Mechanical Engineering Commons^™

Enhancing Mobility And Independence Of Wheelchair Users, Briar Blake, Paul Nauleau

Interdisciplinary Design Senior Theses

Conditions as simple as a leg fracture or more severe impairments such as paralysis and stroke may confine a person to a wheelchair. Wheelchairs help people with limited mobility transport themselves to different locations, but do not help the person leave the wheelchair. Users would need to do this to enter a car, use the restroom, take a shower, and sit at a table comfortably with family. The following design is a wheelchair attachment that serves to provide the user with increased mobility and independence. Wheelchair users struggle to get into and out of their chairs due to the unassisted …

Art To Engineering: Curved Folding And Developable Surfaces In Mechanism And Deployable Structure Design, Todd G. Nelson

Theses and Dissertations

This work investigates how curved-crease origami and the developable surfaces which compose it can be transitioned to engineering design. Methods for creating flexible, tailorable-property surfaces that function as thick panels in place of paper are presented. Concepts from curved-crease origami and developable surfaces that can describe and extend engineering applications are discussed and demonstrated. These concepts are particularly beneficial to applications where curved surfaces are integral to the function, deployability is desired, and planar manufacturing could be beneficial.The first part of this work uses arrays of compliant elements to create flexible-tailorable property surfaces. The key feature to these arrays is …

Human Knee Fea Model For Transtibial Amputee Tibial Cartilage Pressure In Gait And Cycling, Gregory Lane

Master's Theses

Osteoarthritis (OA) is a debilitating disease affecting roughly 31 million Americans. The incidence of OA is significantly higher for persons who have suffered a transtibial amputation. Abnormal cartilage stress can cause higher OA risk, however it is unknown if there is a connection between exercise type and cartilage stress. To help answer this, a tibiofemoral FEA model was created. Utilizing linear elastic isotropic materials and non-linear springs, the model was validated to experimental cadaveric data. In a previous study, 6 control and 6 amputee subjects underwent gait and cycling experiments. The resultant knee loads were analyzed to find the maximum …

Mechanical Characterization Of Selectively Laser Melted 316l Stainless Steel Body Centered Cubic Unit Cells And Lattice Of Varying Node Radii And Strut Angle, Christopher James Hornbeak

Master's Theses

An experimental study of several variants of radius and strut angle of the body centered cubic unit cell was performed to determine the mechanical properties and failure mechanisms of the mesostructure. Quasi static compression tests were performed on an Instron® universal testing machine with a 50kN load cell at 0.2mm/min. The test samples were built using a SLM Solutions 125 selective laser melting machine with 316L stainless steel. Test specimens were based on 5mm cubic unit cells, with a strut diameter 10% of the unit cell size, with skins on top and bottom to provide a cantilever boundary constraint. Specimens …

Finite-Difference Modeling Of The Batch Process Smoldering Combustion Of Wastewater, Laura H. Kawashiri

Master's Theses

A MATLAB model was developed for the smoldering combustion of wastewater in the context of a decentralized residential wastewater treatment appliance. Data from a batch process sewage smoldering experiment was simulated using implicit finite-difference approximations, assuming one-dimensional transient conductive heat transfer. The time-dependent temperature profiles within the column represented the main parameters of interest and were used to verify recoverable heat energy estimations. Given that the modeling method used for this thesis represents a unique approach, the assumptions and limitations of this model are thoroughly described in the context of reproducing results for other smoldering setups. A lack of convergence …

Dynamics Simulation And Optimal Control Of A Multiple-Input And Multiple-Output Balancing Cube, Felix K. Haimerl

Master's Theses

This thesis document outlines the development of a multibody dynamics simulation of an actively stabilized multiple-input, multiple-output, coupled, balancing cube and the process of verifying the results by implementing the control algorithm in hardware. A non-linear simulation of the system was created in Simscape and used to develop a Linear Quadratic Gaussian control algorithm. To implement this algorithm in actual hardware, the system was first designed, manufactured, and assembled. The structure of the cube and the reaction wheels were milled from aluminum. DC brushless motors were installed into the mechanical system. In terms of electronics, a processor, orientation sensor, motor …

Thermal Modelling And Validation Of Heat Profiles In An Rf Plasma Micro-Thruster, Alec Sean Henken

Master's Theses

The need and demand for propulsion devices on nanosatellites has grown over the last decade due to interest in expanding nanosatellite mission abilities, such as attitude control, station-keeping, and collision avoidance. One potential micro-propulsion device suitable for nanosatellites is an electrothermal plasma thruster called Pocket Rocket. Pocket Rocket is a low-power, low-cost propulsion platform specifically designed for use in nanosatellites such as CubeSats. Due to difficulties associated with integrating propulsion devices onto spacecraft such as volume constraints and heat dissipation limitations, a characterization of the heat generation and heat transfer properties of Pocket Rocket is necessary. Several heat-transfer models of …

Application Of Brain-Based Learning Principles To Engineering Mechanics Education: Implementation And Preliminary Analysis Of Connections Between Employed Strategies And Improved Student Engagement, Firas Akasheh, John Solomon, Eric Hamilton, Chitra Nayak, Vimal Viswanathan

Faculty Publications, Mechanical Engineering

In a pilot study supported by NSF, an instructional model that uses brain based learning principles as instructional protocols has been developed and successfully implemented in the course Introduction to Fluid Mechanics at a HBCU. Motivated by that success, we extended a similar intervention to another course, Dynamics, in the same school. In this paper, we report preliminary data from this intervention. The main strategies implemented in this intervention include: organization of the course into specific concepts and sub-concepts, which are concisely presented by short (limited to 2-6 minutes) content-rich lectures (diagrams, animations, narrations), active learning through in-class worksheets, and …

A Study On The Student Success In A Blended-Model Engineering Classroom, Vimal Viswanathan, John Solomon

Faculty Publications, Mechanical Engineering

One of the primary concern that many engineering educators face is the lack of engagement of students in their classroom. While literature suggests a variety of factors that might negatively influence student engagement, the theory of “Tailored Instructions and Engineered Delivery Using Protocols” (TIED UP) specifically addresses the lack of engagement arising from a weak pre-requisite base. TIED UP is a blended teaching model where the content delivery follows a set of protocols inspired by the brain-based learning approach. In a typical TIED UP classroom, content delivery is performed using short, animated and scripted concept videos that are generated before …

Universal Airfoil Parametrization Using B-Splines, Dev Rajnarayan, Andrew Ning, Judd Mehr

Faculty Publications

In this paper, we apply well-known techniques for parametric curves to the definition and deformation of airfoil sections. While it has already been shown that many versions of Kulfan’s Class Shape Transformation (CST) are exactly equivalent to Bézier curves, we show here that all NACA 4-digit thickness distributions and the PARSEC parametrization of Sobiezcky are also higher-order Bézier curves. As with CST, Béziers and B-Splines provide direct control over aerodynamically meaningful features such as nose radius and boat-tail angle, but also provide more a intuitive parametrization of the rest of the airfoil surface. We show the efficacy of B-Spline-based parametrizations …

Modeling Of Cloud-Based Digital Twins For Smart Manufacturing With Mt Connect, Liwen Hu, Ngoc-Tu Nguyen, Wenjin Tao, Ming-Chuan Leu, Xiaoqing Frank Liu, Rakib Shahriar, S M Nahian Al Sunny

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The common modeling of digital twins uses an information model to describe the physical machines. The integration of digital twins into productive cyber-physical cloud manufacturing (CPCM) systems imposes strong demands such as reducing overhead and saving resources. In this paper, we develop and investigate a new method for building cloud-based digital twins (CBDT), which can be adapted to the CPCM platform. Our method helps reduce computing resources in the information processing center for efficient interactions between human users and physical machines. We introduce a knowledge resource center (KRC) built on a cloud server for information intensive applications. An information model …

Chemotherapeutic Drug Cytotoxicity Measurement With A 3d Biomimetic Microfluidic Device And Computational Fluid Dynamics Model, Maryam Moarefian, Caroline Jones, Luke Achenie, Danesh Tafti

Biology and Medicine Through Mathematics Conference

No abstract provided.

Kinetic Study Of Free Radical-Radical Reactions Of Combustion Importance At Elevated Pressures, Chao Yan

Dissertations

Combustion mechanisms consist of hundreds elementary reactions of free radicals and stable molecules. Radical-radical elementary reactions play important roles due to the high concentration in which free radicals are accumulated in combustion systems. Radical-radical reactions are typically multi-channel. Some of the channels might be of chain propagation or even chain branching nature, while other channels might be of chain termination nature. The relative importance of different channels is pressure dependent. Compared to radical-molecule reactions, radical-radical reactions are much less studied. This is due to the difficulties of well characterized quantitative production of radical species as well as due to the …

Microfluidic Biosensor With Functionalized Gold Nano Particles On Interdigitated Electrodes, Bharath Babu Nunna

Dissertations

The integration of the microfluidics to the biosensor has growing demand with favorable conditions such as reduced processing time and low reagent consumption. The immuno biosensing with the microfluidic platform helped to make the electrochemical biosensing assays portable due to which this sensing mechanism can be easily implemented in point of care devices. The implementation of the biosensing in the microchannels significantly reduces the sample requirement form milli liter (mL) to micro liter (uL), and thus leads to low volume sample requirement during the sensing. The primary factors contributing to the microfluidic biosensors performance are probe immobilization, specific binding and …

Experiments And Multi-Field Modeling Of Inelastic Soft Materials, Shuolun Wang

Dissertations

Soft dielectrics are electrically-insulating elastomeric materials, which are capable of large deformation and electrical polarization, and are used as smart transducers for converting between mechanical and electrical energy. While much theoretical and computational modeling effort has gone into describing the ideal, time-independent behavior of these materials, viscoelasticity is a crucial component of the observed mechanical response and hence has a significant effect on electromechanical actuation. This thesis reports on a constitutive theory and numerical modeling capability for dielectric viscoelastomers, able to describe electromechanical coupling, large- deformations, large-stretch chain-locking, and a time-dependent mechanical response. This approach is calibrated to the widely-used …

Modelling Of Oxygen Diffusion In Cork, Swapnil Shivputra Rane

Theses

The primary objective of this project is to better understand gas diffusion through natural cork structures by comparing simulations of gas diffusion through natural cork to experimental measurements of oxygen gas diffusion through the same structure. The cork's internal structure is measured using x-ray computed tomography (CT). From the measured internal structure, a simple mapping is assumed converting the measured x-ray computed tomography images into a 3D map of local diffusion coefficient. Specifically, it is assured that the x-ray CT pixel value is inversely proportional to the diffusion coefficient of oxygen through the cork. A diffusion model for the cork …

Numerical Assessment Of The Convective Heat Transfer In Rotating Detonation Combustors Using A Reduced-Order Model, James Braun, Jorge Sousa, Guillermo Paniagua

School of Aeronautics and Astronautics Faculty Publications

The pressure gain across a rotating detonation combustor offers an efficiency rise and potential architecture simplification of compact gas turbine engines. However, the combustor walls of the rotating detonation combustor are periodically swept by both detonation and oblique shock waves at several kilohertz, disrupting the boundary layer, resulting in a rather complex convective heat transfer between the fluid and the solid walls. A computationally fast procedure is presented to calculate this extraordinary convective heat flux along the detonation combustor. First, a numerical model combining a two-dimensional method of characteristics approach with a monodimensional reaction model is used to compute the …

Investigation Of Thermal History In Large Area Projection Sintering, An Additive Manufacturing Technology, Justin Nussbaum

USF Tampa Graduate Theses and Dissertations

The goal of this work is to explore the benefits of using long exposure times with polymer powder bed fusion additive manufacturing processes and examine the feasibly of this new application as a manufacturing process. It is well known that the sintering which occurs in these systems are a time and temperature dependent process. However, the most common powder bed fusion systems use a laser which scans and heats the powdered feedstock for microseconds at a time, leaving insufficient time for the polymer to fully melt and/or fuse, leading to reduced mechanical properties. Little has been published on the effects …

Fracture Initiation In A Transversely Isotropic Solid: Transient Three Dimensional Analysis, Louis Milton Brock

Mechanical Engineering Faculty Publications

A transversely isotropic solid is at rest, and contains a semi-infinite, plane crack. The axis of rotational material symmetry lies in the crack plane. Application of normal point forces to each face of the crack causes transient 3D growth. The related problem of discontinuities in displacement and traction that exist on regions that exhibit dynamic similarity is first considered. Analytic results are obtained in integral transform space. These lead to equations of the Wiener–Hopf type for the fracture problem. Analytic solutions are again obtained and, upon inversion, subjected to a dynamic energy release rate criterion that includes kinetic energy. A …

Perovskite Solar Cells Fabricated Via Scalable Dip Coating Methods, Joseph F. Iannello

Theses and Dissertations

Perovskite solar cells present the possibility for less expensive electricity generation, through the use of low cost materials and fabrication methods relative to current silicon-based technology. Many current methods of fabricating thin film perovskite solar cells focus on spin-coating, which inherently lacks scalability due to particle conglomeration, poor uniformity over a larger area, and safety concerns. Dip-coating, an alternative to spin-coating, which is explored here addresses these issues which limit scalability. Each individual layer can be separately synthesized, deposited, and characterized, which leads towards scalability. Choosing only the best results from each independent layer allowed progress to the creation of …

Two-Phase Flow Regime Map For Large Diameter Pipes And High-Velocity Flows, Matheus Sigaki Capovilla

LSU Master's Theses

Worst-case-discharge (WCD) calculations are a pre-requisite for any new well to be drilled in the Gulf of Mexico (GoM). Models that were mostly developed for production rates prediction are currently used to calculate the WCD rate. These models were mostly developed for pipe diameters and flow velocities much smaller than those expected during WCD events. Therefore, these models may be miscalculating WCD rates.

This study aims at analyzing one of possible sources of errors in these models: the flow regime maps. The influence of diameter change on flow regimes is discussed. A thorough literature review is carried out for different …

Residential Air Leakage Testing And Mechanical Ventilation Verification, Florida Solar Energy Center, Jeffrey Sonne

FSEC Energy Research Center®

This project is intended to answer the following four questions regarding residential building air leakage testing and whole-house mechanical ventilation requirements as stated in the 2016 Supplement 1 changes to the 5th Edition (2014) Florida Energy Conservation Code, and now continued in the 6th Edition (2017) Code: - Is the new requirement to test residential air leakage being followed? - Who is providing the air leakage testing? - Are accurate air leakage rate test values being reported? - Is whole-house mechanical ventilation being installed in applicable cases?

Three Speed 3d Printed Magnetic Gear, Robert J. Rutherford

Maseeh Summer Undergraduate Research Experience

Power transmission is traditionally achieved with a mechanical gear. Mechanical gears require maintenance, cause vibration, and have no overload protection. Magnetic gears offer an innovative solution to these drawbacks as they do not require regular maintenance, have no need for lubrication, create very little acoustic noise, have built in overload protection and as a result of these advantages, have a longer lifetime of operation. This research focused upon the design, assembly and demonstration of the magnetic gear concept. The research used a solid works design, 3D printed ABS plastic housing, and use of neodymium magnets and ferromagnetic iron segments.

This …

Designing Model Experiments Around Harriet Tubman Middle School, Ryan Crist, Sarah Smith, Greg Sakradse, Ryan Scott

Maseeh Summer Undergraduate Research Experience

Air quality is of concern in densely populated areas and especially near sources of inefficiently exhausted fossil fuel such as near the highway. Harriet Tubman middle school in North Portland, Oregon is situated alongside highway 5. Here, model experiments are designed and proposed to observe the instantaneous flow fields reflect modifications. LIDAR data was used to model the school and surrounding topography three-dimensionally in order to construct a model school and surrounding area from laser cut cardboard with a surface smoothed with paper mache. This model will be placed in the Portland State University wind tunnel; transport of mean and …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering: News & Publications (2013-2023)

• Recent Graduate at NASA’s Neutral Buoyancy Lab

Kinematic Analysis Of Spinal Cord Injury Animals Treated With A Neurotrophin-Infused Scaffold And Body Weight Supported Treadmill Training, Alexander Herman

Theses and Dissertations

Spinal Cord Injury (SCI) is a condition that affects around 250,000 Americans with no cure. Existing treatments rely on physical therapies such as body weight support treadmill training (BWSTT). Treatments currently being researched include the use of implantable cells and biomaterials. Our study investigated the changes in locomotive gait and range of motion via a combinational treatment using a bioengineered scaffold [poly (N-isopropyl acrylamide) polyethylene glycol (PNIPAAm-g-PEG) with BDNF and NT-3] and rehabilitation training using BWSTT in a clinically relevant contusion SCI animal model. Five different groups of animals (Sham, Injury, BWSTT, Implant, and Combinational) were tested on a treadmill …

System And Method For Controlling Operations Of Air - Conditioning System, Mouhacine Benosman, Petros Boufounos, Boris Kramer, Piyush Grover

Department of Mechanical and Materials Engineering: Faculty Publications

A method controls an operation of an air - conditioning system generating airflow in a conditioned environment . The method updates a model of airflow dynamics connecting values of flow and temperature of air conditioned during the operation of the air - conditioning system . The model is updated interactively iteratively to reduce an error between values of the airflow determined according to the model and values of the airflow measured during the operation . Next , the method models the airflow using the updated model and controls the operation of the air - conditioning system using the model .

Tutorial: Determination Of Thermal Boundary Resistance By Molecular Dynamics Simulations, Zhi Liang, Ming Hu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Due to the High Surface-To-Volume Ratio of Nanostructured Components in Microelectronics and Other Advanced Devices, the Thermal Resistance at Material Interfaces Can Strongly Affect the overall Thermal Behavior in These Devices. Therefore, the Thermal Boundary Resistance, R, Must Be Taken into Account in the Thermal Analysis of Nanoscale Structures and Devices. This Article is a Tutorial on the Determination of R and the Analysis of Interfacial Thermal Transport Via Molecular Dynamics (MD) Simulations. in Addition to Reviewing the Commonly Used Equilibrium and Non-Equilibrium MD Models for the Determination of R, We Also Discuss Several MD Simulation Methods Which Can Be …

Soft-Microrobotics: The Manipulation Of Alginate Artificial Cells, Samuel Sheckman

Mechanical Engineering Research Theses and Dissertations

In this work, the approach to the manipulation of alginate artificial cell soft-microrobots, both individually and in swarms is shown. Fabrication of these artificial cells were completed through centrifugation, producing large volumes of artificial cells, encapsulated with superparamagnetic iron oxide nanoparticles; these artificial cells can be then externally stimulated by an applied magnetic field. The construction of a Permeant Magnet Stage (PMS) was produced to manipulate the artificial cells individually and in swarms. The stage functionalizes the permanent magnet in the 2D xy-plane. Once the PMS was completed, Parallel self-assembly (Object Particle Computation) using swarms of artificial cells in complex …

A Microresonator-Based Laser Doppler Velocity Sensor For Interplanetary Atmospheric Re-Entry, Benjamin Wise

Mechanical Engineering Research Theses and Dissertations

In this thesis, a laser velocity sensor concept based on optical microresonators is presented and the application to spacecraft atmospheric entry is explored. The concept is based on the measurement of Doppler shift of back-scattered laser light. Specifically, the Doppler shift is detected by observing the whispering gallery optical modes (WGM) of a dielectric microresonator excited by the back scattered light from particulates and gas molecules. The microresonator replaces the typical Fabry-Perot interferometer and CCD camera system, thereby significantly reducing the size and weight of the overall detection system. This thesis presents proof-of-concept results for this measurement approach. The Doppler …