Mechanical Engineering Commons^™

Wind Energy, Bob Deckard, Jaimee Howard

ENgaging Educators in Renewable enerGY (ENERGY): Lesson Plans & Slideshows (2017-2019)

No abstract provided.

Compact Humidity Sensor Based On A Multi-Layer Agarose Hydrogel Coated Silica Microsphere Resonator, Arun Mallik, Yuliya Semenova, Vishnu Kavungal, Dejun Liu

Conference Papers

In this paper we report on a novel approach to implementing a compact humidity sensor that utilizes whispering gallery mode (WGM) phenomena in a silica microsphere coated with Agarose hydrogel. The spectral positions of the WGM resonances for such a sensor depend strongly on the refractive index and thickness of the coating. The WGM’s spectral shift occurs due to adsorption/desorption of the water vapor in response to changes in ambient humidity and also due to the corresponding changes of the coating thickness. We experimentally investigated the WGMs spectral shift for a 100 μm diameter silica microsphere coated with Agarose hydrogel …

Precise Flow-Control Using Photo-Actuated Hydrogel Valves And Pid-Controlled Led Actuation, Colm Delaney, Simon Coleman, Jeff Whyte, Nigel Kent, Dermot Diamond

Articles

Herein we demonstrate remarkable control of flow within fluidic channels using photo-actuated hydrogel valves. By polymerizing the valves in situ it has been possible to create highly reproducible valves. Through the use of an LED platform and a PID algorithm we have generated extremely accurate flow control and created prototype devices to document their potential application within the microfluidics field.

Optimal Design And Freeform Extrusion Fabrication Of Functionally Gradient Smart Parts, Amir Ghazanfari

Doctoral Dissertations

"An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density was developed. In this process, an aqueous paste of ceramic particles with a very low binder content (<1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Sample parts made of alumina and fully stabilized zirconia were produced using this process and their mechanical properties including density, strength, Young's modulus, Weibull modulus, toughness, and hardness were examined. Microstructural evaluation was also performed to measure the grain size, and critical flaw sizes were obtained. The results indicate that the proposed method enables fabrication of geometrically complex parts with superior mechanical properties. Furthermore, several methods were developed to increase the productivity of the CODE process and enable manufacturing of functionally graded materials with an optimum distribution of material composition. As an application of the CODE process, advanced ceramic components with embedded sapphire optical fiber sensors were fabricated and properties of parts and sensors were evaluated using standard test methods"--Abstract, page iv.

Thermomechanical Fatigue Life Investigation Of An Ultra-Large Mining Dump Truck Tire, Wedam Nyaaba

Doctoral Dissertations

The cost benefits associated with the use of heavy mining machinery in the surface mining industry has led to a surge in the production of ultra-large radial tires with rim diameters in excess of 35 in. These tires experience fatigue failures in operation. The use of reinforcing fillers and processing aids in tire compounds results in the formation of microstructural inhomogeneity in the compounds and may serve as sources of crack initiation in the tire. Abrasive material cutting is another source of cracks in tires used in mining applications. It suffices, then, to assume that every material plane in the …

Event-Triggering Architectures For Adaptive Control Of Uncertain Dynamical Systems, Ali Talib Oudah Albattat

Doctoral Dissertations

"In this dissertation, new approaches are presented for the design and implementation of networked adaptive control systems to reduce the wireless network utilization while guaranteeing system stability in the presence of system uncertainties. Specifically, the design and analysis of state feedback adaptive control systems over wireless networks using event-triggering control theory is first presented. The state feedback adaptive control results are then generalized to the output feedback case for dynamical systems with unmeasurable state vectors. This event-triggering approach is then adopted for large-scale uncertain dynamical systems. In particular, decentralized and distributed adaptive control methodologies are proposed with reduced wireless network …

Characterization And Numerical Simulation Of The Microstructural And Micromechanical Viscoelastic Behavior Of Oil Sands Using The Discrete Element Method, Eric Kofi Gbadam

Doctoral Dissertations

"Oil sands are naturally geologic formations of predominantly quartz sand grains whose void spaces are filled with bitumen, water, and dissolved gases. The electric rope shovel is the primary equipment used for excavating the Athabasca oil sand formations. The equipment's static and dynamic loads are transferred to the formation during excavation and propel. These loads cause ground instability leading to sinkage or rutting, crawler wear, and fracture failures. These problems result in unplanned downtimes, production losses, and high maintenance costs. In order to address these problems, there is a need to develop valid models that capture the behavior and performance …

Continuous Focusing And Separation Of Microparticles With Acoustic And Magnetic Fields, Ran Zhou

Doctoral Dissertations

"Microfluidics enables a diverse range of manipulations (e.g., focusing, separating, trapping, and enriching) of micrometer-sized objects, and has played an increasingly important role for applications that involve single cell biology and the detection and diagnosis of diseases. In microfluidic devices, methods that are commonly used to manipulate cells or particles include the utilization of hydrodynamic effects and externally applied field gradients that induce forces on cells/particles, such as electrical fields, optical fields, magnetic fields, and acoustic fields.

However, these conventional methods often involve complex designs or strongly depend on the properties of the flow medium or the interaction between the …

Numerical And Experimental Study Of New Designs Of All-Vanadium Redox Flow Batteries For Performance Improvement, Mohammed Abdulkhabeer Ali Al-Yasiri

Doctoral Dissertations

"Energy storage is envisioned as a key part of a renewable energy solution incorporated in a grid that overcomes two critical limits of renewable energy: intermittency and uncertainty. Among various technologies, a vanadium redox flow battery (VRFB) offers a promise because of its unique features such as long cycle life, separation of energy and power ratings, and capability of a deep discharge. The remaining challenges, however, include the limited application due to low energy density and complicated geometries. The complex geometry makes it difficult to optimize the performance and can cause a serious concern about leakage of the liquid. The …

Repair Of Metallic Components Using Hybrid Manufacturing, Renwei Liu

Doctoral Dissertations

"Many high-performance metal parts users extend the service of these damaged parts by employing repair technology. Hybrid manufacturing, which includes additive manufacturing (AM) and subtractive manufacturing, provides greater build capability, better accuracy, and surface finish for component repair. However, most repair processes still rely on manual operations, which are not satisfactory in terms of time, cost, reliability, and accuracy. This dissertation aims to improve the application of hybrid manufacturing for repairing metallic components by addressing the following three research topics. The first research topic is to investigate and develop an efficient best-fit and shape adaption algorithm for automating 3D models' …

Manufacturing Of Advanced Continuous Fiber Reinforced Composites For High Temperature Applications, James Robert Nicholas

Doctoral Dissertations

"New resin systems have enabled composites to be considered as attractive alternatives in structural applications that require material to be stronger, lighter and/or more resilient to environmental effects. The current work is on the development of processes to produce continuous fiber reinforced materials from two state of the art resin systems. Two processes were developed to produce continuous fiber reinforced ceramic materials from a preceramic polymer. The first was a vacuum forming process developed using the out-of-autoclave polymer composite manufacturing technique in conjunction with the polymer infiltration and pyrolysis process to produce ceramic composite material of zirconium diboride-silicon carbide reinforced …

Volumetric Error Compensation For 5-Axis Machine Tools, Jennifer Ruth Creamer

Doctoral Dissertations

"This work presents a geometric error compensation method for large 5-axis machine tools. The compensation method presented here uses tool tip measurements recorded throughout the axis space to construct a position-dependent geometric error model that can easily be used for error compensation. The measurements are taken using a laser tracker, permitting rapid error data gathering at most locations in the axis space. First two model types are compared for generating table-based error compensation and experimental results are presented. Table-based compensation is then extended to machine tool controller types with restrictions on the number or combination of compensation tables using an …

Control Of Single- And Dual-Probe Atomic Force Microscopy, Muthukumaran Loganathan

Doctoral Dissertations

“Atomic force microscope (AFM) is one of the important and versatile tools available in the field of nanotechnology. It is a type of probe-based microscopy wherein an atomically sharp tip, mounted on the free end of a microcantilever, probes the surface of interest to generate 3D topographical images with nanoscale resolution. An integral part of the AFM is the feedback controller that regulates the probe deflection in the presence of surface height changes, enabling the control action to be used for generating topographical image of the sample. Besides sensing, the probe can also be used as a mechanical actuator to …

Additive Manufacturing Of Glass Using A Filament Fed Process, Junjie Luo

Doctoral Dissertations

"There are many scientific and engineering applications of glass including optics, communications, electronics, and hermetic seals, there has been minimal research towards the Additive Manufacturing (AM) of transparent glass parts. The special thermal and optical properties of glasses make them hard to be printed using conventional AM techniques. In this dissertation, two different AM techniques for glass AM were developed, Selective Laser Melting (SLM) and filament fed process.

Semi-transparent parts were printed with SLM process. However, the filament fed process was found to be more robust and promising for printing optically transparent glass parts. Therefore, this dissertation is focused on …

Reliability Prediction In Early Design Stages, Yao Cheng

Doctoral Dissertations

"In the past, reliability is usually quantified with sufficient information available. This is not only time-consuming and cost-expensive, but also too late for occurred failures and losses. For solving this problem, the objective of this dissertation is to predict product reliability in early design stages with limited information. The current research of early reliability prediction is far from mature. Inspired by methodologies for the detail design stage, this research uses statistics-based and physics-based methodologies by providing general models with quantitative results, which could help design for reliability and decision making during the early design stage. New methodologies which accommodate component …

Error Mapping Of Build Volume In Selective Laser Melting, Ninad Kulkarni

Masters Theses

“Selective laser melting is one of the commonly used additive manufacturing processes employed for production of functional part. Therefore, quality aspects such as dimensional accuracy have become a point of great interest. Like all of the other additive manufacturing processes selective laser melting process suffers from the issue if having wide range of process parameters making the process control a complex task. Additionally, issues specific to the selective laser melting process such as position dependency of accuracy of the part, makes it difficult to predict the resulting dimensional inconsistencies in the part manufactured by this processes. This research is an …

Ti-Fe Intermetallics Analysis And Control In Joining Titanium Alloy And Stainless Steel By Laser Metal Deposition, Wei Li

Masters Theses

"Direct fusion joining titanium alloy and stainless steel can cause brittle Ti-Fe intermetallics which compromise the mechanical properties of diffusion bonds between titanium alloys and stainless steel. Therefore, filler metals are required as transition layers. In this research, stainless steel metallic powder was directly deposited on the titanium alloy substrate by laser beam, the Ti-Fe intermetallic phases formed in this process were investigated through analyzing fracture morphology, phase identification, and Vickers Hardness Number (VHN). After that, Laser Metal Deposition (LMD) was applied to explore a new fabricating process to join Ti6Al4V and SS316. A transition composition route was introducedTi6Al4V → …

Cathodic Protection Measurement Through Inline Inspection Technology Uses And Observations, Briana Ley Ferguson

Masters Theses

"This research supports the evaluation of an impressed current cathodic protection (CP) system of a buried coated steel pipeline through alternative technology and methods, via an inline inspection device (ILI, CP ILI tool, or tool), in order to prevent and mitigate external corrosion. This thesis investigates the ability to measure the current density of a pipeline's CP system from inside of a pipeline rather than manually from outside, and then convert that CP ILI tool reading into a pipe-to-soil potential as required by regulations and standards. This was demonstrated through a mathematical model that utilizes applications of Ohm's Law, circuit …

Controlled Manipulation Of Floating Objects On Deformed Fluid Interfaces And Conditions For Stable Equilibria, Jose M. Carballo, Qi Ni, Jose Vasquez, Nathan B. Crane

Faculty Publications

At the millimeter scale, interactions between floating and semi-immersed objects are significant. The local curvature of the interface is modified by the weight/buoyancy forces of floating objects, and by the surface properties of semi-immersed objects. The curvature changes generate attractive (or repulsive) interactions between floating parts, and semi-immersed objects. This work demonstrates how electrowetting can manipulate these interactions in order to position, align, assemble and transport parts attached to the fluid interface. This demonstrates one way in which fluid interfaces can provide an alternative to standard pick and place technology for part positioning/assembly. Typically, the part/rod forces are purely attractive …

Onboard Load Sensor For Use In Freight Railcar Applications, Constantine Tarawneh, Jazmin Ley, Dylan Blackwell, Stephen Crown, Brent Wilson

Mechanical Engineering Faculty Publications

Approximately 40% of intercity freight transportation occurs by rail, making it the most widely used method of transporting large commodities. This trend is expected to persist over the next thirty years as our highway systems are strained and experiencing increased congestion and costly delays. Currently, the load of freight railcars is typically measured by weighbridges or retrofitted tracks at isolated locations. This practice is not efficient and limited by the fact that the load of the railcar cannot be monitored continuously, not to mention the inherent inaccuracies of such systems. Hence, there is great merit for an onboard load sensor …

High Sensitivity Refractometer Based On Reflective Smf-Small Diameter No Core Fiber Structure, Guorui Zhou, Qiang Qu, Rahul Kumar, Wai Pang Ng, Hao Liu, Longfei Niu, Nageswara Lalam, Xiaodong Yuan, Yuliya Semenova

Conference Papers

A high sensitivity refractive index sensor based on a single mode-small diameter no core fiber structure is proposed. In this structure, a small diameter no core fiber (SDNCF) used as a sensor probe, was fusion spliced to the end face of a traditional single mode fiber (SMF) and the end face of the SDNCF was coated with a thin film of gold to provide reflective light. The influence of SDNCF diameter and length on the refractive index sensitivity of the sensor has been investigated by both simulations and experiments, where results show that the diameter of SDNCF has significant influence. …

Retarding Field Energy Analyzer For High Energy Pulsed Electron Beam Measurements, J. Hu, Joshua L. Rovey, W. Zhao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Flexural Creep Behavior Of Adhesively Bonded Metal And Composite Laminates, Hasan M. Nuwayer

Wayne State University Dissertations

Adhesively bonded structures exhibit time dependent behavior when subjected to constant load (creep). In this investigation, long-term creep behavior of adhesively bonded aluminum and carbon fiber composite beams under flexural loading was investigated. Three point bending test was selected because of its simplicity and the fact that bending stresses are quite common. In this study, two types of adhesively bonded beam specimens were tested: specimens prepared by adhesively bonding two aluminum beams and specimens prepared by adhesively bonding two unidirectional carbon fiber laminated beams. Accelerated creep tests were performed at higher temperatures up to 60 °C and deflection was measured …

Probabilistic Analysis And Verification Framework For Adaptive Flight Control, Mario Luca Fravolini, Tansel Yucelen, Marcello Napolitano

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A crucial aspect that could facilitate the applications of adaptive control systems in aerospace applications is the development of effective validation and verification procedures. Most of the existing analysis and design frameworks for adaptive controllers are based on the Lyapunov direct method. One well-known drawback of this approach is the conservatism in the estimation of the uniform ultimate boundedness region with little practical utility. To overcome this limitation, a probabilistic framework for the design of uniform ultimate boundedness regions is proposed where uncertain parameters and adaptive controls are considered as random variables. In this framework, the design is translated into …

Molecular Simulation Of Steady-State Evaporation And Condensation: Validity Of The Schrage Relationships, Zhi Liang, Thierry Biben, Pawel Keblinski

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Accuracy, or Even the Validity, of the Schrage Relationships Expressing the Rate of Evaporation and Condensation in Terms of Local Interfacial Thermodynamics Properties and the Mass Accommodation Coefficient is a Subject of Significant Discussion. in This Work, We Carry Out Molecular Dynamics (MD) Simulations of Evaporation and Condensation of Fluid Ar in a Nanochannel. by Adjusting the Temperature Difference, ΔT, between the Evaporating and Condensing Surfaces, We Control the Steady-State Evaporation and Condensation Fluxes (JMD). We Find that Across a Wide ΔT Range Studied, JMD is Always in Excellent Agreement with the Prediction from the Exact Schrage Relationships. Furthermore, …

3d Bioprinting Of Stem Cells And Polymer/Bioactive Glass Composite Scaffolds For Bone Tissue Engineering, Caroline Murphy, Krishna Kolan, Wenbin Li, Julie A. Semon, D. E. Day, Ming-Chuan Leu

Biological Sciences Faculty Research & Creative Works

A major limitation of using synthetic scaffolds in tissue engineering applications is insufficient angiogenesis in scaffold interior. Bioactive borate glasses have been shown to promote angiogenesis. There is a need to investigate the biofabrication of polymer composites by incorporating borate glass to increase the angiogenic capacity of the fabri-cated scaffolds. In this study, we investigated the bioprinting of human adipose stem cells (ASCs) with a polycaprolac-tone (PCL)/bioactive borate glass composite. Borate glass at the concentration of 10 to 50 weight %, was added to a mixture of PCL and organic solvent to make an extrudable paste. ASCs suspended in Matrigel …

Statistical Shape Modeling To Quantify Variation In The Proximal Humeral Anatomy, Paul B. Sade Sr.

Electronic Theses and Dissertations

The fit of the humeral prosthesis to the intramedullary canal and the replication of the anatomic humeral head center are important factors in Total Shoulder Arthroplasty (TSA). The objective of this thesis was to develop a Statistical Shape Model (SSM) of the cortical and cancellous bone regions of the proximal humerus, and to assess potential shape differences with gender and ethnicity, with a goal of informing implant design. An SSM was used and Principal Component Analysis (PCA) was applied to data that represented both the cancellous and cortical humeral bone of 63 healthy subjects and cadavers. Anatomical measurements and PC …

Osteogenic Potential Of Poly (L-Lactic Acid) Scaffolds Prepared By Thermally Controlled Methods On Human Adipose Derived Stem Cells, Harish Chinnasami Shanmugam

LSU Doctoral Dissertations

Thermally Induced Phase Separation (TIPS) method was used to make porous three-dimensional PLLA scaffolds. The effect of imposed thermal profile during freezing of the PLLA in dioxane solution on the scaffold was characterized by their micro-structure, porosity (%), pore-sizes distribution and mechanical strength. The porosity (%) decreased considerably with increasing concentrations of PLLA in the solution, while a decreasing trend was observed with increasing cooling rates. The mechanical strength increases with increase in PLLA concentration and also with increase in the cooling rate for both types of solvents. Therefore, mechanical strength was increased by higher cooling rates while the porosity …

Novel Design Of Nanostructured Material For Advanced Energy Conversion And Storage Devices, Wangwang Xu

LSU Master's Theses

Nowadays, the fast-increasing energy demand for efficient, sustainable and environmentally-friendly energy storage devices remains a significant and challenging issue. Lithium ion batteries (LIBs) have been widely used as commercial energy devices in portable electronics and also shown great promise in upcoming large scale applications due to their advantages of environmental safety, efficiency in energy delivering and light weight. However, due to their limited capacity, energy densities and cycle ability, LIBs still need further improvement to expand their applications to a larger field, especially electric vehicle (EVs) and hybrid electric vehicles (HEVs), in which energy storage devices with large capacity and …

Development Of Laboratory Scale Conical Spouted Bed Reactors, James Blake Gegenheimer

LSU Master's Theses

Conical spouted beds (CSBs) are a form of a fluidized bed that is characteristic of its spouting behaviors. The conical spouted bed has a small inlet that diverges through a conical section towards a larger fixed-diameter column which is filled with static spouting media. By injecting a fluid at a sufficient velocity, a small spout will form in which the spouting media will become entrained by the fluid particles and carried to the top of the system where it will circulate back into the system. It has been shown that CSB reactors have the potential for increasing the heat circulation …