lithium-Ion Battery Management Systems, Nima Lotfi, Poria Fajri, Samuel Novosad, Jack Savage, Robert G. Landers, Mehdi Ferdowsi

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Advanced electrochemical batteries are becoming an integral part of a wide range of applications from household and commercial to smart grid, transportation, and aerospace applications. Among different battery technologies, lithium-ion (Li-ion) batteries are growing more and more popular due to their high energy density, high galvanic potential, low self-discharge, low weight, and the fact that they have almost no memory effect. However, one of the main obstacles facing the widespread commercialization of Li-ion batteries is the design of reliable battery management systems (BMSs). An efficient BMS ensures electrical safety during operation, while increasing battery lifetime, capacity and thermal stability. Despite …

Visual Literacy And The Integration Of Parametric Modeling In The Problem-Based Curriculum, Matthew Benedict Assenmacher

Master's Theses and Doctoral Dissertations

This quasi-experimental study investigated the application of visual literacy skills in the form of parametric modeling software in relation to traditional forms of sketching. The study included two groups of high school technical design students. The control and experimental groups involved in the study consisted of two randomly selected groups of students. The participants were exposed to eight weeks of technical drawing and parametric modeling instruction prior to the start of the study.

The potential applications of emerging technologies for the purpose of integrating visual literacy into the curriculum are not fully understood. Society is moving towards a more immediate …

Dimensionless Criteria For Selecting Tidally-Influenced Advective-Dispersive Desalination Brine Mixing Plume Characterization Models, Alireza Shahvari

Civil & Environmental Engineering Theses & Dissertations

The very nature of requirements for implementing a desalination process is highly spatial due to the need to secure both a source for the operation and sink for brine dilution. Thus, the applicable coastal location is bound to natural tidal mixing characteristics and subjected to a near- or a far-field availability for source and sink. Mixing characteristics of coastal waters are very different from one point to another due to the spatiotemporal tidal characteristic in loco in a manner that it can vary from being highly advective to completely dispersive dominant. Once a location is identified, estimation of corresponding water …

Design Exploration And Analysis Of Carbon-Infiltrated Carbon Nanotube Vascular Stents, Darrell John Skousen

Theses and Dissertations

The purpose of this research was to design, develop, and test coronary stent designs composed of carbon-infiltrated carbon nanotubes (CI-CNTs). Coronary stents currently have two major complications: restenosis and thrombosis. CI-CNT stents have potential to address both of these issues, and therefore may provide improved clinical outcomes. CI-CNT stent geometry is patterned using high-resolution photolithography that provide advantages in design possibilities.To develop a coronary stent, a standard design process was followed including: background, design specifications, concept generation, development, analysis, and testing. Background research was first completed and general design specifications for coronary stent performance were compiled. Multiple design concepts were …

Energy And Economic Optimization To Achieve Near Zero Energy Homes In Europe: Implications Of Inclusion Of Lighting And Appliances, Florida Solar Energy Center, Danny Parker

FSEC Energy Research Center®

Achieving annual net zero energy use in homes has been demonstrated as feasible in dozens of monitored projects in the United States.[1] In particular, very low energy use homes in Europe have been proven within the Passivhaus approach.[2] Achieving 'nearly zero energy buildings' (NZEB) has also been established as a vital objective over the next decade within the European Union (EU) (Boermans et al., 2011). However, reaching this result at the lowest possible cost remains a key challenge around the world. Balancing renewable power generation with energy efficiency will be vital in Europe as anticipated by Voss, Musall and Lichtmeß.[4] …