Mechanical Engineering Commons^™

Test 2206: Challenger Mt740, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2201: John Deere 6195r Autoquad-Plus, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Human Powered Vehicle Frame Design, Analysis, Manufacturing, And Testing, Christopher Reed, Kole W. Williams

Williams Honors College, Honors Research Projects

The University of Akron Human Powered Vehicle Design Team began this academic year with a mission to create a practical, lightweight, safe, and efficient human powered vehicle. The main objectives of ZC18 were inspired by competition in the 2018 Human Powered Vehicle Challenge at ASME E-Fest East. In addition to adhering to the rules of this competition, scoring high on the submitted reports, and competing well in the racing events, the team set a goal to assist in furthering knowledge related to the topic of human powered vehicles.

ZC18 was constructed nearly completely in the University of Akron’s Design Center …

Swagelok Adjustable Check Valve Setting Device, Brandon Sours, Paul Olson, David Race, Nick Rimpf

Williams Honors College, Honors Research Projects

Check valves are used to control the amount of flow through a valve and only open when a certain pressure is reached. The path of the fluid is strictly in one direction, which allows the valve to prevent any back flow within a system. They are also one of few self-automated piping system components that do not require assistance to open or close. Some check valves use a combination spring-and-nut compression assembly to set an opening pressure. As the nut is used to set the spring compression, and by extension the opening pressure, problems tend to arise when adjusting the …

Design Of Shape-Conforming Nosecone For Optimal Fluid Flow From Transonic To Supersonic Range, Anna Tombazzi

Williams Honors College, Honors Research Projects

Modern flight vehicles, such as rockets, missiles, and airplanes, experience a force caused by forebody wave drag during the flight. This drag force is induced when the frontal point of each vehicle breaks the pressure wave during flight. Efforts to reduce this wave drag force to improve flight efficiency include modifying the nosecone profile of the flight vehicles to lower the drag force.

This project revolved around creating a design to make the transformation of nosecone shapes from a ¾ Parabolic profile to a ½ Power Series profile possible, mid-flight. Using a novel nosecone assembly, shape memory alloys (SMAs) and …

Galvanic And Pitting Corrosion Of A Fastener Assembly, Julie Shallman

Williams Honors College, Honors Research Projects

This research focuses on coupled galvanic/pitting corrosion of AA7075 when combined with stainless steel in a fastener assembly. A one-dimensional mathematical model of a well-mixed thin film electrolyte is developed to predict the damage profile of the AA7075 surface when its protective coating is damaged. The damage exposes the galvanic couple. A time dependent system of partial differential equations for potential, chloride concentration, aluminum ion concentration, and damage is developed and solved numerically. Two approaches to calculate the current density within aluminum pits are discussed. The first is a current balance between the cathodic, anodic and passive portions of the …

Dynamic Mechanical Analysis Piezoelectric Design, Letia Bass, Michaela N. Mccrae, Ethan W. Goodman, Joesph W. Mazur

Williams Honors College, Honors Research Projects

This project is a continuation into the design and implementation of a Dynamic Mechanical Analysis (DMA) device that will be used to conduct high frequency testing on tire tread compounds. The design requirements necessary were to design a device that will produce a target frequency of 10 kHz with a 0.05% strain, while being at room temperature. The 3-D model developed by the previous year’s students was improved upon and new parts were designed as well. The assemblies (most importantly the connector piece) were 3-D modeled using Creo Parametric and analyzed with COMSOL Multiphysics. A new design involving flexures was …

Enhancement Of Instruction Pamphlet Insertion Machine, Zachary Skraba, Colton Rentsch, Brad Ruhaak, Abdulwahab Almuhwish, Faris Almulhim

Williams Honors College, Honors Research Projects

For this project, we were tasked with improving the current operation of a pamphlet insertion machine for Weaver Industries. Located in Cuyahoga Falls, Ohio, Weaver Industries is a company whose mission is to “maximize the independence and personal fulfillment of individuals with disabilities.” The main operation of the prototype is to assist the handicapped operator by automating the process for one of their products, a “Kong” dog toy. Currently, the workers manually insert each pamphlet into the cardboard packaging by hand. Over the past three years, there have been three separate design groups tasked with building and improving upon each …

Mht Assembly Line, Sean Lundholm

Williams Honors College, Honors Research Projects

The purpose of this report is to record the process followed and steps taken to design and implement a new product assembly line. While the implementation of the line required more than what is in this report, the projects outlined are those I was personally involved in and responsible for. This report will outline why the project was required, the steps taken to complete the project, and the challenges faced. Throughout the progression of the project, many different parts and areas were considered. As each of these was brought into focus, new challenges presented themselves and were dealt with accordingly. …

Sandia Senior Design Collaboration: Vacuum Sensor Design, James L. Valerio, Eric J. Black, Joseph P. Bednarz, David R. Warther

Williams Honors College, Honors Research Projects

Sandia National Laboratories has requested a fully mechanical device to close a circuit after launch has occurred and the device enters a vacuum. Intended for applications in rockets and missiles, the device must fit in a 36 degree wedge with a 6.8 inch radius that is 6 inches in height and be ready to bolt onto a rocket. The pressure switch must be prevented from actuating until a launch acceleration ranging from 20 to 27g is detected. The pressure switch must close the circuit after a pressure of 10^-1 Torr is reached and before a pressure of 10^{-6 …}

Evaluating Augmented Reality For Space Telerobotics Training, John Karasinski

Link Foundation Modeling, Simulation and Training Fellowship Reports

Despite the extensive previous research into manual tracking, to the author’s knowledge there exists no study in the literature addressing human performance or workload changes in manual tracking tasks between traditional computer monitors and mobile, augmented reality headsets. The aim of this study was to investigate the effect of several factors on human performance and workload in a three-axis manual tracking task. Recent advances in computing hardware have enabled a new generation of augmented reality stereoscopic devices, such as the Microsoft HoloLens, which have yet to be evaluated in the literature. The Microsoft HoloLens provides depth cues to the user …

Fabrication And Characterizations Of Lagp/Peo Composite Electrolytes For All Solid-State Lithium-Ion Batteries, Jeremy J. Lee

Browse all Theses and Dissertations

With the rise of electric vehicles and increasing dependence on mobile electronics, the demands for lithium-ion batteries have followed in tandem for their high energy and power densities. However, traditional lithium-ion batteries consisting of liquid electrolytes have limited operating temperatures and are susceptible to ignition and subsequent fires. Recently, battery research has diverged into solid state chemistry to address the aforementioned issues. In this research, we systematically investigate a series of ceramic/polymer lithium-ion conducting composite electrolytes, i.e. Li1.4Al0.4Ge1.6(PO4)3 /lithiated polyethylene oxide (LAGP/PEO). Lithiated PEO was prepared with two different lithium salts, LiBF4 and LITFSI. The impacts of the LAGP on …

Development And Thermal Management Of A Dynamically Efficient, Transient High Energy Pulse System Model, Nathaniel J. Butt

Browse all Theses and Dissertations

As technology advances, the abilities of civilian and military vehicles, both air and ground, will undoubtedly increase as well. One of the main areas of improvement is in the electronics area. The new electronics are ever smaller, use ever higher amounts of electrical power, and require ever smaller temperature tolerances. This leads to the problem of effectively managing the increasing thermal loads and temperature tolerances on these systems. One electronic system that causes concern is a high energy pulse system (HEPS). These devices have very high thermal loads (100s of kW). On an air vehicle, where thermal management by legacy …

Identification Of Nonlinear Constitutive Properties Of Damping Coatings, Mackenzie E. Tidball

Browse all Theses and Dissertations

Scheduled and unscheduled maintenance actions are a significant cost for gas turbines. Advanced life prediction capabilities help to mitigate these costs. However, the protective thermal and damping coatings applied to the turbine rotors which can help significantly extend component life simultaneously increase the difficulty of modeling the behavior of the components due to the nonlinearity they introduce.This research approaches modeling and analysis of nonlinear coatings for turbine blades and blisks using a nonlinear constitutive law model for the coating. The theoretical frequency response of the nonlinear system is solved for using the harmonic balance method. The coefficients of the nonlinear …

Fabrication And Characterizations Of Lithium Aluminum Titanate Phosphate Solid Electrolytes For Li-Based Batteries, Anurag Yaddanapudi

Browse all Theses and Dissertations

Demands for electric vehicles and flexible electronics have escalated research in developing high-performance lithium batteries based on solid-state chemistry. The present work is to develop highly-conductive and flexible solid electrolyte for such applications. Lithium aluminum titanate phosphate (LATP or Li1.3Al0.3Ti1.7(PO4)3), both in ceramic pellets and free-standing composite membranes, have been fabricated. The crystal structure, surface morphology, and ionic conductivity are systematically studied. LATP pellets are prepared using solid state reaction approach. The results indicate that calcine temperature has significant impacts on the phase impurity and sintering temperature and duration have more impacts on the grain size and porosity of LATP …

Layer-To-Layer Physical Characteristics And Compression Behavior Of 3d Printed Acrylonitrile Butadiene Styrene Metastructures Fabricated Using Different Process Parameters, Sivani Patibandla

Browse all Theses and Dissertations

Three-dimensional (3D) printing, a subset of additive manufacturing, is currently being explored heavily for actual part fabrication due to its ability to create complex objects with intricate internal features. There are several 3D printing technologies; however, the extrusion-based technology such as fused deposition modeling (FDM) is the widely used one owing to its low cost. The FDM method can be used to fabricate parts with different fill densities, fill patterns, and process parameters such as extruder temperature and print speed. In this research, influence of process parameters such as extruder temperature and speed on the physical characteristics such as the …

Constitutive Modeling Of Creep In Leaded And Lead-Free Solder Alloys Using Constant Strain Rate Tensile Testing, Eric Thomas Stang

Browse all Theses and Dissertations

Environmental and safety concerns have necessitated a phase-out of lead-based alloys, which are often used in electronics solder applications. In order to properly assess suitable replacement materials, it is necessary to understand the deformation mechanisms relevant to the application. In the case of electronics solder, creep is an important mechanism that must be considered in the design of reliable devices and systems. In this study, Power-Law and Garofalo constitutive creep models were derived for two medium temperature solder alloys. The first alloy is known by the commercial name Indalloy 236 and is a quaternary alloy of lead, antimony, tin, and …

Experimental Investigation Of Impinged Droplet Dynamics, Nitisha Ahuja

Dissertations, Master's Theses and Master's Reports

The fuel spray wall interaction phenomenon plays an essential role in determining the emissions and performance of an internal combustion engine. The investigation of single droplet wall interaction is crucial to understanding of a spray wall impingement process. This report is a compilation of the experimental work done to understand the droplet impingement characteristics, through optical diagnostics and temperature measurement. Different fuels and different surface under ambient and elevated temperature conditions are used for these tests, with two objectives: Development of a common depositionsplashing criteria; and Understanding droplet post impingement dynamics variation with factors like: Weber number (ratio of inertia …

Optimization And Control Of An Array Of Wave Energy Converters, Jianyang Lyu

Dissertations, Master's Theses and Master's Reports

This study explored optimal configuration of both the array layout and the dimension of each WEC in the array. The array contains heaving buoys with full interaction and exact hydrodynamics. Optimization of dimension was done on each WEC in the array with a given optimal layout, and a higher q-factor was achieved. Both impedance matching optimal control and derivative control were employed, which provides both theoretical maximum energy and a more realistic case. Then the work was expanded to optimization of both the array layout and the dimension of each WEC in the array. An average of 39.21% higher q-factor …

Development Of Novel Models To Study Deep Brain Effects Of Cortical Transcranial Magnetic Stimulation, Farheen Syeda

Theses and Dissertations

Neurological disorders require varying types and degrees of treatments depending on the symptoms and underlying causes of the disease. Patients suffering from medication-refractory symptoms often undergo further treatment in the form of brain stimulation, e.g. electroconvulsive therapy (ECT), transcranial direct current stimulation (tDCS), deep brain stimulation (DBS), or transcranial magnetic stimulation (TMS). These treatments are popular and have been shown to relieve various symptoms for patients with neurological conditions. However, the underlying effects of the stimulation, and subsequently the causes of symptom-relief, are not very well understood. In particular, TMS is a non-invasive brain stimulation therapy which uses time-varying magnetic …

Flow Patterns Through Vascular Graft Models With And Without Cuffs, Chia Min Leong, Gary B. Nackman, Timothy Wei

Department of Mechanical and Materials Engineering: Faculty Publications

The shape of a bypass graft plays an important role on its efficacy. Here, we investigated flow through two vascular graft designs±with and without cuff at the anastomosis. We conducted Digital Particle Image Velocimetry (DPIV) measurements to obtain the flow field information through these vascular grafts. Two pulsatile flow waveforms corresponding to cardiac cycles during the rest and the excitation states, with 10% and without retrograde flow out the proximal end of the native artery were examined. In the absence of retrograde flow, the straight end-to-side graft showed recirculation and stagnation regions that lasted throughout the full cardiac cycle with …

Dislocations Interaction Induced Structural Instability In Intermetallic Al2cu, Qing Zhou, Jian Wang, Amit Misra, Ping Huang, Fei Wang, Kewei Xu

Department of Mechanical and Materials Engineering: Faculty Publications

Intermetallic precipitates are widely used to tailor mechanical properties of structural alloys but are often destabilized during plastic deformation. Using atomistic simulations, we elucidate structural instability mechanisms of intermetallic precipitates associated with dislocation motion in a model system of Al₂Cu. Interaction of non-coplanar <001> dislocation dipoles during plastic deformation results in anomalous reactions—the creation of vacancies accompanied with climb and collective glide of <001> dislocation associated with the dislocation core change and atomic shuffle—accounting for structural instability in intermetallic Al₂Cu. This process is profound with decreasing separation of non-coplanar dislocations and increasing temperature and is likely to be …

Mechanical Performance Of Plla Stent, Longzhen Wang, Junfei Tong, Pengfei Dong, David L. Wilson, Hiram G. Bezerra, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Stent implantation is widely used to treat blocked lumen. Stents were meshed structure made of polymers and metal alloys, including stainless steel, cobalt chrome and nitinol [1]. Clinical studies had demonstrated that stents helped to scaffold the diseased lesion up to one year when tissue adapted to the stented environment [2]. However, the permanently implanted stents inside artery were associated with complications such as stent fracture, tissue inflammation, in-stent restenosis and thrombosis [3]. Currently, biodegradable stents are attracting more attention due to its potential long-term efficacy in treating blocked lumens. The detailed characterizations of biodegradable stents are essential for the …

Plaque Burden Influences Accurate Classification Of Fibrous Cap Atheroma By In-Vivo Optical Coherence Tomography In A Porcine Model Of Advanced Coronary Atherosclerosis., Christian B. Poulsen, Ryan M. Pedrigi, Nilesh Pareek, Ismail D. Kilic, Niels R. Holm, Jacob F. Bentzon, Hans Erik Botker, Erling Falk, Rob Krams, Ranil De Silva

Department of Mechanical and Materials Engineering: Faculty Publications

Advanced coronary atherosclerosis assessed by in-vivo optical coherence tomography (OCT) has not been directly compared with histology. In a porcine model with human-like coronary atherosclerosis we compared in-vivo OCT images with histology in five animals. We found a high sensitivity but modest specificity of OCT in classifying fibrous cap atheroma (FCA). The modest specificity was caused by misclassification of FCA lesions as pathological intimal thickening. The misclassification most frequently occurred when plaque burden exceeded ~20%. Compared with histology, OCT has high sensitivity but modest specificity for identifying FCA. The study suggests that plaque burden should be considered when interpreting OCT …

Multifunctional Operational Component For Robotic Devices, Shane M. Farritor, Amy Lehman, Mark Rentschler

Department of Mechanical and Materials Engineering: Faculty Publications

The various embodiments disclosed herein relate to modular medical devices, including various devices with detachable modular components and various devices with pivotally attached modular components. Additional embodiments relate to procedures in which various of the devices are used cooperatively. Certain embodiments of the medical devices are robotic in vivo devices.

Scaffold Structural Microenvironmental Cues To Guide Tissue Regeneration In Bone Tissue Applications, Xuening Chen, Hongyuan Fan, Xiaowei Deng, Lina Wu, Tao Yi, Linxia Gu, Changchun Zhou, Yujiang Fan, Xingdong Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

In the process of bone regeneration, new bone formation is largely affected by physico-chemical cues in the surrounding microenvironment. Tissue cells reside in a complex scaffold physiological microenvironment. The scaffold should provide certain circumstance full of structural cues to enhance multipotent mesenchymal stem cell (MSC) differentiation, osteoblast growth, extracellular matrix (ECM) deposition, and subsequent new bone formation. This article reviewed advances in fabrication technology that enable the creation of biomaterials with well-defined pore structure and surface topography, which can be sensed by host tissue cells (esp., stem cells) and subsequently determine cell fates during differentiation. Three important cues, including scaffold …

Heat Transfer Across A Nanoscale Pressurized Air Gap And Its Application In Magnetic Recording, Jinglin Zheng, Yung-Kan Chen, Qin Zhou

Department of Mechanical and Materials Engineering: Faculty Publications

In this study, we investigated how a thermally actuated air bearing slider heats up a fast-spinning storage disk through a highly pressurized nanoscale air gap in a magnetic recording system. A Euleriandescription- based computational approach is developed considering heat conduction through a pressurized air film and near-field radiation across the gap. A set of field equations that govern the air bearing dynamics, slider thermo-mechanics and disk heat dissipation are solved simultaneously through an iterative approach. A temperature field on the same order as the hot slider surface itself is found to be established in the disk. The effective local heat …

Interfacial Characterization By Pull-Out Test Of Bamboo Fibers Embedded In Poly(Lactic Acid), Quentin Viel, Antonella Esposito, Jean-Marc Saiter, Carlo Santulli, Joseph A. Turner

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, the apparent shear strength at the interface between a bamboo fiber and the surrounding poly(lactic acid) (PLA) matrix is quantified. A method for processing pull-out test samples within a controlled embedded length is proposed and the details of the test procedure are presented, along with a critical discussion of the results. Two series of samples are considered: untreated and mercerized bamboo fibers from the same batch, embedded in the same polyester matrix. Electron and optical microscopy are used to observe the fiber–matrix interface before and after the test, and to identify the failure mode of each sample, …

Complementary Microscopy Techniques Applied For Characterizing The Localized Nanoscale Structure Of Poly (Vinylidene Fluoride), Wen Qian, Shuo Sun, Charles Nguyen, Wenlong Li, Stephen Ducharme, Joesph A. Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Poly (vinylidenefluoride) (PVDF), a well-recognized electroactive polymer, has been studied extensively over many decades. Recently, there has been increasing interest in tuning the electrical properties of PVDF from ferroelectric to piezoelectric and to pyroelectric, which can be attained via controlling the microscale structure down to the nanoscale structure [1-2]. To optimize the preparation conditions of PVDF and its copolymers, as well as to improve the performance for many applications, comprehensive analytical techniques are of great importance. In this paper, we demonstrate complementary nanoscale characterization and measurement techniques, by conducting a systematic and coordinated study involving scanning electron microscopy (SEM), high …

Dynamic Rops Test For Tractors Over 6,000 Kilograms, Caleb M. Lindhorst, Roger M. Hoy, Santosh Pitla, Michael F. Kocher

Department of Agricultural and Biological Systems Engineering: Faculty Publications

OECD static tests (Codes 4, 6, 7, and 8) for agricultural rollover protective structures (ROPS) have become accepted standards for evaluating the ability of these structures to protect the operator during tractor rollover events. The strength properties of some materials typically used in ROPS change because of cold weather embrittlement at low temperatures. The static ROPS tests lack the ability to evaluate the strength of these structures during cold weather. The use of the dynamic ROPS test is well noted as a means for proving cold weather embrittlement resistance properties. Unfortunately, application of the OECD dynamic ROPS test (Code 3) …