Mechanical Engineering Commons^™

Variable Fluid Flow Regimes Alter Endothelial Adherens Junctions And Tight Junctions, Dilshan Ranadewa

Electronic Theses and Dissertations

Variable blood flow regimes influence a range of cellular properties ranging from cell orientation, shape, and permeability: all of which are dependent on endothelial cell-cell junctions. In fact, cell-cell junctions have shown to be an integral part of vascular homeostasis through the endothelium by allowing intercellular signaling and passage control through tight junctions (TJs), adherens junctions (AJs), and gap junctions (GJs). It was our objective to determine the structural response of both AJs and TJs under steady and oscillatory flow. Human brain microvascular endothelial cells (HBMECs) were cultured in a parallel plate flow chamber and exposed to separate trails of …

Dynamic Behavior And Performance Of Different Types Of Multi-Effect Desalination Plants, Mohamed Abdelkareem

Electronic Theses and Dissertations

Water and energy are two of the most vital resources for the socio-economic development and sustenance of humanity on earth. Desalination of seawater has been practiced for some decades and is a well-established means of water supply. However, this process consumes large amounts of energy and the global energy supply is also faced with some challenges. In this research, multi-effect desalination (MED) has been selected due to lower cost, lower operating temperature and efficient in terms of primary energy and electricity consumption compared to other thermal desalination systems. The motivation for this research is to address thermo-economics and dynamic behavior …

Fatigue Characteristics Of New Eco Series Aluminum 7175 Alloy, Chinh Q.L. Vu

Dissertations and Theses

In this dissertation, the fatigue characteristics of three newly developed experimental compositions for aluminum 7175, with improved mechanical strength, that uses magnesium-calcium alloy instead of pure magnesium are studied.

Specimens of each variant were fabricated and subjected to fatigue life testing, fatigue life data analysis, and observation of their fracture characteristics through optical microscopy and scanning electron microscopy (SEM), and metallography to study their grains and surface characteristics.

Fatigue life testing shows all three variants have a fatigue strength that is approaching approximately 200 MPa. ECO7175v3 is shown to have the highest fatigue strength of approximately 220 MPa at 5x10 …

The Effects Of Bone Morphogenic Protein 2 On The Viability And Proliferation Of Dental Pulp Stem Cell Isolates, Joseph Cinelli

UNLV Theses, Dissertations, Professional Papers, and Capstones

Growth factor is an umbrella term used to describe a signaling molecule present in organisms that serves the purpose of influencing a stimulatory or inhibitory response from the target cell it acts on. Growth factors are categorized and classified by the types of tissues they act on and the cellular responses they illicit. For example, there are growth factors that act primarily in connective tissue on fibroblasts and they are aptly classified as the fibroblast growth factor family. Similarly, there is another family of growth factors that act on bone forming cells, among others, and they are known as bone …

The Development Of A Viscoelastic Ellipsoidal Model For Use In Measuring Plantar Tissue Material Properties During Walking, Jessica Lee Deberardinis

UNLV Theses, Dissertations, Professional Papers, and Capstones

Introduction: The mechanical characteristics of the plantar tissues during walking is not well understood as most of the current research focuses on testing specific plantar regions in cadavers or while the feet of the participants are raised. In this work, it is hypothesized that a viscoelastic geometric ellipsoid model used to assess multiple structures of the foot would be accurate and robust. This model would be participant-specific and applicable to the entire stance phase of gait.

Methods: The proposed viscoelastic ellipsoid model would represent several key anatomical areas: Heel, Posterior Midfoot, Anterior Midfoot, Metatarsals 1-2, Metatarsals 3-5, Toe 1, Toe …

A Monolithic Arbitrary Lagrangian-Eulerian Finite Element Method For An Unsteady Stokes/Parabolic Interface Problem, Ian Kesler

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this thesis, a non-conservative arbitrary Lagrangian-Eulerian (ALE) method is developed

and analyzed for a type of linearized Fluid-Structure Interaction (FSI) problem in a

time dependent domain with a moving interface - an unsteady Stokes/parabolic interface

problem with jump coefficients. The corresponding mixed finite element approximation is

analyzed for both semi- and full discretization based upon the so-called non-conservative

ALE scheme. The stability and optimal convergence properties in the energy norm are

obtained for both schemes.

The Affective Perceptual Model: Enhancing Communication Quality For Persons With Pimd, Jadin Tredup

UNLV Theses, Dissertations, Professional Papers, and Capstones

Methods for prolonged compassionate care for persons with Profound Intellectual and Multiple Disabilities (PIMD) require a rotating cast of import people in the subjects life in order to facilitate interaction with the external environment. As subjects continue to age, dependency on these people increases with complexity of communications while the quality of communication decreases. It is theorized that a machine learning (ML) system could replicate the attuning process and replace these people to promote independence. This thesis extends this idea to develop a conceptual and formal model and system prototype.

The main contributions of this thesis are: (1) proposal of …

Autonomous Vehicles Operating Collaboratively To Avoid Debris And Obstructions, Toan T. Le, Cole W. Oppenheim, James H. Gildart, Kyle M. Bybee

Mechanical Engineering

The purpose of this project is to demonstrate the safety and increased fuel efficiency of an automated collision avoidance system in collaborative vehicle platooning. This project was cosponsored by Daimler Trucks North America headquartered in Portland, Oregon, as well as Dr. Birdsong, and Dr. DeBruhl of Cal Poly. The mechanical engineering team consists of Cole Oppenheim, James Gildart, Toan Le, and Kyle Bybee who worked in coordination with a team of computer engineers. Vehicle platooning is a driving technique to increase the fuel efficiency of a group of vehicles by following a lead vehicle closely to reduce the drag experienced …

Adjustable Seating Systems, Grace Timken, Zachary Dworaczyk, Jasper Lewin, Eric Voss

Mechanical Engineering

The Adjustable Seating Systems team designed and prototyped a collapsible and nestable seat for use in transit vehicles to create more free space for more passengers and cargo. Our team is the second senior project group to have worked at solving this problem. The previous team established a unique seat folding method that is currently pending patent approval. Our team’s responsibility was to improve the ease of use and overall hardware design of the entire seating system. This document captures the efforts that our team has performed to organize an approach to completing a full design and working prototype this …

Danny’S Recumbent Bike Accessibility Device Final Design Report, Joseph J. Lee, Huy Nguyen, Jack Mcatee, John Kulick

Mechanical Engineering

The purpose of this document is to fully define our design solution and explain our manufacturing and testing results. Our project’s goal is to find a way to allow Danny Knutson, a retired Navy pilot and incomplete quadriplegic with limited use of his arms and an impaired sense of balance, to enter and exit his recumbent tricycle without any discomfort for him or his aide. We completed multiple interviews with Danny, patent research, existing product research, and other technical literature research in order to fully understand the problem. We synthesized this information to create a concrete list of customer wants …

High Strollers, Braeden Hammond, Morley Perrin, Reid Bartels, Juan Rodriguez

Mechanical Engineering

This report documents the final product of Jonathon’s new lightweight stroller. The Mechanical Engineering team from Cal Poly, High Strollers, began the project to create a lightweight stroller for the project sponsor, Nina Aguayo, and her son, Jonathon Aguayo, in Fall of 2018. Jonathon is diagnosed with Delayed Brain Development and Hypotonia with some characteristics of Cerebral Palsy. He has a 50lb high intensity stroller to go to and from school. Mrs. Aguayo needed a stroller that is easier to transport while still meeting all of Jonathon’s needs. The re-designed stroller will make leisurely outings for Mrs. Aguayo and Jonathon …

Go With The Flow, Scott Weinhardt, Priscilla Ng, Ben Rydberg, Ritika Makhijani

Mechanical Engineering

This Final Design Review (FDR) report outlines the Fuel System Flow Analysis senior project completed by the presenters listed. Included is research about Solar Turbines’ needs, and objectives for our project, our design decision process and final design, manufacturing, design verification report, final results, and suggestions moving forward with this experiment. The goal of the project is to identify stable pressure fields throughout the Solar Turbines fuel delivery system. Specifically, the optimal placement for taking measurements downstream of the main and pilot fuel control valves. The data is used to validate the accuracy of computational fluid dynamic (CFD) models that …

Bgaas Alloy Semiconductors For Lasers On Silicon, Joshua Mcarthur

Mechanical Engineering Undergraduate Honors Theses

In the world of semiconductors today, there is a large dissonance between optical devices and electrical application. Due to the limitations of electron transport, photonic integrated circuits are soon-to-be vital in fields like telecommunications and sensing. Right now, these PIC’s are mostly made from indium phosphide. Due to its ubiquitous nature, however, there is a huge push to integrate efficient optics with silicon. It’s cheap, abundant, dope-able, and our electronic infrastructure is based on it. The reason why silicon photonics aren’t already commercialized is because of silicon’s indirect bandgap—it is inefficient with optical applications. The problem with combining direct gap …

The Analysis Of Erlanger Hospital’S Suture Inventory Management Operations, Amanda George

Honors Theses

This paper evaluates the impact of using mechanical engineering and operations management principles to an inventory management system in Erlanger Hospital. Erlanger Hospital is a local, nonprofit hospital system in Chattanooga. Erlanger serves as a tertiary referral hospital and a Level I Trauma Center in the region. Therefore, they are heavily depended on during times of crisis or emergency [2]. This study focuses specifically on reducing the loss and ultimate waste of sutures across Erlanger’s surgery wing. A criteria for the appraisal of using mechanical and manufacturing engineering to improve the current system is established based on existing data regarding …

Computational Simulation Of The Paw-04 Nozzle Configuration, Juan Hernandez

Honors Theses

The research was based on the 4th Propulsion Aerodynamics Workshop which was organized by the American Institute of Aeronautics and Astronautics (AIAA) Air Breathing Propulsion System Integration Technical Committee and its objective was to assess the accuracy and numerical prediction capabilities of Computational Fluid Dynamics (CFD). It focused on the work of Behrouzi and McGuirk where they tested two different nozzle configurations under set boundary conditions. The nozzle configurations included a high aspect ratio rectangular nozzle with a clean exit and the same nozzle with an aft-deck attached to the exit. Three different unstructured grids were generated for the clean …

The Effect Of Soil Saturation On The Heat Transfer Rate In A Controlled Environment For Application To Ground Source Heat Pumps, William Barnard

Honors Theses

With the worldwide push for environmentally friendly technology, the topic of geothermal systems has only become more important. Ground Source Heat Pumps (GSHPs) are heat pumps that take advantage of the natural temperature difference between the soil and the air to decrease the amount of power necessary to heat an area. A GSHP has been shown to be capable of increasing efficiency by 3 or 4 times the amount of a conventional heating and cooling system [4]. To take advantage of the full capabilities of a GSHP, one needs to understand what factors can increase or decrease efficiency. While research …

Universal Bike Suspension Design, Ernesto Huerta, Gregory Ryan Ritter, Chris Michael Fedor, Michael Wu

Mechanical Engineering

Cal Poly Bike Builders (CPBB) is a student club at Cal Poly helping students design and fabricate their own bicycles. Currently, club members build rigid frames and mountain bikes with only front-suspension–commonly referred to as a “hardtail”. As more students join the club, interest grows in building full-suspension mountain bikes (FSMTB). Designing and manufacturing a mountain bike rear-suspension system requires a diverse skillset and a substantial time commitment. As a result, individual efforts building FSMTB have proven unsuccessful. The scope of this project is to develop a defined method and necessary tools such that all CPBB members can efficiently build …

A Study On Ultrasonic Energy Assisted Metal Processing : Its Correeltion With Microstructure And Properties, And Its Application To Additive Manufacturing., Anagh Deshpande

Electronic Theses and Dissertations

Additive manufacturing or 3d printing is the process of constructing a 3-dimensional object layer-by-layer. This additive approach to manufacturing has enabled fabrication of complex components directly from a computer model (or a CAD model). The process has now matured from its earlier version of being a rapid prototyping tool to a technology that can fabricate service-ready components. Development of low-cost polymer additive manufacturing printers enabled by open source Fused Deposition Modeling (FDM) printers and printers of other technologies like SLA and binder jetting has made polymer additive manufacturing accessible and affordable. But the metal additive manufacturing technologies are still expensive …

Secondary Resonances Of Electrostatically Actuated Mems Cantilevers, Christopher I. Reyes

Theses and Dissertations

In this work the behavior of micro-electromechanical (MEMS) cantilever resonators is investigated. The cantilever resonators are electrostatically actuated with hard AC voltage resulting in nine distinct resonances cases including super and subharmonic resonances. The amplitude frequency and amplitude voltage bifurcation diagrams are obtained for each of the nine resonance cases. Reduced order models (ROMs) are developed to include one and two modes of vibration. Three different methods are used to solve the ROMs namely 1) the method of multiple scales (MMS), which is a perturbation method used for one mode of vibration, 2) the homotopy analysis method (HAM), which is …

Methods To Remotely Eliminate Biofilm From Medical Implants Using 2.4 Ghz Microwaves, Brett Glenn

Mechanical Engineering Undergraduate Honors Theses

Infections associated with biofilm growth are usually challenging to eradicate due to their high tolerance toward antibiotics [11, 12]. Biofilms often form on the inert surfaces of medically implanted devices [13]. No matter the sophistication, microbial infections can develop on all medical devices and tissue engineering constructs [12]. Related infections lead to 2 million cases annually in the U.S., costing the healthcare system over $5 billion in additional healthcare expenses [12].

Novel solutions to biofilm’s microbial colonization span the spectrum of engineering and science disciplines. Yet a practical solution still does not exist. The research presented here will explore a …

Challenges And Opportunities Of Layered Cathodes Of Linixmnyco(1-X-Y)O2 For High-Performance Lithium-Ion Batteries, Jason Frank

Mechanical Engineering Undergraduate Honors Theses

High energy density lithium-ion batteries (LIBs) are widely demanded for portable electronic devices and electrical vehicles. Layered-structure LiCoO₂ oxide (LCO) has been the most commonly used cathode material in commercial LIBs. Compared to LCO, LiNi_1-x-yMn_xCo_yO₂ (NMC) cathodes are particularly attractive due to their reduced cost and higher capacity. Among the NMC cathodes, nickel-containing LiNi_0.5Co_0.3Mn_0.2O₂ (NMC532) is one of the most promising cathode materials undergoing intensive investigation, but suffers from a series of technical issues, such as structural instability, performance fading, and safety issues. In this …

Development Of Small-Scale And Low-Power Attitude Determination System For Nanoscale Satellites By Infrared Earth-Imaging Sensors, Zachary Tolar

Mechanical Engineering Undergraduate Honors Theses

Many space missions require that the spacecraft be oriented in a specific direction to operate correctly. ARKSAT 1, the University of Arkansas’s first satellite, is a 1U CubeSat designed to perform atmospheric spectroscopy from Low-Earth Orbit and as such requires precise attitude determination and control. Currently, attitude determination systems for 1U CubeSats with small space, low power, and low cost restrictions do not exist. This paper discusses the development of an earth-imaging infrared camera system for attitude determination on CubeSats and SmallSats that meets these requirements. Melexis MLX 90640 IR arrays and Microchip 8-bit microcontrollers are used to create infrared …

Modelling Palladium Decorated Graphene Using Density Functional Theory To Analyze Hydrogen Sensing Application, Sameer Kulkarni

Mechanical Engineering Undergraduate Honors Theses

Graphene is an exciting new material with many promising applications. One such application of graphene is gas sensing, when adsorbed with transition metals, notably Palladium. Therefore, it is of paramount importance to have appropriate ab initio calculations to calculate the various properties of graphene under different adsorbates and gasses. The first step in these calculations is to have a functioning base Density Functional Theory (DFT) model of pristine graphene decorated with Palladium. The computational methods described in this paper has yielded results for pristine graphene that have been confirmed many times in previous experimental and theoretical studies. Future work needs …

Design Of A Bedside Walker-Cane Hybrid To Aid Senior Adults Avoid Falls During Night Walks, Jorge L. Gutierrez

Theses and Dissertations

The objective of this research and development work is to design a device to help senior adults prevent fall during night walks indoors. The problem of elders falling at a night setting was found to be caused by the multiple environmental and medical conditions. The target demographic was found to be seniors from age 65 and older. Several occupational therapists and two physical therapists were consulted to gain knowledge on elders' behavior, possible improvements on current existing devices, and feedback regarding the early prototype built. Several products and patents were researched with a lack of findings on similar products that …

Biomechanics Of Lower Limb During The Golf Swing Using Opensim Modeling, Andrew B. Butler

Theses and Dissertations

The purpose of this research is to investigate the biomechanics of the lower-limb using an inverse dynamics model. Experimental data, recorded by an integrated Motion Analysis – Force Plate System in the UTRGV Biomechanics Laboratory, is used to determine ground reaction forces and marker trajectories. OpenSim, a graphical musculoskeletal and computational platform, is used to model the body in three dimensions. The human body is modeled as a 12-segment linkage, consisting of 23 degrees-of-freedom and 92 muscles. The experimental data for the Biomechanics Laboratory is imported in OpenSim. Then, joint angles, generalized coordinates & accelerations of lower-limb segments, muscle forces, …

Experimental Study Of Condensation In Different 3d Printed Regenerators In A Thermoacoustic Cooler, Aibek Bekkulov

Theses and Dissertations

Thermoacoustics (TA) deals with the conversion of heat into sound and vice versa. Device that converts heat into acoustic work is called TA heat engine, while the device that transfers energy from a low temperature reservoir to a high temperature one by utilizing acoustic work is called TA cooler. A simple construction of TA cooler includes an acoustic speaker, a resonator tube and a regenerator stack in which the temperature gradient is being imposed. Such a TA cooler has several advantages over traditional compression/expansion cooling machine such as its simplicity of the construction, high reliability and lack of toxic refrigerants. …

Development Of Flexible Photo-Mechanoluminescent Polymeric Based Systems, Carlos Hernandez

Theses and Dissertations

The project focuses on the creation of nanofiber systems with enhanced photo-mechanoluminescent response and high mechanical flexibility to further enhance promising optical applications. Lanthanide-Polyvinyl Di-Fluoride fiber systems were created using centrifugal spinning and characterized using SEM, FTIR, XPS, DSC, XRD, and PL. Fibers luminescence response was gotten when induced by ultraviolet light and the application of an impact force.

Polymeric Pvdf Fibers For Piezoelectric Applications In Energy Harvesting, Misael E. Martinez

Theses and Dissertations

This work focuses on developing and characterizing the piezoelectric response of Cerium doped Polyvinylidene Fluoride (PVDF) fine fibers and the effects of dopants and alignment on the formation of the β-phase and consequently on the piezoelectric performance. Six sets of fiber mats were prepared varying the concentration (2.5–7.5wt%) of Cerium (III) Nitrate-Hexahydrate and Ammonium-Cerium (IV) Sulfate-Dihydrate. Fiber mats were developed using the Forcespinning® technique and the angular velocity and dopant concentration were adjusted to obtain a synergy between fiber yield and fiber diameter. Fourier Transform Infrared Spectroscopy showed a significant enhancement in the PVDF β-phase and inhibition of the non-polar …

Blockchain Technology Based Supply Chain Systems And Supply Chain Performance: A Resource-Based View, Madhavi Latha Nandi

Theses and Dissertations

Blockchain technology (BCT) is set to transform firms’ present ways of managing supply chains. This thesis explores how the efforts by firms to integrate BCT into their supply chain systems and activities, can enable certain supply chain capabilities and subsequently, improve supply chain performance. Using an abductive research approach, qualitative content analyses of 126 cases of firms’ efforts in BCT-based supply chain systems (BCT-SCS) across multiple industries are conducted to identify the BCT-enabled supply chain capabilities and their performance outcomes. Findings reveal that the present BCT-SCS efforts are mainly oriented towards improving the operational-level capabilities namely, information sharing and coordination …

Mechanical Characterization And Fracture Behavior Of Magnesium Zk60a Alloy (Uns M16600), Mohamed Kamal I. H. Temraz

Theses

This research work focuses on studying the mechanical and fracture behavior of one of magnesium ZK60A (UNS M16600) extrusion. The material has many industrial applications and its characteristic should be measured for proper component or system design. Several tests were conducted following the standard procedures to determine the mechanical characteristics of the material. In addition, the fracture toughness of the material has been measured using the fracture toughness-thickness curve. A stress intensity factor K was used as a fracture parameter to determine the plane strain fracture toughness KIC of ZK60A magnesium alloy using a single edge notch bend (SENB) specimen …