Power and Energy Commons^™

Model-Based Condition Monitoring And Power Management For Rechargeable Electrochemical Batteries, Taesic Kim

School of Computing: Dissertations, Theses, and Student Research

Rechargeable multicell batteries have been used in various electrical and electronic systems, e.g., renewable energy systems, electric-drive vehicles, commercial electronics, etc. However, there are still concerns about the reliability and performance degradation of rechargeable batteries caused by low thermal stability and the aging process. A properly designed battery management system (BMS) is required for condition monitoring and control of multicell batteries to ensure their safety, reliability, and optimal performance. The goal of this dissertation research was to develop a novel BMS for rechargeable multicell batteries.

First, this research developed high-fidelity battery models for online condition monitoring and power management of …

Secondary Re-Use Of Batteries From Electric Vehicles For Building Integrated Photo-Voltaic (Bipv) Applications, Fintan Mcloughlin, Michael Conlon

Reports

PV Crops is evaluating the use of battery technologies such as Vanadium Redox within Building Integrated Photovoltaic (BIPV) applications. However, their inclusion into BIPV systems will inevitably raise the overall costs of such systems. As a result, PV Crops is looking at other measures in parallel to help lower the costs associated with such systems. One particular area of interest is the potential secondary re-use of battery technology from Electric Vehicle (EV) market as a way of mitigating high costs of such systems as well as a means of encouraging battery recycling.

The global installed capacity for Photovoltaic’s (PV) connected …

Offshore Electrical Networks And Grid Integration Of Wave Energy Converter Arrays - Techno-Economic Optimisation Of Array Electrical Networks, Power Quality Assessment, And Irish Market Perspectives, Fergus Sharkey

Doctoral

Wave energy is an emerging industry and faces many challenges before commercial wave energy converter (WEC) arrays are installed. One of these challenges is the grid integration of WEC arrays. This includes offshore electrical networks, grid compliance, and access to electrical markets. This must be achieved in a technically viable manner and also at an acceptable cost. As electrical networks are expected to make up a large proportion of the overall WEC array CAPEX, perhaps up to 25%, this area is critical to the long term competitiveness of wave energy.

The objectives of this thesis are to develop technically and …

Data Cleaning In The Energy Domain, Hermine Nathalie Akouemo Kengmo Kenfack

Dissertations (1934 -)

This dissertation addresses the problem of data cleaning in the energy domain, especially for natural gas and electric time series. The detection and imputation of anomalies improves the performance of forecasting models necessary to lower purchasing and storage costs for utilities and plan for peak energy loads or distribution shortages. There are various types of anomalies, each induced by diverse causes and sources depending on the field of study. The definition of false positives also depends on the context. The analysis is focused on energy data because of the availability of data and information to make a theoretical and practical …

Load Frequency Control Of Battery Based Energy Storages, Neeru Saini

Theses and Dissertations

This work is the study of potential applications of battery-based energy storages in the power system so that the performance can be improved. The research is focused on the case where batteries are installed at the load side. Such a battery works like an energy buffer between power system and a load. It is possible to control the battery charging time based on the status of the power system operation and the state of charger of the battery so that the power flow in the power system can become more stable. The strategy of load frequency control (LFC) was investigated …

Vortex Identification In The Wake Of A Wind Turbine Array, Aleksandr Sergeyevich Aseyev

Dissertations and Theses

Vortex identification techniques are used to analyze the flow structure in a 4 x 3 array of scale model wind turbines. Q-criterion, Δ-criterion, and λ₂-criterion are applied to Particle Image Velocimetry data gathered fore and aft of the last row centerline turbine. Q-criterion and λ₂-criterion provide a clear indication of regions where vortical activity exists while the Δ-criterion does not. Galilean decomposition, Reynolds decomposition, vorticity, and swirling strength are used to further understand the location and behavior of the vortices. The techniques identify and display the high magnitude vortices in high shear zones resulting from the …

Global Time-Independent Agent-Based Simulation For Transactive Energy System Dispatch And Schedule Forecasting, Shawn Aaron Chandler

Dissertations and Theses

Electricity service providers (ESP) worldwide have increased their interest in the use of electrical distribution, transmission, generation, storage, and responsive load resources as integrated systems. Referred to commonly as "smart grid," their interest is driven by widespread goals to improve the operations, management and control of large-scale power systems. In this thesis I provide research into a novel agent-based simulation (ABS) approach for exploring smart grid system (SGS) dispatch, schedule forecasting and resource coordination. I model an electrical grid and its assets as an adaptive ABS, assigning an agent construct to every SGS resource including demand response, energy storage, and …

Microgrid Optimal Scheduling Considering Impact Of High Penetration Wind Generation, Abdulaziz Furreh Alanazi

Electronic Theses and Dissertations

The objective of this thesis is to study the impact of high penetration wind energy in economic and reliable operation of microgrids. Wind power is variable, i.e., constantly changing, and nondispatchable, i.e., cannot be controlled by the microgrid controller. Thus an accurate forecasting of wind power is an essential task in order to study its impacts in microgrid operation. Two commonly used forecasting methods including Autoregressive Integrated Moving Average (ARIMA) and Artificial Neural Network (ANN) have been used in this thesis to improve the wind power forecasting. The forecasting error is calculated using a Mean Absolute Percentage Error (MAPE) and …

Solar And Conservative Energy, Md Zahidur Rahman, Jonathan Anspike

Publications and Research

In the solar power and conservative energy, our basic mission was to build things that don’t use any sort of fuel that harms the environment. One of the most well-liked ways of conserving energy is using solar panels. Solar panels capture light, and transforms that light into electrical. The first objective in this research was to build an electric car that uses solar panels. To do so we connected a solar panel to a motor which rotates a series of gears that turns the wheels. We used a lot of sunlight though to power the motor enough were the gears …

A Clustering Approach To Domestic Electricity Load Profile Characterisation Using Smart Metering Data, Fintan Mcloughlin, Aidan Duffy, Michael Conlon

Articles

The availability of increasing amounts of data to electricity utilities through the implementation of domestic smart metering campaigns has meant that traditional ways of analysing meter reading information such as descriptive statistics has become increasingly difficult. Key characteristic information to the data is often lost, particularly when averaging or aggregation processes are applied. Therefore, other methods of analysing data need to be used so that this information is not lost. One such method which lends itself to analysing large amounts of information is data mining. This allows for the data to be segmented before such aggregation processes are applied. Moreover, …

Nanogrid Electrical Design And Analysis, Phillip Phung

Electrical Engineering

Power plant generators have quality protection over long-range transmission, but localized generation interacts with multiple power sources, and needs maintenance to ensure grid safety. Localized and distributed generation must solve these issues to remain viable economically and efficiently in power industries. Cal Poly’s Building 20 provides on-campus location to interconnect renewable generation with interconnection disconnect capabilities.

Cal Poly’s grid includes three localized generators flowing through the Cal Poly substation. Unlike other universities which use power from utilities across distant transmission lines, Cal Poly generates energy using onsite generators. Research including additional possible sites of power generation helps determine the effects …

A Study Of Decision Process In Mcdm Problems With Large Number Of Criteria, Jian Liu, Peng Liu, Si Feng Liu, Xian Zhong Zhou, Tao Zhang

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, an effective decision process method is proposed to address the challenge in a multiple criteria decision-making (MCDM) problem because of large number of criteria. This method is based on the criteria reduction, tolerance relation, and prospect theory (PT). By building a discernibility matrix for tolerance relation (DMTR) in an MCDM problem with numerical values or interval numbers, this method first allows us to recognize a set of critical criteria from a large criteria pool and ignore the other criteria. Next, it establishes the criteria weights through the DMTR as they are usually not indicated in the data. …

Hybrid Electric Power System Validation Through Parameter Optimization, Hasnaa Khalifi

Doctoral Dissertations and Master's Theses

Battery models can be developed from first principles or from empirical methods. The work presented in this thesis is semi-empirical, the model was validated using test data through parameter optimization. Simulink Parameter Estimation toolbox was used to identify the battery parameters and validate the battery model with test data. Experimental data was obtained by discharging the battery of a modified 2013 Chevrolet Malibu hybrid electric vehicle. The resulting battery model provided accurate simulation results over the validation data. For the constant current discharge, the mean squared error between measured and simulated data was 0.26 volts for the terminal voltage and …

Three-Phase Generation Using Reactive Networks, Tattiana Karina Coleman Davenport

Master's Theses

Household appliances utilize single-phase motors to perform everyday jobs whether it is to run a fan in an air conditioner or the compressor in a refrigerator. With the movement of the world going “green” and trying to make everything more efficient, it is a logical step to start with the items that we use every day. This can be done by replacing single-phase motors with three-phase motors in household appliances. Three-phase motors are 14% more efficient than single-phase motors when running at full load and typically cost less over a large range of sizes [1]. One major downside of incorporating …

Electrochemical Monitoring Of Cell Wall-Regulated Transient Extracellular Oxidative Burst From Single Plant Cells, Jun-Tao Liu, Yan-Ling Liu, Zhi Cheng, Shi-Jing Chen, Wei-Hua Huang

Journal of Electrochemistry

Oxidative burst by rapid, transient generation of reactive oxygen species (ROS) is a fundamental process for plant disease defense and signal transduction. ROS can be protective or toxic depending on their concentrations, and critical balance between ROS production and scavenging is regulated by complex and perfect mechanisms in plant cells. However, the process of rapid and transient ROS burst from plant cells and their regulatory mechanisms are far from being completely understood, owing to the methodological obstacles in real-time monitoring such a fast process. In this work, we showed the application of microelectrode electrochemistry with high spatiotemporal resolution to monitor …

An Enzymatic Ethanol/O2 Biofuel Cell Powered By Commercial Vodka Fuel, Yi-Ming Yan, Lan-Qun Mao

Journal of Electrochemistry

This study demonstrates the performance of a new type alcohol/O₂ biofuel cell assembled by using alcohol dehydrogenase (ADH) and bilirubin oxidase (BOD) as the biocatalysts of the bioanode and the biocathode for the bioelectrocatalytic oxidation of alcohol and reduction of oxygen, respectively. To construct the bioanode and the biocathode, single-walled carbon nanotubes (SWCNTs) were used. In the bioanode, SWCNTs were used as the supporting materials for both methylene green (MG) which was used as the electrocatalyst for the oxidation of NADH and ADH. The as-constructed MG/ADH/SWCNTs-based bioanode exhibits a good activity toward the bioelectrocatalytic oxidation of ethanol. In the …

Electrochemical Detection Of L-Cysteine Based On Iron Phthalocyanine/Nitrogen-Doped Graphene Modified Electrodes, Jing-Jing Xiao, Hui-Ying Xu, Li Xu, Bao-Hong Liu

Journal of Electrochemistry

In this study, we report a facile method to develop FePc/N-G hybrid modified electrode for the detection of L-cysteine. The electrochemical sensor was characterized by cyclic voltammetry and amperometric response. The sensor exhibited a wider linear range with rapid response which has outperformed pure FePc/GCE, highlighting the important role of nitrogen doped graphene as substrate for improving the electrochemical response property.

Nanosized Fe2O3 On Three Dimensional Hierarchical Porous Graphene-Like Matrices As High-Performance Anode Material For Lithium Ion Batteries, Qin-Wei Zhang, Yun-Yong Li, Pei-Kang Shen

Journal of Electrochemistry

Ferric oxide (Fe₂O₃) as a promising anode material for lithium ion battery is due to its high theoretical capacity (1007 mAh·g^-1), earth abundance and low cost. The nanosized Fe₂O₃ on the three dimensional hierarchical porous graphene-like network (denoted as Fe₂O₃-3D HPG) has been synthesized by homogeneous precipitation and heat treatment. The 3D HPG can provide a highly conductive structure in conjunction to support well contacted Fe₂O₃ nanoparticles, and effectively enhance the mechanical strength of the matrices during volume changes, as well as improve the …

Preparation And Properties Of Titanium Based Metal Oxide Electrodes For Ammonia Nitrogen Wastewater Treatment, Xue Li, Meng Xue, Ling Huang, Jun-Tao Li, Shi-Gang Sun

Journal of Electrochemistry

In this paper, four types of titanium based metal oxides electrodes were prepared by thermal decomposition method: Ti/SnO₂+Sb₂O₃, Ti/SnO₂+Sb₂O₃/SnO₂+IrO₂, Ti/SnO₂+Sb₂O₃/SnO₂+RuO₂, Ti/SnO₂+Sb₂O₃/SnO₂+CeO₂. The XRD results show that CeO₂ in Ti/SnO₂+Sb₂O₃/SnO₂+CeO₂ displayed a good crystal structure, and there was no significant oxygen evolution reaction occurred after electrolytic oxidation. Compared with the other three electrodes, the Ce-doped …

Naio4 Oxidation Of Mussel Adhesive Protein Film And Its Corrosion Protection For Mg-1.0ca Alloy, Rui-Qing Hou, Ping-Li Jiang, Shi-Gang Dong, Chang-Jian Lin

Journal of Electrochemistry

The effect of oxidation of mussel adhesive protein (Mefp-1) film on the corrosive resistance for Mg-1.0Ca alloy was investigated by scanning electron microscopy (SEM), atom force microscopy (AFM), electron probe microanalysis (EPMA), Infrared reflection absorption spectroscopy (IRAS) and electrochemical methods. The results showed that the NaIO₄ induced oxidation of the pre-formed Mefp-1 film with porous morphology involved structural change of the DOPA group in the protein and resulted in a more uniform film with net-like morphology. The protein film without oxidation had an increasing resistance for the corrosion of Mg-1.0Ca alloy up to 7 days exposure. After oxidation, Epit …

A Low-Cost Loop Measurement Tool For Dc-Dc Converters, Shouee B. Lin

Master's Theses

Loop measurements are very important in evaluating dynamic performance of DC-DC converters. In this thesis, a small loop measurement tool as a low-cost alternative to a network analyzer is proposed. The tool is particularly useful when a network analyzer is not always available for use, for example when engineers are working on-site with customers or when a network analyzer is not affordable due to their relatively high cost. The design, simulation, and hardware implementation of the inexpensive loop measurement tool will be presented in this thesis. Results from computer simulation and hardware prototype demonstrate the ability of the proposed tool …

Con-Resistant Trust For Improved Reliability In A Smart Grid Special Protection System, Crystal M. Shipman, Kenneth M. Hopkinson, Juan L. Lopez Jr.

Faculty Publications

This paper applies a con-resistant trust mechanism to improve the performance of a communications-based special protection system to enhance its effectiveness and resiliency. Smart grids incorporate modern information technologies to increase reliability and efficiency through better situational awareness. However, with the benefits of this new technology come the added risks associated with threats and vulnerabilities to the technology and to the critical infrastructure it supports. The research in this paper uses con-resistant trust to quickly identify malicious or malfunctioning (untrustworthy) protection system nodes to mitigate instabilities. The con-resistant trust mechanism allows protection system nodes to make trust assessments based on …

A New Design Method For Vanadium Redox Batteries In Renewable Energy Systems, Casey Gibson, Karla G. Morrissey Unversity Of Arkansas, Fayetteville

Inquiry: The University of Arkansas Undergraduate Research Journal

This study investigated the behavior of vanadium redox flow batteries (VRFBs), which are batteries capable of easily switching between charging and discharging modes, making them a suitable option for storing intermittent sources of alternative energies (solar, wind, etc). Since different sizes of the battery provide varying voltages, optimal parameters for a particular home are key for implementation. These parameters, specifically the cell and tank volumes of the battery that are capable of providing consistent on-load voltage, were determined using data from a 13 kW solar array and a medium-sized house. Charge/discharge current values were used to run a mathematical model …

Romania's Participation To The European Assessment Project Titled Hyunder, Multi-Criterial Analyses Of Salt Cavern Locations, Ioan Iordache, Dorin Schitea, Adriana Marinoiu, Mihaela Buga, Mihai Balan, Ioan Stefanescu, Adrian Gheorghe, Mihaela Iordache, Viviana Cigolotti (Ed.), Chiara Barchiesi (Ed.), Michela Chianella (Ed.)

Engineering Management & Systems Engineering Faculty Publications

The scope of the work is to assess the potential, the actors and relevant business cases for large scale storage of renewable electricity by hydrogen underground storage in Romania. This presentation intends to provide a picture of the multi-criterial analyses of salt cavern locations in Romania.

The energy sector is facing with the necessity to store large energy quantities for short to long term in order to adapt to the increasingly intermittent renewable energy. The results of this presentation have originated from an ongoing European assessment project by the name of HyUnder (FCH JU, grant 303417) regarding utilization of salt …

Lighting Design In Europe: Aligning The Demands For Lower Energy Usage With Better Quality., Kevin Kelly, James Duff

Articles

Lighting design is one of the fastest changing areas in building engineering. It has evolved significantly in recent years due to changing technology and demands for improved quality, better control, reduced energy and sustainability. This paper is an overview of what is happening in Europe and elsewhere and examines the literature to find that latest recommendations in the Code for Lighting issued by the SLL (Society of Light and Lighting) in the UK change previous demands for equal illuminance across a working plane to more specific and demanding criteria. There are recommendations for qualitative metrics and better distribution of light …

Boost Battery, Samuel Rauch, Alvin Ng, Lacy Sigman

Electrical Engineering

In modern times, the problem of a depleted battery confronts us too often. Whether it appears with a smartphone or with any other electronic device, the situation frustrates all consumers. This project designs and constructs a compact portable battery charger that charges through kinetic energy. Thus, one can perform everyday activities, such as walking or running, and charge up a backup battery with no extra effort or time. Additionally, an attachable band harvests thermal energy to maximize the amount of clean power generated. Energy harvesting from kinetic motion and thermal differences provide users with power when no actual power suppliers …

Single Phase Multilevel Inverter For Grid-Tied Photovoltaic Systems, Martin Edward Prichard

Theses and Dissertations--Electrical and Computer Engineering

Multilevel inverters offer many well-known advantages for use in high-voltage and high-power applications, but they are also well suited for low-power applications. A single phase inverter is developed in this paper to deliver power from a residential-scale system of Photovoltaic panels to the utility grid. The single-stage inverter implements a novel control technique for the reversing voltage topology to produce a stepped output waveform. This approach increases the granularity of control over the PV systems, modularizing key components of the inverter and allowing the inverter to extract the maximum power from the systems. The adaptive controller minimizes harmonic distortion in …

A Computational Study Of A Photovoltaic Compound Parabolic Concentrator, William M. Vance

Browse all Theses and Dissertations

Routines have been written and added to the Wright State developed solar system simulation program called Solar_PVHFC to model incident solar radiation for a compound parabolic concentrator (CPC) that uses solar panels (photovoltaic panels) to produce electrical energy. Solar_PVHFC is a program that models a solar energy system composed of solar panels to produce electricity from the sun, hydrogen storage tanks to chemically store the energy produced by the solar panels, and fuel cells to convert between electrical and chemical energy when required. Solar_PVHFC features several adjustable parameters to model a solar panel, hydrogen storage, and fuel cell system. Now …

Synchrophasor Assisted Efficient Fault Location Techniques In An Active Distribution Network, Anil Khanal

Dissertations

Reliability of an electrical system can be improved by an efficient fault location identification for the fast repair and remedial actions. This scenario changes when there are large penetrations of distributed generation (DG) which makes the distribution system an active distribution system. An efficient use of synchrophasors in the distribution network is studied with bidirectional power flow, harmonics and low angle difference consideration which are not prevalent in a transmission network. A synchrophasor estimation algorithm for the P class PMU is developed and applied to identify efficient fault location. A fault location technique using two ended synchronized measurement is derived …

Comparing The Efficiency Of Heterogeneous And Homogeneous Data Center Workloads, Brandon Kimmons

College of Graduate Studies: Theses & Dissertations

Abstract

Information Technology, as an industry, is growing very quickly to keep pace with increased data storage and computing needs. Data growth, if not planned or managed correctly, can have larger efficiency implications on your data center as a whole. The long term reduction in efficiency will increase costs over time and increase operational overhead. Similarly, increases in processor efficiency have led to increased system density in data centers. This can increase cost and operational overhead in your data center infrastructure.

This paper proposes the idea that balanced data center workloads are more efficient in comparison to similar levels of …