Power and Energy Commons^™

Coupled Electromagnetic And Heat Transfer Model For Microwave Heating In Domestic Ovens, Krishnamoorthy Pitchai, Sohan Birla, Jeyamkondan Subbiah, D. D. Jones, Harshanardhan Thippareddi

Department of Food Science and Technology: Faculty Publications

Microwave ovens are used extensively for heating a variety of not-ready-to-eat food products. Non-uniform heating of foods in microwave ovens is a major concern in assuring microbiological safety of such products. The non-uniform heating of foods is attributed by complex interaction of microwaves with foods. To understand this complex interaction, a comprehensive model was developed to solve coupled electromagnetic and heat transfer equations using finite-difference time-domain based commercial software. The simulation parameters, cell size, heating time step, and number of iterations for steady state electromagnetic field were optimized. The model was validated by 30 s heating profile of a cylindrical …

Fuzzy Interference System In Energy Demand Prediction, Thair Mahmoud, Daryoush Habibi, Octavian Bass, Stefan Lachowicz

Research outputs 2012

No abstract available.

Modeling And Analysis Of Grid-Connected Solar-Wind Hybrid Power System, Sultan Altamimi

Dissertations and Theses @ UNI

Renewable energies are considered to be a significant part of the energy mix to assist the existing electricity demand and the future of electrical generation. Electrical power simulation software is increasingly being used to answer and determine the source of potential problems in the actual power system. To have a better understanding of an electrical power system, it is essential to validate all the components through simulation within an environment that allows accurate modeling of all power system components. This research presents modeling and analysis of an actual grid-connected solar-wind hybrid system at University of Northern Iowa campus in Cedar …

Measuring And Filtering Microwave Radiations Using Frequency Selective Surface Through Energy Saving Glass, Irfan Ullah

Theses: Doctorates and Masters

This thesis presents the results of our investigation into the measurement and filtering of microwave radiation, and the subsequent development of a microwave reduction solution for modern building architecture utilising Energy Saving Glass (ESG), in conjunction with Frequency Selective (FSS) surfaces through which useful signals can be filtered. In the investigation, radiation power density levels arising from the three common microwave sources (radio base stations, mobile phones, and microwave ovens) were measured, and the results were compared with the standards provided by the Australian Radiation Protection and Nuclear Safety Agency. For the radio base stations, the relationship between radiation intensity …

The Integration Of Wind Energy In The Electrical Grid During The Contingencies, Islam Ali

Dissertations and Theses @ UNI

As wind energy expansion develops, there are also many problems and challenges to connect the wind farms to the grid. There are many different interactions during the connection like the voltage flicker, harmonics, transient, short circuit current, frequency, and safety protection. Those problems may affect the performance of the grid and may cause serious problems. This study investigates the grid-connection problems for the wind turbines and offers appropriate solutions. This study provides a simulation for the power system during the faults. The electrical grid in the simulation contains generators and wind turbines which are connected to the grid. It also …

Adaptive Mitigation In The Electric Power Sector, Lesley K. Mcallister

BYU Law Review

No abstract provided.

Identification Of Power System Stability Using Relevant Modes, Rogers Whitlock Jr

LSU New Orleans Theses and Dissertations

The purpose of this investigation is to identify appropriate location of capacitor banks and sources of reactive power by studying power system stability in the vicinity of system equilibrium states. The locations for reactive power sources are determined by identifying those modes of the system that participate most in the system behavior in general and in dictating the final state of the system after experiencing faults or disturbances. To identify the relevant modes of the system that participate most in the system dynamic, we shall make use of modal and participation analysis for different system conditions. We also apply modal …

Lithium-Based Battery System Management And Balancing, William Joel Schmidt Iii

Purdue Polytechnic Masters Theses

This thesis builds upon previous work completed for the design and evaluation of active lithium battery system management. Simulations were performed to provide a comparison for the hardware that was designed, built, and tested. An analysis of the simulation and hardware results was completed to support or disprove the initial hypothesis. A DC-DC converter was used as the source for the balancing current. Lithium polymer batteries with a 5Ah capacity were used for testing the designed hardware. The findings showed that there is a reduction in the system voltage swing during balancing as well as less time taken to decrease …

Integration Of Upqc For Power Quality Improvement In Distributed Generation Network – A Review, Shafiuzzaman Khan Khadem, Malabika Basu, Michael Conlon

Conference Papers

In this paper a technical review of the integration of a Unified Power Quality Conditioner (UPQC) in a distributed generation network is presented. Although the primary task of UPQC is to minimize grid voltage and load current disturbances along with reactive and harmonic power compensation, additional functionalities such as compensation of voltage interruption and active power transfer to the load and grid have also been identified. Connection methodologies with their advantages and disadvantages are also described. Recent improvements in capacity expansion techniques and future trends for the application of UPQC in distributed modes are also identified.

Highly Efficient Maximum Power Point Tracking Using A Quasi-Double-Boost Dc/Dc Converter For Photovoltaic Systems, Christopher J. Lohmeier

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Solar photovoltaic (PV) panels are a great source of renewable energy generation. The biggest problem with solar systems is relatively low efficiency and high cost. This work hopes to alleviate this problem by using novel power electronic converter and control designs. An electronic DC/DC converter, called “Quasi-Double-Boost DC/DC Converter,” is designed for a Solar PV system. A Maximum Power Point Tracking (MTTP) algorithm is implemented through this converter. This algorithm allows the PV system to work at its highest efficiency. Different current sensing and sensorless technologies used with the converter for the MPPT algorithm are offered and tested. Design aspects …

Digitally Controlled, Modular Electronic Load, Jason L. March

Master's Theses

This project entails the design and development of a digitally controlled, modular electronic load. The proposed load is unique from existing designs because it has the added ability to increase its maximum current level by adding identical modules in parallel. Each module is designed to sink a maximum of 5A at 60V but more modules allow for more current. The cost and simplicity of the design are considered such that it can be reproduced in-house to replace, whenever possible, the resistor box for load testing of any analog circuits but more specifically power electronic circuits.

The design process as well …

Energy-Based Analysis Of Utility Scale Hybrid Power Systems, Kwame Agyenim-Boateng

UNLV Theses, Dissertations, Professional Papers, and Capstones

The promise of large-scale use of renewables such as wind and solar for supplying electrical power is tempered by the sources' transient behavior and the impact this would have on the operation of the grid. Among the methods cited for addressing some of those concerns are exploring the complementary nature of solar and wind power generation, and through the use of supplemental energy storage. While the technology for the latter has not been proven to be economical on a large scale at the present time, some assessments of what magnitude is required can be made. An energy-based analysis of utility …

Matlab/Simulink Implementation And Analysis Of Three Pulse-Width-Modulation (Pwm) Techniques, Phuong Hue Tran

Boise State University Theses and Dissertations

With advances in solid-state power electronic devices and microprocessors, various pulse-width-modulation (PWM) techniques have been developed for industrial applications. For example, PWM-based three-phase voltage source inverters (VSI) convert DC power to AC power with variable voltage magnitude and variable frequency.

This thesis discusses the advantages and drawbacks of three different PWM techniques: the sinusoidalPWM(SPWM) technique, the third-harmonic-injection PWM(THIPWM) technique, and the space-vector PWM (SVPWM) technique. These three methods are compared by discussing their ease of implementation and by analyzing the output harmonic spectra of various output voltages (poles voltages, line-to-neutral voltages, and line-to-line voltages) and their total harmonic distortion (THD). …

Fabrication Of Composite Nanomaterials For Thin Film Amorphous Silicon Solar Cells, Benjamin Seth Newton

Graduate Theses and Dissertations

A material with the precise combination of amorphous silicon and polycrystalline silicon would be able to take advantage of the high absorption capabilities of amorphous silicon and the electron transport capabilities of polycrystalline silicon. Polycrystalline nanostructures in the form of wires can also take advantage of other properties of light absorption, trapping and scattering inherent in nanowire structures. These properties of high absorption and electron transport in one device would lead to advances in the search for highly efficient low cost solar cells and sensors. In this work a thin film material composed of an array of polycrystalline silicon nanostructures …

Modeling And Analysis Of A Four-Switch Buck-Boost Dynamic Capacitor, Oscar Plasencia

Master's Theses

Modern electric power utilities are facing a variety of challenges introduced by the increasing complexity of their operation, structure, and consumer loads. One such challenge has been to supply the ever growing demand for reactive power which is essential for grid support. For this reason dynamic VAR technologies are becoming much more important to modern day power systems. A recent dynamic VAR technology known as the Dynamic Capacitor offers full quadrant capacitive VAR control through the combination of AC/AC buck and boost cells. This paper introduces a new topology deemed the “Four-Switch Buck-Boost Dynamic Capacitor” which promises to combine the …

In-Situ Ellipsometry Characterization Of Anodically Grown Silicon Dioxide And Lithium Intercalation Into Silicon, Eric A. Montgomery

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, in-situ ellipsometry and electroanalytical investigations of two electrochemical processes are reported: including the formation of anodically grown silicon dioxide and the intercalation of lithium into silicon. Analysis of the ellipsometry data shows that the anodically grown silicon dioxide layer is uniform and has similar properties as thermally grown silicon dioxide. The lithium-ion intercalation data reveals non-uniform thin film formation, which requires further studies and development of appropriate ellipsometric optical models.

Advisers: Eva Schubert and Mathias Schubert

Preparation And Application Of Nano-Nio As Anode In Lithium-Ion Batteries, Cheng-Dong Bai, Jia-Jia Chen, Qi Zhang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

In this work, the nano-NiO material was prepared by hydrothermal method. The surface morphologies and electrochemical properties of nano-NiO material were investigated. The special nano-NiO material with porous surface assembling honeycombs(100-200nm) was obtained by using surface active agents. The discharge capacity of nano-NiO electrode up to 2385.7 mAh/g was achieved at current density of 0.1A/g in the first circle,while 1100mAh/g could be maintained after 100 circles. At current density of 2.0A/g, the discharge capacity of 600 mAh/g was obtained. And when the current density was reduced to 0.1A/g, the discharge capacity was restored to 1050 mAh/g. The nano-NiO electrode exhibited …

Microemulsion Preparation And Electrochemical Characterization Of Pt/C, Ptir/C Electrocatalysts, Ya-Ping Zeng, Sheng Sui

Journal of Electrochemistry

The Pt/C electrocatalysts were prepared by three different systems and the PtIr/C electrocatalysts were prepared with four different Ir contents. The samples were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), cyclic voltammetry (CV), potentiostatic and potentiodynamic polarizations measurements. The experimental results confirmed that the electrocatalyst particles prepared by the microemulsion method were well distributed on XC-72R supports with the active particle sizes of 5～10nm and good electrocatalysts activity. The Pt85Ir15/C electrocatalysts showed the highest overall electrochemical activity in unitized regenerative fuel cell.

A Brief Review Of Research Progress In The Development Of Engineering Models For Lithium Ion Batteries, Da-Wei Wang, Dong-Jiang Li, Jun Li, Yong Yang

Journal of Electrochemistry

Lithium ion battery has become an important and popular electrochemical device for energy storage.Suitable evaluation and understanding of electrochemical performance and state of charge play a key role in the applications of lithium ion batteries.Construction and utilization of engineering modeling for lithium ion batteries is an effective way to fulfill this target.In this paper,engineering models of lithium ion batteries based on electrochemical reaction,ionic diffusion and migration are introduced.The emphasis is placed on the development of engineering models by the introduction of side reaction,phase transition,stress and energy.The applications of engineering models in such simulations as charge-discharge,concentration distribution,current distribution,state of charge,stress and …

The Electrochemical Properties Of Cathode Materials LimXV3-XO8, Hui Yang, Gang-Gang Zhao, Juan Li

Journal of Electrochemistry

The cathode material of LiM_xV₃-xO₈ was fabricated by sol-gel method using citric acid as a chelating agent and doping transition metal ions M (Mn, Ti, Co and Ni). The structure, morphology and electrochemical proprieties of the LiMxV3-xO8 samples were investigated by XRD, TGA/DTA, SEM, charge-discharge and CV measurements. The results showed that different calcining temperatures result in different structures and morphologies, which lead to different discharge capacities. The specific discharge capacity of the sample calcined at 500℃ for 6 h was up to 300.4 mAh/g in the first cycle, and the capacity decreased with the …

Electrochemical Properties Of Tungstogermanate And Electrocatalysis Of H2O2 On Gew11Co/P-Opd/Gc Electrode, Li-Li Zhu, Jian-Ying Qu, Jue Wang, Hao-Yue Feng

Journal of Electrochemistry

The electrochemical properties of Co-substituted trimeric tungstogermanate containing Keggin fragments were studied. Cyclic voltammograms revealed two couples of reversible redox peaks on glassy carbon (GC) electrode in acid solutions. They corresponded to two-electron reductions accompanying by the additions of four protons and three protons, respectively, both were controlled by adsorption. The differences in the peak potentials of 2-electron-4-proton and 2-electron-3-proton reactions were 31 mV and 35 mV, respectively..Furthermore, the tungstogermanate (GeW11Co) modified GC electrode with functionalization by poly(o-phenylenediamine) (P-oPD) was prepared readily by electropolymerization. The GeW11Co/P-oPD/GC electrode could electrocatalyze the reduction of hydrogen peroxide, which showed good stability and quick …

Preparation And Capacitance Characteristics Of Nickel Oxide Electrode With Mesh-Like Structure, Hui Xu, Zhen-Jun Peng, Dong-Hong Guo, Jun-Ling Li

Journal of Electrochemistry

The mesh-like structure of NiO electrode was obtained by first preparing the precursors via hydrothermal process using nickel sulfate and carbamide as reactants, sodium hexametaphosphate as a surfactant, and followed by calcination of the precursors at 400 ℃. The structure, morphology and capacitance characteristics of NiO electrode were characterized by XRD, SEM and constant current charge-discharge testing techniques. The effects of hydrothermal temperatures on the electrochemical properties of NiO electrode were investigated. The results showed that the better property of nickel oxide was obtained when the mole ratio of nickel to urea was 1:4 and the hydrothermal temperature was 140℃. …

Electrocatalytic Determination Of 15 Kinds Of Phenolic Compounds By Novel Gold Nanoparticles-Modified Glassy Carbon Electrode, Yan-Ping Cui, Wei-Xing Wang, Chang-Zhu Yang, Wen-Hong Pu

Journal of Electrochemistry

A gold nanoparticles modified glassy carbon electrode (Au/GCE) was used to detect 15 kinds of phenolic compounds. In the cyclic voltammetry measurements, the peak currents of phenolic compounds at Au/GCE were all increased as compared with GCE and planar gold electrodes, and the oxidation potentials were determined by the activity of analytes. Besides, electrocatalysis of salicylic acid was studied at Au/GCE. The results showed that, there was a good linear relationship between the oxidation current and the concentration of salicylic acid, and the current sensitivity was 1.8 fold higher than that obtained on GCE. Trace phenolic compounds determination could be …

Preparation And Characterization Of Casno3 Anode Material For Lithium Ion Batteries, Ran Sun, Zi-Geng Liu, Ya-Qi Jiang

Journal of Electrochemistry

In this study the precursor CaSn(OH)₆ was prepared via a hydrothermal process, and its composition, surface feature and phase-transition were characterized by XRD, SEM and DSC-TGA. The shapes of CaSn(OH)₆ crystals were effectively controlled by adjusting the volumn ratio of H₂O and CH₃CH₂OH solvents. Perovskite CaSnO₃ could be obtained by calcination of CaSn(OH)₆ at 800 ℃. The reversible capacity of 334.4 mAh/g with good cycling stability could be achieved with the CaSnO₃ electrode.

Preparation And Characterization Of The Lani0.6Fe0.4O3-δ Cathode For Intermediate Temperature Solid Oxide Fuel Cell, Hang Liu, Bo Huang, Xin-Jian Zhu

Journal of Electrochemistry

The LaNi_0.6Fe_0.4O_3-δ as cathode material for intermediate temperature solid oxide fuel cell was prepared using a combustion synthesis technique. The X-ray diffraction (XRD) pattern showed that the single-phase LaNi_0.6Fe_0.4O_3-δ perovskite could be obtained after heat treatment at 600°C. The TEM and SEM images of the synthesized powders revealed that the grains were 50-100nm. According to the electrochemical impedance spectra (EIS), the polarization resistance of the symmetric cell LaNi_0.6Fe_0.4O_3-δ/ScSZ/LaNi_0.6Fe_0.4O_3-δ sintered at 1050°C was the smallest (0.70Ω·cm², 0.27Ω·cm^{2 …}

Dynamic Modeling And Characteristic Analysis Of Proton Exchange Membrane Fuel Cell, Qiu-Hong Jia, Ming Han, Bin Deng, Cai-Zhi Zhang

Journal of Electrochemistry

In this paper, a dynamic model of PEMFC is developed to estimate the dynamic performance of PEMFC by analyzing in detail the influence factors of voltage of PEMFC including various losses. The partial pressure of hydrogen and oxygen is obtained using the differential form of the ideal-gas equation in this model. The steady-state model is obtained by setting reasonable parameter values. The simulation results and experimental results have good consistency, which shows that the simulation model is correct, reasonable and effective. It analyzed the dynamic response characteristics of the output voltage and the partial pressure of hydrogen in condition of …

Indirect Electrochemical Reduction And Cotton Dyeing Process In Fe(Ⅲ)-Oxalate-Calcium Gluconate System, Qing-Zhi Wang, Wei Wang

Journal of Electrochemistry

The electrochemical behavior and possible reaction mechanism in Fe(Ⅲ)-oxalate-calcium gluconate system were studied by cyclic voltammetry. The results showed that Fe(Ⅱ)-gluconate was the final reductant. The reduction time, the working voltage and the cathode area influenced the current efficiency. The high current efficiency of 89% for the indirect electrochemical reduction of Vat Scarlet R could be achieved with reduction time of 10 min, working voltage of 4 V and cathode area of 40 cm² in Fe(Ⅲ)-oxalate-calcium gluconate system.

Impacts Of Plug-In Electric Vehicle On Residential Electric Distribution System Using Stochastic And Sensitivity Approach, Henry Chigozie Ureh

Master's Theses

Plug-in Electric Vehicles (PEVs) are projected to become a viable means of transportation due to advances in technology and advocates for green and eco-friendly energy solutions. These vehicles are powered partially, or in some cases, solely by the energy stored in their battery packs. The large sizes of these battery packs require large amount of energy to charge, and as the demand for PEV increases, the increase in energy demand needed to recharge these PEV batteries could pose problems to the present electric distribution system. This study examines the potential impacts of PEV on a residential electric distribution system at …

Electron Energy Distribution Control, Wade Harlow

Von Braun Symposium Student Posters

No abstract provided.

Development And Prototyping Of A Ground Fault Circuit Interrupter For 3-Phase 480 Volt Systems, Matthew R. Norlander

Master's Theses

Ground Fault Circuit Interrupter (GFCI) technology was first introduced in the NEC in 1971, yet four decades later the technology has not been introduced to a great extent outside of the home environment. This thesis introduces the difficulties encountered in low-voltage three phase ground fault current detection, and adopts a previously patented tripping scheme to develop and prototype a digital relay for 3-phase 480 volt systems capable of the sensitivity and speed required for personnel safety. Results demonstrate the feasibility of the concept and suggest commercial development should be pursued. The prototype is capable of mA sensitivity and reliably detects …