Electromagnetics and Photonics Commons^™

Incorporation Of Zinc In Pre-Alloyed Cuin[Zn]S2/Zns Quantum Dots, Jean Carlos Morales Orocu

Graduate Theses and Dissertations

Since the early 2000s heavy-metal-free quantum dots (QDs) such as CuInS2/ZnS have attempted to replace CdSe, their heavy-metal-containing counterparts. CuInS2/ZnS is synthesized in a two-step process that involves the fabrication of CuInS2 (CIS) nanocrystals (NCs) followed by the addition of zinc precursors. Instead of the usual core/shell architecture often exhibited by binary QDs, coating CIS QDs results in alloyed and/or partially alloyed cation-exchange (CATEX) QDs. The effect that zinc has on the properties of CIS NCs was studied by incorporating zinc during the first step of the synthesis. Different In:Cu:Zn ratios were employed in this study, maintaining a constant 4:1 …

Using The Inelastic Background In Hard X-Ray Photoelectron Spectroscopy For A Depth-Resolved Analysis Of The Cds / Cu(In,Ga)Se < Inf > 2 < / Inf > Interface, Dirk Hauschild, Ralph Steininger, Dimitrios Hariskos, Wolfram Witte, Sven Tougaard, Clemens Heske, Lothar Weinhardt

Chemistry and Biochemistry Faculty Research

The inelastic background of hard x-ray photoelectron spectroscopy data is analyzed to paint a depth-resolved picture of the CdS/Cu(In,Ga)Se2 (CdS/CIGSe) layer structure. The CdS/CIGSe interface is the central component in next-generation chalcopyrite thin-film photovoltaic devices. By analyzing both, the (unscattered) core-level peaks and the inelastic background, and by varying the excitation photon energy from 2.1 up to 14 keV, we can derive photoemission information over a broad range of electron kinetic energies and, hence, sampling depths. With this complementary information, the CdS film thickness of a CdS/CIGSe interface can be accurately determined as a function of the CdS deposition time. …

Growth Of Pseudomorphic Gesn At Low Pressure With Sn Composition Of 16.7%, Joshua Grant, Grey Abernathy, Oluwatobi Olorunsola, Solomon Opeyemi Ojo, Sylvester Amoah, Emmanuel Wangila, Samir K. Saha, Abbas Sabbar, Wei Du, Murtadha Alher, Bao-Hua Li, Shui-Qing Yu

Physics Faculty Publications and Presentations

Group-IV alloy GeSn holds great promise for the high-performance optoelectronic devices that can be monolithically integrated on Si for near- and mid-infrared applications. Growth of GeSn using chemical vapor deposition technique with various Sn and Ge precursors has been investigated worldwide. To achieve relatively high Sn incorporation, the use of higher pressure and/or higher order Ge hydrides precursors were reported. In this work, we successfully demonstrated the growth of high-quality GeSn with Sn composition of 16.7% at low pressure of 12 Torr. The alloy was grown using the commercially available GeH₄ and SnCl₄ precursors via a chemical vapor …

Polarization-Resolved Extreme-Ultraviolet Second-Harmonic Generation From Linbo3, Can B. Uzundal, Sasawat Jamnuch, Emma Berger, Clarisse Woodahl, Paul Manset, Yasuyuki Hirata, Toshihide Sumi, Angelique Amado, Hisazumi Akai, Yuya Kubota, Shigeki Owada, Kensuke Tono, Makina Yabashi, John W. Freeland, Craig P. Schwartz, Walter S. Drisdell

Nevada Extreme Conditions Laboratory Faculty Research

Second harmonic generation (SHG) spectroscopy ubiquitously enables the investigation of surface chemistry, interfacial chemistry, as well as symmetry properties in solids. Polarization-resolved SHG spectroscopy in the visible to infrared regime is regularly used to investigate electronic and magnetic order through their angular anisotropies within the crystal structure. However, the increasing complexity of novel materials and emerging phenomena hampers the interpretation of experiments solely based on the investigation of hybridized valence states. Here, polarization-resolved SHG in the extreme ultraviolet (XUV-SHG) is demonstrated for the first time, enabling element-resolved angular anisotropy investigations. In noncentrosymmetric LiNbO3, elemental contributions by lithium and niobium are …

Single-Molecule Localization Microscopy Of 3d Orientation And Anisotropic Wobble Using A Polarized Vortex Point Spread Function, Tianben Ding, Matthew D. Lew

Electrical & Systems Engineering Publications and Presentations

Within condensed matter, single fluorophores are sensitive probes of their chemical environments, but it is difficult to use their limited photon budget to image precisely their positions, 3D orientations, and rotational diffusion simultaneously. We demonstrate the polarized vortex point spread function (PSF) for measuring these parameters, including characterizing the anisotropy of a molecule’s wobble, simultaneously from a single image. Even when imaging dim emitters (∼500 photons detected), the polarized vortex PSF can obtain 12 nm localization precision, 4°–8° orientation precision, and 26° wobble precision. We use the vortex PSF to measure the emission anisotropy of fluorescent beads, the wobble dynamics …

Resampling And Super-Resolution Of Hexagonally Sampled Images Using Deep Learning, Dylan Flaute, Russell C. Hardie, Hamed Elwarfalli

Electrical and Computer Engineering Faculty Publications

Super-resolution (SR) aims to increase the resolution of imagery. Applications include security, medical imaging, and object recognition. We propose a deep learning-based SR system that takes a hexagonally sampled low-resolution image as an input and generates a rectangularly sampled SR image as an output. For training and testing, we use a realistic observation model that includes optical degradation from diffraction and sensor degradation from detector integration. Our SR approach first uses non-uniform interpolation to partially upsample the observed hexagonal imagery and convert it to a rectangular grid. We then leverage a state-of-the-art convolutional neural network (CNN) architecture designed for SR …

Recent Advances In Silver Nanoparticle-Based Electrochemical Sensors For Determining Organic Pollutants In Water, Ziad Khalifa, Moustafa Zahran, Magdy Zahran, Magdi Abdelazzem

Chemical Engineering

Water pollutants have attracted great attention because of their negative effect on human health. Accordingly, various analytical techniques have been investigated to detect water pollutants as a preliminary step for their control. This review highlights silver nanoparticles (AgNPs) as promising electrochemical probes studied for detecting organic pollutants. Electrochemical sensors can be fabricated by modifying electrode surfaces using AgNPs via different techniques, such as electrochemical deposition, drop casting, spin coating, sticking, and transfer sticking, as well as carbon paste-based modification. AgNPs at electrode surfaces can be identified by their stripping to form Ag+ with a particular oxidation peak. Additionally, they can …

A Unified Framework Of Deep Learning-Based Facial Expression Recognition System For Diversified Applications, Sanoar Hossain, Saiyed Umer, Vijayan K. Asari, Ranjeet Kumar Rout

Electrical and Computer Engineering Faculty Publications

This work proposes a facial expression recognition system for a diversified field of appli- cations. The purpose of the proposed system is to predict the type of expressions in a human face region. The implementation of the proposed method is fragmented into three components. In the first component, from the given input image, a tree-structured part model has been applied that predicts some landmark points on the input image to detect facial regions. The detected face region was normalized to its fixed size and then down-sampled to its varying sizes such that the advantages, due to the effect of multi-resolution …

Characterization Of Anisotropic Materials Using Scattered Field Measurements, Hirsch M. Chizever

Theses and Dissertations

This research uses monostatic far-zone scattered field measurements to estimate the permittivity of biaxial materials at X-Band. Utilizing Radar Cross Section (RCS) measurement techniques, this effort examines the efficacy of whole-sample TEM illumination in the estimation of anisotropic permittivity, in contrast with traditional subsample illumination methods. The research examines the impact that dielectric supports have on measurement error and uncertainty in permittivity estimates. Following an incremental approach, the research first demonstrates successful estimation of permittivity for isotropic spheres followed by a Teflon isotropic cube. Finally, the method is applied to uniaxial and biaxial cubes whose anisotropic permittivity is validated through …

A Compact 1200 V, 700 A, Igbt-Based Pulse Generator For Repetitive Transcranial Magnetic Stimulation In Vivo Laboratory Experiments On Small Animals, Daniel Senda, Haley Strong, Dustin Hines, Rochelle Hines, R. Jacob Baker

Psychology Faculty Research

An insulated-gate bipolar transistor (IGBT) pulse generator for repetitive transcranial magnetic stimulation used for in vivo laboratory experiments on small animals, such as mice, is reported. The pulse generator is based upon an IGBT that can switch 700 A of current for 1 ms and that has a DC breakdown voltage of 1200 V. The duration of the design’s output pulse is controlled by, and follows, an input trigger pulse. The voltage amplitude of the output pulses is determined by an external high-voltage power supply and the energy stored in a 330 µF capacitor bank. The approach enables the amplitude …

The Effect Of A Ferrite-Core Relay Vs. An Air-Core Relay On The Output Power Characteristics Of A Three-Coil Wireless Power Transfer System, Jakob L. White

University Honors Theses

The purpose of this thesis is to determine the effect of using a ferrite-core relay on the output power characteristics of a three-coil, parallel-tuned, domino-resonator wireless power transfer (WPT) system in comparison to the effect of using an air-core relay in such a system. First, a general mathematical model is presented to describe both the ferrite-core-relay system and the air-core-relay system and to calculate their output power characteristics for seven different resistive loads at each of five different distance configurations between the coils. Next, experimental results are analyzed and compared to the mathematical results to confirm model accuracy. Finally, the …

Wavelength And Power Dependence On Multilevel Behavior Of Phase Change Materials, Gary A. Sevison, Joshua A. Burrow, Haiyun Guo, Andrew M. Sarangan, Joshua R. Hendrickson, Imad Agha

Electro-Optics and Photonics Faculty Publications

We experimentally probe the multilevel response of GeTe, Ge2Sb2Te5 (GST), and 4% tungsten-doped GST (W-GST) phase change materials (PCMs) using two wavelengths of light: 1550 nm, which is useful for telecom-applications, and near-infrared 780 nm, which is a standard wavelength for many experiments in atomic and molecular physics. We find that the materials behave differently with the excitation at the different wavelengths and identify useful applications for each material and wavelength. We discuss thickness variation in the thin films used as well and comment on the interaction of the interface between the material and the substrate with regard to the …

Study And Design Of Array And Beamsteering Antennas For Millimeter Wave Band Application, Saeideh Shad

Boise State University Theses and Dissertations

Millimeter wave (mmWave) communication systems have attracted significant interest regarding supporting high data rate of Gigabit/s communications for the new generation of wireless communication networks. MmWave communication systems have frequency ranges in between 30 and 300 GHz wherein an enormous amount of unused bandwidth is available. Although the available bandwidth of mmWave frequencies is promising for high data rate communications, the propagation characteristics of mmWave frequencies are significantly different from microwave frequency band in terms of path loss, diffraction and blockage, and atmospheric absorption. In general, the overall losses of mmWave signals are significantly larger than that of microwave signals …

Experimental Observation Of Topological Z2 Excitonpolaritons In Transition Metal Dichalcogenide Monolayers, Mengyao Li, Ivan Sinev, Fedor Benimetskiy, Tatyana Ivanova, Ekaterina Khestanova, Svetlana Kiriushechkina, Anton Vakulenko, Sriram Guddala, Maurice Skolnick, Vinod M. Menon, Dmitry Krizhanovskii, Andrea Alù, Anton Samusev, Alexander B. Khanikaev

Publications and Research

The rise of quantum science and technologies motivates photonics research to seek new platforms with strong light-matter interactions to facilitate quantum behaviors at moderate light intensities. Topological polaritons (TPs) offer an ideal platform in this context, with unique properties stemming from resilient topological states of light strongly coupled with matter. Here we explore polaritonic metasurfaces based on 2D transition metal dichalcogenides (TMDs) as a promising platform for topological polaritonics. We show that the strong coupling between topological photonic modes of the metasurface and excitons in TMDs yields a topological polaritonic Z₂ phase. We experimentally confirm the emergence of one-way …

Optical Switching Performance Of Thermally Oxidized Vanadium Dioxide With An Integrated Thin Film Heater, Andrew M. Sarangan, Gamini Ariyawansa, Ilya Vitebskiy, Igor Anisimov

Electro-Optics and Photonics Faculty Publications

Optical switching performance of vanadium dioxide produced by thermal oxidation of vanadium is presented in this paper. A 100nm thick vanadium was oxidized under controlled conditions in a quartz tube furnace to produce approximately 200nm thick VO2. The substrate was appropriately coated on the front and back side to reduce reflection in the cold state, and an integrated thin film heater was fabricated to allow in-situ thermal cycling. Electrical measurements show a greater than three orders of magnitude change in resistivity during the phase transition. Optical measurements exhibit 70% transparency at 1500nm and about 15dB extinction across a wide spectral …

Computational Modeling Of Black Phosphorus Terahertz Photoconductive Antennas Using Comsol Multiphysics With Experimental Comparison Against A Commercial Lt-Gaas Emitter, Jose Isaac Santos Batista

Graduate Theses and Dissertations

This thesis presents computational models of terahertz (THz) photoconductive antenna (PCA) emitter using COMSOL Multiphysics commercial package. A comparison of the computer simulated radiated THz signal against that of an experimentally measured signal of commercial reference LT-GaAs emitter is presented. The two-dimensional model (2D) aimed at calculating the photoconductivity of a black phosphorus (BP) PCA at two laser wavelengths of 780 nm and 1560 nm. The 2D model was applied to the BP PCA emitter and the LT-GaAs devices to compare their simulated performance in terms of the photocurrent and radiated THz signal pulse. The results showed better performance of …

Fabrication And Characterization Of Photodetector Devices Based On Nanostructured Materials: Graphene And Colloidal Nanocrystals, Wafaa Gebril

Graduate Theses and Dissertations

Photodetectors are devices that capture light signals and convert them into electrical signals. High performance photodetectors are in demand in a variety of applications, such as optical communication, security, and environmental monitoring. Among many appealing nanomaterials for novel photodetection devices, graphene and semiconductor colloidal nanocrystals are promising candidates because of their desirable and unique properties compared to conventional materials.

Photodetector devices based on different types of nanostructured materials including graphene and colloidal nanocrystals were investigated. First, graphene layers were mechanically exfoliated and characterized for device fabrication. Self-powered few layers graphene phototransistors were studied. At zero drain voltage bias and room …

Distributed Modeling Approach For Electrical And Thermal Analysis Of High-Frequency Transistors, Amirreza Ghadimi Avval

Graduate Theses and Dissertations

The research conducted in this dissertation is focused on developing modeling approaches for analyzing high-frequency transistors and present solutions for optimizing the device output power and gain. First, a literature review of different transistor types utilized in high-frequency regions is conducted and gallium nitride high electron mobility transistor is identified as the promising device for these bands. Different structural configurations and operating modes of these transistors are explained, and their applications are discussed. Equivalent circuit models and physics-based models are also introduced and their limitations for analyzing the small-signal and large-signal behavior of these devices are explained. Next, a model …

Use Of The Igbt Module In The Active Region To Design A High Current Active Filter, Jorge F. Galarraga

Graduate Theses and Dissertations

Particle accelerators require high-precision magnetic fields on the order or 100ppm or less. This implies that the precision of the associated electrical current in the electromagnet that generates these fields should be smaller than 100ppm. However, conventional switching power supplies cannot offer this precision due to the frequency limitation of the switches. This research considers the use of power electronics devices operating in a linear as an alternative solution to meet the requirements of particle accelerator electromagnets.

This thesis presents the study of an insulated-gate bipolar transistor (IGBT) driver using a new control method that linearizes the IGBT’s collector-emitter voltage …

Experimental And Analysis Of Electromagnetic Characterization Of Biological And Non-Biological Materials In Microwave, Millimeter-Wave, And Terahertz Frequency Bands, Nagma Vohra

Graduate Theses and Dissertations

The goal of this research is to characterize the electromagnetic properties of biological and non-biological materials at terahertz (THz), millimeter-wave, and microwave frequency bands. The biological specimens are measured using the THz imaging and spectroscopy system, whereas the non-biological materials are measured using the microwave and millimeter-wave free-space system. These facilities are located in the Engineering Research Center at the University of Arkansas. The THz imaging system (TPS 3000) uses a Ti-Sapphire laser directed on the photoconductive antennas to generate a THz time domain pulse. Upon using the Fourier Transform, the spectrum of the pulsed THz signal includes frequencies from …

Comparative Study Of Nano-Rod And Nano-Sphere Based Localized Surface Plasmon Resonance Refractive Index Biosensors, Mariam M. Moussilli M. M. Moussilli, Abdul Rahman El Falou

BAU Journal - Science and Technology

Localized Surface Plasmon Resonance (LSPR) waves generated by the interaction of light with noble metal nanoparticles has been of great interest in recent years due to the high sensitivity of the extinction spectra of these nanoparticles to the medium's surrounding refractive index up to the atomic level.

In this article, we simulate the extinction spectra of noble metal sphere and rod nanoparticles in order to study the effect of the geometrical shape and size of the nanoparticle on the sensitivity and detection accuracy performance parameters of the extinction spectra. We also simulated the response of the sphere and rod nanoparticle's …

All-Optical Nonreciprocity Due To Valley Polarization Pumping In Transition Metal Dichalcogenides, Sriram Guddala, Yuma Kawaguchi, Filipp Komissarenko, Svetlana Kiriushechkina, Anton Vakulenko, Kai Chen, Andrea Alù, Vinod M. Menon, Alexander B. Khanikaev

Publications and Research

Nonreciprocity and nonreciprocal optical devices play a vital role in modern photonic technologies by enforcing one-way propagation of light. Here, we demonstrate an all-optical approach to nonreciprocity based on valley-selective response in transition metal dichalcogenides (TMDs). This approach overcomes the limitations of magnetic materials and it does not require an external magnetic field. We provide experimental evidence of photoinduced nonreciprocity in a monolayer WS2 pumped by circularly polarized (CP) light. Nonreciprocity stems from valley-selective exciton population, giving rise to nonlinear circular dichroism controlled by CP pump fields. Our experimental results reveal a significant effect even at room temperature, despite considerable …

On-Chip Nanoscale Plasmonic Optical Modulators, Abdalrahman Mohamed Nader Abdelhamid

Theses and Dissertations

In this thesis work, techniques for downsizing Optical modulators to nanoscale for the purpose of utilization in on chip communication and sensing applications are explored. Nanoscale optical interconnects can solve the electronics speed limiting transmission lines, in addition to decrease the electronic chips heat dissipation. A major obstacle in the path of achieving this goal is to build optical modulators, which transforms data from the electrical form to the optical form, in a size comparable to the size of the electronics components, while also having low insertion loss, high extinction ratio and bandwidth. Also, lap-on-chip applications used for fast diagnostics, …

Cross-Junction Based Metasurfaces: A Roadmap To Fano Resonances, Mirna Soliman

Theses and Dissertations

The first part of the thesis presents a summary of the classification of materials, followed by the development of metamaterials and their salient role. Then, a study of metamaterials and the evolution of these 3D structures to 2D, known as metasurfaces, have been discussed. Moreover, the physics and practical interest behind Fano resonance have been discussed. Furthermore, the physical fundamentals guiding the performance of both the metamaterials and metasurfaces, including the temporal coupled-mode theory and the generalized laws of reflection and refraction, have been intensely investigated, along with some of the outstanding properties of the metamaterials. Then, a comparison between …

Graphene As A Shielding Material For Sar Reduction In Human Head Using Rectangular And Circular Patch Antenna, Alka Singla Er., Anupma Marwaha Dr., Sanjay Marwaha Dr.

Karbala International Journal of Modern Science

Nanomaterials pave the way for better performance in wireless applications due to their unique properties. Nowadays, these have been used as shield material in dipole antennas for a solution of reduction in SAR value. This work proposes the use of emerging graphene nanomaterial by comparing the performance for two different shapes of patch antenna namely rectangular and circular patch. With the growth in technology, the protection of human health is also mandatory so the work is planned to use graphene as a shielding material for SAR reduction in the human brain and it is proved that for rectangular and circular …

Review And Analysis Of Methods For Measuring Concentration Of Suspended Substances And Active Sludge During Biological Treatment Of Waste Water, Maxsud Maxmudov, Siroj Nurov, Zafar Qo'ziev, Sanjar Sidiqov

Scientific-technical journal

This work analyzes and compares the measuring and technical characteristics of methods for measuring and controlling the parameters of activated sludge in the processes of biological wastewater treatment. As methods for measuring the concentration of activated sludge, methods such as the optical method, the ultrasonic method and the method for measuring the nuclear density of a liquid are considered. The principles of operation of each of these methods are illustrated with graphic drawings for more clarity of the interaction of the measuring signal with the particles of the measured medium. At the end of the work, conclusions on the characteristics …

Led-Based Solar Simulator, Jonathan E. Honrada

Electrical Engineering

Solar simulators are great laboratory tools that help users conduct tests with solar cells indoors. Conventional solar simulators typically use xenon arc bulbs as a light source, which can have considerable disadvantages. Recent projects have sought to design and implement LED-based solar simulators, as they are more power-efficient, inexpensive, and durable.

Based on these advantages, the goal of this project is to create an LED-based solar simulator that can replicate the characteristics of solar light, but also be tunable with controls. This broadens the testing capabilities of the device, allowing users to conduct tests with more narrow spectrums of light …

Ultra-High-Energy Neutrino Detection Antenna Simulations, Nicholas C. Garcia

Electrical Engineering

Neutrinos allow researchers to investigate high-energy galactic phenomena, such as supernovae and black holes. Neutrinos interact with their surroundings via the weak nuclear force and therefore, travel unattenuated through space and are not deflected by electromagnetic fields. However, they do rarely interact with other particles. When neutrinos interact with nucleons (protons or neutrons) in a dielectric medium (i.e.: ice sheets), they are detectable through a cone of coherent electromagnetic radiation (Askaryan Radiation) created by the particle shower generated from the neutrino interaction [1]. The Radio Neutrino Observatory in Greenland (RNO-G) detects UHE neutrinos greater than 100 PeV (10¹⁵ eV) …

Understanding Diffusion And Electrochemical Reduction Of Li+ Ions In Liquid Lithium Metal Batteries, Witness Martin, Yang Tian, Jie Xiao

Chemistry & Biochemistry Faculty Publications and Presentations

Lithium metal has drawn significant interest as an anode material for next generation lithium (Li) batteries. However, due to its propensity to form dendrites in commonly used electrolytes during repeated cycling, it has not yet been commercialized in secondary batteries. The formation of a Li protrusion is determined by the relative speed of Li+ ions being reduced and how fast they can be replenished in the vincinity of electrode. However, it is very difficult to quantify such kinetic parameters of Li+ ion in different electrolytes, not mentioning the identification of the desired electrolyte recipe to mitigate Li dendrite formation. Herein, …

Pepblock Builder Vr – An Open-Source Tool For Gaming-Based Bio-Edutainment In Interactive Protein Design, Venkata V. B. Yallapragada, Tianshu Xu, Sidney P. Walker, Sabin Tabirca, Mark Tangney

Cappa Publications

Proteins mediate and perform various fundamental functions of life. This versatility of protein function is an attribute of its 3D structure. In recent years, our understanding of protein 3D structure has been complemented with advances in computational and mathematical tools for protein modelling and protein design. 3D molecular visualisation is an essential part in every protein design and protein modelling workflow. Over the years, stand-alone and web-based molecular visualisation tools have been used to emulate three-dimensional view on computers. The advent of virtual reality provided the scope for immersive control of molecular visualisation. While these technologies have significantly improved our …