Power and Energy Commons^™

Portable Solar Desalination System, Genaro Sanchez, Alan Galarza, Erick Del Real

Electrical Engineering

Clean water and reliable energy can be difficult to obtain in remote locations such as desert villages, secluded islands, and other places where no fresh water can be found. The primary goal for this project is address these problems by implementing a portable desalinization plant system that is to be powered by solar energy PV system as the main energy source.

Sick Laser Scanner Power Supply For Use With A Yamaha Rmax Uav, Elliot Due

Electrical Engineering

No abstract provided.

Wind Power Generator Design For The Dc House Project, Evan Lim, Samson Liu

Electrical Engineering

The purpose of this project is to introduce a cost efficient alternative in converting wind into energy for third world countries.  Currently there are approximately 1.6 billion people who have limited access to electricity. As part of the DC House project, we hope to develop a solution for them as the use of electricity is becoming an essential part of life. One of the natural energy resources to provide power to the DC House is wind. The components used for the project are a DC motor and DC-DC converter to translate wind into power and produce DC voltage and current, …

Variable Dc Voltage Wall Outlet For The Dc House Project, Michael Detmers, Tyler J. Blauvelt

Electrical Engineering

This senior project report will focus on explaining the design and operation of a variable DC wall outlet for use in the DC house. Testing will include the use of various loads using different input DC voltages not exceeding a maximum output of 90W.

The most important aspects of the outlet are to have a highly-efficient converter efficiency as well as system isolation from the main DC bus on the input. This report will outline the purpose and way of achieving isolation through use of a Flyback DC-DC converter. The user interface is the second significant aspect and details of …

60 Watt Embedded Solar Cell Umbrella, Matthew Devoss

Electrical Engineering

No abstract provided.

Solar Instrumentation Lab, Rene Canedo Iii, Rong Gui Chen

Electrical Engineering

This project is a mobile platform that will allow experiments on different solar panels to be done easily while keeping the cost of the lab to a minimum. California Polytechnic State University’s motto is ‘learn by doing’ and this lab structure will allow students to get practical experience with photovoltaic cells and the instruments that are required to take measurements. The solar instrumentation lab is a potential hardware lab for the electrical engineering department’s Sustainable Electric Energy Conversion class EE 420 and Solar-Photovoltaic Systems Design EE 520. This group took the current solar structure as a base for the lab’s …

Cal Poly Power System Design & Analysis, Minesh D. Patel

Electrical Engineering

The scope of this project encompasses the design and analysis of the Cal Poly Power System at the distribution level using the SKM software environment. The purpose is to accurately model the power system in software so theoretical calculations and analysis can be executed. This requires sufficient preliminary research to obtain data for the main buildings on campus, sound interpretation of one line diagrams, designing the system within the software using realistic values and then performing analysis to model real world situations.  The data collected is under maximum load conditions for a specified time period using medium voltage parameters. The …

Exercise Bicycle Dc-Dc Converter For The Energy Harvesting From Exercise Machines Project, Ryan Rickard, Logan Stowe

Electrical Engineering

Project is a continuation of previous projects that seek an efficient DC to DC converter for the existing exercise bicycle system created by Mechanical and Electrical Engineering students. This DC-DC converter is to integrate with the wide range of DC voltages produced by the bicycle in order to produce a constant optimal voltage for charging a car battery. This converter will boost voltages when the bicycle outputs below the optimal voltage and buck voltages when above. The converter will take EHFEM one step closer to its overall and final goal of harvesting energy from the exercise machines in Cal Poly’s …

Brushless Dc Motor Design And Build, Justin Damele

Electrical Engineering

Complete Design and Build of a Brushless DC Motor. Everything was manufactured using various Lathes and End Mills. Everything built from scratch.

Dc House Modeling And System Design, Jessica E. Chaidez

Electrical Engineering

This project entails the study and design of DC power distribution for the DC House Project. Wire size, common high efficient loads, maximum power input, and different distribution system implementation (ring or radial) play a major role when designing an efficient, low-voltage distribution system. Efficiency is determined based on which main bus voltage powers all the loads with minimal power loss. Power efficiency is heavily dependent in DC-DC converter efficiencies due to the power loss in converting the voltage from high to low, or vice versa. Selection of the wire size plays a major role in power losses. There are …

Solar Powered Backpack, Saagar Sabharwal, Tom Poonsopin

Electrical Engineering

One popular motto in electrical engineering today is “going green.” This project will convert the sun’s energy into reusable energy. The purpose of this senior project is to develop a solar powered backpack that can charge certain portable USB devices for students. Many students walk around campus with an iPod or cell phone, which has surely died or ran low on batteries at least once when needed most. This backpack will allow students to charge their devices “on the go.” When students walk or bike around campus, the solar panels attached to the backpack will allow recharging of their portable …

Android Application Controlled Surge Protector, Lok An

Electrical Engineering

A significant amount of consumer electronics cannot be switched off completely without being unplugged. Standby power, also known as phantom power, refers to the electric power consumed by electronic appliances when they are switched off. There are some devices that need constant power; items like alarm clocks and security systems need constant power to function correctly. Some devices, such as video game consoles and televisions, consume power without offering any features. Electricity lost from standby power has been increasing with the amount of consumer electronics increasing in households.

This project’s goal is to create a low power remote that can …

Design And Simulation Of V2g Bidirectional Inverter And Dc-Dc Converter, Allan Agatep, Mason Ung

Electrical Engineering

As plug-in hybrid electric vehicles (PHEV) become more popular, the utility companies are forced to feed the grid more electricity. However, these PHEVs are capable of providing power to the grid when they are parked serving as ancillary systems for grid regulation (V2G). Using a system based on photovoltaic (PV) technology, a design for a bidirectional inverter with LCL filter, and a bidirectional dc-dc with a constant current controller, was constructed using LTspice. Various papers were researched and analyzed to determine applicable designs for components. Simulations show the designs are capable of bidirectional power transfer. ETAP simulations show that delivering …

Development Of Wind Tunnel For Laboratory Wind Turbine Testing, Danny Alexander Zepeda

Electrical Engineering

A wind tunnel with a 0.5 HP motor was purchased by Cal Poly Electrical Engineering Department from Hampden for $16,000. It can only simulate winds of up to 10 MPH. The tunnel has a manual dial that controls the wind speed. It also measures the voltage and current output with an analog measure display. This wind tunnel was expensive and unfortunately cannot achieve very high wind speeds. For this reason, a similar wind tunnel with more potential and with a smaller budget was proposed to be built for use in the Sustainable Energy Lab. The new wind tunnel that was …

Bridgeless Active Power Factor Correction Using A Current Fed Push Pull Converter, Jeramie Seth Bianchi

Master's Theses

ABSTRACT

Bridgeless Active Power Factor Correction

Using a Current Fed Push Pull Converter

Jeramie Seth Bianchi

Switched Mode Power Supplies have become increasingly popular for efficient methods of delivering power to an assortment of electronic devices. This thesis proposes a method of using a current fed push pull converter to provide active power factor correction and rectification in a single stage. While most AC-DC converters utilize a bridge rectifier to convert AC-DC and then perform DC-DC conversion, the proposed circuit will utilize its output diodes to perform rectification, thus eliminating the need for a bridge rectifier. This circuit will also …

Project 308: Augmented Reality Mario Kart, Joseph Abad, David Allender, Joryl Calizo, Ryan Gaspar, Gavin Lee

Computer Engineering

Mario Kart is a popular go-kart racing game developed by Nintendo. The premise of the game is simple: drive a go-kart along a racetrack and reach the finish line before the other players. What makes this game unique, however, is the inclusion of weapons, traps, and other projectiles that a player can use to gain an advantage in the race. We have taken on the challenge of not only recreating this amazing game, but using the art of Augmented Reality to fully immerse the player in the full experience. Rather than play the game on a television screen with a …

Plug-In Hybrid Electric Vehicle Impacts On A Central California Residential Distribution Circuit, Darren Janigian

Master's Theses

The adoption of plug-in hybrid electric vehicles (PHEV) as a means of transportation over conventionally fueled vehicles introduces new challenges to the existing infrastructure of the electrical transmission and distribution system.  PHEV battery charging can represent a significant power demand that has the potential to overload electrical distribution components.  This study examines the impacts of PHEV charging on household service transformers, distribution conductors and voltage levels of a Central California residential distribution system.  The system is simulated using ETAP power system analysis software.  Transformers are the most vulnerable to overloads, especially if PHEV charging occurs in clusters.  Main feeder conductors …

Off-Grid Public Lighting System – Design And Characterization Of An Led Luminaire, Quanghuy Le

Master's Theses

The technological advances made in the photovoltaic industry have led to a vast exploration of self-sustaining systems.  As the consumer demand for electricity rises from increasing population and development of existing technologies, new practices in system designs are required to relieve the impact on the electrical grid.

This thesis delves into a developing concept of using photovoltaic modules for roadway lighting, with emphasis on establishing the fundamental design for a “spot-lighting” luminaire.  By effectively extinguishing various sections of the luminaire in the absence of pedestrian trafficking, the proposed design and implementation will minimize the prolonged costs, as well as the …

Energy Harvesting From Exercise Machines: Forward Converters With A Central Inverter, Nicholas Keith Lovgren

Master's Theses

This thesis presents an active clamp forward converter for use in the Energy Harvesting From Exercise Machines project.  Ideally, this converter will find use as the centerpiece in a process that links elliptical trainers to the California grid.  This active clamp forward converter boasts a 14V-60V input voltage range and 150W power rating, which closely match the output voltage and power levels from the elliptical trainer.  The isolated topology outputs 51V, higher than previous, non-isolated attempts, which allows the elliptical trainers to interact with a central grid-tied inverter instead of many small ones.  The final converter operated at greater than …

Modeling And Analysis Of The Effects Of Pcb Parasitics On Integrated Dc-Dc Converters, Darwin Domingo Fernandez

Master's Theses

Load transients are prevalent in every electronic device including semiconductor memory, card readers, microprocessors, disc drives, piezoelectric devices, and digitally based systems. They are capable of producing voltage stress, introducing noise, and degrading device functionality. In order to avoid damage to the device, a feedback control loop is implemented with system compensation to regulate the output voltage deviations by the converter. Because designing compensation networks can be rather complicated, DC-DC converters with integrated feedback control topologies help minimize design time and complexity of converter compensation at the expense of design flexibility. This thesis widens the limitations of an integrated DC-DC …

Photovoltaic Emulator Adaptable To Irradiance, Temperature And Panel Specific I-V Curves, Joseph Gamos Durago

Master's Theses

This thesis analyzes the design and performance of a photovoltaic (PV) emulator. With increasing interest in renewable energies, large amounts of money and effort are being put into research and development for photovoltaic systems. The larger interest in PV systems has increased demand for appropriate equipment with which to test PV systems.

A photovoltaic emulator is a power supply with similar current and voltage characteristics as a PV panel. This work uses an existing power supply which is manipulated via Labview to emulate a photovoltaic panel. The emulator calculates a current-voltage (I-V) curve based on the user specified parameters of …

Synthesis And Catalytic Property Of Flaked Spindle-Like Cuo Nanocrystals, Jian-Feng Fan, Li-Qing Li, Yu-Feng Huang, Lou-Zhen Fan

Journal of Electrochemistry

A simple and efficient electrochemical route was developed for the synthesis of flaked spindle-like CuO nanocrystals using aqueous electrolyte and Cu sacrificial anode (graphite as the cathode) in an undivided cell at a constant potential mode under room temperature. The morphologies, structure and component of CuO nanocrystals obtained were characterized by SEM, XRD, respectively. Flaked spindle-like CuO nanocrystals were successfully used to modify a GC electrode to detect H₂O₂ with cyclic voltammetry (CV) and amperometric (AC).The results showed that products were pure monoclinic CuO nanocrystals. The linear range for the determination of hydrogen peroxide is from 1.0 …

Detection Of Acute Promyelocytic Leukemia Pml/Rarî± Fusion Gene Using Graphene Modified Glassy Carbon Electrode, Zhi-Xian Lian, Guang-Xian Zhong, Kun Wang, Ai-Lin Liu, Xin-Hua Lin, Yuan-Zhong Chen

Journal of Electrochemistry

A graphene modified glassy carbon electrode (GCE) was prepared by electrochemical reduction of graphite oxide fixed on the surface of GCE. Then, the amino-group modified probe of acute promyelocytic leukemia (APL) PML/RARα fusion gene fragment was immobilized onto surface of the graphene modified GCE by coupling activating agent. With methylene blue (MB) as a novel electrochemical indicator, artificial APL PML/RARα fusion gene fragment was measured by differential pulse voltammetry (DPV). The result indicated graphene nanomaterial showed good sensitization on the signal of MB. The relationship between the reduction peak current of MB and the concentration of complementary strand was linear …

Influence Of Tert-Butylpyridine On The Band Energetics Of Nanostructured Tio2 Electrodes And The Photoelectrochemical Properties Of Dye-Seneitized Electrodes, Shu-Ming Yang, Ji-Chao Wang, Hui-Zhi Kou, Hong-Bin Xue, Hong-Jun Wang, Yu-Ling Guo

Journal of Electrochemistry

The flat band edges (Efb) of nanostructured TiO₂ electrodes in electrolyte solutions with tert-butylpyridine (TBP) of different concentrations have been determined with spectroelectrochemical technique. TBP played a role in band energetics of nanostructured TiO₂ electrodes. The Efb values of -2.25, -2.46 and -2.62 V were determined in three 0.2 mol•L^-1 tetrabutylammonium perchlorate (TBAP) acetonitrile electrolytes which contain 0, 0.2 and 0.4 mol•L^-1 TBP respectively. The addition of Li+ ions shifted Efb positively. The Efb values of -1.12, -1.22 and -1.30 V were determined in three 0.2 mol•L^-1 LiClO₄ acetonitrile electrolytes which contain 0, 0.2 …

Dft Study Of Co2 Reduction To Hydrocarbons On Cu Surfaces, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

CO₂ reduction on Cu(111) single crystal surfaces was studied using DFT calculations on the reaction energies and the minimum energy paths. The results indicated that the possible reaction paths for CO₂ reduction on Cu(111) surface are CO₂(g) + H* → COOH* → (CO +OH)*, (CO + H)* → CHO*, CHO + H → CH₂O* → (CH_2⁺O)*, CH₂* + 2H* → CH₄ or 2CH₂* → C₂H₄. On Cu(111) surface, the reaction rate is controlled by steps of CH₂O* → (CH_{2 …}

Preparation And Performance Of Carbon-Coated Si/C Composites, Li-Li Du, Quan-Chao Zhuang, Tao Wei, Yong-Li Cui, Zhi Sun, Shi-Gang Sun

Journal of Electrochemistry

Si/C composite for lithium ion batteries was obtained by pyrolyzing and ball-milling. The microstructure and component of the composite was characterized by SEM and XRD, the electrochemical performance was investigated by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and galvano static charge-discharge tests. The results illustrate that the particle of Si/C composite prepared by pyrolysis exhibits inerratic morphology, uniform carbon-coating layer, good electrical conductivity, low resistance. The first intercalated-lithium capacity of the composite material is 4495 mAh/g; the first coulomb efficiency is 65.3%. From the second week the coulomb efficiency maintains 97%, and the capacity at the 100th cycle can …

Research Progress In Orthosilicates As Cathode Materials For Li-Ion Batteries, Dong-Ping Lv, Lin Wang, Yong Yang

Journal of Electrochemistry

Rechargeable Li-ion batteries fulfilling high-energy density, high safety, environmental friendliness, and low cost are demanded urgently for energy storage systems. Besides the structure stability arising from the strong Si-O covalent bond, environmental benignancy and low cost from the characteristics of Fe, Mn, Si elementals, orthosilicates (Li₂MSiO₄) show promising prospect to meet the demand of high-energy density for its two available Li+ per formula unit. Motivated by these significant advantages, Li₂MSiO₄ have been intensively investigated in the past few years. In the present work, we gave a review on the progress of orthosilicate research …

Effect Of Pore Size On Pseudo-Capacitive Performance Of Nio In The Mixed Electrolyte Of Koh And Hexacyanoferrate, Wen Wu, Meng-Yan Hou, Dan-Dan Zhou, Yong-Yao Xia

Journal of Electrochemistry

In this paper, five kinds of NiO samples with different pore size distributions were synthesized .The electrochemical capacitance of the samples were characterized in 3 mol/L KOH solution with and without hexacyanoferrate addition. Electrochemical test results indicated the NiO sample with an optimum pore size of about 15 nm shows high Coulombic efficiency of the N₄(NiO) electrode as the redox reaction of hexacyanoferrate ions would be limited in the pore, thus prevent ion diffusion into the bulk electrolyte solution .

Investigation Of Supercapacitors Based On Polyvinyl Alcohol Hydrogel-Polymer Electrolyte, Kai-Qing Xu, Le-Qing Fan, Ji-Huai Wu, Qing Leng, Xin Zhong, Jian-Ming Lin, Miao-Liang Huang, Zhang Lan

Journal of Electrochemistry

For the first time, the supercapacitor based on the hydrogel-polymer electrolyte which consisted of the cross-linking of polyvinyl alcohol-glutaraldehyde (PVA-GA) using 2-acrylamido-2-methyl propane sulfonic acid (AMPS) as solicitation reagent was assembled. The gel polymer electrolyte was characterized by FTIR and AC impedance. The maximum ionic conductivity is 1.23 mS/cm at room temperature. The electrochemical properties of the supercapacitor were investigated by cyclic voltammetry, AC impedance spectra and constant current charge-discharge curve. The results show that the specific capacitance reachs 139 F/g with AMPS of 1.0 g and 0.05 mL of 5 %(by mass) GA. And the specific capacitance still retained …

Study On Direct Electro-Oxidation Of Anisaldehyde, Lin-Lin Wu, Ying-Hong Zhu, Shan-Shan Li, Hong-Yan Zeng, Chun-An Ma

Journal of Electrochemistry

The oxidation of anisole on Pt electrode was investigated by cyclic voltammery and constant potential electrolysis. The influence of scan rates, substrate concentration, supporting electrolytes and solvent were considered . The results show that the electro-oxidation process of anisole was irreversible. In this research the sulfuric acid was the best supporting electrolytes and acetone was the best solvent, and the process was controlled by diffusion . The product of constant potential electrolysis was charactered by GC-MS .The results show that the main products was anisaldehyde, and the selectivity was up to 66.5% when using acetone as solvent.