Mechanical Engineering Commons^™

Epitaxial Growth Of Iii-Nitride Nanostructures And Their Optoelectronic Applications, Moab Rajan Philip

Dissertations

Light-emitting diodes (LEDs) using III-nitride nanowire heterostructures have been intensively studied as promising candidates for future phosphor-free solid-state lighting and full-color displays. Compared to conventional GaN-based planar LEDs, III-nitride nanowire LEDs exhibit numerous advantages including greatly reduced dislocation densities, polarization fields, and quantum-confined Stark effect due to the effective lateral stress relaxation, promising high efficiency full-color LEDs. Beside these advantages, however, several factors have been identified as the limiting factors for further enhancing the nanowire LED quantum efficiency and light output power. Some of the most probable causes have been identified as due to the lack of carrier confinement in …

Tomato Puree Convective Heat Transfer Simulation Using Boussinesq Approximation, Matteo Fabbri

Theses

With the advance of new technologies, the food industries are requiring systems that allow to produce the desired products with faster rates at cheaper costs. In this case, the study was initiated with the purpose to better understand what happens inside a package containing tomato puree when this is heated above 343 K in a tunnel pasteurizer. If the fluid must reach the thermal and microbiological condition of “pasteurization”, the system must guarantee that the temperature (around 343° Kelvin) is kept for a certain time allowing to pasteurize even the cooler package’s fluid-particle. The faster the system can heat the …

Mechanics Of Binder-Particle Interactions In Composite Battery Electrodes, Richard Johnson

Theses

A study into the particle level mechanics of polymer binder and active material used in composite lithium-ion batteries (LIB) has been conducted. Silicon is highly sought after material that can be used as an active material in a composite anode. Its high theoretical capacity can result in batteries that can store more energy than current LIBs, but high volume expansion of Si during charge/discharge cycles leads to rapid capacity fade and poor cyclic life. Understanding the stress that is generated in the binder and the active material due to the volume expansion has not been fully understood. In this study …

Swarm-Based Techniques For Adaptive Navigation Primitives, Nathan Metzger

Mechanical Engineering Master's Theses

Adaptive Navigation (AN) has, in the past, been successfully accomplished by using mobile multi-robot systems (MMS) in highly structured formations known as clusters. Such multi-robot adaptive navigation (MAN) allows for real-time reaction to sensor readings and navigation to a goal location not known a priori. This thesis successfully reproduces MAN cluster techniques via swarm control techniques, a less computationally expensive but less formalized control technique for MMS, which achieves robot control through a combination of primitive robot behaviors. While powerful for large numbers of robots, swarm robotics often relies on “emergent” swarm behaviors resulting from robot-level behaviors, rather than top-down …

Surface Engineering Solutions For Immersion Phase Change Cooling Of Electronics, Brendon M. Doran

Master's Theses

Micro- and nano-scale surface modifications have been a subject of great interest for enhancing the pool boiling heat transfer performance of immersion cooling systems due to their ability to augment surface area, improve wickability, and increase nucleation site density. However, many of the surface modification technologies that have been previously demonstrated show a lack of evidence concerning scalability for use at an industrial level. In this work, the pool boiling heat transfer performance of nanoporous anodic aluminum oxide (AAO) films, copper oxide (CuO) nanostructure coatings, and 1D roll-molded microfin arrays has been studied. Each of these technologies possess scalability in …

Reversal Of Transmission And Reflection Based On Acoustic Metagratings With Integer Parity Design., Yangyang Fu, Chen Shen, Yanyan Cao, Lei Gao, Huanyang Chen, C T Chan, Steven A Cummer, Yadong Xu

Henry M. Rowan College of Engineering Departmental Research

Phase gradient metagratings (PGMs) have provided unprecedented opportunities for wavefront manipulation. However, this approach suffers from fundamental limits on conversion efficiency; in some cases, higher order diffraction caused by the periodicity can be observed distinctly, while the working mechanism still is not fully understood, especially in refractive-type metagratings. Here we show, analytically and experimentally, a refractive-type metagrating which can enable anomalous reflection and refraction with almost unity efficiency over a wide incident range. A simple physical picture is presented to reveal the underlying diffraction mechanism. Interestingly, it is found that the anomalous transmission and reflection through higher order diffraction can …

Effects On Strength And Corrosive Characteristics Of Hardened Cement Paste Using Rice Husk And Sugarcane Bagasse, Travis D. Garrett

Master's Theses

Cement is one of the most used building materials in the world. The production of ordinary Portland cement contributes to the release of harmful greenhouse gasses. In an effort to reduce these emissions, different materials are being evaluated for their use as partial replacements for ordinary Portland cement. Rice husk and sugarcane bagasse are agricultural waste products and large amounts of these are currently landfilled, making them inexpensive and available. When combusted at high temperatures they form rice husk ash and sugarcane bagasse ash that have pozzolanic characteristics. The high silicon dioxide in these products makes them good options to …

Modeling The Effect Of A Compartment Fire On Spaces Adjacent To A Bulkhead With And Without Attachments, Carl E. Hendrickson Ii

LSU New Orleans Theses and Dissertations

Structural fire protection is an integral component of shipboard fire safety. There are national and international regulations that delineate requirements for the insulation placed throughout ships. The attachments that penetrate the insulation for hanging wires and pipes can disrupt the integrity of the division, and cause a failure to adhere to the regulations. This problem will be analyzed by using a simplified lumped capacitance model and ANSYS FLUENT CFD. A standard time-temperature fire curve is applied to the fire side of the enclosure. The thermal conductivity of the insulation and steel are made to be temperature dependent. The density of …

Using Thermal Gradient Measurements To Compare Bath Temperature And Agitation Effects On The Quenching Performance Of Palm Oil, Canola Oil And A Conventional Petroleum Oil, Bozidar Matijevic, Bruno F. Canale, Božidar Lišcic, George Totten

Mechanical and Materials Engineering Faculty Publications and Presentations

A proprietary Liscic/Petrofer cylindrical Inconel 600 probe of 50-mm diameter and 200-mm length which was instrumented with three thermocouples on the same radius of the crosssection at the middle of the length was used to determine the differences in quenching performance of two vegetable oils, palm oil and canola oil, and they were compared to a locally produced conventional petroleum oil quenchant. The cooling curves and heat transfer performance of these oils were determined at different bath temperatures and agitation rates. The work was performed at the Quenching Research Centre located at the Faculty for Mechanical Engineering, University of Zagreb, …

Mechanical Properties And Applications Of Recycled Polycarbonate Particle Material Extrusion-Based Additive Manufacturing, Matthew J. Reich, Aubrey Woern, Nagendra Gautam Tanikella, Joshua M. Pearce

Michigan Tech Publications, Part 1

Past work has shown that particle material extrusion (fused particle fabrication (FPF)/fused granular fabrication (FGF)) has the potential for increasing the use of recycled polymers in 3D printing. This study extends this potential to high-performance (high-mechanical-strength and heat-resistant) polymers using polycarbonate (PC). Recycled PC regrind of approximately 25 mm² was 3D printed with an open-source Gigabot X and analyzed. A temperature and nozzle velocity matrix was used to find useful printing parameters, and a print test was used to maximize the output for a two-temperature stage extruder for PC. ASTM type 4 tensile test geometries as well as ASTM-approved …

Design And Control Of Fiber Encapsulation Additive Manufacturing, Matt Saari

Mechanical Engineering Research Theses and Dissertations

This work presents the design, development, and analysis of the Fiber Encapsulation Additive Manufacturing (FEAM) system developed at the Laboratory for Additive Manufacturing Robotics \& Automation at the Lyle School of Engineering at Southern Methodist University. The innovation introduced by FEAM is the ability to insert a continuous fiber of different material into the flowing extrudate. Correctly positioning the fiber feed inside the extrudate while turning the fiber in arbitrary directions is a critical aspect of the technology. This will allow for the full exploitation of the capabilities of the FEAM technology to produce robotic components that actuate and sense. …

Breakage Modeling Of Needle-Shaped Particles Using The Discrete Element Method, Rohit Kumar, William Ketterhagen, Avik Sarkar, Jennifer S. Curtis, Carl Wassgren

School of Mechanical Engineering Faculty Publications

This paper models the breakage of large aspect ratio particles in an attrition cell using discrete element method (DEM) and population balance (PB) models. The particles are modeled in DEM as sphero-cylinders. The stresses within each particle are calculated along the particle length using beam theory and the particle breaks into two parts if the stress exceeds a critical value. Thus, the size distribution changes with time within the DEM model. The DEM model is validated against previously published experimental data.

The simulations demonstrate that particle breakage occurs primarily in front of the attrition cell blades, with the breakage rate …

Computation Of Flow Fields Due To Single- And Twin-Jet Impingement, Xiang Zhang

McKelvey School of Engineering Graduate Student Theses & Dissertations

The thesis consists of two parts. The first part focuses on numerical simulations and their comparison with experimental data for single-jet impingement on ground. Angles between the axisymmetric jet and impingement surface considered are 15, 30 and 90 degree. It is shown that both the k-epsilon and Wray-Agarwal (WA) model can predict the flow fields in good agreement with the experimental results. The second part extends the first part to twin-jet normal impingement on the ground. It focuses on numerical simulation of fountains formed by the twin-jet impingement. The fountains can be normal straight upward when the two jets are …

Using Numerical Models Of Dewatering At Coal Ash Impoundments To Understand Cost And Schedule, Peter Bell, Joel Thompson, Don Fuller

World of Coal Ash Proceedings

No abstract provided.

Investigating Ccr Units And Evaluating The Physical Properties Of Ponded Ccr, David Skeggs, Zahra Aghazadeh, Rachel Combs

World of Coal Ash Proceedings

No abstract provided.

Demonstration Of “No Migration” Alternative Performance Standard For Ccr Facilities In Arid To Semi- Arid Regions Using Unsaturated Zone Modeling, James Aiken, Katy Lindstom

World of Coal Ash Proceedings

No abstract provided.

Coal Combustion Residuals Management Using Geotextile Containers- Considerations For Various Options, Randall Wilcox, Gregg Lebster, Bryan Hamilton, Thomas Stephens

World of Coal Ash Proceedings

No abstract provided.

State Vs Federal Ccr Rule Regulations: Comparisons And Impacts, Nicole Kron, Eric Nelson

World of Coal Ash Proceedings

No abstract provided.

Continuous, Real-Time Tss Monitoring Verifies Effluent Quality And Coal Ash Management Performance While Reducing Compliance Costs, Dave Fraley, Chris Bauman, Dave Donahue

World of Coal Ash Proceedings

No abstract provided.

Effect Of Coal Fly Ash On Agricultural Crops :Second Phase Showcase Project On Use Of Fly Ash In Agriculture In And Around Thermal Power Station Areas Of National Thermal Power Corporation Ltd., India., K. Arivazhagan, M. Ravichandran, S.K. Dube, V.K. Mathur

World of Coal Ash Proceedings

No abstract provided.

Advantages Of Single Source Contracting In-Plant Ccr Services, Kevin Foody, Marcella Funderburg, Blake Whittington

World of Coal Ash Proceedings

No abstract provided.

Design And Construction Of A Ccr Landfill Adjacent To The Missouri River, Thomas Gredell, Jeffrey Fouse, Jay Ellington

World of Coal Ash Proceedings

No abstract provided.

Geochemical Tools For Groundwater Monitoring At Coal Fired Utilities, Jeff Gillow, Bruce Sass, Hari Parthasarathy

World of Coal Ash Proceedings

No abstract provided.

Bottom Ash Handling Conversions – Lessons Learned, Dustin Doerr

World of Coal Ash Proceedings

No abstract provided.

Encapsulation Of Thermoevaporation Brines Using Coal Combustion Residuals, Dale Prentice, Kirk Ellison, Gaurav Sant

World of Coal Ash Proceedings

No abstract provided.

Recycling Of Coal Ash In Agriculture: Use Of Vermicomposting Biotechnology, G.N. Chattopadhyay, Gourab Roy, Wasim Iftikar

World of Coal Ash Proceedings

No abstract provided.

Surface Water And Groundwater Mixing In Alluvial Floodplains: A Significant Issue For Understanding Contaminant Transport At Coal Ash Facilities Adjacent To Rivers, Joel Thompson, Peter Bell, John Griggs

World of Coal Ash Proceedings

No abstract provided.

Alternate Source Demonstration Considerations Within The Appalachian Basin, Joseph Robb, Larry Mastera

World of Coal Ash Proceedings

No abstract provided.

Locating And Permitting A Ccr Landfill Adjacent To The Missouri River, Paul Reitz, Thomas Gredell, Jay Ellington

World of Coal Ash Proceedings

No abstract provided.

Is Zero Solid Waste Possible For Fly Ash Produced From Any Coal-Fired Power Plant?, Jinder Jow, Yang Dong, Shuqiang Ding, Li Qiao

World of Coal Ash Proceedings

No abstract provided.