Mechanical Engineering Commons^™

Analytical Study Of Miniature Thermoelectric Device, Mohammed Dhannoon

Masters Theses

Miniature thermoelectric devices (TE) have been regarded as hopeful devices to attain efficient cooling in microprocessors and other small-scale devices. To recognize the performances of miniature thermoelectric coolers, a thermoelectric cooling module is theoretically analyzed. Particular attention is paid to the impact of the thermoelectric element length effect and the substrate material type influence on the cooling performance. The electrical contact resistance and thermal contact are taken into account.

Furthermore, miniature thermoelectric is compared with large thermoelectric, and effective material properties of miniature thermoelectric are studied. The obtained results also demonstrate power density (cooling/heating power per unit area of the …

Optimization Methodology For Cvt Ratio Scheduling With Consideration Of Both Engine And Cvt Efficiency, Steven Beuerle

Masters Theses

A transmission ratio schedule is developed to optimize the fuel consumption for an automotive continuously variable transmission (CVT) connected to an internal combustion engine (ICE). Although the optimal operating line (OOL) generated from an engine brake specific fuel consumption (BSFC) map can be used to generate a CVT ratio schedule that yields maximum engine efficiency, it was found that OOL-based CVT ratio scheduling does not necessarily offer the best fuel economy because optimal CVT efficiency does not always correspond to OOL tracking. To develop a CVT ratio schedule that can offer the best fuel economy, a novel ratio-scheduling methodology is …

Direct Quadrature Method Of Moments With Delumping For Modeling Multicomponent Droplet Vaporization, Simcha L. Singer

Mechanical Engineering Faculty Research and Publications

A multicomponent droplet vaporization model which combines the computational efficiency of continuous thermodynamic approaches with the detailed species information provided by discrete component models has been developed. The Direct Quadrature Method of Moments (DQMoM) is used to efficiently solve for the evolution of the nodes and weights of the equivalent liquid-phase mole fraction distribution without assuming any functional form. The novelty of the approach is an inexpensive delumping procedure that is used to reconstruct the time-dependent mole fractions and fluxes for all discrete species. When applied to a vaporizing kerosene droplet, agreement between the full discrete component model, which solves …

Traction And Launch Control For A Rear-Wheel-Drive Parallel-Series Plug-In Hybrid Electric Vehicle, Adam Michael Szechy

Doctoral Dissertations and Master's Theses

Hybrid vehicles are becoming the future of automobiles leading into the all-electric generation of vehicles. Electric vehicles come with a great increase in torque at lower RPM resulting in the issue of transferring this torque to the ground effectively. In this thesis, a method is presented for limiting wheel slip and targeting the ideal slip ratio for dry asphalt and low friction surfaces at every given time step. A launch control system is developed to further reduce wheel slip on initial acceleration from standstill furthering acceleration rates to sixty miles per hour. A MATLAB Simulink model was built of the …

Investigating The Highest Melting Temperature Materials: A Laser Melting Study Of The Tac-Hfc System, Omar Cedillos-Barraza, Dario Manara, K. Boboridis, Tyson Watkins, Salvatore Grasso, Daniel D. Jayaseelan, Rudy J. M. Konings, Michael J. Reece, William E. Lee

Mechanical and Aerospace Engineering Student Publications and Presentations

TaC, HfC and their solid solutions are promising candidate materials for thermal protection structures in hypersonic vehicles because of their very high melting temperatures (>4000 K) among other properties.  The melting temperatures of slightly hypostoichiometric TaC, HfC and three solid solution compositions (Ta1−xHfxC, with x = 0.8, 0.5 and 0.2) have long been identified as the highest known. In the current  research, they were reassessed, for the first time in the last fifty years, using a laser heating technique.  They were found to melt in the range of 4041–4232 K, with HfC having the highest and TaC the lowest. …

Design Of A Rotating Brush Underwater Grooming Device With A Focus On Brush Optimization, Motor Control And Design For Reliability, Mark Harrison Nanney

Theses and Dissertations

The design and control of Remotely Operated Vehicles (ROV) to groom or clean the underwater surface of ship hulls is becoming an important aspect of the maintenance of vessels to the United States Navy. The biological growth below the waterline of the vessels can be the cause for drag penalties near 21% causing up to 32% increase in shaft power at 15 knots (Schultz, 2007). Research conducted by the Center for Corrosion and Biofouling Control at Florida Institute of Technology (FIT) indicated that weekly grooming can prevent high profile biological growth (Hearin, et al., 2015). The design of a rotating …

A Study To Develop An Electronics Chassis Compound Cylinder Pressure Vessel Using Finite Element Modeling, Gordon Randall Straley

Theses and Dissertations

This thesis develops a process to design and analyze a two-layer compound cylinder pressure vessel utilizing an inner insert to house electronic circuit card assemblies. The process begins with sizing and analysis of a compound cylinder based on analytical formulas and progresses in complexity to a 2-Dimensional plane stress finite element model of the chassis assembly and ends with a computationally expensive 3-Dimensional finite element analysis of the pressure vessel. Comparing the results from the compound cylinder to the electronics chassis, it is observed that the inner insert geometry has a strong influence on the interfacial pressure at the upper …

The Design Of An Articulating Five-Headed In-Water Grooming Tool To Maintain Ships Free Of Fouling, Caglar Erdogan

Theses and Dissertations

Biofouling is a major concern to ship owners. Biofouling increases hull roughness, increasing the frictional resistance and fuel consumption while decreasing maximum speed. Finding a way to maintain hulls free from fouling has, therefore, become a research challenge for scientists and engineers. Grooming has been proposed as a novel method for controlling fouling (Tribou and Swain 2010). It refers to the regular proactive light cleaning to maintain the hull free of fouling with minimal impact to ship coatings. The purpose of this thesis is to design, build, and deploy a compliant multiheaded grooming tool which utilized five polypropylene vertically rotating …

Numerical Study Of Erosion Of The Internal Wall Of Sales Gas Piping By Black Powder Particles, Ahmed Saud Al-Haidari

Theses and Dissertations

Micro particles, primarily from iron, can wreak havoc on a Sales Gas System. For example, the transport of particles with the gas flow can cause erosion damage to the piping system, lead to the release of toxic gasses, and interrupt the operation. The objective of the current work is to examine the erosion rate (ER) in an existing Sales Gas Piping System by simulating different black powder particles sizes and considering variable operation conditions. An elbow-shaped pipe spool is used to determine the area of maximum destruction. It will help the designer, engineer and operation personnel to predict the ER …

Development, Characterization, & Implementation Of Phase-Change Material Cold Plates For Hybrid-Electric Vehicle Battery Systems, Kevin Cwiok

Doctoral Dissertations and Master's Theses

Due to the regulations on internal combustion engine vehicles, there is a large demand of hybrid and electric vehicles with large battery packs as Energy Storage Systems (ESS) capable of long ranges and decreased emissions. These battery packs output large heat loads during charge-depletion mode and currently require active cooling to keep the batteries within operating conditions. The current systems relied onto achieve this are the air and liquid cooled thermal managements systems. A recent alternative approach to current cooling for ESS thermal management is the use of phase-change materials (PCMs). PCMs regulate the temperature of the ESS by leveraging …

Solar Car Suspension System, Alex Power, Adam O'Camb

Mechanical Engineering

No abstract provided.

Cal Poly Engineering Photobot: Final Design Review, Samantha Clements, Carlos Esquivel, Kassandra Rodriguez, Aubrey Russell

Mechanical Engineering

The purpose of this project was to create a remotely controlled camera device; the PhotoBot captures images and videos of various plants and perhaps animals for biological analysis. The features for such a device allows a user to capture images and videos from various angles and heights with minimal outside assistance. Furthermore, the device is designed for users that do not wish to spend an extensive amount of time and effort taking pictures and videos in the rainforest. The key constraints of the device includes safety, versatility, ease of use, and durability. Ultimately, this project was completed for Dr. Cris …

Implementation And Performance Evaluation Of Acoustic Denoising Algorithms For Uav, Ahmed Sony Kamal Chowdhury

UNLV Theses, Dissertations, Professional Papers, and Capstones

Unmanned Aerial Vehicles (UAVs) have become popular alternative for wildlife monitoring and border surveillance applications. Elimination of the UAV’s background noise and classifying the target audio signal effectively are still a major challenge. The main goal of this thesis is to remove UAV’s background noise by means of acoustic denoising techniques. Existing denoising algorithms, such as Adaptive Least Mean Square (LMS), Wavelet Denoising, Time-Frequency Block Thresholding, and Wiener Filter, were implemented and their performance evaluated. The denoising algorithms were evaluated for average Signal to Noise Ratio (SNR), Segmental SNR (SSNR), Log Likelihood Ratio (LLR), and Log Spectral Distance (LSD) metrics. …

Stationary Nonimaging Concentrators – A Comprehensive Study And Design Improvements, Srikanth Madala

UNLV Theses, Dissertations, Professional Papers, and Capstones

Most places on our planet receive an annual average radiation between 800-1000 W/m2. In the man-made world, this radiation is largely incident on stationary structures such as buildings, roads, monuments, bridges etc. Moreover, in the natural world also, there are large tracts of barren land which can be put to good use given their solar energy potential. The vision of the current research is to concentrate all this available solar energy to a more readily usable form. Therefore, stationary nonimaging solar concentrator technologies are sought after. This dissertation work is an exhaustive research on the nonimaging concentrating mechanisms with stationary …

Design For Manufacturability And Assembly Of An Assistive Technician Creeper, Including Single Drive Control Of A Multi-Degree Of Freedom Kinematic Mechanism, Larry T. Wilde Jr.

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

In 2011, a team of engineering students at Utah State University designed and built an assistive technician creeper to assist persons with lower-extremity physical disabilities to work in low-clearance areas. In order to put this technology on the market, a complete product redesign was needed to address safety and functionality concerns. This thesis outlines the specific design needs, presents the detailed design approach, and summarizes the final creeper solution. The mechanisms of the initial prototype were modified to independently incline or recline the upper body, and raise or lower the seat surface with a single motor. This will be especially …

Best Practices For Volume Flow Rate Measurements Using Piv At The Exit Of A Turbulent Planar Jet, Rick Cressall

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Particle image velocimetry (PIV) is used to make volume-flow-rate measurements at the exit of a turbulent, planar nozzle. The objective of this report is to assess a range of data acquisition and processing parameters. Data is acquired for volume flow rates of Reynolds numbers between 10,000 and 100,000 for both two-component (2C) and stereo PIV. The parameters are systematically changed one at a time and evaluated using differences in uncertainty, calculation time, and volume- flow-rate deviation. Data acquisition parameters follow the trends of previous work. A multitude of processing parameters were varied for several PIV processing methods. Recommendations for each …

Multivariate Calibration Of A Load Sensor For Dynamic And Static Freight Railcar Applications, Dylan Michael Blackwell

Theses and Dissertations

Determination of the load carried by each bearing in a railcar system is crucial to the integrity of the railroad industry. With accurate load measurement, the process of filling a railcar with its specified cargo can be optimized to provide the maximum amount of cargo without exceeding the upper weight limits imposed by the Associations of American Railroads (AAR). An accurate load measurement will additionally make it possible to identify any load imbalance that occurs during periods of travel which result in having a detrimental effect on the health of the bearing. Previous work conducted with a strain-gauge load sensor …

Design Of A Flexible Control Platform And Miniature In Vivo Robots For Laparo-Endoscopic Single-Site Surgeries, Lou P. Cubrich

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Minimally-invasive laparoscopic procedures have proven efficacy for a wide range of surgical procedures as well as benefits such as reducing scarring, infection, recovery time, and post-operative pain. While the procedures have many advantages, there are significant shortcomings such as limited instrument motion and reduced dexterity. In recent years, robotic surgical technology has overcome some of these limitations and has become an effective tool for many types of surgeries. These robotic platforms typically have an increased workspace, greater dexterity, improved ergonomics, and finer control than traditional laparoscopic methods. This thesis presents the designs of both a four degree-of-freedom (DOF) and 5-DOF …

Models For Decanting Gaseous Fuel Tanks: Simulations With Gfssp Thermal Model, Kailash Kumar Jain Munoth

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Transport of fuel from distillation/storage plant to different parts of the world has always been challenging task for Engineers. Different methods have been proposed over the time for transporting fuel efficiently and at low cost which include Marine vessels, Pipelines, Rail Cars and Trucks. In order to transport useful amount of fuel in a reasonably sized tank, we have to liquefy it. While few fuels are easy to liquefy there are great number of fuels which liquefy only under extreme pressure/temperature conditions. Methane has a boiling point of -161.7°C at atmospheric pressure which means it has to be cooled to …

Dynamic Responses Of Wheel-Rail Systems With Block Dampers, Tzuyu Tseng

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The wheel-rail interaction problem has been widely studied in the past few decades. In this problem, dynamic responses at the contact areas remain the central issue since they induce damage to the rail over time. In particular, the dynamic responses at the contact areas between the wheels and rails present difficulties in understanding and mathematical modeling. Even with the computer power one has today, its mathematical modeling employs the versatile numerical analysis method, the finite element method (FEM) remains a formidable challenge due to its extremely small contact areas and in turn the extremely high stress levels. In addition, friction …

Effect Of Amino-Functionalization On Insulin Delivery And Cell Viability For Two Types Of Silica Mesoporous Structures, Abdollah Zakeri Siavashani, Masoumeh Haghbin Nazarpak, Fateme Fayyazbakhsh, Tayebeh Toliyat, Steven James Peter Mcinnes, Mehran Solati-Hashjin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Inorganic Mesoporous Structures Are a Class of Novel Biomaterials that Have Shown Practical Applications in Delivery of a Variety of Therapeutic Agents. in the Present Study, Two Mesoporous Structures Were Prepared, and the Effect of Surface Modification on their Insulin Delivery and in Vitro Cytotoxicity Was Evaluated. Morphological and Structural Characterizations of Silica Particles Were Accomplished by Different Analytical Techniques, Including Scanning Electron Microscopy, X-Ray Diffraction, Fourier Transform Infrared Spectroscopy (FTIR), and Brunauer–Emmett–Teller (BET) Surface Area Analyses. the Drug Loading Capacity and in Vitro Drug Release Behavior of Silica Structures Were Investigated under Simulated Gastrointestinal Conditions and Phosphate-Buffered Saline Solution …

Flow Field Dynamics In A High-G Ultra-Compact Combustor, Andrew E. Cottle

Theses and Dissertations

The Ultra Compact Combustor (UCC) presents a novel solution to the advancement of aircraft gas turbine engine performance. A high-g UCC design operates by diverting a portion of the axial compressor flow into a circumferential combustion cavity positioned about the engine outer diameter. The circumferential cavity (CC) provides the necessary residence length and time for combustion within reduced axial lengths; furthermore, high rates of centrifugal acceleration termed high-g loading are imposed upon the swirling cavity flow. These high-g conditions are hypothesized to increase flame speed, reduce flame length, and improve lean blow-out performance. Work at AFIT was sponsored by the …

Investigating Co2 Removal By Ca- And Mg-Based Sorbents With Application To Indoor Air Treatment, Elliott T. Gall, Cem Sonat, William W. Nazaroff, Cise Unluer

Mechanical and Materials Engineering Faculty Publications and Presentations

Indoor carbon dioxide (CO 2 ) levels serve as an indicator of ventilation sufficiency in relation to metabolic effluents. Recent evidence suggests that elevated CO 2 exposure (with or without other bioeffluents) may cause adverse cognitive effects. In shelter-in-place (SIP) facilities, indoor CO 2 levels may become particularly elevated. This study evaluates four low-cost alkaline earth metal oxides and hydroxides as CO 2 sorbents for potential use in indoor air cleaning applications. Sorbents studied were MgO, Mg(OH) 2 , Ca(OH) 2 and commercially available soda lime. Uncarbonated sorbents characterized with nitrogen adsorption porosimetry showed BET surface areas in the 5.6–27 …

Effect Of Ducted Hpwh On Space-Conditioning And Water Heating Energy Use - Central Florida Lab Home, Florida Solar Energy Center, Carlos Colon

FSEC Energy Research Center®

The purpose of this research is to investigate the impact of ducted heat pump water heaters (HPWHs) on space-conditioning and water heating energy use in residential applications. Two identical HPWHs, each with a capacity of 60 gal, were tested side by side at the Flexible Residential Test Facility (FRTF) laboratories on the Florida Solar Energy Center (FSEC) campus in Cocoa, Florida. The FRTF's residential buildings feature the same square footage (1,535 ft2 ), orientation, and envelope characteristics; currently, the only difference between them is the finished floor material. The east FRTF building is furnished with standard carpet flooring, whereas the …

Focused-Based Multifractal Analysis Of The Wake In A Wind Turbine Array Utilizing Proper Orthogonal Decomposition, Naseem Ali, Hawwa Falih Kadum, Raúl Bayoán Cal

Mechanical and Materials Engineering Faculty Publications and Presentations

Hot-wire anemometry measurements have been performed in a 3×3 wind turbine array to study the multifractality of the turbulent kinetic energy dissipation. A multifractal spectrum and Hurst exponents are determined at nine locations downstream of the hub height, bottom and top tips. Higher multifractality is found at 0.5D and 1D downstream of the bottom tip and hub height. The second order of the Hurst exponent and combination factor shows the ability to predict the flow state in terms of its development. Snapshot proper orthogonal decomposition (POD) is used to identify the coherent and incoherent structures and to reconstruct the stochastic …

Determination Of Aqueous Surfactant Solution Surface Tensions With A Surface Tensiometer, Remelisa Esteves, Birce Dikici Ph.D, Matthew Lehman, Qayyum Mazumder, Nonso Onukwuba

Beyond: Undergraduate Research Journal

Surfactant solutions are applicable to engineering systems for cooling equipment for electronics. Surfactants can be added to water to improve heat transfer. An application of using aqueous surfactant solutions can be through microchannel heat sink. Although it is ideal to redesign these systems to reduce heat, it is a costly method. Surfactant solutions at optimal solution concentration can be able to transfer heat quickly and effectively with minimum expense. The surface tension of surfactant solutions is an important parameter for boiling heat transfer and must be taken into consideration. The purpose of this research is to measure surface tension of …

Determination Of Surfactant Solution Viscosities With A Rotational Viscometer, Remelisa Esteves, Nonso Onukwuba, Birce Dikici Ph.D

Beyond: Undergraduate Research Journal

Aqueous surfactant solutions are used in engineering systems for improving boiling heat transfer. The purpose of this research is to determine the viscosities of surfactant solutions and to investigate the effect of composition on viscosity. The results obtained can possibly be used as reference for further study in the effects of surfactant solution viscosities on nucleate boiling. A rotational viscometer was used to determine the viscosities of three surfactant solutions – SLS, EH-14, and SA-9 – of various compositions at room temperature. It was discovered that the viscosities of SLS, EH-14, and SA-9 had a nearly consistent pattern as their …

Extracting Vibration Characteristics Of A Guitar Using Finite Element, Modal Analysis, And Digital Image Correlation Techniques, Kiran Patil, Javad Baqersad, Daniel Ludwigsen, Yaomin Dong

Physics Publications

The sound quality generated by the guitar depends on the vibration characteristics (i.e. natural frequencies and mode shapes) of this instrument. Thus, it is of particular interest to the guitar manufacturers to be able to obtain global information about the characteristics of the guitar. Traditional sensors can only measure at discrete locations. However, digital image correlation (DIC) can measure full-field data on the surface of the structure. In the current paper, a finite element (FE) model of a guitar with free boundary configurations was developed using quadratic solid elements. An eigensolution was performed on the FE model to determine its …

Evaluating Alternative Scheduling Rules To Improve Scheduling Performance, Bryan Allan White

Theses and Dissertations

In this study a powder painting production line was examined for the purpose of improving on its scheduling. A simulation model was developed to compare the performance of alternative scheduling rules. The simulation model utilized scheduling data from the original system in order to determine how accurately it represented the original system. The model was built using the discrete event simulation software Arena. The validated model was used to test a set of scheduling rules that would change the sequence in which orders in the queue were processed. By looking at the different rules and the effects on the final …

Loss-Induced Enhanced Transmission In Anisotropic Density-Near-Zero Acoustic Metamaterials, Chen Shen, Yun Jing

Henry M. Rowan College of Engineering Departmental Research

Anisotropic density-near-zero (ADNZ) acoustic metamaterials are investigated theoretically and numerically in this paper and are shown to exhibit extraordinary transmission enhancement when material loss is induced. The enhanced transmission is due to the enhanced propagating and evanescent wave modes inside the ADNZ medium thanks to the interplay of near-zero density, material loss, and high wave impedance matching in the propagation direction. The equi-frequency contour (EFC) is used to reveal whether the propagating wave mode is allowed in ADNZ metamaterials. Numerical simulations based on plate-type acoustic metamaterials with different material losses were performed to demonstrate collimation and subwavelength imaging enabled by …