Open Access. Powered by Scholars. Published by Universities.®

Power and Energy Commons™

Open Access. Powered by Scholars. Published by Universities.®

Discipline
Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 3811 - 3840 of 3927

Full-Text Articles in Power and Energy

The Impact Of Electronic Ballast Compact Fluorescent Lighting On Power Distribution Systems, Reid Iwao Sasaki Sep 1994

The Impact Of Electronic Ballast Compact Fluorescent Lighting On Power Distribution Systems, Reid Iwao Sasaki

Department of Electrical and Computer Engineering Technical Reports

Due to the high costs of expanding generation and transmission capacities, utilities have been initiating programs to reduce peak power demand by the customer. A number of these programs, which are commonly referred to as demand side management programs, have turned to the promotion of electronic ballast compact fluorescent lamps (CFLs) as an alternative to traditional incandescent lamps. These lamps provide a higher luminance and increased life as compared to their incandescent counterparts. Unfortunately, electronic ballast CFLs consume large amounts of harmonic current which may prove detrimental to the power distribution system. This thesis presents an introduction to the electronic …


An Appraisal Of Electricity Supply In Nigeria And The Privatisation Option, E. I. K. Sule, C. M. Anyanwu Aug 1994

An Appraisal Of Electricity Supply In Nigeria And The Privatisation Option, E. I. K. Sule, C. M. Anyanwu

CBN Occasional Papers

Incessant electric power cuts in most parts of the country has become a normal feature of electricity supply throughout Nigeria. The power outages cause much inconvenience and economic losses to all and sundry. This study has shown that the most critical factor behind the incessant power failure is the problem of inadequate funding of the industry at a time it was forced to accommodate rapid expansion. Other factors include lack of autonomy, inefficiency, poor organization as well as lack of skilled manpower. The paper has examined these problems on the basis of which suggestions are made on how the worrisome …


The Effects Of Channel Curvature And Protusion Height On Nucleate Boiling And The Critical Heat Flux Of A Simulated Electronic Chip, John E. Leland May 1994

The Effects Of Channel Curvature And Protusion Height On Nucleate Boiling And The Critical Heat Flux Of A Simulated Electronic Chip, John E. Leland

Office for Research Publications and Presentations

The quest for higher power yet smaller electronics has given rise to the need for very effective cooling of these electronics. Because one of the foremost problems in electronics cooling is achieving high heat flux cooling within small packages while expending minimal pumping power, one focus of this study was to investigate the effects of channel curvature on the CHF. Experimental data were obtained for flow rates of 1-7 m/s, subcoolings of 5-35"C, and radii of curvature of 25.4 and 50.8 mm. A correlation was obtained for these data which provided an excellent fit.

One condition that has been ignored …


Plains Electric Members Service Area_04-29-1994, University Of New Mexico Bureau Of Business And Economic Research Apr 1994

Plains Electric Members Service Area_04-29-1994, University Of New Mexico Bureau Of Business And Economic Research

BBER Publications

This report presents historical and projected socioeconomic data for 19 New Mexico and two Arizona counties which comprise the service areas of the distribution cooperatives in the Plains Electric Generation and Transmission Cooperative, Inc., system.


Basic Resonant Topologies For Switching Power Supplies, Zacharias K. Vachaparambil Apr 1994

Basic Resonant Topologies For Switching Power Supplies, Zacharias K. Vachaparambil

Department of Electrical and Computer Engineering Technical Reports

The objective of this thesis is to study the basic resonant converter topologies for switching power supplies and to compare their performance under different operating conditions. The series and parallel resonant converters are analyzed in detail. The analysis uses the state plane method, which gives a good insight of the operation of the converter. It is found that these converters have more desirable characteristics when operated at a frequency above the resonant frequency rather than below it. Analytical results are verified by sinlulation and experiment.


Coping With The Risk Of Cancer In Children Living Near Power Lines, Eileen N. Abt Jan 1994

Coping With The Risk Of Cancer In Children Living Near Power Lines, Eileen N. Abt

RISK: Health, Safety & Environment (1990-2002)

Ms. Abt briefly summarizes evidence linking power lines with a possible increase in risk of childhood cancer. She also recounts how, although many experts remain skeptical of causality, public fears, whether or not warranted, have themselves created serious problems. Finally, she proposes ways to address those problems.


A Study Of Dc Permanent Magnet Motor Noise Related To Line Current, Candace Rogers Suriano Jan 1994

A Study Of Dc Permanent Magnet Motor Noise Related To Line Current, Candace Rogers Suriano

Department of Electrical and Computer Engineering Technical Reports

Lightweight, compact and inexpensive DC permanent magnet motors are well suited for low cost high production use in industry. Unfortunately, the audible noise emanating from these motors can cause a false negative perception of the motor's quality. In cars, for example, fan motor noise can be a nuisance. The objective of this thesis is to examine the connection between motor noise and the line current wave form for a specific four pole DC permanent magnet motor. It is further concerned with identifying the underlying factors which influence the line current ripple. An audible noise to motor current transfer function is …


An Analysis Of The Payback Potential Of New Lighting Technology, James L. Cox Jan 1994

An Analysis Of The Payback Potential Of New Lighting Technology, James L. Cox

Masters Theses

Recent, energy saving improvements in lighting technology have been made involving the use of more efficient lamps, silver coated light reflectors, and electronic light ballasts. Research indicates that it is economically feasible to retrofit existing light fixtures to utilize the advantages of these developments. This process consists of the removal of all standard lamps and ballasts in each light fixture, the installation of a highly refined light reflector and the replacement of the existing lamps with brighter, more efficient ones. Standard magnetic ballasts are exchanged for more efficient electronic ballasts. Resulting is a light fixture that produces a comparable amount …


Low‐Cost Technique For Preparing N‐Sb2S3/P‐Si Heterojunction Solar Cells, O. Savadogo, K. C. Mandal Jul 1993

Low‐Cost Technique For Preparing N‐Sb2S3/P‐Si Heterojunction Solar Cells, O. Savadogo, K. C. Mandal

Faculty Publications

No abstract provided.


Losses In Electric Power Systems, E. Benedict, T. Collins, D. Gotham, S. Hoffman, D. Karipides, S. Pekarek, R. Ramabhadran Dec 1992

Losses In Electric Power Systems, E. Benedict, T. Collins, D. Gotham, S. Hoffman, D. Karipides, S. Pekarek, R. Ramabhadran

Department of Electrical and Computer Engineering Technical Reports

This report concerns losses in power systems. The report was assembled by seven authors in EE 532 class at Purdue University in December, 1992. The work was part of a class project on losses . All aspects of losses are discussed from the transmission system through utilization stages. High efficiency motors and lighting are also considered . The students participating in this project also videotaped presentations on power system losses .


Transient Stability Test Systems For Direct Stability Methods, V. Vittal, D Martin, R Chu, J Fish, J C. Giri, C K. Tang, F. Eugenio Villaseca, R G. Farmer Feb 1992

Transient Stability Test Systems For Direct Stability Methods, V. Vittal, D Martin, R Chu, J Fish, J C. Giri, C K. Tang, F. Eugenio Villaseca, R G. Farmer

Electrical and Computer Engineering Faculty Publications

A standard set of power system data with benchmark results are presented against which direct stability techniques to assess transient stability can be compared and tested. The test systems have been selected to display a wide range of dynamic characteristics to provide a robust test of the efficacy and accuracy of the various analytical techniques to analyze transient stability. Transient stability test system data and benchmark results obtained from two commercially available time-domain stability analysis packages are presented


Studies Of High Field Conduction In Diamond For Electron Beam Controlled Switching, R. P. Joshi, M. K. Kennedy, K. H. Schoenbach, W. W. Hofer Jan 1992

Studies Of High Field Conduction In Diamond For Electron Beam Controlled Switching, R. P. Joshi, M. K. Kennedy, K. H. Schoenbach, W. W. Hofer

Bioelectrics Publications

Experimental studies on a vertical metal‐diamond‐silicon switch structure have been conducted for potential pulsed power applications. Both the dc current‐voltage characteristics and the transient switching response have been measured for a range of voltages. With a 1 μm diamond film, the switch has been seen to withstand electric fields up to 1.8 MV/cm. Our results show a polarity dependence which can be associated with current injection at the asymmetric contacts. Polarity effects were also observed in the presence of e‐beam excitation, and arise due to nonuniform carrier generation near the diamond‐silicon interface. Our switching transients were seen to follow …


A New Method For Calculating The Economic Benefits Of Varying Degrees Of Power Factor Correction For Industrial Plant Loads, Mohammed Ishaque Jan 1992

A New Method For Calculating The Economic Benefits Of Varying Degrees Of Power Factor Correction For Industrial Plant Loads, Mohammed Ishaque

Dissertations and Theses

A comparative study of the economic benefits that can be obtained from different degrees of power factor correction for medium and small scale industrial installations is shown. A new approach for precise calculation of kws and kvars required at different power factors is presented. These calculated values are used to find the return on investments for the capacitors needed for power factor correction. The developed method is easy to use, cost effective, accurate and will help electrical engineers with minimum knowledge of power systems to precisely determine the savings available by improving the power factor of an industrial load.


Back-Contact Vertical-Junction Solar Cell And Method, Michael W. Carver, Edward S. Kolesar Jr. Nov 1991

Back-Contact Vertical-Junction Solar Cell And Method, Michael W. Carver, Edward S. Kolesar Jr.

AFIT Patents

An interdigitated back-contact vertical-junction solar cell which utilizes an anisotropically etched 110-oriented silicon crystal wafer. The cell structure includes rounded corner top edges of the between cell channel walls in order to improve light capturing ability and also has pn-junctions disposed over all of the cavity internal surfaces. Additional pn-junctions are located on the rear surface of the cell array to assist in generated carrier collection into a rear mounted metallic conductor grid. The disclosed cell has desirable transducer efficiency, without the use of anti-reflection coatings, and previous improved physical robustness, and radiation hardening. Fabrication of the cell array includes …


Standardised Control Techniques For Induction Generators In Both Grid-Connected And Isolated Applications, John Brazil, Aidan O'Dwyer, M. Murphy Jan 1991

Standardised Control Techniques For Induction Generators In Both Grid-Connected And Isolated Applications, John Brazil, Aidan O'Dwyer, M. Murphy

Conference papers

Induction generators are particularly suitable for small hydro applications and are widely used at present. However, with conventional grid-connected techniques, it is not always possible to use them in regions with weak grids because of excessive connection transients. Consequently, their many advantages cannot be fully exploited in these regions. Standardised control systems have been developed by ECS for isolated applications of induction generators and these will now be further developed to permit reduced-transient grid connections.


Assessment Of Flat Plate Collectors For Solar Powered Rankine Cycle, Inas Mokbel Ghanem Dec 1990

Assessment Of Flat Plate Collectors For Solar Powered Rankine Cycle, Inas Mokbel Ghanem

Archived Theses and Dissertations

No abstract provided.


An Artificial Neural Approach To The Decomposition Problem, Chandrashekar L. Masti Jul 1990

An Artificial Neural Approach To The Decomposition Problem, Chandrashekar L. Masti

Electrical & Computer Engineering Theses & Dissertations

The goal of this thesis is to develop an artificial neural approach toward addressing the intractability involved with the decomposition problem. The search for the lattice of substitution property (s. p.) partitions essential to decompositions is cast into the framework of constraint satisfaction. An artificial neural network is developed to provide solutions by performing optimization of a mathematically derived objective function over the problem space. The issue of transitivity is verified to belong to a class of problems beyond the scope of solvability for conventional quadratic-order constraint satisfaction neural networks. A theorem is stated and proved establishing that third-order correlations …


Coke Oven Emissions: A Case Study Of Technology-Based Regulation, John D. Graham, David R. Holtgrave Jun 1990

Coke Oven Emissions: A Case Study Of Technology-Based Regulation, John D. Graham, David R. Holtgrave

RISK: Health, Safety & Environment (1990-2002)

After examining and analyzing the experience with coke ovens, the authors conclude that attempts to force technology beyond its demonstrated competence can be both expensive and ineffective in controlling hazards. They also suggest implications for pending proposals to further control air pollution.


Analysis And Development Of A Switched Capacitor Power Supply, John Richard Hackworth Apr 1990

Analysis And Development Of A Switched Capacitor Power Supply, John Richard Hackworth

Electrical & Computer Engineering Theses & Dissertations

The combination of a switched capacitor network and switching power supply techniques can result in a transformer less regulated DC power supply that is small, relatively simple, and efficient. In addition, the output of such a system could be operated over a wide range of common mode voltages. Multiple switched capacitor supplies could be stacked to achieve voltage multiplication.

Although the output of a system of this type is a continuous function, the internal operation must be analyzed in finite time elements. This numerical analysis will be shown in both a mathematical approach and a computer model.


Transient Stability Hierarchical Control In Multimachine Power Systems, A Rubbai, F. Eugenio Villaseca Nov 1989

Transient Stability Hierarchical Control In Multimachine Power Systems, A Rubbai, F. Eugenio Villaseca

Electrical and Computer Engineering Faculty Publications

The authors present the optimal transient stability control problem in a hierarchical structure for multimachine power systems. The two-level structure retains the local closed-loop controls, thereby easing its implementation on existing systems. The formulation accounts for nonlinearities and interconnections, and the optimization of the system transient performance is obtained with less computational effort. Since the computations are distributed among the many local feedback subsystems, the storage and solution times are considerably less than those required by a single overall centralized controller. This advantage becomes much stronger as the system size increases. For illustration purposes, this technique was applied successfully to …


The Application Of The Ordered List Method And The Dynamic Programming To The Unit Commitment, Hoang Uong May 1989

The Application Of The Ordered List Method And The Dynamic Programming To The Unit Commitment, Hoang Uong

Dissertations and Theses

The thesis presents a method of committing generating units in a hydro-thermal power system within practical computer resources such as computer time and data storage.


Feasibility Study Of Maine's Small Hydropower Potential, James D. Sysko Jan 1989

Feasibility Study Of Maine's Small Hydropower Potential, James D. Sysko

Maine Collection

Feasibility Study of Maine's Small Hydropower Potential

Prepared by James D. Sysko, Small Hydro East, for the Maine State Planning Office, Maine Office of Energy Resources, January 1989.

"This study focuses on finding potential hydropower sites of approximately 50 kw to 1000 kw in capacity."



Maine Woodburning Guide, Office Of Energy Resources Jan 1988

Maine Woodburning Guide, Office Of Energy Resources

Maine Collection

Maine Woodburning Guide

State of Maine, Office of Energy Resources,

Augusta, Maine, 1988.

Contents: 1 Safe Installation / 2 Buying Firewood / 3 Efficient Woodburning / 4 New Equipment Developments / 5 Chimney and Stovepipe Cleaning



The Influence Of Transverse Magnetic Fields On The Current-Voltage Characteristics Of Glow Discharges, Thomas J. Powers Jul 1987

The Influence Of Transverse Magnetic Fields On The Current-Voltage Characteristics Of Glow Discharges, Thomas J. Powers

Electrical & Computer Engineering Theses & Dissertations

In low pressure discharges, operated in electronegative gas mixtures to the right of the Paschen curve minimum, the discharge resistance can be increased by application of transverse magnetic fields. In this range of operation, both the mean free path and the larmor radius are small compared to the discharge dimensions. The relationship between the electric field and the magnetic field is therefore controlled by electron- molecule collisional processes. Specifically, the magnetically induced increase in the discharge resistance is caused by a downward shift of the electron energy distribution which leads to an increase in attachment and a reduction in ionization. …


Fast Thermal Generation Rescheduling, F. Eugenio Villaseca, B. Fardanesh Feb 1987

Fast Thermal Generation Rescheduling, F. Eugenio Villaseca, B. Fardanesh

Electrical and Computer Engineering Faculty Publications

A new dynamic programming algorithm for fast rescheduling thermal generation is presented. The savings in computational times are brought about by the introduction of two new techniques: the variable truncation dynamic programming and the limitation of the solution space to be searched. Several examples on a 20 machine system are used to illustrate the application of the algorithm and to show that optimal solutions are obtained at significantly reduced computational times.


Electric Power Transmission & Purchases : Report Of A Study By The Joint Standing Committee On Utilities, 112th Maine Legislature, Maine. Legislature. Joint Standing Committee On Utilities Dec 1986

Electric Power Transmission & Purchases : Report Of A Study By The Joint Standing Committee On Utilities, 112th Maine Legislature, Maine. Legislature. Joint Standing Committee On Utilities

Maine Collection

Electric Power Transmission & Purchases : Report Of a Study By the Joint Standing Committee on Utilities, 112th Maine Legislature

Maine Legislature. Joint Standing Committee on Utilities.

Augusta, Maine (December 2, 1986).

Contents: Introduction / Issues & Recommendations / Review of 1986 Legislation / Maine's Electric Power Picture / Technical Analysis of Transmission & Wheeling / Economic Implications of Transmission & Wheeling /. Legals Analysis of Transmission & Wheeling / Proposed Legislation / Appendices / Tables & Figures


An Investigation Of Overvoltage Effects On A Gas-Blown Spark Gap, Michael Steven Mazzola Oct 1986

An Investigation Of Overvoltage Effects On A Gas-Blown Spark Gap, Michael Steven Mazzola

Electrical & Computer Engineering Theses & Dissertations

This experimental investigation addresses the anomalous overvoltage breakdown and subsequent recovery characteristics observed in gas-blown spark gaps. Previous investigations have reported a two-stage recovery process in self-break, pulse-charged, gas-blown spark gape in which the spark gap recovers first to an intermediate breakdown strength before recovering to the undisturbed breakdown voltage. The recovery process has been explained in terms of two different characteristic times. The first is that required to obtain initial recovery in which the spark gap regains its intrinsic breakdown strength. The second time is that required to obtain final recovery in which the pulse-charged spark gap regains the …


A Frequency Domain Digital Signal Processor For Laser Velocimeter Systems, Andreas Evangelos Savvakis Oct 1986

A Frequency Domain Digital Signal Processor For Laser Velocimeter Systems, Andreas Evangelos Savvakis

Electrical & Computer Engineering Theses & Dissertations

A new signal processor for laser velocimeter systems is proposed. The proposed processor incorporates automatic initialization, real time operation, and can efficiently process input signals comprised of as low as 150 photons, with mean oscillation frequency up to 100 MHZ, and input turbulence from 0 to 20%. A bank of digital bandpass filters is employed for the energy spectrum estimation of the input signal. A deterministic model is developed to describe the relationship between the filter output energies and the input signal parameters. The input frequency is estimated by linearly weighting the filter output energies. A spline function approximation approach …


Maine Yankee Shutdown Assessment: A Report To Governor Joseph E. Brennan, Maine State Planning Office May 1986

Maine Yankee Shutdown Assessment: A Report To Governor Joseph E. Brennan, Maine State Planning Office

Maine Collection

Maine Yankee Shutdown Assessment: A Report to Governor Joseph E. Brennan

Maine State Planning Office, Maine Office of Energy Resources, Maine Public Advocate

Executive Department - May 1986

Contents: Legal Process / Decommissioning Constraints and Costs / Public and Economic Costs and Benefits / Apprendices



Two-Step Optimal Thermal Generation Scheduling, B Fardanesh, F. Eugenio Villaseca May 1986

Two-Step Optimal Thermal Generation Scheduling, B Fardanesh, F. Eugenio Villaseca

Electrical and Computer Engineering Faculty Publications

A new approach to the solution of the optimal thermal generation scheduling problem is presented. The problem is solved in two steps. As a first step, the optimal production schedule for the next day is obtained based on a daily load forecast, reserve capacity requirements, and present status of generating units. The second-step algorithm uses the results of the first step and adjusts the previous schedule to meet new constraints developed during the course of the day. Variable truncation dynamic programming is proposed as a new method to reduce computation effort. To eliminate the need for solving the …