Mechanical Engineering Commons^™

Optimizing Supply Chain Collaboration Based On Agreement Buyer-Supplier Relationship With Network Design Problem, Wahyudi Sutopo, Ayu Erliza, Arien Heryansyah

Makara Journal of Technology

In recent years, the rising competitive environment with shorter product life cycles and high customization forces industries to increase their flexibility, speed up their response, and enhance concurrent engineering designs. To integrate these prospects, supply chain collaboration becomes a pertinent strategy for industries to strengthen their competitiveness. The network design problem is used to implement supply chain collaboration. In the buying and selling process, sharing information between buyer and supplier are important to obtain a transaction decision. The optimimum supply chain profit can be identified by mathematical model of network design problem. The Mathematical Model takes into consideration the uncertainity …

Effect Of Milling On The Densification Of Sic-Basedcomposites From Polysilazane, Alfian Noviyanto, Toshiyuki Nishimura

Makara Journal of Technology

High density SiC-based composites from polysilazane were fabricated by high energy milling and hot pressing. After cross-linking at 200 °C, the polysilazane was pyrolysed at 1000 °C in N2 for 2 h to form amorphous Si-C-N-O followed by high energy milling for 1 h. Milled amorphous Si-C-N-O was sintered in hot pressing at 1600 and 1700 °C for 1 h in vacuum under the applied pressure of 50 MPa. Although no sintering additives were used, dense SiC-based composites were obtained with this method. Sintered density was 3.04 g/cm3, while only 2.57 g/cm3 for amorphous Si-C-N-O without milling. It is suggested …

Characterization And Utilization Of Calcium Oxide (Cao) Thermally Decomposed From Fish Bones As A Catalyst In The Production Of Biodiesel From Waste Cooking Oil, Aldes Lesbani, Sabat Okta Ceria Sitompul, Risfidian Mohadi, Nurlisa Hidayati

Makara Journal of Technology

Thermal decomposition of fish bones to obtain calcium oxide (CaO) was conducted at various temperatures of 400, 500, 800, 900, 1000, and 1100 °C. The calcium oxide was then characterized using X-ray diffractometer, FTIR spectrophotometer, and SEM analysis. The calcium oxide obtained from the decomposition at 1000 °C was then used as a catalyst in the production of biodiesel from waste cooking oil. Diffraction pattern of the calcium oxide produced from decomposition at 1000 °C showed a pattern similar to that of the calcium oxide produced by the Joint Committee on Powder Diffraction Standard (JCDPS). The diffractions of 2q values …

Thermoeconomic Optimization Of Cascade Refrigeration System Using Mixed Carbon Dioxide And Hydrocarbons At Low Temperature Circuit, Nasruddin Nasruddin, Arnas Arnas, Ahmad Faqih, Niccolo Giannetti

Makara Journal of Technology

Many applications and industrial processes require very low cooling temperature, such as cold storage in the biomedical field, requiring temperature below -80 °C. However, single-cycle refrigeration systems can only achieve the effective cooling temperature of -40 °C and, also, the performance of the cycle will decrease drastically for cooling temperatures lower than -35°C. Currently, most of cascade refrigeration systems use refrigerants that have ozone depletion potential (ODP) and global warming potential (GWP), therefore, in this study, a cascade system is simulated using a mixture of environmentally friendly refrigerants, namely, carbon dioxide and a hydrocarbon (propane, ethane or ethylene) as the …

Developing Road Infrastructure Route Planning: Increasing Feasibility Of Toll Road Project, Mohammed Ali Berawi, Teuku Yuri Zagloel, Perdana Miraj, Abdur Rohim Boy Berawi, Wellsi Titaheluw, Saipol Bari Bin Abd Karim

Makara Journal of Technology

Indonesian government attempts to improve connectivity and to increase regional activities in Sumatera Island through the development of Trans Sumatera Toll Road (TSTR). However, despite its benefits to local economic development in Sumatera, the project shows low feasibility due to a low amount of investment. It can be attributed from the lack of planning in the initial phase to produce a comprehensive route that considers the various potentials of the regions. Thus, this research aims to investigate alternative route planning of Trans Sumatera Toll Road particularly in this paper for Central Sumatera by studying Gross Regional Domestic Product (GRDP), population …

Thermal And -Γ –Ray Irradiation Effects On The Ionic Conductivity Of (Licl)X(Montmorillonite)1-X, Safei Purnama, Aziz Khan Jahja, Takeshi Sakuma

Makara Journal of Technology

Compositesof montmorillonite (MMT) - lithium salts have been prepared using a simple process of powders mixing followed by heating. The powders resulting from this method are expected to beionic conductors with a high ionic conductivity characteristics. This characteristics is also further improved by employing gamma-ray irradiation technique at specified irradiation doses. The best results were obtained for the (LiCl)0.5(MMT)0.5 composite with a room temperature ionic conductivity of 2.192 mS/cm, which then increases to ~5 mS/cm after gamma irradiation at a dose of 400 kGy. This value is equivalent to the value of the ionic conductivity of current commercial rechargeable lithium …

Mitigation Of The Impact Of High Plug-In Electric Vehicle Penetration On Residential Distribution Grid Using Smart Charging Strategies, Chong Cao, Luting Wang, Bo Chen

Michigan Tech Publications, Part 1

Vehicle electrification presents a great opportunity to reduce transportation greenhouse gas emissions. The greater use of plug-in electric vehicles (PEVs), however, puts stress on local distribution networks. This paper presents an optimal PEV charging control method integrated with utility demand response (DR) signals to mitigate the impact of PEV charging to several aspects of a grid, including load surge, distribution accumulative voltage deviation, and transformer aging. To build a realistic PEV charging load model, the results of National Household Travel Survey (NHTS) have been analyzed and a stochastic PEV charging model has been defined based on survey results. The residential …

Development Of 3d Accelerometer Testing System, Mohammed Abbas Soudai Alsaedi

Dissertations and Theses

Accelerometers are used in numerous industries including aircrafts and missile navigations systems, rotary machines, and electronic devices such as tablets, cell phones, and cameras. Accelerometers of different purposes and specifications are being produced in large quantities. The large demand for accelerometers forces the need for accelerometer testing methodology that is more convenient and accurate. Inertial Micro-Electromechanical Systems Accelerometer (MEMS) require a series of tests that include physical stimuli. One of the key challenges is the cost associated with testing. Therefore, the accurate prediction of the sensor functions not only reduces the testing time but also more importantly contributes to reducing …

Mechanics Of Soft Polymers, Trisha Sain

TechTalks

Understanding the mechanics and physics of soft polymers are essential due to their widespread applications across disciplines. (e.g.-composite materials, bio mechanics, soft robotics etc.) The soft polymers in general inherent lightweight, high stretchability, extreme viscous damping and stimuli responsive behavior. Development of computational modeling strategy to predict their constitutive response, stimuli responsive behavior is indeed helpful for designing novel multifunctional soft composites, artificial mussels/tissues. In this talk I will briefly emphasize how we are developing multiscale-multiphysics based modeling methods for soft polymers to understand their macroscopic deformation mechanism, failure and other mechanical properties. The long term goal is to develop …

Aps Labs (Advanced Power Systems Research Center), Jeffrey D. Naber

TechTalks

Our mission is to promote & facilitate education and research in clean, efficient, and sustainable power and powertrain systems. The center was established in 2007 and in 2014 the 55,000 sq ft APSRC building located near the airport was denoted as a MTU core facility. Our new research contracts in FY2016 were over $2.5M. Our partners include automotive OEMs: GM, Ford, FCA, Toyota, Honda; Commercial OEMs: Cummins, Deere, Detroit, Isuzu, MHI; Suppliers: Delphi, Denso, Borg Warner, Hitachi; and DOE Labs: ANL, ORNL, PNNL, SNL, & INL. We have seven staff to assist in educational and R&D programs and facilities to …

Cluster Control Of A Multi-Robot Tracking Network And Tracking Geometry Optimization, Jasmine Cashbaugh

Engineering Ph.D. Theses

The position of a moving object can be tracked in numerous ways, the simplest of which is to use a single static sensor. However, the information from a single sensor cannot be verified and may not be reliable without performing multiple measurements of the same object. When multiple static sensors are used, each sensor need only take a single measurement which can be combined with other sensor measurements to produce a more accurate position estimate. Work has been done to develop sensors that move with the tracked object, such as relative positioning, but this research takes this concept one step …

Early Bearing Fault Analysis Using High Frequency Enveloping Techniques, Ilya Shulkin

Open Access Theses

High frequency acceleration enveloping is one of many tools that vibration analysts have at their disposal for the diagnosis of bearing faults in rotating machinery. This technique is believed to facilitate very early detection of potential failures by detecting low amplitude repetitive impacts in frequency ranges above conventional condition monitoring. One traditional enveloping method uses a mathematical operation known as the Hilbert transform along with other signal processing procedures such as band-pass filtering and full-wave rectification. For comparison, another method uses a proprietary algorithm included in National Instruments’ LabVIEWTM add-on package: Sound and Measurement Suite. Enveloping’s inherent problem with noise …

Design And Implementation Of A Fixture For Robotic Welding, Isaac Nathaniel Williams

Industrial and Manufacturing Engineering

The Cal Poly IME department recently purchased a robotic welder. The faculty would like to see this robot incorporated into the welding class. The robot was capable of moving, but was not able to perform a weld prior to this project. This problem is addressed by creating a demonstration part for the welding class. The objectives that need to be complete for this to be possible is designing a part, designing a fixture, analyzing the cost of robotic welding, and implement welding the part in the class. The part is designed with specific requirements in mind. The fixture is designed …

Application Of Gearbox Drivetrains For Commuting Bicycles, Loren Sunding

Industrial and Manufacturing Engineering

People all over the world are beginning to ride their bicycles more often to destinations which include work, school, and local markets. Most bicycles being used for these activities have an external drivetrain exposed to the elements of the road including water, mud, dirt, and debris. External drivetrains are very fragile and when damaged, pedaling efficiency is greatly reduced and the overall riding experience diminishes.

One solution to this issue is a gearbox specifically designed for a bicycle frame. A gearbox has several mechanical mechanisms operating inside a protective housing. Since the housing is fully sealed, outside elements are not …

Assembly Line Kitting: Foam Mold Material Substitute, Samer Samy Saleh

Industrial and Manufacturing Engineering

Kitting is considered an incredibly innovative and effective solution intended to aid operators within a mixed model assembly line. However, it is a non-value added procedure and one that customers may not be willing to pay for. With this project, the goal is to examine opportunities to employ lean principles and provide a solution that further eliminates non-value added procedures, while also producing the potential for a flexible, mixed model assembly line.

To achieve the aforementioned purpose, the production of foam molds, located within industrial totes and sent to the assembly line, was found to be a major waste within …

Energy-Efficient Management Of Mechanical Ventilation And Relative Humidity In Hot-Humid Climates, Florida Solar Energy Center, Charles Withers, Jr.

FSEC Energy Research Center®

The U.S. Department of Energy's Building America research team Building America Partnership for Improved Residential Construction conducted this research project to gain data and insight into these issues. The project focused on energy-efficient management of mechanical ventilation and RH during the cooling season. It consisted of eight test configurations. A particular focus evaluated how well a ductless seasonal energy-efficiency ratio (SEER) 21.5 mini-split heat pump (MSHP) could perform as the primary cooling system without a dehumidifier for supplemental dehumidification in a continuously mechanically ventilated house.

Passive Thermal Management Using Phase Change Materials, Yash Yogesh Ganatra

Open Access Theses

The trend of enhanced functionality and reducing thickness of mobile devices has led to a rapid increase in power density and a potential thermal bottleneck since thermal limits of components remain unchanged. Active cooling mechanisms are not feasible due to size, weight and cost constraints. This work explores the feasibility of a passive cooling system based on Phase Change Materials (PCMs) for thermal management of mobile devices. PCMs stabilize temperatures due to the latent heat of phase change thus increasing the operating time of the device before threshold temperatures are exceeded. The primary contribution of this work is the identification …

A Sharp Interface Isogeometric Strategy For Moving Boundary Problems, Tao Song

Open Access Dissertations

The proposed methodology is first utilized to model stationary and propagating cracks. The crack face is enriched with the Heaviside function which captures the displacement discontinuity. Meanwhile, the crack tips are enriched with asymptotic displacement functions to reproduce the tip singularity. The enriching degrees of freedom associated with the crack tips are chosen as stress intensity factors (SIFs) such that these quantities can be directly extracted from the solution without a-posteriori integral calculation.

As a second application, the Stefan problem is modeled with a hybrid function/derivative enriched interface. Since the interface geometry is explicitly defined, normals and curvatures can be …

Mri Upgrades At Radiology Associates, Patrick Cheung, Charlene Donlon

Industrial and Manufacturing Engineering

Problem Statement: The MRI machines at Radiology Associates are limiting the company’s ability to expand and compete within the local market. After discussing with technicians and managers at Radiology Associates, we decided to focus on hardware and software upgrades for the MRI machines. With 2 of the 3 locations purchasing new machines in the near future, our focus was on upgrades at the Santa Maria facility. The two machines at this location needed hardware and/or software upgrades to remain on par competitively both within the company and with local scanning options. Flexible coils are beneficial in terms of size, weight, …

Development Of A Process Monitoring Tool For The Manufacturing Process Of An Electric Vehicle Battery Enclosure, Ian Lamond

Industrial and Manufacturing Engineering

High volume manufacturing requires process control that is responsive to manufacturing related issues. It is critical that tools and resources are implemented that gauge manufacturing performance and identify root cause issues.

This project focuses on the design and manufacturing process of an electric vehicle aluminum battery enclosure and the implementation of a production measurement system. The current problem is a lack of process control communication and out of control alarms when uncontrolled events occur for manufacturing associates at the battery enclosure manufacturing work station.

This report examines the core principles of Quality Engineering, the economic advantages of implementing a vision …

Design And Prototyping Of An Adjustable Putter, Daulton Morgan

Industrial and Manufacturing Engineering

Being able to demo a golf putter is essential for a golfer since the feel of the putter is critical in determining what suits the golfer best. Due to the market being primarily dominated by right-handed players, it is difficult for left-handed players to demo high quality putters since the selection is sparse.

This report is about designing and integrating an interchangeable fastening system that allows a putter to be altered between a right and left-handed orientation, while still maintaining the traditional look of a putter. The report covers the necessary design steps, the prototyping of the putter, the projected …

Ole Miss Engineer 2016-2017

Ole Miss Engineer

No abstract provided.

A Validated Software Application To Measure Fiber Organization In Soft Tissue, Erica E. Morrill, Azamat N. Tulepbergenov, Christina J. Stender, Roshani Lamichhane, Raquel J. Brown, Trevor J. Lujan

Mechanical and Biomedical Engineering Faculty Publications and Presentations

The mechanical behavior of soft connective tissue is governed by a dense network of fibrillar proteins in the extracellular matrix. Characterization of this fibrous network requires the accurate extraction of descriptive structural parameters from imaging data, including fiber dispersion and mean fiber orientation. Common methods to quantify fiber parameters include fast Fourier transforms (FFT) and structure tensors, however, information is limited on the accuracy of these methods. In this study, we compared these two methods using test images of fiber networks with varying topology. The FFT method with a band-pass filter was the most accurate, with an error of 0.71 …

Selective Resistive Sintering: A Novel Additive Manufacturing Process, Austin Bryan Van Horn

Graduate Theses and Dissertations

Selective laser sintering (SLS) is one of the most popular 3D printing methods that uses a laser to pattern energy and selectively sinter powder particles to build 3D geometries. However, this printing method is plagued by slow printing speeds, high power consumption, difficulty to scale, and high overhead expense. In this research, a new 3D printing method is proposed to overcome these limitations of SLS. Instead of using a laser to pattern energy, this new method, termed selective resistive sintering (SRS), uses an array of microheaters to pattern heat for selectively sintering materials. Using microheaters offers significant power savings, significantly …

Towards Artificial Proprioception In The Mandibular Full Arch Fixed Implant Prosthesis, Md Abu Hasan

Mechanical and Aerospace Engineering Dissertations - Archive

Full arch fixed implant prosthesis has been one of the most effective treatment modalities for fully edentulous patients over the last few decades. However, due to lack of proprioception occlusal overload is experienced by the prosthesis and its components causing major biomechanical complications such as screw/abutment fracture, framework fracture, and bone loss. The currently available approaches for the overload management rely on external appliances such as an occlusal splint or bite guard and result in occlusal discomfort and high patient dissatisfaction. In this research, an approach to induce artificial proprioception in the full arch fixed implant prosthesis is proposed. However, …

A Framework For Employing Femtosatellites In Planetary Science Missions, Including A Proposed Mission Concept For Titan, Tracie Renea Conn Perez

Mechanical and Aerospace Engineering Dissertations - Archive

Over the past 15 years, there has been a growing interest in femtosatellites, a class of tiny satellites having mass less than 100 grams. Research groups from Peru, Spain, England, Canada, and the United States have proposed femtosat designs and novel mission concepts for them. In fact, Peru made history in 2013 by releasing the first – and still only – femtosat tracked from LEO. However, femtosatellite applications in interplanetary missions have yet to be explored in detail. An interesting operations concept would be for a space probe to release numerous femtosatellites into orbit around a planetary object of interest, …

Pilot Demonstration Based Reinforcement Learning With Application To Low Speed Airship Control, Onur Daskiran

Mechanical and Aerospace Engineering Dissertations - Archive

Designing control systems for airship has unique challenges as compared to conventional aircraft. Highly nonlinear dynamics, different mass/inertia relations, vast uncertainties in the model parameters and underactuation are the main reasons behind this. Airship dynamics is greatly influenced by the variations in the environmental (e.g.,room temperature) and internal (e.g., helium distribution in envelope) factors that can completely change the response characteristics of the blimp and make it infeasible for a model-based controller to perform. On the other hand, a skilled RC pilot can operate the manual flight easily under these conditions. This makes LfD (learning from demonstration) and RL (reinforcement …

A Stochastic Distributed Control Allocation Method Using Probability Collectives, Christopher Michael Elliot

Mechanical and Aerospace Engineering Dissertations - Archive

The configuration of the aerospace vehicle of tomorrow marches forward in complexity in step with technological advances in computation, materials, propulsion, and beyond. One of many attributes resulting from this evolution is the multiple effector concept, replacing the traditional aircraft design approach of a dedicated four channel mixer where pitch-roll-yaw-speed is controlled by elevator-aileron-rudder-engine, respectively. Instead, for example on the propulsion front, a distributed suite of smaller engines can substitute the larger power plant and can be used in concert for multiple axis control with both simultaneous, collective thrust for force generation and differential cyclic thrust for moment generation. The …

System Health Monitoring Using Multiple-Model Adaptive Estimation Techniques, Stanley Ryan Sifford

Mechanical and Aerospace Engineering Dissertations - Archive

Monitoring system health for fault detection and diagnosis by tracking system parameters concurrently with state estimates is approached using a new multiple-model adaptive estimation (MMAE) method. This novel method is called GRid-based Adaptive Parameter Estimation (GRAPE). GRAPE expands existing MMAE methods by using new techniques to sample the parameter space. GRAPE expands on MMAE with the hypothesis that sample models can be applied and resampled without relying on a predefined set of models. GRAPE is initially implemented in a linear framework using Kalman filter models. A more generalized GRAPE formulation is presented using extended Kalman filter (EKF) models to represent …

Numerical Modeling Of Capillary Driven Microfluidic Flow, Md Ashraful Islam

Mechanical and Aerospace Engineering Dissertations - Archive

Capillary driven two dimensional axisymmetric and three dimensional asymmetric flow in various microfluidic applications have been modeled and analyzed numerically. The transient Navier-Stokes equations are solved using a finite-difference formulation with a two-step projection method on a fixed grid. The vapor-liquid interface of the micro-droplet is tracked by volume-of-fluid (VOF) and coupled level set and volume-of-fluid (CLSVOF) methods with the surface tension force determined by the continuum surface force (CSF) model. The static contact angle at the three phase contact line has been modeled using wall adhesion scheme within the CSF framework. The developed numerical method for capturing the microfluidic …