Mechanical Engineering Commons^™

Experimental Investigation Of Methane Reformer With A Continuous Flow Reactor, Xiao Zhang

Mechanical and Aerospace Engineering Dissertations - Archive

Over the decades, seeking for an alternative energy source has been more and more significant because of increasing demand with rapid industry expansion. Liquid hydrocarbon from Fischer-Tropsch process is considered as an alternative fuel source because the product is considered as subtle for petroleum-derived. Syngas as feedstock for F-T process plays a crucial role in liquid hydrocarbon production. Among several commercial and experiment technologies, the most common technology for syngas production is natural gas reforming. The product from reforming process has proper carbon monoxide/hydrogen ratio for direct application in F-T synthesis. Meanwhile, combined carbon dioxide into reforming reaction has attracted …

Complex Multidisciplinary Systems Decomposition For Aerospace Vehicle Conceptual Design And Technology Acquisition, Amen Omoragbon

Mechanical and Aerospace Engineering Dissertations - Archive

Although, the Aerospace and Defense (A&D) industry is a significant contributor to the United States’ economy, national prestige and national security, it experiences significant cost and schedule overruns. This problem is related to the differences between technology acquisition assessments and aerospace vehicle conceptual design. Acquisition assessments evaluate broad sets of alternatives with mostly qualitative techniques, while conceptual design tools evaluate narrow set of alternatives with multidisciplinary tools. In order for these two fields to communicate effectively, a common platform for both concerns is desired. This research is an original contribution to a three-part solution to this problem. It discusses the …

The Effects Of Temperature And Relative Humidity On Exposure Of Legacy And Future Technology Hardware, Under Real Data Center Conditions In An Ansi/Isa Classified G2 Environment, Oluwaseun Michael Awe

Mechanical and Aerospace Engineering Dissertations - Archive

It is well established that it is safe to operate information technology (IT) equipment in a G1 classified contaminant severity level when operating within specified ASHRAE recommended and allowable limits in an air-side economizer data center. This is basis for which electronic equipment manufacturers provide warranty for their products. IT equipment manufacturers in the US now requires data centers operators to demonstrate that they meet all the specified conditions consistently before fulfilling warranty equipment failure. This places limitation to where data center utilizing air-side economizer can be located. In order to determine the reliability of electronic hardware in higher severity …

Analysis Of Composite Beams With Airfoil Cross-Sections With I-Section Stiffener Under Tension And Bi-Directional Moments, Peter Louis Leboulluec

Mechanical and Aerospace Engineering Dissertations - Archive

Annual wind power generation capacity in the US has increased from 3 gigawatts in 2000 to 61 gigawatts in 2013 and is on track to fulfill 20% of projected U.S. electricity needs (305 gigawatts) by 2030. To enable the increase in electricity generation of wind turbines, longer blades are being designed which require improved engineered blades to handle higher loads. Thus, the wind turbine industry is turning to the use of carbon-epoxy composite materials to take advantage of their low weight yet high strength ratio and improved fatigue resistance. Current analyses to design turbine blades utilize either Finite Element Analysis …

Thermal Energy Storage For Expanded Use Of Data Center Indirect/Direct Evaporative Cooling, Jefferey Luttrell

Mechanical and Aerospace Engineering Dissertations - Archive

Computer cooling system design evolved over time with goals of increasing efficiency and decreasing cost. Early computers were essentially hand-built and very expensive. Reliable operation required aggressive cooling to maintain acceptable component temperatures and this was achieved with relatively low ventilation air temperatures. With time, the scale of operations increased to the point that operating cost began to strongly influence design decisions. Computer room air conditioners consumed substantial amounts of electrical power, in some situations almost as much power as the computer equipment. One cost saving idea used outside air when the ambient temperature fell below the normal cooling supply …

Understanding The Alchemilla Leaf And Its Hydrophobicity, Atul Mohandas Kootathil

Mechanical and Aerospace Engineering Theses - Archive

The Alchemilla leaf has been well known and studied frequently for its hydrophobic ability. However, much difficulty has been met in replicating its microstructure for hydrophobic applications. Also, not much experimental data was found on the behavior of leaf’s microstructure. Gathering information from experimental results may provide new understanding of its wetting properties before attempting to mimetic its wetting behavior. In this research, the focus is to detail the observed solid-water-air interaction on Alchemilla leaf by simulating condensation, evaporation and rainfall conditions, which are the common ways that a plant may interact with water drops in nature. Documenting these observations …

Attitude Stabilization Of Spacecraft Using Moving Masses, Juran Hwang

Mechanical and Aerospace Engineering Theses - Archive

This research investigates the ability of stabilizing spacecraft rotational motion by internal mass actuation. The mass actuation mechanism consists of three internal masses placed along the three axes at some offset distance that can move to induce inertial forces and moments and change the inertia matrix and center of mass. A set of nonlinear equations of motion are developed to model the motion, both orbital and rotational dynamics and kinematics, of a spacecraft with mass and inertial variation due to internal mass actuation, under the gravitational field of Earth. The equations inherently include the inertia effect of the mass motion …

Developing And Validating Energy Models For Indirect And Direct Evaporative Cooling Used In Datacenters, Rajesh Kasukurthy

Mechanical and Aerospace Engineering Theses - Archive

In the present day to day life, Internet of things is everything, i.e., we need internet and telecommunication for almost every task of our life and these require data from data centers. These data centers provide various facilities like data processing, storage, and transmission, and maintenance, operations etc., for performing these tasks, a huge amount of power is consumed by the data center, which in turn generates large amount of heat. As these data centers are to be made operational throughout the year, cooling of data centers is of utmost importance. These cooling systems like air conditioners, economizers and evaporative …

Mechanical Property Evaluation Of Magnesium Rich Primer Coating System Over Aa 2024 T-3 Aluminum Alloy By Nano-Inedntation, Hongyi Qu

Mechanical and Aerospace Engineering Theses - Archive

Aluminum alloy is widely used as a major structural material, such as for wing and fuselage, in aerospace industry. Corrosion is the most insidious form of damage to aluminum alloy, which can cause aircraft structure damage and related safety issue. Coating is generally used in industry to protect metal structure. An alternative to present toxic chromium primer coating system, magnesium rich primer (MgRP) has been developed to protect AA 2024 T-3. Studies have demonstrated the anti-corrosion performance of MgRP. However, the interlayer material heterogeneity can affect the mechanical properties of coating such as modulus, hardness and interfacial behavior. In the …

Active Torque Vectoring For All Wheel Drive Fsae Electric Car, Vikas Tukaram T Pawar

Mechanical and Aerospace Engineering Theses - Archive

UTA Racing is known for building well-engineered FSAE racecars. This year team is building, its first electric car by using AWD in-wheel motor concept car E-16. All wheel drive electric vehicles has an ability to apply instantaneous torque to all four wheels permit increased car performance. An ‘Active Model Based Torque Vectoring System controller’ is designed to realize this objective. The controller was designed to replicate three electronically controlled LSD's on an all-wheel drive platform with different control strategies. This was achieved based on the principal of distributing total driver requested torque between wheels, equivalent to the percentage of the …

Guidance Navigation And Control Implementation For Unmanned Ground Vehicle Using Ni-Myrio, Ishwarya Srinivasan

Mechanical and Aerospace Engineering Theses - Archive

This research effort aims at investigating alternative real-time implementation software and hardware for Guidance, Navigation and Control (GNC) algorithms for an Unmanned Ground Vehicle (UGV). A GNC algorithm was previously developed for a skid-steered tracked UGV to go through assigned waypoints based on encoder counts. The UGV has two electric motors driving the tracks on each side and two encoders providing the speeds of the drive wheels. This algorithm was implemented using Matlab/Simulink-based model running on a mini computer, interfacing with the electric motors and encoders through a specialty control board. This current effort is to implement the same GNC …

Fitting B-Splines Curves To Coarse Data Cloud Using Modified Squared Distance Minimization Method, Vinay Vivek Mhala

Mechanical and Aerospace Engineering Theses - Archive

Additive manufacturing has made us realize that we can fabricate complex shapes that were difficult to manufacture with subtractive processes. Topology optimizations results have complex shapes and have rough surfaces which are difficult to manufacture even by additive manufacturing. To automate the process of converting rough surfaces into smooth surfaces for the benefit of manufacturability would be very desirable. Computing curve segments to approximate point cloud data that represents rough surfaces and then lofting it to have a smooth surface seems to be a promising methodology to achieve automation. We implement B-spline formulation along with Pottmann’s iterative method based on …

Study Of Crack Propagation Under Thermal Loading On A 3d Tsv Package, Subramanian R. Gowtham

Mechanical and Aerospace Engineering Theses - Archive

Today, there is a revolution in going for miniaturization in size of electronic packages. More thinner, lighter and complex packages are in use for almost every electronic device. This initiation was taken to the next level and gives us a whole new ideology called 3D packaging. Currently, 3D packaging is the on-going research in almost all the electronic packaging related industries. 3D package uses Through Silicon Via (TSV) technology that gained momentum in the development and helped packaging system for significant miniaturization and power reduction, which result in increased performance. However, the reliability assessment is needed to evaluate the critical …

Embedding Antenna Shear/Pressure Sensors In Prosthetic Liner Material, Shahanavaz Eilbeigi

Mechanical and Aerospace Engineering Theses - Archive

Published surveys indicated that 40-60% of prosthesis users experience discomfort and skin problems. These studies highlighted the needs for enhanced prosthetic performance and fit. It is extremely difficult to address these problems due to two reasons: first, ambulation create varying areas of shear and pressure on the residual limb, but it is not clear which shear/pressure combinations are acceptable and what is the safe stress level for users. In addition, the volume of the residual limb changes throughout the day and activity level. Therefore, there is a strong need to develop a light, thin, flexible, and wirelessly interrogated sensor for …

Microfluidic Platform For Impedance Characterization Of Endothelial Cells Under Fluid Shear Stress., Vanessa Velasco

Electronic Theses and Dissertations

Endothelium dysfunction has been associated with many pathophysiological processes leading to cardiovascular diseases. Studying endothelium behavior is vital to understand the onset, prevention, and treatment of such diseases. Electrical impedance spectroscopy has been shown to provide a real-time in vitro evaluation of cell behavior including cell monolayer permeability. However, the majority of published work has been primarily with static cell culture models or macro-scale models that do not properly represent the physiological sizes, structures, and environmental conditions of human blood vessels. Within this dissertation, the design, fabrication, characterization, and application of a microfluidic impedance platform is presented for the in …

Fundamental Principles Of Tremor Propagation In The Upper Limb, Andrew Doran Davidson

Theses and Dissertations

Although tremor is the most common movement disorder, there exist few effective tremor-suppressing devices, in part because the characteristics of tremor throughout the upper limb are unknown. To clarify, optimally suppressing tremor requires a knowledge of the mechanical origin, propagation, and distribution of tremor throughout the upper limb. Here we present the first systematic investigation of how tremor propagates between the shoulder, elbow, forearm, and wrist. We simulated tremor propagation using a linear, time-invariant, lumped-parameter musculoskeletal model relating joint torques and the resulting joint displacements. The model focused on the seven main degrees of freedom (DOF) from the shoulder to …

Control-Oriented Modeling, Validation, And Analysis Of A Natural Gas Engine Architecture, Chaitanya Panuganti

Open Access Theses

In order to improve performance and meet increasingly tight emissions regulations, engine manufacturers must improve algorithms used to control the engine. One possible strategy is to utilize centralized control algorithms that take into account the coupled interactions between inputs and outputs. Implementing a centralized control strategy often requires some kind of dynamic model of the system, which is a primary motivation for modeling efforts in this thesis. In a methodical fashion, this thesis derives a control model for a natural gas engine architecture and validates this control model against reference data in simulation. Additionally, this thesis performs control-oriented analysis on …

Analysis Of Feedback Control Applied With Command Shaping To Minimize Residual Vibration, Nicholas L. Jacobs

Open Access Theses

Joint flexibility is a physical trait that affects all robotic systems to some degree. This characteristic has been shown to be very detrimental to the performance of these robotic systems when implementing fast point-to-point motion. During such motion, the robot will induce vibrations in its structure that will extend past the completion of the move. Many techniques have been applied over the years in order to minimize these residual vibrations. One such method is known as command shaping, which will construct the input profile so as to avoid exciting the natural frequencies of the system. This work seeks to extend …

Phase Field Damage Simulations Of Debonding Between Matrix And Spherical Inclusions, Johanna B. Palsdottir

Open Access Theses

Polymer-bonded explosives (PBX) are complicated composites, and it is important for practical applications to know how they deform and fracture. PBX consists of large volume fraction of energetic particles and experiments show that the interface is a critical region for structural stability since particles are often weakly bonded to the polymer and cracks initiate there and the composite fractures. This study focuses on the interface between a particle and a binder and how the particle inclusion starts to debond from the polymer binder in compressive and tensile loading.

A phase field damage model is used to model the response of …

Cyclic Tensile Response Of A Polyurethane Material, Yizhou Nie

Open Access Theses

Polyurethane is one of the most widely used polymer materials in the world. With the increasing demand of polyurethane, its mechanical behaviors are particularly of interest. In particular, the response of the material under a quasi-static loading being subject to an impact load. To delineate the effect of rate change on the mechanical response of polyurethane, a tensile experiment was designed where the specimen is initially subjected to quasi-static tensile loading and then to high-rate cyclic tension within the same experiment. Constant strain-rate experiments at both quasi-static and high strain rates are also conducted. The analysis of the results leads …

Advanced Hydraulic Systems For Next Generation Of Skid Steer Loaders, Mrudula Uday Orpe

Open Access Theses

Fluid power systems have been extensively used in off highway applications like skid steer loaders, wheel loaders, excavators since many years. Work has been done by both industry and academia to improve efficiency, reduce noise and leakages in these systems. With increasing competition in the market, importance is now also given to operator comfort and machine productivity in off highway applications.

Mobile, off – highway vehicles like Skid-steer loaders are widely used in labour saving applications like loading earth into a truck, dig and move material on construction sites to, clean roads, clear snow from roads etc. To carry out …

High-Throughput Mechanical Characterization Methods For Composite Electrodes And In-Situ Analysis Of Li-Ion Batteries, Luize Scalco De Vasconcelos

Open Access Theses

Electrodes in commercial rechargeable batteries are microscopically heterogeneous materials. The constituents often have large variation in their mechanical properties, making the characterization process a challenging task. In addition, the mechanical properties and mechanical behaviors of electrodes are closely coupled with the electrochemical processes of lithium insertion and extraction. There is an urgent need to develop an experimental platform to characterize the chemomechanical response of electrodes under the in-situ conditions of charge and discharge.

In the first part of this thesis, instrumented grid indentation is employed to determine the elastic modulus and hardness of the constituent phases of a composite cathode. …

Test Cell Set-Up To Enable Drive-Cycle Testing Of A Variable Valve Actuation Enabled Camless Diesel Engine, Alexander Harrison Taylor

Open Access Theses

The previous facility which was used for engine testing at Purdue's Ray W. Herrick Laboratories utilized an eddy current dynamometer which is only suited for steady-state testing and throttle snaps. To better utilize a pre-existing camless diesel engine, which is is enabled via variable valve actuation, it was desired to perform transient drive-cycle tests. To accomplish this goal, a variable frequency drive AC dynamometer was required. Given that a brand new facility was constructed, the team was presented with an opportunity for ground up design of a test cell.

The new test cell's operation was proved out using a cammed …

Experimental Characterization Of Scroll Expander For Small-Scale Power Generation In An Organic Rankine Cycle, Felipe Airoldi Accorsi

Open Access Theses

Organic Rankine Cycles (ORC) are thermodynamic power cycles designed to generate work from low temperature sources. The low temperature heat input, typically between 80 °C to 270 °C, allows them to recover energy from industrial waste heat, exhaust gas from diesel, engines, solar systems, geothermal systems, and others. This technology already is commercialized in large-to-medium-scale power plants; however, it is still in development for small-to-micro scale.

The operating principle of ORC comprises four major steps. First, the working fluid evaporates at high pressure using the heat transfer from the low temperature heat source. Then, the working fluid reduces its enthalpy …

Algorithms For Lidar Based Traffic Tracking: Development And Demonstration, Vamsi K. Bandaru

Open Access Theses

The current state of the art of traffic tracking is based on the use of video, and requires extensive manual intervention for it to work, including hours of painstaking human examination of videos frame by frame which also make the acquisition of data extremely expensive. Fundamentally, this is because we do not have observability of the actual scene from a camera which captures a 2D projection of the 3D world. Even if video were to be automated, it would involve such algorithms as RANSACK for outlier elimination while matching features across frames or across multiple cameras. This results in algorithms …

Design And Analysis Of A High Performance Valve, Jordan M. Garrity

Open Access Theses

Most valves available in the fluid power industry today are capable of achieving either a large flow rate or a quick response time; however, often they are unable to deliver both simultaneously. Commercially available valves that can produce both at the same time require complex geometries with multiple actuation stages and piloting pressures, making them expensive components. To establish their active usage in applications across the fluid power industry, a reduction in price for these components is paramount. The Energy Coupling Actuated Valve (ECAV) is capable of solving the large flow rates with fast actuation speeds trade-off by utilizing a …

Modelling And Control Of A Parallel Through-The-Road Plug-In Hybrid Vehicle, Rohinish Gupta

Open Access Theses

With an increasing number of passenger vehicles, automotive emissions has become a major challenge. Among other pollutants, green house gas (GHG) emissions form a majority of the exhaust coming out of the tail-pipe and are blamed for the rising temperature of the earth. The net carbon emissions due to running a lightduty passenger vehicle are studied in the present thesis. Hybrid electric vehicles have been proven to have lower green house gas emissions than conventional vehicles as electricity is cleaner than fossil fuels.

Using a parallel-through-the-road hybrid architecture vehicle, different power management strategies are studied. To begin with, a detailed …

A Novel Mode-Switching Hydraulic Hybrid For An On-Highway Vehicle: A Study Of Architecture And Control, Hiral Jayantilal Haria

Open Access Theses

Increasing demand for fossil fuels, their limited reserves and the environmental effects resulting from the transportation sector has raised severe concerns to government agencies, transportation industry as well as the end-users. This has raised interests in improving the fuel economy of road vehicles. One of the promising technologies in this regard is hybridization of vehicle transmission. Hydraulic hybrids have progressively gained acceptance due to their high power density and low component costs relative to their electric counterpart.

Many different hydraulic hybrid architectures have been developed to achieve better power management and regenerative braking and have been tested for performance and …

The Effect Of Static And Dynamic Aging On Fatigue Behavior Of Sn3.0ag0.5cu Solder Alloy, Yiran Li

Open Access Theses

In microelectronic assemblies, solder joints serve as interconnection between different packaging levels and are an important cause for the failure of microelectronic products. Sn-Ag-Cu solder alloys became important after lead-based solder alloys were caused to be discarded by regulations in European Union and Japan. However, the constitutive behavior of Sn-Ag-Cu alloys is not as well understood as lead-based solder alloys, and many studies confirm the aging of these alloys with time. The aging of Sn-Ag-Cu alloys and its effect on mechanical behavior challenges the reliability prediction of microelectronic assemblies. In this study, the effect of pretest isothermal aging and in-test …

Parametric And Design Analysis On Thermoelectric Generators, Shouyuan Huang

Open Access Theses

In facing the limited energy source reserves and environmental problems, thermoelectric generators (TEGs) are one of the promising waste heat recovery systems. The modern TEGs for exhaust stream (e.g. from automobiles) can improve the fuel economy by around 5%, taking advantage of the recent developed thermoelectric (TE) materials.

In this work, we aimed at designing a TEG as an add-on module for a gas-phase heat exchanger with maximized power output, and without negative impact (e.g. maintaining a minimum heat dissipation rate from the hot side). We first developed a parametric optimization algorithm using response surface method (RSM) and genetic algorithm …