Power and Energy Commons^™

Quantum Dot Band Gap Investigations, John Ryan Peterson

Student Works

Improving solar panel efficiency has become increasingly important as the world searches for cheap renewable energy. Recent developments in the industry have focused on multi-layer cells, some of which use semiconducting dyes to absorb light in place of crystalline solids. In this paper, I characterize various dyes recently synthesized for use in solar panels. These dyes contain semiconducting nanoparticles enclosed primarily by the protein ferritin to limit particle size. The band gaps were measured using either optical absorption spectroscopy or measuring the photoluminescence spectrum, depending on the type of semiconductor. The results indicate that both manganese oxide and lead sulfide …

"Feasibility Of Efficient Photovoltaics In Eastern Kentucky" / "Developing A 3-D Printed Solar Vehicle With Computational Fluid Dynamics (Cfd) Simulator", Adam N. Stanley, Matthew R. Hezseltine

Posters-at-the-Capitol

Abstract 1

Feasibility of Efficient Photovoltaics in Eastern Kentucky

Photovoltaics (PV-also called solar photovoltaic devices) are used to harness the power of the sun via the electronic process that occurs within semiconductor cells. The solar energy is absorbed by the cells, which causes the electrons to break away from their atoms, allowing them to flow within the material to produce electricity. This electricity will become the renewable energy for Kentucky, as the generation of coal will but come to a stop within the near future. Like Denmark who is running on 100% renewable generation we must stride to become fully …

Modeling Of A Multi-Megawatt Grid Connected Pv System With Integrated Batteries, Vandana Rallabandi, Oluwaseun M. Akeyo, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The multi-megawatt grid connected photovoltaic (PV) system studied in the paper includes parallel arrays and power electronic units, each with their own DC-DC and DC-AC converters. In one configuration, the DC-AC converters of adjacent parallel sections are connected in cascade, in order to effectively operate as a multilevel inverter, thereby reducing the filtering requirements. Grid voltage oriented control is employed for inverters and a battery is incorporated for energy storage and performance improvement. Modeling is performed with the PSCAD/EMTDC software, such that both the power electronics components, controls and subsystem aspects, and the electric grid power system issues, can be …

Benchmarking Approach For Empirical Comparison Of Pricing Models In Drms, Seif Azghandi, Kenneth M. Hopkinson, Kennard R. Laviers

Faculty Publications

emand response management systems often involve the use of pricing schemes to motivate the efficient use of electrical power. Achieving this efficiency requires the detection of electrical power patterns. The detection of these patterns normally involves use of non-linear, quasi-non-linear, and at times linear data pattern detection models. The behavioural disparities of these models and specifically when used for a specific set of data make it hard to select the most efficient model. The contribution of this study is devising an empirical benchmark (reference) ( perfect ) control pricing (PCP) model through which various models are compared in order to …

Micro/Nano-Structured Electrode Materials For Sodium-Ion Batteries, Shuang Yuan, Yun-Hai Zhu, Sai Wang, Tao Sun, Xin-Bo Zhang, Qiang Wang

Journal of Electrochemistry

Sodium has similar physics and chemical properties to lithium, alternatively, sodium (Na)-ion batteries have again aroused a great deal of interest recently, particularly for large-scale stationary energy storage applications due to the practically infinite sodium resources and low cost. However, the technics and materials for Na-ion batteries are immature. Therefore, development of advanced anode and cathode materials for Na-ion batteries is urgently desired but remains a great challenge. This paper briefly reviews some recent progresses in this field, addressing the morphology effects, as well as functions of carbon composite materials toward Na-ion batteries. Several electrode materials with micro/nano-structures based on …

Research Progress In Cycle Stability Of Silicon Based Li-Ion Battery Anodes, Ze-Liang Guo, Hui Wu

Journal of Electrochemistry

Silicon(Si), with the highest specific capacity currently known, is a promising anode material for Li-ion battery. However, in the charging and discharging process, with Li atoms inserting into and breaking out of the Si crystal lattices, the Si anode undergoes enormous volume expansion and contraction, ending in pulverization. The fact that the specific capacity of bulk Si anodes drop quickly is a challenging problem. In this review, we summarize recent progresses in Si anode. We concern about the nanostructure of silicon, cooperation of silicon with other additives and macrostructure design of anodes. We discuss strengths and shortcomings of different methods, …

Electrochemical Performance Of Crystalline Li12Si7 As Anode Material For Lithium Ion Battery, Ya-Xiong Yang, Rui-Jun Ma, Ming-Xia Gao, Hong-Ge Pan, Yong-Feng Liu

Journal of Electrochemistry

Crystalline Li₁₂Si₇ is successfully synthesized by heating the mixture of LiH and Si with a molar ratio of 12:7, which avoids the huge difference of the melting points between Li and Si. The electrochemical performance and lithium storage mechanism of the as-prepared Li12Si7 are studied in this work. It is found that only a change in cell volume takes place without a phase change during the lithiation/delithiation of Li₁₂Si₇ at a voltage range of 0.02 ~ 0.6 V, exhibiting a solid-solution lithium storage mechanism. Such a lithium storage process effectively retards the volume effect …

Continuous Synthesis And Condition Exploration Of Precursor Ni1/3Co1/3Mn1/3(Oh)2 Ternary Cathode Material, Zhi-Jun Jiang, Ya-Li Zhang, Qian Wang, Hui Zhang

Journal of Electrochemistry

Commercial LiNi_1/3Co_1/3Mn_1/3(OH)₂ ternary material is generally prepared by a combination of co-precipitation and solid state reaction method. The particle size distribution and morphology of Ni_1/3Co_1/3Mn_1/3(OH)₂ precursor have a great impact on the electrochemical performance of LiNi_1/3Co_1/3Mn_1/3O₂. In this work, the precursor Ni_1/3Co_1/3Mn_1/3(OH)₂ ternary cathode material was prepared by co-precipitation method with MnSO₄, NiSO₄, and CoSO₄ as raw materials, NaOH as a precipitating agent and NH_{3 …}

Research And Application Of Key Materials For Sodium-Ion Batteries, Yong-Chang Liu, Cheng-Cheng Chen, Ning Zhang, Liu-Bin Wang, Xing-De Xiang, Jun Chen

Journal of Electrochemistry

Sodium-ion batteries (SIBs) have been considered as a potential large-scale energy storage technology owing to the abundance, wide distribution, and low price of sodium resources. However, the larger and heavier sodium ion as compared to lithium ion makes it difficult to identify appropriate electrode materials with the capability for fast and stable sodium-ion insertion/extraction. Furthermore, the optimization of electrolyte, the matching of cathode and anode materials, and the construction of sodium-ion full batteries with high-performance, high-safety, and low-cost are urgently needed in order to make SIBs commercially available. This review summarizes the up-to-date research progresses in key materials (including cathode, …

Advances And Prospects Of Lithium-Sulfur Batteries, Shou-Yi Yuan, Ying Pang, Li-Na Wang, Yong-Gang Wang, Yong-Yao Xia

Journal of Electrochemistry

Lithium-sulfur batteries have recently attracted worldwide attention due to the high specific theoretical energy density of sulfur cathode (2600 Wh⋅kg^-1), low cost and wide availability of sulfur. However, the practical application of lithium-sulfur batteries has been hindered by several challenges, such as the shuttling of polysulfide intermediates, the large volume expansion of sulfur during charge/discharge and the dendrites formation on lithium anode. Foremost among these is the shuttling effect arising from the dissolution of lithium polysulfides intermediate into the electrolyte from the cathode reaction and their diffusion to the anode where they react with metal lithium to form …

Research Progress Of Si-Based Anode Materials For Lithium-Ion Batteries, Ding-Qiong Chen, Yang Yang, Qiu-Li Li, Jin-Bao Zhao

Journal of Electrochemistry

Owing to its high theoretical specific capacity (4200 mAh·g^-1), silicon is a promising candidate to replace graphite as the anode in lithium ion batteries (LIBs). However, low intrinsic electric conductivity and dramatic volume change (~ 300%) during the process of lithiation and delithiation result in electrode pulverization and capacity loss with cycling, accordingly, the application of silicon as an anode in LIBs has been severely hindered. We will discuss the structure of silicon electrode including synthesis of Si-based composites,the selection of binder for silicon and the fabrication of binder-free Si-based electrode, as well as the electrolyte additive to …

Template-Assisted Hydrothermal Synthesis Of Nio@Co3O4 Hollow Spheres With Hierarchical Porous Surfaces For Supercapacitor Applications, Wen Zhou, Xue-Feng Lu, Ming-Mei Wu, Gao-Ren Li

Journal of Electrochemistry

Hollow structures have shown great potentials in a variety of important applications, such as energy conversion and storage. In order to further enhance the performance, the rational design of hollow structures with higher complexity in terms of composition and structure is highly desirable and still remains a great challenge. In this work, an efficient strategy was established for the fabrication of novel NiO@Co₃O₄ hollow spheres (HSs) with hierarchical porous surfaces by silica spheres template-assisted hydrothermal synthesis. The as-fabricated NiO@Co₃O₄ HSs showed high specific surface area of 219.68 m²·g^-1, and significant …

Effects Of Lithium Salts On The Properties Of Hyperbrandched/Comb-Like Composite Polymer Electrolytes, Xian-Lei Hu, Xiao-Xu Liang, Ming-Qiu Zhang, Ruo-Xin Zhang, Li-Ping Zhang, Wen-Hong Ruan

Journal of Electrochemistry

Based on the chemical characteristics of the hydroxyl group of PVA side-chain, the hyperbrandched poly(amine-ester) (HBPAE) was used to hypergraftingly pretreated nano-silica (SiO₂) and polyving akohol (PVA). And different lithium salts were added to fabricate the SiO₂-g-HBPAE/PVA-g-HBPAE hyperbrandched/comb-like composite polymer electrolytes (CPEs). The dispersion of nanoparticles in matrix was observed by SEM. The effects of different lithium salts on the properties of CPEs were studied by DSC, tensile test and dielectric spectra. The results showed that the hypergrafting method improved the interphase compatibility between SiO₂ and matrix. Sulfonic acid type lithium salts accelerated self-plasticizing with …

The Study Of Dynamical Electrochemical Impedance Spectroscopy For Oxygen Reduction Reaction On Pt/C Catalyst, Kun-Ming Shi, Jian-Wei Guo, Jia Wang

Journal of Electrochemistry

With joint techniques of rotating disc electrode(RDE) and electrochemical impedance spectroscopy(EIS), and further establishment on equivalent circuit model, this paper studied oxygen reduction reaction(ORR) on commercial Pt/C catalyst in acid medium. Our results found that the dynamical interface on Pt/C consists of two independent processes: 1) the PtO reduction from Pt surface, 2) the new PtO formation from ORR, thus providing key clues for catalyst stability and activity. This also implied that the dynamical interface facilitates reconstruction for porous electrode, and matches with mass transfer. One important issue is discovered that at high overpotential, the high reaction rate for ORR …

Design And Implementation Of Ccny Dc Microgrid Testbed, Mahmoud Saleh, Yusef Esa, Yassine Mhandi, Werner Brandauer, Ahmed Mohamed

Publications and Research

This paper presents the design, control, energy management, and implementation of the City College of New York (CCNY) direct current (DC) microgrid laboratory testbed. This facility was custom designed and implemented by researchers at CCNY with minimal off-the-shelf components to enable significant flexibility and reconfiguration capability. The microgrid consists of renewable energy resources, energy storage system and controllable loads, and can operate in either a grid-connected or an islanded mode. The design steps, requirements, and results of the developed testbed were discussed. Moreover, several operational scenarios were tested. The experimental results verify the applicability and flexibility of the developed microgrid …

Plasticized Polymer Coatings For Sh-Saw Sensors For High Sensitivity And Long-Term Monitoring Of Btex Analytes In Liquid Phase, Pintu Adhikari

Master's Theses (2009 -)

BTEX compounds (benzene, toluene, ethylbenzene, and xylene) are constituents of crude oil and hazardous to human health. Among them, benzene has the lowest maximum contaminant level for drinking water because of its carcinogenicity. Spills or leakage from underground storage tanks or hazardous waste sites can contaminate nearby groundwater with these volatile organic compounds. Therefore, it is very important to detect the presence of BTEX contamination as early as possible in order to start the remediation process and maintain a healthy environment. To develop an in-situ continuous monitoring sensor system, shear horizontal surface acoustic wave (SH-SAW) sensor devices are being investigated …

Configuring The Urban Smart Grid: Transitions, Experimentation, And Governance, Anthony Michael Levenda

Dissertations and Theses

In the face of challenges of energy security, decarbonization, resilience, and the replacement of aging infrastructure systems, federal, state, and local actors are facilitating the development of smart electricity networks to transition towards a more sustainable electricity system. In the United States, development of "smart grids" is being pursued as a national policy mandate and goal, promising that the deployment of smart grid technologies -- referring in general to digital information and communication technologies that sense, monitor, control and manage the electric grid -- will make electricity systems more environmentally sustainable and reliable, and at the same time, provide opportunities …

Energy Managment Of Photovoltaic Charging Station (Pv-Cs) For Green University Campus Transportation, Ayda Esfandyari, Brian Norton, Michael Conlon, Sarah Mccormack

Conference Papers

Battery Electric Vehicles (BEVs) have been recognised as the ideal solution for lowering the CO₂ emissions in the transport sector and helping to achieve a sustainable future. When BEV technology is leveraged with a solar energy source such as a Photovoltaic Charging Station (PV-CS), the CO₂ saving potential is extended to both generation and consumption points. Due to the intermittent nature of our solar resource, once the PV-CS is combined with a storage unit, energy production is achieved without risking the disruption to power supply reliability and quality. Technological University Dublin (DIT) has recognised the viability of this …

Technological Assessment Of Different Solar-Biomass Systems For Hybrid Power Generation In Europe, C. M. Iftekhar Hussain, Brian Norton, Aidan Duffy

Articles

Solar Tower thermal (ST), Parabolic Trough thermal (PT), Linear Fresnel thermal (LF) and Solar PV are discussed in the context of suitability for hybridization with biomass in Europe. Technical, economical and climate data have been compared to identify the key drivers of technology selection in setting up large scale solar-biomass hybrid power plants. The sole solar-biomass hybrid power plant is currently in operation in Spain uses PT technology due to its performance characteristics, comparatively easy installation process compared to ST and relatively higher heat and optical gain than LF. The climate condition in the EU shows that the region within …

On The Feasibility Of Carbon Nanotube Windings For Electrical Machines — Case Study For A Coreless Axial Flux Motor, Vandana Rallabandi, Narges Taran, Dan M. Ionel, John F. Eastham

Power and Energy Institute of Kentucky Faculty Publications

The latest developments in carbon nanotube (CNT) wires and yarns attract great interest for potential application to electromagnetic devices, such as electrical machines and transformers. The CNT material properties are largely different from copper and aluminum in terms of electrical conductivity, mass density, and thermal transfer, creating a new design paradigm for which the traditional rules and device topologies no longer apply. This paper proposes a brushless permanent magnet multidisc axial flux construction with coreless stator and special windings and minimal rotor back iron, as a suitable topology for CNT winding application. Specific analytical closed-form sizing equations, as a function …

Capture And Recycle Of Industrial Co2 Emissions Using Mircoalgae, Michael H. Wilson, Daniel T. Mohler, John G. Groppo, Thomas E. Grubbs, Stephanie Kesner, E. Molly Frazar, Aubrey Shea, Czarena L. Crofcheck, Mark Crocker

Center for Applied Energy Research Faculty and Staff Publications

A novel cyclic flow photobioreactor (PBR) for the capture and recycle of CO₂ using microalgae was designed and deployed at a coal-fired power plant (Duke Energy’s East Bend Station). The PBR was operated continuously during the period May–September 2015, during which algae productivity of typically 0.1–0.2 g/(L day) was obtained. Maximum CO₂ capture efficiency was achieved during peak sunlight hours, the largest recorded CO₂ emission reduction corresponding to a value of 81 % (using a sparge time of 5 s/min). On average, CO₂ capture efficiency during daylight hours was 44 %. The PBR at East Bend …

Application Of Metal-Organic Frameworks In Dye-Sensitized Solar Cells, Ya-Feng Li, Qing-Qing Sun, Ming-Deng Wei

Journal of Electrochemistry

To assemble dye-sensitized solar cells (DSSCs) with high efficiencies, their photoanodes should have large specific surface area to establish a large adsorption amount of dyes and good light-harvesting ability. From this point of view, it will be an interesting topic to explore the application of metal-organic frameworks (MOFs) in the field of DSSCs due to their huge specific surface area. This paper introduces the application of MOFs in photovoltaic devices briefly, and then summaries our approaches in using MOFs in the study of DSSCs, including the pre-treatment and the post-treatment of photoanode, the preparation of photoanode materials and the light …

Prospects Of D-Π-A Structured Porphyrins And Their Photoelectrochemical Application, Shuang-Shuang Liu, Jian-Feng Lu, Ming-Kui Wang

Journal of Electrochemistry

Porphyrins and their metalloderivatives are a class of compounds exhibiting a wide variety of interesting and highly useful properties, such as chlorophyll. Porphyrins are particularly interesting in photoelectrochemical applications due to their structural similarity to chlorophylls in natural photosynthetic systems, as well as their strong and tunable absorption properties. Recently, various porphyrins have been extensively studied for their applications in solar cells, photocatalytic hydrogen production, optical information storage and others. This review will focus on the unique physical and chemical properties of D-π-A structured porphyrins, and their photovoltaic performances in dye-sensitized solar cells. A brief discussion in the future development …

Activation Effect Of Nano-Carbon Derived From Co2 On Lead Electrode In Sulfuric Aqueous Solution, Yu-Qiao Song, Hua Zhu, Guang-Jin Zhao, Wen-Long Wu, Shou-Bin Zhou, Di-Hua Wang

Journal of Electrochemistry

Serious sulfation of the negative plate is one of the most popular reasons of the early failure of lead-acid battery. Addition of nano-carbon was proved to be effective for recovering the sulfated electrode and the property of the carbon material always plays an important role. In this work, a new kind of nano-carbon material with high electrical conductivity and good adsorption capability for heavy metal cations, which is electrochemically prepared from CO₂ in molten carbonates, was tested as activation additive for the sulfated lead electrode by cyclic voltammetry and SEM measurements. The results showed that the as-prepared carbon can …

Hydrothermal One-Step Synthesis Of Layered Nickel/Cobalt Double Hydroxide With Using Shape-Directing Agent And Homogeneous Precipitating Agent, Li-Wei Zhu, Yun-Hai Yan, Hui Jia, Run-Fen Liang

Journal of Electrochemistry

Nickel/cobalt double hydroxide (Ni/Co-DH) has been prepared by facile hydrothermal one-step synthesis method using hexamethylene tetramine (HMT) as a homogeneous precipitating agent and cetyltrimethylammonium bromide (CTAB) as a shape-directing agent. With the hydrolysis of HMT and the use of CTAB, the Ni/Co-DH could be synthesized without additional alkali source, and in the meantime, the Ni/Co-DH exhibited a controlled mesopore size of 13.4 nm and a large BET surface area of 93.6 m² •g^-1 . The X-ray diffraction (XRD) pattern displays that the Ni/Co-DH existed as a mixture of α-Ni(OH)₂-β-Co(OH)₂. The scanning electron microscope (SEM) …

Special Issue: Photoelectrochemistry And New Types Of Solar Cells, Chang-Jian Lin, Yong-Fang Li

Journal of Electrochemistry

/

Cathode Buffer Layer For Improving Photovoltaic Performance Of Planar P-I-N Perovskite Solar Cells, Xiao-Dong Liu, Yong-Fang Li

Journal of Electrochemistry

Organic/inorganic hybrid metal halide perovskite semiconductor materials have drawn great attention for the application in solar cells in recent years because of their combined superior photoelectrical properties of inorganic semiconductors (with high dielectric constant and high charge carriers mobility) and organic semiconductors (with good solution processability and high absorbance). The power conversion efficiency (PCE) of the organometal halide perovskite solar cells (pero-SCs) based on CH₃NH₃PbI₃ has been increased dramatically in a few years from 3.8% to a certified 22.1%, primarily owing to the development of new interfacial materials, careful optimization of morphology, and perovskite crystallization …

Theoretical Study Of Photoelectrochemical Reactions And Ec-Sers On Spr Metallic Electrodes Of Silver And Gold, Yuan-Fei Wu, Ran Pang, Meng Zhang, Jian-Zhang Zhou, Bin Ren, Zhong-Qun Tian, De-Yin Wu

Journal of Electrochemistry

At present photoelectrochemistry has received much concern back to nanostructures of noble metals from semiconductor electrodes. This is due to the surface plasmon resonance (SPR) effect of metallic nanostructures, which can effectively convert the far-field light to the near-field light and concentrate the photonic energy to the local surface area with high energy density. Thus, the different enhancement mechanisms, such as the local optical field enhancement, the formation of light generated hot carriers (hot electron-hole pairs), or the photothermal effect, have been proposed in literatures. On the basis of the SPR enhancement effect, the surface-enhanced Raman spectroscopy (SERS) can be …

Photoelectrochemical Water Splitting Cells: Methods For Improving Performance Of Electrodes And Recent Progress On Photocathodes, Kai-Jian Zhu, Wen-Jun Luo, Zhong-Jie Guan, Xin Wen, Zhi-Gang Zou, Wei Huang

Journal of Electrochemistry

Photoelectrochemical water splitting can convert solar energy into hydrogen which is an ideal way to utilize and store solar energy. A p-n tandem cell is considered as the most promising solar water splitting cell due to its high theory conversion efficiency, low cost and photoelectrode material flexibility. However, solar conversion efficiency of a tandem cell is still low in the experiment because of poor performance in a single photoelectrode. In this review, we have introduced some effective approaches to improve the performances of photoelectrodes by reducing recombination of photogenerated carriers in the bulk or on the surface, and suppressing back …

Preparations And Photoelectrochemical Properties Of Phosphate Modified Rgo-Biobr Nanocomposites, Shuang-Ying Chen, Zhi-Jun Li, Xu-Liang Zhang, Kang Hu, Rui Yan, Li-Qiang Jing

Journal of Electrochemistry

The RGO-BiOBr nanocomposites have been successfully synthesized by a hydrothermal process, and then modified with phosphorous acids. The photoelectrochemical properties of the fabricated RGO-BiOBr nanocomposite films were studied. The results indicate that the photocurrent densities of RGO-BiOBr were much larger compared with those of the bare BiOBr, and interestingly, the photocurrent densities were further improved after phosphate modification. Based on the analyses of the produced hydroxyl radical amounts, the enhanced photocurrent densities could be attributed to the introduction of RGO and to the formed negative fields of modified phosphate groups, which are favorable for electrons to be transferred and for …