Power and Energy Commons^™

Designing A Solar Pv System To Power A Single-Phase Distribution System, Ana Guerra Vega

Electrical Engineering Undergraduate Honors Theses

Over the last decade, the costs of PV system components have dropped more than 70%. Additionally, green energy incentives like the 30% tax credit have been pushed forward. PV solar systems have become accessible to the general public. Companies are pledging to reduce their carbon emissions.

As part of their green initiative, the City of Fayetteville has requested a feasibility study for a PV system to be installed on the rooftop of the Facilities Management building, 115 S. Church Ave, Fayetteville, AR, 72701. This thesis shows the design process of this PV system and the return on investment estimation. While …

Manufacturing And Testing The Permanent Magnet Linear Motor, Renjie Kang

Senior Theses

Controlled mechanical motion is vital in many useful applications in technology. Among them, linear motors have advantages over traditional rotating motors. In this work, we built a permanent magnet linear motor to test and measure its energy efficiency. A maximum 29% total energy efficiency, and 67% energy transfer rate, were detected. In addition, a C-shape support structure was added to the moving part in order to increase the moving accuracy. The tests show that, with the support structure, the fluctuation in the vertical direction decreases significantly, but the friction of the system slightly increases.

Design Optimization Of Electric Machines With 3d Fea And A New Hybrid Doe-De Numerical Algorithm, Narges Taran, Vandana Rallabandi, Dan M. Ionel, Greg Heins, Dean Patterson, Ping Zhou

Power and Energy Institute of Kentucky Faculty Publications

This paper discusses the multi-objective optimization of axial flux permanent magnet (AFPM) machines with ferrite spoke-type magnets, utilizing 3D finite element models. Three-dimensional finite element analysis is computationally expensive, and furthermore, substantial computation time is expended by optimization algorithms in evaluating low performing designs whose performance is far from the optimum if the search space is not specified correctly. In this regard, this work proposes two new methods for identifying the search space. The search is limited to ranges of input geometric variables where high performing designs are likely to be found. The optimization algorithm utilized is based on surrogate …

Inductance Testing For Ipm Synchronous Machines According To The New Ieee Std 1812 And Typical Laboratory Practices, Vandana Rallabandi, Narges Taran, Dan M. Ionel, Ping Zhou

Power and Energy Institute of Kentucky Faculty Publications

Equivalent circuit parameters serve as the basis for performance estimation and implementation of power electronic drives controls and therefore their accurate evaluation is very important. Specified in the newly approved IEEE Std 1812, a short-circuit test can be employed, in combination with an open-circuit measurement, in order to determine the back emf and the synchronous inductance. In the case of interior permanent magnet (IPM) machines, this approach can be used only to determine the d-axis inductance and additional and separate measurements are required for the q-axis inductance. In this respect, various methods, inclusive of dc step response tests, on-load tests, …

A Comparative Study Of Methods For Calculating Ac Winding Losses In Permanent Magnet Machines, Narges Taran, Vandana Rallabandi, Dan M. Ionel, Greg Heins, Dean Patterson

Power and Energy Institute of Kentucky Faculty Publications

In this study different methods of estimating the additional ac winding loss due to eddy currents at open-circuit are explored. A comparative study of 2D and 3D FEA, and hybrid numerical and analytical methods is performed in order to recommend feasible approaches to be employed. Axial flux permanent magnet (AFPM) machine case studies are included, namely a machine with open slots and a coreless configuration. These machine topologies are expected to present a substantial amount of ac winding loss, which would therefore need to be considered during optimal design. This study is one of the first ones to compare meticulous …

Usb-C Power Adapter For Dc House Project, Tyler G. Starr, Ezzeddeen Gazali

Electrical Engineering

Despite the importance of electricity and the impact it has on our daily lives, many people around the world still live without this essential utility today. According to the International Energy Agency (IEA), approximately 1.1 billion people in the world did not have access to electricity in 2017. The DC House Project at Cal Poly aims to provide electricity to people living in rural areas by directly utilizing DC energy generated from renewable or human powered sources without the need for DC-AC conversions. However, one significant issue is the lack of a standardized DC wall socket. Standards for AC wall …

H2 Control For Improved Stability Of Multi-Area Electric Power System With High Levels Of Inverter-Based Generation, Muthanna Abdulkareem Al-Sarray

Graduate Theses and Dissertations

Increased generation capacity from non-dispatchable energy resources such as wind and solar has created challenges to ensuring the reliable delivery of electric power. This research develops a systematic three-step method of assessing the reliability of electric power systems under a variety of different possible fault conditions to ensure that overall system stability is preserved in a manner the meets regulatory requirements. The first step is a risk-based reliability method (RBRM) that accounts for the probability of a line outage versus the severity of impact. This allows system planners to judiciously allocate expenses for reliability improvements based on the greatest economic …

A Silicon Germanium Cmos Linear Voltage Regulator For Wireless Agricultural Applications, Aminta Naidili Castillo Robles

Graduate Theses and Dissertations

This thesis presents the design, simulation and test results of a silicon germanium (SiGe) complementary metal-oxide-semiconductor (CMOS) linear regulator. The objective of the circuit is to power other analog devices regardless of the load current and input voltage changes. The application of this regulator is to be part of a project developing a miniaturized semiconductor platform that can be inserted into stems of crops in order to measure data inside the plant and then send it wirelessly to the user. The linear regulator was designed on a BiCMOS SiGe 0.13µm which is a GlobalFoundries process. It has been tested at …

Local And Central Controllers For Microgrids, Edgar Ariel Escala Calame

Graduate Theses and Dissertations

The main objective of this thesis is to serve as a guide, so readers are able to learn about microgrids and to design simple controllers for different AC microgrid applications. In addition, this thesis has the objective to provide examples of simulation cases for the hierarchical structure of a basic AC microgrid which can be used as a foundation to build upon, and achieve more complex microgrid structures as well as more sophisticated power-converter control techniques.

To achieve these objectives, the modeling of voltage source converters and control design in the z-domain are presented. Moreover, the implementation and transient analysis …

Model Development And Assessment Of The Gate Network In A High-Performance Sic Power Module, William Austin Curbow

Graduate Theses and Dissertations

The main objective of this effort is to determine points of weakness in the gate network of a high-performance SiC power module and to offer remedies to these issues to increase the overall performance, robustness, and reliability of the technology. In order to accomplish this goal, a highly accurate model of the gate network is developed through three methods of parameter extraction: calculation, simulation, and measurement. A SPICE model of the gate network is developed to analyze four electrical issues in a high-speed, SiC-based power module including the necessary internal gate resistance for damping under-voltage and over-voltage transients, the disparity …

Synchrophasor-Based Fault Location Detection And Classification, In Power Systems, Using Artificial Intelligence, Hemal Falak

Graduate Theses and Dissertations

With the introduction of sophisticated electronic gadgets which cannot sustain interruption in the provision of electricity, the need to supply uninterrupted and reliable power supply, to the consumers, has become a crucial factor in the present-day world. Therefore, it is customary to correctly identify fault locations in an electrical power network, in order to rectify faults and restore power supply in the minimum possible time. Many automated fault location detection algorithms have been proposed, however, prior art requires topological and physical information of the electrical power network. This thesis presents a new method of detecting fault locations, in transmission as …

Real-Time Fault Detection And Reconfiguration Of A Three-Phase Electric Motor Drive, Danyal Mohammadi

Boise State University Theses and Dissertations

Variable-frequency drives (VFDs) are widely used for control of electrical machines such as induction motors (IMs) or permanent-magnet synchronous motors (PMSMs). Similar to other electrical devices, these drives are subject to failure. Several types of faults are associated with VFDs. For instance, faults such as an open-switch fault, a short-circuit switch fault are the two common faults in VFDs. These faults can yield catastrophic consequences if proper remedial action is not taken.

A unique remedial topology for the post-fault period and a new pulse width modulation (PWM) strategy are proposed so that not only the motor drive can continue the …

In Situ/Operando Visualization Of Electrode Processes In Lithium-Sulfur Batteries: A Review, Shuang-Yan Lang, Xin-Cheng Hu, Rui Wen, Li-Jun Wan

Journal of Electrochemistry

Lithium-sulfur (Li-S) batteries have been regarded as one of the most promising candidates for the next-generation energy storage devices. Fundamental understanding of the structure and evolution processes at electrode-electrolyte interfaces is essential to the further development. In this review, we summarize recent advances in the interfacial observations by means of various in situ/operando visualization techniques, including scanning probe microscopy (SPM), electron microscopy (EM), X-ray microscopy (XRM) and optical microscopy (OM). The real-time investigation provides important evidence for the morphology and component changes including S/Li₂S transformation, polysulfide dissolution on cathodes and Li/solid electrolyte interphase (SEI) evolution on anodes, which …

Sensitive Photoelectrochemical Assay Of Nucleic Acids Based On Catalytic Hairpin Assembly And Ru(Nh3)63+, Ya-Min Fu, Xiao-Xia Yan, Xiao-Hua Zhang, Jin-Hua Chen

Journal of Electrochemistry

A simple “signal-on” photoelectrochemical (PEC) sensing platform for sensitive assay of nucleic acids was developed by coupling catalytic hairpin assembly (CHA) signal amplification strategy with Ru(NH₃)₆³⁺. Herein, cadmium sulfide (CdS) was deposited on the TiO₂/indium tin oxide (ITO) electrode by a method of successive ionic layer adsorption and reaction (SILAR), serving as one kind of photoelectric material to broaden absorption range of TiO₂ and to improve the photoelectric conversion efficiency. Thereafter, the capture DNA (C-DNA) was immobilized on the CdS/TiO₂/ITO electrode. Simultaneously, Au-hairpin DNA probe 1 (Au-HP1) and hairpin DNA …

Preparation And Electrocatalytic Oxygen Reduction Performance Of Self-Doped Sludge-Derived Carbon, Ya-Li Ye, Wei-Ming Feng, Ge Li, Zhen-Chao Lei, Chun-Hua Feng

Journal of Electrochemistry

The development of low-cost, high-performance cathode catalysts is critical for practical application of fuel cells. Here, the N, P-doped porous graphene-like carbon with outstanding oxygen reduction reaction (ORR) performance was synthesized by pyrolysis of surplus sludge, which functioned as a self-doped, self-activated, and self-templated precursor by acclimation with continuous feedings of phenol. The results show that the amounts of microorganisms were enriched after acclimation, with increasing contents of N, P, Fe, as well as C atoms. The increasing pyrolysis temperature resulted in the formation of an ordered graphitic structure, however, the excessively high temperature induced the drop in the amounts …

The Detection And Prevention Of Cascading Failure In Power Systems: A Real-Time Solution For Intentional Controlled Islanding, Faycal Znidi

Theses and Dissertations

Intentional controlled islanding (ICI), also referred as controlled system separation or system splitting, has been proposed as an effective corrective control action to help detect, prevent and mitigate the risk and spread of the cascading failures. A practical controlled islanding separation scheme needs to address two critical problems: where to island i.e., the splitting points to form sustainable islands and when to island i.e., Islanding time. This dissertation examines the causes and mechanism of power system cascading outages and develops new approaches to help detect, prevent and mitigate the risk and spread of these cascading failures. Four effective solutions: weighted …

Feasibility Study Of Direct Application Of Two Deep And Dry Geothermal Wells For Heating The Buildings Of Moeil Village, Razieh Pourdarbani, Massomeh Alibaba, Mohsen Taghaddosi

Emirates Journal for Engineering Research

No abstract provided.

An Optimization Approach Based On The Interior-Point Methodology For The Tertiary Control Of Modernized Microgrids, Isaiah D. Woodruff

Honors College Theses

With the rise in popularity of the modernized microgrids (MMGs), the addition of a controller to maximize economic efficiency while considering environmental impact is crucial. Tertiary control is at the highest control level, considering economic concerns related to the optimal operation of the microgrid and using a sampling time from minutes to hours; tertiary controls manage the flow of power between the microgrid and the connected grid. In MMGs' tertiary controls, the use of optimization algorithms to minimize an objective function with equality and inequality constraints allows for powerful control over the system. In this paper, the interior-point algorithm is …

Ent1201 Introduction To Electricity For Live Entertainment Syllabus, Miguel A. Valderrama

Open Educational Resources

No abstract provided.

Effect Of Grain Size And Interface Engineering On The Photovoltaic Performance And Stability Of Perovskite Solar Cells, Abdullah Al Mamun

Electrical & Computer Engineering Theses & Dissertations

Organic-inorganic halide perovskite solar cells (PSCs) have grown rapidly in recent years due to their outstanding optoelectronic properties, high efficiency, and low-cost. However, this emerging solar cell technology is experiencing some challenges such as defects, hysteresis, and long-term stability, which need to be addressed in order to make it commercially available. This dissertation aims to assist in overcoming some of the barriers and is therefore important to the field of perovskite solar cells.

Initially, this dissertation focuses on investigating the role of grain interiors (GIs) and grain boundaries (GBs) of perovskite film using chemically, spatially, and temporally resolved measurements at …

Plasma Treatment Method For Ohmic Contacts On Zinc Oxide Thin Film Transistors, Blaine Z. Underwood

Theses and Dissertations

This research utilizes plasma treatments as a method to decrease the contact resistance on zinc oxide (ZnO) thin film transistors (TFT). In recent years, researchers have achieved gigahertz RF switch cutoff frequency with ZnO TFTs. To further increase the cutoff frequency, the total resistance of this device must be minimized. Modern ZnO TFTs are fabricated with submicron channel lengths, which contains minimal resistance due to the TFT channel, making contact resistance significant to the total resistance of the device. This research developed a method to integrate plasma treatments into the fabrication of ZnO TFT to decrease the contact resistance, thus …

A Systematic Study On The Effects Of Dimensional And Materials Tolerances On Permanent Magnet Synchronous Machines Based On The Ieee Std 1812, Narges Taran, Vandana Rallabandi, Dan M. Ionel, Ping Zhou, Mark Theile, Greg Heins

Power and Energy Institute of Kentucky Faculty Publications

In the process of designing and manufacturing an electrical machine, a systematic study of dimensional and material tolerances is of the utmost importance. This paper proposes a systematic method by which the effect of design specification variations on permanent magnet (PM) synchronous machine performance may be identified and quantified. The method combines design of experiments techniques, open-circuit and short-circuit physical measurements, and virtual test simulations conducted based on the recently approved IEEE Std 1812 testing guide. Three case studies, two provided by a spoke-type PM radial field machine configuration, in two designs with different electromagnetic loading, and an axial flux …

Microgrid Renewable Energy Integration, Do Quang Thanh Vo

Electrical Engineering

The Microgrid is a small-scale electrical system that is designed to give Cal Poly students hands-on experience on power generation, system protection, distribution, and automation that would otherwise be very difficult to experiment in a large-scale model.

To closely replicate the modern electrical grid, a renewable energy source shall be added to the Microgrid in conjunction with the existing synchronous generators. Electrical engineering student, Virginia Yan initiated this effort, namely Grid-Tied Solar System project [1], by designing and constructing a set of solar panels and microinverter for future connection to the Microgrid. The scope of Virginia’s project was, however, limited …

36% Reduction In Fuel Resupply Using A Hybrid Generator & Battery System For An Austere Location, David J. Chester, Torrey J. Wagner, Douglas S. Dudis

Faculty Publications

The DOD energy policy is to increase energy security resiliency, and mitigate costs in the use and management of energy^[1] Forward operating bases (FOBs) are remote, austere base camps that support an operationally defined mission with a limited or no ability to draw from an energy grid and have historically relied on diesel-powered generators for the primary production of energy.^[2] Generators are sized to meet a theoretical peak demand, but steady state loads are far below this peak, resulting in under-loaded generators.^[3] Under-loaded diesel generators decrease efficiency and increase the need for maintenance, affecting the lifespan of …

Current Status And Prospect Of Battery Configuration In Li-S System, Jia-Hang Chen, Hui-Jun Yang, Cheng Guo, Jiu-Lin Wang

Journal of Electrochemistry

Commercial lithium-ion batteries (LIBs) are incapable of satisfying the increasing demand for emerging electronic devices due to their limited energy density. Among the next-generation batteries, lithium-sulfur (Li-S) batteries are becoming a promising energy-storage system due to their high theoretical energy density and natural abundance of sulfur. However, the shuttle of soluble polysulfide intermediates between two electrodes, as well as the problem on Li metal anode,lower the utilization of active material and lead to the loss of specific capacity and rapid capacity fading. All the above challenges limit the further application of Li-S batteries. Recently, various novel battery configurations have been …

Recent Progress On Tio2-Based Anode Materials For Sodium-Ion Batteries, Si-Tian Lian, Jian-Shuai Lv, Qiang Yu, Guang-Wu Hu, Zhuo Chen, Liang Zhou, Li-Qiang Mai

Journal of Electrochemistry

Titanium dioxide (TiO₂) represents a stable, low-cost, and nontoxic anode material for sodium-ion batteries (SIBs). However, the low electrical conductivity limits its electrochemical activity (specific capacity) and rate capability, hindering its widespread applications. In this article, we show that different crystal forms of TiO₂ have different pore structures, resulting in the distinct sodium storage capacities. Accordingly, the article introduces how TiO₂ microstructures influence sodium storage. The nanoparticle structure can improve the rate performance of the material due to its short ion diffusion distance, and the internal cavity of the hollow structure is beneficial to cycle stability. …

Recent Progress In Key Materials For Room-Temperature Sodium-Ion Batteries, Fan-Fan Wang, Xiao-Bin Liu, Long Chen, Cheng-Cheng Chen, Yong-Chang Liu, Li-Zhen Fan

Journal of Electrochemistry

Sodium-ion batteries (SIBs) have attracted tremendous attention in large-scale energy storage applications due to their resource advantages. However, Na+ is larger and heavier than Li+, which will limit its reversible reaction with the electrode materials and result in poor electrochemical performance. Thus, developing stable and high-efficiency electrode materials is the key to promoting the practical application of SIBs. Furthermore, the optimization of electrolyte is essential for the construction of high-safety and long-lifespan SIBs. In this review, we mainly summarize the recent advancements of electrode materials and electrolytes for room-temperature SIBs and discuss their challenges and possible resolution strategies. We hope …

Recent Developments In Surface/Interface Modulation And Structure-Performance Relationship Of Cathode Catalysts For Li-Air Batteries, Rui Gao, Jun-Kai Wang, Zhong-Bo Hu, Xiang-Feng Liu

Journal of Electrochemistry

Lithium-air battery has been considered to be one of the most promising secondary battery systems because of its high energy density. However, the sluggish kinetics of the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) on the cathode, and the high overpotential, poor cycle stability and low rate capacity have severely blocked the development and application of Li-air battery. One of the effective strategies to alleviate these issues is to develop cathode catalysts for Li-air batteries. The design and development of bifunctional cathode catalysts with high activity and efficiency on both ORR and OER is highly desired for Li-air …

A Comparative Study Of Pre-Lithiated Hard Carbon And Soft Carbon As Anodes For Lithium-Ion Capacitors, Zhao Li, Xian-Zhong Sun, Wen-Jie Liu, Xiong Zhang, Kai Wang, Yan-Wei Ma

Journal of Electrochemistry

Lithium-ion capacitor (LIC) has emerged to be one of the most promising electrochemical energy storage devices. Presently, activated carbon (AC) is the mostly used cathode material for LIC. Nevertheless, various carbonaceous materials can be used as anode materials, such as hard carbon (HC) and soft carbon (SC). Therefore, HC and SC with different structural and electrochemical characteristics have been investigated as the anode materials of LICs in this work. Compared with the HC electrode, the SC electrode showed higher electronic conductivity and reversible capacity. The rate capabilities of the two carbonaceous materials as a function of coating thickness have been …

Cvd Preparation And Application Of 3d Graphene In Electrochemical Energy Storage, Yong-Kang Xia, Ming-Yuan Gu, Hong-Guan Yang, Xin-Zhi Yu, Bing-An Lu

Journal of Electrochemistry

Three-dimensional (3D) graphene combinations with the excellent intrinsic properties of graphene and the 3D micro/nano porous structures provide a graphene foam with high specific surface area, excellent mechanical strength and fast electron and mass transports. The 3D graphene foam and its composite nanomaterials are widely used in the fields of nano-electronics, energy storage, chemical and biological sensing. The 3D graphene foam prepared by chemical vapor deposition (CVD) method is of high purity and crystallinity.  In this review, a brief overview in the CVD preparations of 3D graphene and properties of CVD prepared 3D graphene based nanomaterials in electrochemical energy storage …