Mechanical Engineering Commons^™

Role Of Copper Oxide Layer On Pool Boiling Performance With Femtosecond Laser Processed Surfaces, Corey Kruse, Edwin Peng, Craig Zuhlke, Jeff Shield, Dennis Alexander, Sidy Ndao, George Gogos

Department of Mechanical and Materials Engineering: Faculty Publications

Copper pool boiling surfaces are tested for pool boiling enhancement due to femtosecond laser surface processing (FLSP). FLSP creates self-organized micro/nanostructures on metallic surfaces and creates highly wetting and wicking surfaces with permanent surface features. In this study two series of samples were created. The first series consists of three flat FLSP copper surfaces with varying microstructures and the second series is an open microchannel configuration with laser processing over the horizontal surfaces of the microchannels. These microchannels range in height from 125 microns to 380 microns. Each of these surfaces were tested for pool boiling performance. It was found …

Modified Qigong Breathing Exercise For Reducing The Sense Of Hunger On An Empty Stomach, Alexander P. Voroshilov, Alex A. Volinsky, Zhixin Wang, Elena V. Marchenko

Mechanical Engineering Faculty Publications

Background: The aims of this study were to determine whether a modified Qigong breathing exercise can reduce the sense of hunger and identify possible mechanisms.

Methods: The results from the test group, which performed the exercise, are compared with the control group, which performed deep breathing. Intestinal pressure measurements, stomach pH monitoring, and participant surveys were used for assessment.

Results: Stomach pH was increased by 3 (0.2) and intestinal pressure was reduced by 12 (0.5) mm Hg in the experimental group and did not change significantly in the control group. The study provides strong evidence that the exercise can significantly …

Models For The Residual Life Of Railroad Bearing Grease In Laboratory And Industry Applications, Douglas Timmer, Constantine Tarawneh, Robert Jones

Manufacturing & Industrial Engineering Faculty Publications

Adequate lubrication in railroad bearings is crucial to the safe operation of these components. An investigation of the residual life of railroad bearing grease was conducted in a laboratory setting. The data was collected using a split-split-plot design of experiments. The Oxidation Induction Time (OIT), which is the time required for the remaining antioxidants in a sample of grease to be consumed in a test, is the response variable for this study. Low values of OIT indicate small remaining amounts of antioxidants in the grease and thus small remaining residual life in the grease. OIT measurements were made using differential …

Manual Revision Process For Project-Based Laboratory Instruction, Gene Hou, Feifei Zhong, Orlando M. Ayala

Mechanical & Aerospace Engineering Faculty Publications

A four-step laboratory manual revision process was developed in this study based upon a technical writing process for supporting project-based laboratory classes. The audience and the objectives of this type of laboratory manuals are quite different from those of traditional, descriptive laboratory classes. The project-based laboratory manual has to serve as both an operational handbook and a theoretical textbook. The proposed four-step manual revision process was implemented in the fall 2016 semester in a 3-credit, senior elective class which was built upon a commercially-rated finite element analysis software package. Student surveys and evaluations showed that the revision process greatly increased …

An Integrated Curriculum For Technical Writing In Higher Education In China, Feifei Zhong, Gene Hou

Mechanical & Aerospace Engineering Faculty Publications

This study aims to develop an effective curriculum plan to improve technical writing in higher education in China. The paper first investigated the deficiency in the curriculum design in China for English technical writing by comparing the required courses offered in Southwest Jiaotong University (SWJTU) in China with those in Old Dominion University (ODU) in US. Questionnaires and interviews were then conducted among studying abroad Chinese students, visiting scholars, English as Second Language (ESL) instructors as well as engineering professors. The collected data revealed that the oversea Chinese students were struggled more with higher order concerns in writing than lower …

Study Of Stability And Thermal Conductivity Of Nanoparticles In Propylene Glycol, Sumit Mahajan

All Graduate Theses, Dissertations, and Other Capstone Projects

This thesis studied the effects of gravity induced settling, thermophoresis and Brownian motion on the thermal conductivity of the Aluminum Oxide (Al2O3) nanofluids. The base fluid was propylene glycol. The effects were studied by making three samples with volumetric percentages of 0.2 %, 2% and 3% Al2O3 in propylene glycol. Sets of 22 experiments were conducted over time to understand the behavior of settling. All samples were manually mixed each time the experiment was conducted. A Thermtest Transient Plane Source TPS 500S was used to measure the thermal conductivity. Volumetric percentages and diameters of nanoparticle were chosen so that the …

Mechanical Property Characterization Of Discontinuous Fiber Reinforced Composites By Computer Modeling, Amrit Bhusal

Electronic Theses and Dissertations

The desire to make high strength, lightweight, less corrosive, high fatigue resistance materials in auto industries, aero industries, biomedical industries have given a chance for in-depth study of composite materials. To get the profound knowledge of composites, different experiments are conducted which often take huge resources, cost and time. Computer modeling and analysis have gained popularity in Finite Element Analysis (FEA) because it can be used to predict the mechanical property of different materials. In this thesis, FEA technique has been used to predict mechanical property of discontinuous fiber reinforced composites (FRC). If we are able to foretell the mechanical …

Assessing The Near-Wall Hemodynamics In The Left Coronary Artery Using Cfd, John Junior Asiruwa

Electronic Theses and Dissertations

The objective of this thesis is to computationally investigate the flow mechanics and the near-wall hemodynamics associated with the different take-off angles in the left coronary artery of the human heart. From this study, we will be able to evaluate if the increase in the take-off angles of the left coronary artery will significantly increases or decrease the likelihood of plaque (atherosclerosis) buildup in the left coronary artery bifurcations. This study quantifies the effects of the varying take-off angles on the branches along the left anterior descending (LAD) of the left coronary artery using computational fluid dynamics (CFD) simulations. The …

Development Of Heterogeneous Catalysts For Upgrading Biomass Pyrolysis Bio-Oils Into Advanced Biofuels, Shouyun Cheng

Electronic Theses and Dissertations

The massive consumption of fossil fuels and associated environmental issues result in an increased interest in alternative resources such as biofuels. The renewable biofuels can be upgraded from bio-oils that are derived from biomass pyrolysis. Catalytic cracking and hydrodeoxygenation (HDO) are two most promising bio-oil upgrading techniques for biofuel production. Heterogeneous catalysts are essential for upgrading bio-oil into hydrocarbon biofuel. Although some progresses have been made, the cost and effectiveness of catalysts still remain challenges. The main objective of this study was to develop efficient heterogeneous catalysts for upgrading bio-oils into advanced hydrocarbon biofuel with low costs. In catalytic cracking, …

The New Designing Of The Nano-Indentation Method To Applying On The Aisi D-2 Steel, Tangyue Wu

Wayne State University Theses

In this thesis, it is mainly to describe the new designed nano-indenataion. This kind of nano-indentation apparatus is much more inexpensive and almost has the same function to compare with the commercial one. The nano-indentation system can get the force-displacement wave, which is the way to determine the elastic and plastic properties for the particle materials. In the structure, it would describe the designing of the nano-indentation apparatus for a big partial of the thesis. This part is divided into 3 sub-part: hardware designing, software designing and data processing. The material, D2, is chosen to do the force-displacement wave, which …

Condition Assessment Of End-Of-Use Products For Remanufacturing, Jovan Morgan

Research Opportunities for Engineering Undergraduates (ROEU) Program 2016-17

The goal of the project is to use the automated 3-D laser scanner using a Capnut as a test object to detect surface defects, corrosion and calculation error through offline quality inspection. potentially reducing labor time and cost for both consumers and manufacturers.

Atomically Informed Nonlocal Semidiscrete Variational Peierls-Nabarro Model For Planar Core Dislocations, Guisen Liu, Xi Cheng, Jian Wang, Kaiguo Chen, Yao Shen

Department of Mechanical and Materials Engineering: Faculty Publications

Prediction of Peierls stress associated with dislocation glide is of fundamental concern in understanding and designing the plasticity and mechanical properties of crystalline materials. Here, we develop a nonlocal semi-discrete variational Peierls-Nabarro (SVPN) model by incorporating the nonlocal atomic interactions into the semi-discrete variational Peierls framework. The nonlocal kernel is simplified by limiting the nonlocal atomic interaction in the nearest neighbor region, and the nonlocal coefficient is directly computed from the dislocation core structure. Our model is capable of accurately predicting the displacement profile, and the Peierls stress, of planar-extended core dislocations in face-centered cubic structures. Our model could be …

Photoluminescence From Radiative Surface States And Excitons In Methylammonium Lead Bromide Perovskites, Dengyang Guo, Davide Bartesaghi, Haotong Wei, Eline M. Hutter, Jinsong Huang, Tom J. Savenije

Department of Mechanical and Materials Engineering: Faculty Publications

In view of its band gap of 2.2 eV and its stability, methylammonium lead bromide (MAPbBr₃) is a possible candidate to serve as a light absorber in a subcell of a multijunction solar cell. Using complementary temperature-dependent time-resolved microwave conductance (TRMC) and photoluminescence (TRPL) measurements, we demonstrate that the exciton yield increases with lower temperature at the expense of the charge carrier generation yield. The low-energy emission at around 580 nm in the cubic phase and the second broad emission peak at 622 nm in the orthorhombic phase originate from radiative recombination of charges trapped in defects with …

Helium Irradiation And Implantation Effects On The Structure Of Amorphous Silicon Oxycarbide, Qing Su, Shinsuke Inoue, Manabu Ishimaru, Jennifer A. Gigax, Tianyao Wang, Hepeng Ding, Michael J. Demkowicz, Lin Shao, Michael Nastasi

Department of Mechanical and Materials Engineering: Faculty Publications

Despite recent interest in amorphous ceramics for a variety of nuclear applications, many details of their structure before and after irradiation/implantation remain unknown. Here we investigated the short-range order of amorphous silicon oxycarbide (SiOC) alloys by using the atomic pair-distribution function (PDF) obtained from electron diffraction. The PDF results show that the structure of SiOC alloys are nearly unchanged after both irradiation up to 30 dpa and He implantation up to 113 at%. TEM characterization shows no sign of crystallization, He bubble or void formation, or segregation in all irradiated samples. Irradiation results in a decreased number of Si-O bonds …

Suspended Graphene-Based Gas Sensor With 1-Mw Energy Consumption, Jong-Hyun Kim, Qin Zhou, Jiyoung Chang

Department of Mechanical and Materials Engineering: Faculty Publications

This paper presents NH₃ sensing with ultra-low energy consumption for fast recovery and a graphene sheet based on a suspended microheater. Sensitivity and repeatability are important characteristics of functional gas sensors embedded in mobile devices. Moreover, low energy consumption is an essential requirement in flexible and stretchable mobile electronics due to their small dimension and fluctuating resistivity during mechanical behavior. In this paper, we introduce a graphene-based ultra-low power gas detection device with integration of a suspended silicon heater. Dramatic power reduction is enabled by a duty cycle while not sacrificing sensitivity. The new oscillation method of heating improves …

Vorticella: A Protozoan For Bio-Inspired Engineering, Sangjin Ryu, Rachel E. Pepper, Moeto Nagai, Danielle C. France

Department of Mechanical and Materials Engineering: Faculty Publications

In this review, we introduce Vorticella as a model biological micromachine for microscale engineering systems. Vorticella has two motile organelles: the oral cilia of the zooid and the contractile spasmoneme in the stalk. The oral cilia beat periodically, generating a water flow that translates food particles toward the animal at speeds in the order of 0.1–1 mm/s. The ciliary flow of Vorticella has been characterized by experimental measurement and theoretical modeling, and tested for flow control and mixing in microfluidic systems. The spasmoneme contracts in a few milliseconds, coiling the stalk and moving the zooid at 15–90 mm/s. Because the …

Combustion Phasing Through Combustion Ionization In A Caterpillar C7 Compression Ignition Engine, Kamal Ashraf Assaad

Wayne State University Theses

To achieve the goals of best fuel economy, peak power and low soot emissions in military engines it is necessary to control the combustion process. An in-cylinder combustion sensor is required to achieve the goals of controlling the combustion process. Over the last four decades, in-cylinder pressure transducers and ion current sensors have been available for research and development. Most of the effort has focused on the pressure transducer, however up till now a pressure transducer suitable for use in production engines has not been developed yet, because of cost and durability concerns.This work presents the analysis of experimental data …

Model Advancement And Hil Setup For Testing A P2 Phev Supervisory Controller, Sajjan Balakrishnan

Wayne State University Theses

Teams participating in Advanced Vehicle Technology Competitions such as EcoCAR3 are often bound by limited time and resources. Moreover, vehicle and component downtime due to mechanical and electrical issues reduce the time available for testing activities demanded by the Controls/Systems Modeling and Simulation teams. Therefore, the teams would benefit from identifying new approaches and being more pragmatic and productive in order to achieve satisfactory progress in the competition. This thesis summarizes the approach taken to improve the simulation accuracy of the Wayne State University EcoCAR3 team’s Pre-transmission Parallel Hybrid Electric Vehicle plant model and HIL setup. Focus is on testing …

Development Of Hybrid Supervisory Controller And Energy Management Strategy For P2 Phev, Guilin Zhu Zhu

Wayne State University Theses

The EcoCAR3 project is a four-year competition sponsored by General Motors and the U.S. Department of Energy challenging 16 universities teams to reengineer a 2016 Chevrolet Camaro to be a performance plug-in hybrid electric vehicle. A pre-transmission (P2) without clutch parallel architecture was chosen by Wayne State University EcoCAR3 team in Year 3.

The parallel PHEV architecture was modeled by using MATLAB, Simulink and Stateflow for the MIL and SIL environment which was used to test different control strategies. To efficiently distribute the power between engine and electric motor and assess component and system statuses, a hybrid supervisory controller was …

Anomalous Decay Of Nanomechanical Modes Going Through Nonlinear Resonance, Oriel Shoshani, Steven W. Shaw, Mark I. Dykman

Mechanical and Civil Engineering Faculty Publications

Because of the small size of nanomechanical systems, their vibrations become nonlinear already for small amplitudes. Many nontrivial aspects of the vibration dynamics arise from the coexistence of several nonlinearly coupled modes. We show that such coupling can lead to anomalous decay of the modes where they go through nonlinear resonance, so that their amplitude-dependent frequencies become commensurate. We demonstrate the possibility of a strongly nonmonotonic dependence of the decay rate on the amplitude if one of the modes serves as a thermal reservoir for another mode. Where the decay of both modes is slow compared to the rate of …

Research Area 4: Nondestructive Evaluation (Nde) Techniques, Vlsj Lab, Mechanical Engineering Department, Georgia Southern University

VLSJ Lab: Research Areas (Archived)

No abstract provided.

Impact Of Pretreatment Methods On Fast Pyrolysis Of Biomass, Yash Donepudi

Dissertations, Master's Theses and Master's Reports

Biomass is considered a renewable source of energy with minimum carbon foot print if managed sustainably. The majority of the worlds energy is spend on transportation, and fast pyrolysis of biomass could be a potential route for production of a sustainable liquid transportation fuel. However, there are several hurdles in the conversion process. This work addresses these hurdles by investigating the impact of several pretreatment methods on fast pyrolysis including thermal pretreatment (torrefaction), comminution/grinding, mineral reduction. The impact of important parameters like heat transfer medium, conversion temperature and particle size were also investigated.

A mild thermal pretreatment of biomass (~10-15% …

Nanotextured Titanium Surfaces For Implants: Manufacturing And Packaging Aspects, Sachin Bhosle

Dissertations, Master's Theses and Master's Reports

It has been shown that nanotexturing the surface of otherwise smooth titanium orthopedic materials increases osteoblast proliferation in vitro, and the bone-implant contact area and pullout force in vivo. However, this prior work has not focused on the requirements for scale-up to industrial processes. This dissertation reports on titanium surface modifications by electrochemical anodization using a benign NH₄F electrolyte, and a hybrid electrolyte also containing AgF, rather than hazardous hydrofluoric acid used elsewhere. Nanotube fabrication of Ti6Al4V foils, rods, thermal plasma sprayed commercial implants, and laser and e-beam melted powder materials was demonstrated.

It was found …

Integrative Experiences Through Modeling And Simulation Of Mechatronic Systems, Mileta Tomovic, Cynthia Tomovic, Vukica M. Jovanovic, Cheng Y. Lin, Nan Yao, Petros J. Katsioloudis

Engineering Technology Faculty Publications

Learning is integrative lifelong process which requires continuous refreshing of old material and learning new material. This principle holds also for student experiences during their undergraduate studies. Students learn new material throughout their studies, and they may or may not have opportunity to use the material in different context and at different levels. As a result some of the acquired knowledge may be forgotten by the time student graduates or it may not be placed in the context of the overall program outcomes, thus material presented may not seem to have relevance to student's career. An effective method to address …

Developing A Curriculum For Marine Mechatronics Technicians, Vukica M. Jovanovic, Petros J. Katsioloudis, Ana Djuric, Mileta Tomovic, Thomas B. Stout

Engineering Technology Faculty Publications

A growing trend within the U.S. Navy is to streamline operations by deploying ships with less sailors, who are more highly skilled technicians that are trained to do a wide array of jobs. Modern ships also include various automated systems that require more highly skilled technicians for maintenance. Outdated warship designs are now being replaced with industrial grade automation equipment. Such equipment is being used in warships that encounter harsher environments than what exists in the civilian industry. Hence, there is a need for training in regards to industrial grade automation equipment for military and civilian ship repair partners. Marine …

Research Area 1: Vehicle Lightweight Design And Safety, Vlsj Lab, Mechanical Engineering Department, Georgia Southern University

VLSJ Lab: Research Areas (Archived)

No abstract provided.

Mechanical And Computational Evaluation Of Cementitious Materials With Hollow Glass Microsphere Inclusions, Zachary J. Wallace

Electronic Theses and Dissertations

The effect of volumetric replacement of cementitious materials by an inert filler known as hollow glass microspheres on elastic properties is evaluated in this study through a combined computational and experimental approach. This approach considered the variation in properties of type I Portland cement for 0, 5, 10, and 15% volume fractions of two kind of glass microspheres; one was high density with high crushing strength, and the other with a relative lower density. Using a suite of software called Virtual Cement and Concrete Testing Laboratory (VCCTL), the microstructural details were determined for 80% degree of hydration of the cement …

Promotional Effect Of Molten Carbonates On Proton Conductivity And Oxygen Reduction Reaction – An Experimental And Computational Study, Xiaolei Xiong

Theses and Dissertations

Recent research of Solid oxide fuel cells (SOFCs) is aimed to lower the operating temperature to an intermediate temperature (IT) range of 500 to 700^oC, while maintaining a proper performance. This Ph.D. research project investigates the promotional effects of alkaline carbonate eutectics on the proton conductivity of proton conducting electrolytes and cathodic ORR reactivity in SOFCs by both experimental and computational methods. The ionic conductivity of the MC-BZY composite above 500^oC increases with the higher loading of MC. The sample exhibited nearly a factor of two higher conductivity in H₂-containing atmosphere than in air. …

Wrinkling Of Functionally Graded Sandwich Structures Subject To Biaxial And In-Plane Shear Loads, Harold Costa

Masters Theses

"Benefits of a functionally graded core increasing wrinkling stability of sandwich panels have been demonstrated in a recent paper [1] where a several-fold increase in the wrinkling stress was observed, without a significant weight penalty, using a stiffer core adjacent to the facings. In the present paper wrinkling is analyzed in case where the facings are subject to biaxial compression and/or in-plane shear loading and the core is arbitrary graded through-the-thickness. Two issues addressed are the effect of biaxial or in-plane shear loads on wrinkling stability of panels with both graded and ungraded core and the verification that functional grading …

Dynamic Electromechanical Characterization Of Ferroelectrics At Cryogenic Temperatures, William Kent Hays

Masters Theses

"Electromechanical coupling in ferroelectric materials has given rise to a myriad of technological applications. Through the complex domain structure of ferroelectrics materials, which are typically stiff and have low damping, can exhibit significant structural damping. The applications for a material with a relatively large Young’s modulus and the ability to damp out vibrations would be useful for structures, more specifically, aerospace structures. The dynamic mechanical properties of ferroelectrics, particularly mechanical properties while an electric field is applied, are not well understood. This is due in part to the lack of experimental methods to measure such properties. Even with recent advancements …