Mechanical Engineering Commons^™

Energy-Efficient And -Economic Technologies For Vapor Compression Refrigeration Systems: A Comprehensive Review., Xiaohui She, Lin Cong, Binjian Nie, Guanghui Leng, Hao Peng, Yi Chen, Xiaosong Zhang, Tao Wen, Hongxing Yang, Yimo Luo

Faculty of Science & Technology (THEi)

Vapor Compression Refrigeration Systems (VCRS) are widely used to provide cooling or freezing for domestic/office buildings, supermarkets, data centres, etc., which expend 15% of globally electricity and contribute to ∼10% of greenhouse gas emissions globally. It is reported that cooling demand is expected to grow tenfold by 2050. Therefore, it is critical to improve the efficiency of the VCRS. In this paper, a comprehensive review of advanced and hot technologies is conducted for the VCRS. These technologies include radiative cooling, cold energy storage, defrosting and frost-free, temperature and humidity independent control (THIC), ground source heat pump (GSHP), refrigerant subcooling, and …

Investigation On The Regeneration And Corrosion Characteristics Of An Anodized Aluminum Plate Regenerator., Tao Wen, Lin Lu, Hongxing Yang, Yimo Luo

Faculty of Science & Technology (THEi)

The traditional vapor compression cooling system (VCS) has been criticized for its heavy reliance on electricity consumption and limited control ability of humidity. Compared with the VCS, the liquid desiccant cooling system (LDCS) is more efficient by handling the sensible and latent load separately. The present study investigated the regeneration and corrosion characteristics of an anodized aluminum plate regenerator for the first time. Comparative tests were conducted to present the regeneration and corrosion characteristics of the normal and anodized regenerator. The influence of internal heating on the regeneration performance was also identified. The results showed that the corrosion rate was …

Investigation On The Regeneration Performance Of Liquid Desiccant By Adding Surfactant Pvp-K30., Tao Wen, Lin Lu, Chuanshuai Dong, Yimo Luo

Faculty of Science & Technology (THEi)

The liquid desiccant cooling system (LDCS) is a promising alternative for the conventional vapor compression system due to its high energy efficiency. To enhance the mass transfer between the regeneration air and liquid desiccant in the regenerator, the paper firstly introduced a kind of surfactant called polyvinyl pyrrolidone (PVP-K30) which was added into the LiCl solution for better desiccant regeneration performance. The falling film characteristics and regeneration performance were investigated and compared with and without surfactant. The results indicated that the contact angle of desiccant solution on plate decreased from 58.5° to 28.0° by adding surfactant with 0.4% of concentration. …

Decoupling Of Second-Order Linear Systems By Isospectral Transformation, Daniel Kawano, Rubens Salsa, Fai Ma

Faculty Publications - Mechanical Engineering

No abstract provided.

Mechanical And Aerospace Engineering, 2017-2018, College Of Engineering And Applied Sciences

Mechanical and Aerospace Engineering News

• Letter from the Chair
• Introducing Dr. Jinseok Kim
• Use of 3D Printing at WMU Helps Borgess Cardiologist Plug Holes in the Heart
• Department of Mechanical and Aerospace Engineering Develops Semi-Virtual Reality Powered Wheelchair Simulator
• The Western Aerospace Launch Initiative (WALI)
• 2017 NSF I-Corps Experience of MAE team
• Matthew Baird's Internship Experiences at JPL and GRC
• More Department News
• Faculty Sabbaticals

Comparative Study Of The Microstructure And Mechanical Properties Of Mechanically Alloyed And Spark Plasma Sintered Alxcocrfeni (0≤X≤2)High Entropy Alloys, David Mikhail

Undergraduate Research Posters 2018

High entropy alloys are a new class of material systems that have promising potential in high temperature structural applications. Mechanical alloying (MA) has gained special attention as a powerful non-equilibrium process for fabricating amorphous and nanocrystalline materials, whereas spark plasma sintering (SPS) is a unique technique for processing dense and near net shape bulk alloys with homogenous microstructure. This research paper discusses novel mechanically alloyed followed by spark plasma sintering approach for assessing composition-microstructure-microhardness relationship in AlxCoCrFeNi (0≤x≤2) high entropy alloy as a candidate system. With increasing Al content, there was a gradual change from a fcc-based microstructure to a …

Decoupling Of Second-Order Linear Systems By Isospectral Transformation, Daniel Kawano, Rubens Salsa, Fai Ma

Faculty Publications - Mechanical Engineering

No abstract provided.

Numerical Modeling And Control Of Solids Separation Using Continuously Moving Fine Mesh Filters, Anthony Sherratt, Christopher T. Degroot, Anthony G. Straatman, Domenico Santoro

Mechanical and Materials Engineering Publications

No abstract provided.

The Development And Numerical Modelling Of A Representative Elemental Volume For Packed Sand, Ashraf Thabet, Anthony G. Straatman

Mechanical and Materials Engineering Publications

No abstract provided.

A Porous Media Model Of Alveolar Duct Flow In The Human Lung, Anthony G. Straatman, Christopher T. Degroot

Mechanical and Materials Engineering Publications

No abstract provided.

Human Activity Tracking And Recognition Using Kinect Sensor, Roanna Lun

ETD Archive

The objective of this dissertation research is to use Kinect sensor, a motion sensing input device, to develop an integrated software system that can be used for tracking non-compliant activity postures of consented health-care workers for assisting the workers' compliance to best practices, allowing individualized gestures for privacy-aware user registration, movement recognition using rule-based algorithm, real-time feedback, and exercises data collection. The research work also includes developing a graphical user interface and data visualization program for illustrating statistical information for administrator, as well as utilizing cloud based database system used for data resource.

Non-Intrusive Optical Measurement Of Electron Temperature In Near Field Plume Of Hall Thruster, Peter J. Urban

ETD Archive

Currently there is a large interest in the use of more efficient means of propulsion in long term missions due to the costs and difficulties associated with placing and maintaining the needed fuel for conventional chemical systems in orbit. Mass reduction of upper stages will return large returns due to the great reduction in required lower stage fuel. Due to these factors, alternatives are undergoing active research, though this paper is concerned with the area of electrical propulsion. Electric propulsion is broadly defined as propulsion where the energization of the exhaust occurs via application of electromagnetic fields as opposed to …

Neuromuscular Reflex Control For Prostheses And Exoskeletons, Sandra K. Hnat

ETD Archive

Recent powered lower-limb prosthetic and orthotic (P/O) devices aim to restore legged mobility for persons with an amputation or spinal cord injury. Though various control strategies have been proposed for these devices, specifically finite-state impedance controllers, natural gait mechanics are not usually achieved. The goal of this project was to invent a biologically-inspired controller for powered P/O devices. We hypothesize that a more muscle-like actuation system, including spinal reflexes and vestibular feedback, can achieve able-bodied walking and also respond to outside perturbations. The outputs of the Virtual Muscle Reflex (VMR) controller are joint torque commands, sent to the electric motors …

Predictive Simulations Of Gait And Their Application In Prosthesis Design, Anne D. Koelewijin

ETD Archive

Predictive simulations predict human gait by solving a trajectory optimization problem by minimizing energy expenditure. These simulations could predict the effect of a prosthesis on gait before its use. This dissertation has four aims, to show the application of predictive simulations in prosthesis design and to improve the quality of predictive simulations. Aim 1 was to explain joint moment asymmetry in the knee and hip in gait of persons with a transtibial amputation (TTA gait). Predictive simulations showed that an asymmetric gait required less effort. However, a small effort increase yielded a gait with increased joint moment symmetry and reduced …

An Anisotropic Constitutive Model For Nuclear Grade Graphite, James Christopher

ETD Archive

Graphite material is used extensively in nuclear reactors however the material has a limited strain range for elastic behavior. This provides the motivation to derive a constitutive model that captures the inelastic deformations exhibited by this material. This dissertation first presents details of an isotropic constitutive model derived using continuum principles of engineering mechanics that accounts for different inelastic behavior in tension and compression. An inelastic dissipation function was developed using an integrity basis proposed by Green and Mkrtichian (1977) for the isotropic version of the model. This isotropic model was then extended to capture anisotropic stress-strain behavior using directional …

An Integrated Microstructural-Nanomechanical-Chemical Approach To Examine Material-Specific Characteristics Of Cementitious Interphase Regions, Mahdieh Khedmati, Yong-Rak Kim, Joseph A. Turner, Hani Alanazi, Charles Nguyen

Department of Mechanical and Materials Engineering: Faculty Publications

Effective properties and structural performance of cementitious mixtures are substantially governed by the quality of the interphase region because it acts as a bridge transferring forces between aggregates and a binding matrix and is generally susceptible to damage. As alternative binding agents like alkali-activated precursors have obtained substantial attention in recent years, there is a growing need for fundamental knowledge to uncover interphase formation mechanisms. In this paper, two different types of binding materials, i.e., fly ash-based geopolymer and ordinary portland cement, were mixed with limestone aggregate to examine and compare the microstructures and nanomechanical properties of interphase region. To …

Methods, Systems, And Devices For Surgical Access And Procedures, Shane M. Farritor, Mark Rentschler, Amy Lehman, Stephen R. Platt, Jeff Hawks

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components, including components that can be incorporated into robotic and/or in vivo medical devices. Certain embodiments include various actuation system embodiments, including fluid actuation systems, drive train actuation systems, and motorless actuation systems. Additional embodiments include a reversibly lockable tube that can provide access for a medical device to a patient's cavity and further provides a reversible rigidity or stability during operation of the device. Further embodiments include various operational components for medical devices, including medical device arm mechanisms that have both axial and rotational movement while maintaining a relatively compact …

Excess Charge-Carrier Induced Instability Of Hybrid Perovskites, Yuze Lin, Bo Chen, Yanjun Fang, Jingjing Zhao, Chunxiong Bao, Zhenhua Yu, Yehao Deng, Peter N. Rudd, Yanfa Yan, Yongbo Yuan, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Identifying the origin of intrinsic instability for organic–inorganic halide perovskites (OIHPs) is crucial for their application in electronic devices, including solar cells, photodetectors, radiation detectors, and light-emitting diodes, as their efficiencies or sensitivities have already been demonstrated to be competitive with commercial available devices. Here we show that free charges in OIHPs, whether generated by incident light or by current-injection from electrodes, can reduce their stability, while efficient charge extraction effectively stabilizes the perovskite materials. The excess of both holes and electrons reduce the activation energy for ion migration within OIHPs, accelerating the degradation of OIHPs, while the excess holes …

Hierarchical Hybrid Architectures For Robust And Reusable Nano-Devices, Sharmila M. Mukhopadhyay

Mechanical and Materials Engineering Faculty Publications

No abstract provided.

A New Capacity Controller For A Direct Expansion Air Conditioning System For Operational Safety And Efficiency., Yudong Xia, Huaxia Yan, Shiming Deng, Ming-Yin Chan

Faculty of Science & Technology (THEi)

For achieving a balance between the operational safety and efficiency of a variable speed direct expansion air conditioning system, a new capacity controller that can not only simultaneously control indoor air temperature and humidity, but also select an optimized degree of superheat setting to properly balance the operational safety and efficiency has been developed, by adding a control module to a previously developed capacity controller. The core of the control module was an artificial neural network based model representing the known relationship between the inherent operational characteristics and operational stability of a variable speed direct expansion air conditioning system. Using …

Investigation On Solar Assisted Liquid Desiccant Dehumidifier And Evaporative Cooling System For Fresh Air Treatment., Yi Chen, Hongxing Yang, Yimo Luo

Faculty of Science & Technology (THEi)

The widely used semi-centralized air conditioning (A/C) system consisting of independent fresh air system and fan coil system suffers from huge energy consumption, especially for fresh air treatment. Therefore, a liquid desiccant dehumidifier and regenerative indirect evaporative cooling (LDD-RIEC) system is proposed for fresh air treatment. The fresh air is handled by the LDD-RIEC system in which no electricity-intensive compressor involves. The hot and humid fresh air is firstly dehumidified by LDD and then sensibly cooled by RIEC. The thermal energy captured by solar collectors is used for desiccant solution regeneration. Indoor return air is cooled by fan coils of …

Development And Experimental Study Of A Novel Plate Dehumidifier Made Of Anodized Aluminum., Tao Wen, Lin Lu, Chuanshuai Dong, Yimo Luo

Faculty of Science & Technology (THEi)

The falling film dehumidifier is a key component in the liquid desiccant cooling system (LDCS). However, the most commonly used metals, such as steel and aluminum, can hardly resist the erosion of liquid desiccant. It greatly limits the fabrication of compact dehumidifiers and hinders the promotion of LDCS. The present study introduced a novel falling film dehumidifier which was made by the metal of anodized aluminum. Experiments were carried out to compare the dehumidification performance between ordinary aluminum dehumidifier and anodized one. The influences of air temperature, mass flow rate, inlet humidity and solution temperature, mass flow rate, temperature on …

Visible Light Crosslinkable Human Hair Keratin Hydrogels, Kan Yue, Yanhui Liu, Batzaya Byambaa, Vaishali Singh, Wanjun Liu, Xiuyu Li, Yunxia Sun, Yu Shrike Zhang, Ali Tamayol, Peihua Zhang, Kee Woei Ng, Nasim Annabi, Ali Khademhosseini

Department of Mechanical and Materials Engineering: Faculty Publications

Keratins extracted from human hair have emerged as a promising biomaterial for various biomedical applications, partly due to their wide availability, low cost, minimal immune response, and the potential to engineer autologous tissue constructs. However, the fabrication of keratin-based scaffolds typically relies on limited crosslinking mechanisms, such as via physical interactions or disulfide bond formation, which are time-consuming and result in relatively poor mechanical strength and stability. Here, we report the preparation of photocrosslinkable keratin-polyethylene glycol (PEG) hydrogels via the thiol-norbornene “click” reaction, which can be formed within one minute upon irradiation of visible light. The resulting keratin-PEG hydrogels showed …

Performance Trades For Multiantenna Gnss Multisensor Attitude Determination Systems, Nathan A. Tehrani, Jason N. Gross

Faculty & Staff Scholarship

We present various performance trades for multiantenna global navigation satellite system (GNSS) multisensor attitude estimation systems. In particular, attitude estimation performance sensitivity to various error sources and system configurations is assessed. This study is motivated by the need for system designers, scientists, and engineers of airborne astronomical and remote sensing platforms to better determine which system configuration is most suitable for their specific application. In order to assess performance trade-offs, the attitude estimation performance of various approaches is tested using a simulation that is based on a stratospheric balloon platform. For GNSS errors, attention is focused on multipath, receiver measurement …

Further Development Of A Thermal Comfort Based Fuzzy Logic Controller For A Direct Expansion Air Conditioning System, Huaxia Yan, Yan Pan, Zhao Li, Shiming Deng

Faculty of Science & Technology (THEi)

The primary purpose of A/C is offering occupants with acceptable indoor thermal comfort levels. Thermal comfort is a complicated result of non-linear interactions between six parameters. However, many of current A/C systems solely control air temperature. Whenever anyone of the five parameters other than temperature varies significantly, an occupant may feel thermally uncomfortable. To address the issue, a comprehensive thermal comfort index should be used as regulator in A/C systems. One fuzzy logic controller is available. However, the approach to the fuzzy logic controller is complicated. In this paper, one previous established fuzzy logic controller is simplified for its real …

Exercise Machine Generator, Duane Harbick

All Undergraduate Projects

Exercise “spinning bikes” and bicycle training stands are common ways to maintain fitness and train for cycling. This exercise necessitates the user putting work into the machine by means of pedaling. In many instances the work put into exercise bikes and training stands is not taken advantage of. The objective of this project is an attempt to make use of some of the energy that a person would usually expend during exercise by building a generator that interfaces with multiple spinning bikes and training stands. It uses a synchronous pulley system to interface with the exercise machine and spin a …

Asme Rc Baja Challenge: Suspension And Steering, Hunter W. Jacobson

All Undergraduate Projects

The American Society of Mechanical Engineers (ASME) usually hosts an RC Baja challenge each year, testing a RC car in three events: slalom, acceleration and Baja. Although ASME will not be holding an event this year, CWU will be holding a similar event with three RC Baja car teams from CWU. The RC car that is tested in these events is designed and manufactured typically in teams of two. The RC car that each team submits must be able to complete these events while also remaining competitive. One part of great importance for the RC car is the suspension and …

Easy Install Outboard Motor Mount, Doug Dunbar

All Undergraduate Projects

The boating industry can be expensive for the typical weekend boater. That is, keeping, maintaining, and using a boat and all of its various accessories is a constant cost for the owner. In the Midwest and inland it is necessary to store boats and outboard boat motors out of the inclement weather and harsh conditions of seasonal change. Specifically, removing or installing an expensive and awkward outboard motor can be both dangerous financially and physically (damage or injury). It is not uncommon for motors to cost several thousand dollars.

The purpose of this project was to research, design, and implement …

Cwu Bottle Opener Manufacturing, Austin Sanford

All Undergraduate Projects

Previous students from the Mechanical Engineering Technology program came up with a method to help raise funds and awareness for the program. The idea was to manufacture and sell CWU bottle openers. However, a more efficient manufacturing method was needed. The aspect of the process that would have the most impact on the manufacturing time and material efficiency was the CNC machining of the parts. There were many potential variables to change to improve the process, but the main changes were to the cutter speeds and stock material size. Consequently, the changes made to stock material size reduced the number …

Asme R/C Baja Car, Torrie Large

All Undergraduate Projects

How does one build a car? Do they start with the tires and build inward or do they develop separate aspects at the same time? This remote-controlled car was designed and built with the intention of competing in the annual Baja Competition. There are three competitions: sprinting, slalom, and an obstacle course. The suspension system of this car must be designed to support the car for both the physical build and the competitiveness. It must do this without interfering with the drive train and steering mechanism designed by Doug Erickson. The suspension system employs suspension arms attached to the chassis …