Electromagnetics and Photonics Commons^™

Consideration Of Dispersion And Group Velocity Dispersion In The Determination Of Velocities Of Electromagnetic Propagation, Monish Ranjan Chatterjee, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

Electromagnetic (EM) propagation velocities play an important role in the determination of power and energy flow in materials and interfaces. It is well known that group and phase velocities need to be in opposition in order to achieve negative refractive index.

Recently, we have shown that considerable differences may exist in phase, group and signal/energy velocities for normal and anomalous dispersion, especially near dielectric resonances. This paper examines the phase and group velocities in the presence of normal and anomalous dispersion, and group velocity dispersion (GVD), which requires introduction of the second order coefficient in the permittivity and permeability models.

Enhanced Light Extraction Efficiency From Gan Light Emitting Diodes Using Photonic Crystal Grating Structures, Simeon S. Trieu

Master's Theses

Gallium nitride (GaN) light emitting diodes (LED) embody a large field of research that aims to replace inefficient, conventional light sources with LEDs that have lower power, higher luminosity, and longer lifetime. This thesis presents an international collaboration effort between the State Key Laboratory for Mesoscopic Physics in Peking University (PKU) of Beijing, China and the Electrical Engineering Department of California Polytechnic State University, San Luis Obispo. Over the course of 2 years, Cal Poly’s side has simulated GaN LEDs within the pure blue wavelength spectrum (460nm), focusing specifically on the effects of reflection gratings, transmission gratings, top and bottom …

Aperture Coupled Microstrip Antenna Design And Analysis, Michael Paul Civerolo

Master's Theses

A linearly-polarized aperture coupled patch antenna design is characterized and optimized using HFSS antenna simulation software. This thesis focuses on the aperture coupled patch antenna due to the lack of fabrication and tuning documentation for the design of this antenna and its usefulness in arrays and orthogonally polarized communications. The goal of this thesis is to explore dimension effects on aperture coupled antenna performance, to develop a design and tuning procedure, and to describe performance effects through electromagnetic principles.

Antenna parameters examined in this study include the dimensions and locations of the substrates, feed line, ground plane coupling slot, and …

Improved Rf Power Extraction From 1.55um Ge-On-Soi Pin Photodiodes With Load Impedance Optimization, Andrew L. Huard

Master's Theses

VLSI miniaturization has created the need for high-density, low-cost, monolithically-integrated optical interconnects. High output power photodetectors are needed to directly drive load circuitry, which improves the noise performance and dynamic range of optical communications links by eliminating a post amplifier stage. Elimination of the post amplifier also reduces circuit cost and complexity. A new Si-Ge PIN waveguide photodiode with 31GHz bandwidth and 93% quantum efficiency at 1550nm has been developed by Yin et al., which was fabricated using standard CMOS processes on a Silicon substrate. This thesis demonstrates a method for improving the RF power extraction from these photodiodes by …

Standalone Antenna Demonstration System, Alexander James Hempy

Master's Theses

Antenna systems play a significant role in today’s electronic communications. They are essential for cell phones, satellites, radio, and radar among many other important applications. This paper describes the design, assembly, and operation of an antenna demonstration system designed to instill interest in the field of antenna design among high school and undergraduate college students. The system is portable, supplied solely by DC power supplies, easily reproducible, and includes rotational axes to illustrate antenna performance limitations and requirements. It provides a visual indication of wireless signal strength and demonstrates several antenna performance characteristics including polarization, gain and directivity, radiation patterns …

Novel Techniques For The Integration Of Antennas And Photovoltaic Cells, Maria Roo Ons, S. Shynu, Max Ammann, Sarah Mccormack, Brian Norton

Conference Papers

Various novel approaches to the integration of antenna and photovoltaic technologies are proposed. These include the use of polycrystalline solar cells as groundplane for microstrip patch antennas as well as for reflectors of half-wave dipole antennas. Transparent materials were also evaluated as antenna radiating elements, allowing greater solar efficiency. A novel technique illustrating how emitter-wrap-through rear contact solar cells can be used as a folded-dipole antenna, which is located in the focal line of a parabolic solar concentrator, to provide high solar efficiency as well as high antenna gain, is presented.

Nuclear Electromagnetic Currents In Chiral Effective Field Theory, Saori Pastore

Physics Theses & Dissertations

A nucleon-nucleon potential and consistent nuclear electromagnetic currents are derived in chiral effective field theory retaining pions and nucleons as explicit degrees of freedom. The calculation of the potential is carried out up to next-to-next-to leading order (N²LO), while the currents include up to N³LO corrections. The potential at N² LO and currents at N³LO consist of two-pion-exchange and contact contributions. The currents are then utilized to study a number of low-energy electromagnetic observables induced by magnetic dipole transitions, such as the deuteron and trinucleon magnetic moments and the np, nd and n …

Application Of The Three Short Calibration Technique In A Low Frequency Focus Beam System, William E. Gunn Jr.

Theses and Dissertations

Electromagnetic material characterization is the process of determining the constitutive parameters of matter. In simple media, these parameters are permittivity and permeability. Characterization of these values is often accomplished through the use of waveguides, transmission lines, coaxial cables, and resonant cavities. Free space measurements systems are employed since they are non destructive (i.e., no sample machining is required) and broadband. Traditionally, time domain gating is utilized to mitigate systematic errors. However, an artifact of this calibration technique is band edge corruption due to data windowing. The goal of this research is to develop and apply a Three Short Calibration Technique …

Changes To Electrical Conductivity In Irradiated Carbon-Nickel Nanocomposites, David F. Coy

Theses and Dissertations

Pre and post irradiation resistivity and XAFS measurements have been conducted to examine the effects of 0.5 MeV electron irradiations on nickel-carbon composites. Results showed a decrease in surface resistivity in all sample types of 14-30% following irradiation with a total electron exposure of 4 x 10^-16 cm^-2. Results also showed a corresponding decrease in NiO content for the irradiated samples as compared to measurements of non-irradiated samples. Surface resistivity measurement capabilities were established and measurement techniques refined to produce repeatable results of sufficient precision to discern changes in resistivity for an exposure of 2 x 10 …

Response-Calibration Techniques For Antenna-Coupled Infrared Sensors, Peter Krenz

Electronic Theses and Dissertations

Infrared antennas are employed in sensing applications requiring specific spectral, polarization, and directional properties. Because of their inherently small dimensions, there is significant interaction, both thermal and electromagnetic, between the antenna, the antenna-coupled sensor, and the low-frequency readout structures necessary for signal extraction at the baseband modulation frequency. Validation of design models against measurements requires separation of these effects so that the response of the antenna-coupled sensor alone can be measured in a calibrated manner. Such validations will allow confident extension of design techniques to more complex infrared-antenna configurations. Two general techniques are explored to accomplish this goal. The extraneous …

Fast-Response Liquid Crystal Displays, Meizi Jiao

Electronic Theses and Dissertations

After about five decades of extensive material research and device development, followed by massive investment in manufacturing technology, thin-film-transistor liquid-crystaldisplay (TFT-LCD) has finally become the dominant flat panel display technology. Nowadays, LCD performances, such as viewing angle, contrast ratio, and resolution, have reached acceptable levels. The remaining major technical challenges are response time, light efficiency, and sunlight readability. Fast response time is desired to reduce motion blur and to enable field sequential color displays using red (R), green (G), and blue (B) LEDs (light emitting diodes) without noticeable color breakup. Sequential RGB colors would eliminate the commonly used spatial color …

Long Cavity Quantum Dot Laser Diode And Monolithic Passively Mode-Locked Operation, K Shavitranuruk

Electronic Theses and Dissertations

Advantage of the single QD active layer is its potential for very low threshold current density, which in turn can produce low internal optical loss. The low threshold current density and low internal loss thus enable a significant increase in laser diode cavity length. Because of the importance of the threshold current density in heatsinking, future technology of broad-area monolithic laser diodes can be implemented. The dissertation describes the development and the unique characteristics of single QD active layer laser with long cavity. The data are presented on single layer QD laser diodes that reach threshold current densities values of …

Fabrication Of Integrated Optofluidic Circuits In Chalcogenide Glass Using Femtosecond Laser Direct Writing, Troy P. Anderson

Electronic Theses and Dissertations

Femtosecond laser direct writing (FLDW) is a versatile process that uses focused femtosecond pulses to modify the physical structure of a material, which can result in a shift of optical properties such as the linear and nonlinear refractive index. If the photon energy of the femtosecond pulses lies below the material bandgap, nonlinear absorption rather than linear absorption becomes the dominant mechanism of energy transfer to the material. In this manner, a focused femtosecond pulse train can be used to fabricate functional features such as optical waveguides, diffractive optical elements, or micro-fluidic elements within the volume of a transparent medium. …

Nonlinear Absorption And Free Carrier Recombination In Direct Gap Semiconductors, Peter D. Olszak

Electronic Theses and Dissertations

Nonlinear absorption of Indium Antimonide (InSb) has been studied for many years, yet due to the complexity of absorption mechanisms and experimental difficulties in the infrared, this is still a subject of research. Although measurements have been made in the past, a consistent model that worked for both picosecond and nanosecond pulse widths had not been demonstrated. In this project, temperature dependent two-photon (2PA) and free carrier absorption (FCA) spectra of InSb are measured using femtosecond, picosecond, and nanosecond IR sources. The 2PA spectrum is measured at room temperature with femtosecond pulses, and the temperature dependence of 2PA and FCA …

Electroless Deposition Of Superconducting Magnesium Diboride Thin Films On Various Substrates, Khrupa Saagar Vijayaragavan

Wayne State University Theses

ABSTRACT

ELECTROLESS DEPOSITION OF SUPERCONDUCTING MAGNESIUM DIBORIDE THIN FILMS ON VARIOUS SUBSTRATES

by

KHRUPA SAAGAR VIJAYARAGAVAN

MAY 2010

Advisor: Dr. Susil K Putatunda

Dr. Gavin Lawes

Major: Chemical Engineering

Degree: Masters of Science

Superconducting thin films of magnesium diboride were synthesized by a novel electroless plating process. Electroless plating shares many similarities to electroplating with the major difference being the absence of a continuous bias voltage. Significantly, this work represents the first investigation where electroless deposition has been used to prepare compounds, as opposed to the elemental metals considered in all previous studies. Magnesium Diboride is a recently discovered superconducting …

Plasmon Enhanced Near-Field Interactions In Surface Coupled Nanoparticle Arrays For Integrated Nanophotonic Devices, Amitabh Ghoshal

Electronic Theses and Dissertations

The current thrust towards developing silicon compatible integrated nanophotonic devices is driven by need to overcome critical challenges in electronic circuit technology related to information bandwidth and thermal management. Surface plasmon nanophotonics represents a hybrid technology at the interface of optics and electronics that could address several of the existing challenges. Surface plasmons are electronic charge density waves that can occur at a metal-dielectric interface at optical and infrared frequencies. Numerous plasmon based integrated optical devices such as waveguides, splitters, resonators and multimode interference devices have been developed, however no standard integrated device for coupling light into nanoscale optical circuits …

New Laser Technologies Analysis Of Quantum Dot And Lithographic Laser Diodes, Abdullah Demir

Electronic Theses and Dissertations

The first part of this dissertation presents a comprehensive study of quantum dot (QD) lasers threshold characteristics. The threshold temperature dependence of a QD laser diode is studied in different limits of p-doping, hole level spacing and inhomogeneous broadening. Theoretical analysis shows that the threshold current of a QD laser in the limit of uniform QDs is not temperature independent and actually more temperature sensitive than the quantum well laser. The results also explain the experimental trends of negative characteristic temperature observed in QD lasers and clarify how the carrier distribution mechanisms inside and among the QDs affect the threshold …

Application Of Antenna Synthesis And Digital Signal Processing Techniques For Active Millimeter-Wave Imaging Systems, Wilson Ariel Caba

Electronic Theses and Dissertations

Millimeter-wave imaging has gathered attention in recent years for its ability to penetrate clothing, thin layers of soils, and certain construction materials. However, image quality remains a challenge that needs to be addressed. One way of improving image quality is by increasing the dimensions of the collecting aperture. A sparse array can be used to synthesize a larger aperture with a limited set of relatively small detectors. In this research we design, build, and test a test-bed having an active source at 94 GHz and an array of coherent detectors, mounted on arms that extend radially on a rotary table. …

Modeling And Design Of A Photonic Crystal Chip Hosting A Quantum Network Made Of Single Spins In Quantum Dots That Interact Via Single Photons, Hubert P. Seigneur

Electronic Theses and Dissertations

In this dissertation, the prospect of a quantum technology based on a photonic crystal chip hosting a quantum network made of quantum dot spins interacting via single photons is investigated. The mathematical procedure to deal with the Liouville-Von Neumann equation, which describes the time-evolution of the density matrix, was derived for an arbitrary system, giving general equations. Using this theoretical groundwork, a numerical model was then developed to study the spatiotemporal dynamics of entanglement between various qubits produced in a controlled way over the entire quantum network. As a result, an efficient quantum interface was engineered allowing for storage qubits …

Design And Simulation Of Silica-On-Silicon Pump/Signal Multiplexer For Hybrid Passive-Active Optical Devices., Alvin Law Wen Pin

Student Works (2010-2019)

This dissertation describes the design and simulation of silica-on-silicon pump/signal multiplexer for hybrid passive-active optical devices. Uniform symmetric directional couplers and planar Bragg gratings were utilized in this work, forming the essential building blocks in a waveguide amplifier. Several designs in relation to the multiplexers are presented in this work, with the simplest application for the directional coupler as a pump/signal multiplexer. A 980/1550 nm and an 800/1310 nm pump/signal multiplexers for erbium doped and bismuth doped waveguide amplifier, respectively were modeled. These couplers were designed and simulated in Rsoft BeamPROP environment, utilizing 3D Finite Difference Beam Propagation Method (FD-BPM) …

Nonlinear Fiber Lasers Using Bismuth Based Erbium Doper Fiber Amplifier., Sharifeh Shahi

Student Works (2010-2019)

A thorough study on Bismuth-based Erbium-doped fiber (Bi-EDF) is presented for wide-band amplifiers and multi-wavelength fiber laser applications. This fiber allows high Erbium ions concentration to be doped without a significant concentration quenching effect. The high refractive index characteristic in the Bi-EDF has broadened the emission spectrum of Erbium ions to achieve a broader gain spectrum up to extended L-band region compared to normal silica-based Erbium-doped fiber (EDF). The Bi-EDFA performances have been investigated in terms of power conversion efficiency (PCE), quantum conversion efficiency (QCE), gain and noise figure. The highest QCE and PCE for a 215 cm long of …

Reflective And Beam-Through Types Of Fiber Optic Sensor For Displacement Measurement., Walaa Fawzi Al–Masri

Student Works (2010-2019)

This dissertation proposes and demonstrates fiber-optic displacement sensor (FODS) theoretically and experimentally using the intensity modulation technique to measure a displacement from a probe and target. The sensor uses a multimode plastic bundled fiber as a probe and He-Ne laser as a source. The performance of the sensor is compared for different type of probe and target. For a pair type bundled fiber, both the experimental and theoretical results exhibit the same type of characteristic features. The front slope sensitivities are obtained at 1.71 and 1.0 mW/μm for the theoretical and experimental approaches respectively, while the back slope sensitivities are …

Harvesting Single Ferroelectric Domain Stressed Nanoparticles For Optical And Ferroic Applications, Gary Cook, J. L. Barnes, S. A. Basun, Dean R. Evans, Ron F. Ziolo, Arturo Ponce, Victor Yu. Reshetnyak, Anatoliy Glushchenko, Partha P. Banerjee

Electrical and Computer Engineering Faculty Publications

We describe techniques to selectively harvest single ferroelectric domain nanoparticles of BaTiO3 as small as 9 nm from a plethora of nanoparticles produced by mechanical grinding. High resolution transmission electron microscopy imaging shows the unidomain atomic structure of the nanoparticles and reveals compressive and tensile surface strains which are attributed to the preservation of ferroelectric behavior in these particles.

We demonstrate the positive benefits of using harvested nanoparticles in disparate liquid crystal systems.

Characterization Of Atmospheric Turbulence Effects Over 149 Km Propagation Path Using Multi-Wavelength Laser Beacons, Mikhail Vorontsov, Gary W. Carhart, Venkata S. Rao Gudimetla, Thomas Weyrauch, Eric Stevenson, Svetlana Lachinova, Leonid A. Beresnev, Jony Jiang Liu, Karl Rehder, Jim F. Riker

Electrical and Computer Engineering Faculty Publications

We describe preliminary results of a set of laser beam propagation experiments performed over a long (149 km) near-horizontal propagation path between Mauna Loa (Hawaii Island) and Haleakala (Island of Maui) mountains in February 2010. The distinctive feature of the experimental campaign referred to here as the Coherent Multi-Beam Atmospheric Transceiver (COMBAT) experiments is that the measurements of the atmospheric-turbulence induced laser beam intensity scintillations at the receiver telescope aperture were obtained simultaneously using three laser sources (laser beacons) with different wavelengths (λ1 = 0.53 μm, λ2 = 1.06 μm, and λ3 = 1.55 μm). The presented experimental results on …

Inductively Coupled Plasma Dry Etching Process On Planar Lightwave Circuit Fabrication., Chuah Khoon Seah

Student Works (2010-2019)

The main objective of this project is to master state-of-the-art techniques and knowledge in silica etching in order to achieve high quality waveguide circuit on Planar Lightwave Circuit devices. Another objective is to optimize the clean room research strength, surface characterization, microscopy techniques and similar semiconductor manufacturing processes.Initially, these processes were conducted with wet etching method that utilized diluted hydrofluoric acid (HF) and buffered oxide etch (BOE). Several problems arising such as mask peel-off, poor sidewall profile and defect waveguide channel during the pattern transfer process due to its’ isotropic nature. Alternatively, dry etching method was conducted via Inductively Coupled …

Development Of Optical Coherence Tomography For Tissue Diagnostics, Panomsak Meemon

Electronic Theses and Dissertations

Microvasculature can be found in almost every part of the human body, including the internal organs. Importantly, abnormal changes in microvasculature are usually related to pathological development of the tissue cells. Monitoring of changes in blood flow properties in microvasculature, therefore, provides useful diagnostic information about pathological conditions in biological tissues as exemplified in glaucoma, diabetes, age related macular degeneration, port wine stains, burn-depth, and potentially skin cancer. However, the capillary network is typically only one cell in wall thickness with 5 to 10 microns in diameter and located in the dermis region of skin. Therefore, a non-invasive flow imaging …

12 Bit Charge Redistribution Digital To Analog Converter For The Residence Time Fluxgate Magnetometer, Miguel Angel Alamillo

Open Access Theses & Dissertations

The continuous advances in CMOS VLSI technology have culminated in high speed, low voltage CMOS digital circuits with gate delays below 50 ps at 1.5 V supply. At the same time, high voltage analog signal processing has fallen behind to the high flexibility and high reliability of DSP. However, the main drawback of DSP is the need for high accuracy low distortion data converters and as a consequence of the persistent efforts of reducing size, cost and power of solid-state components the field of CMOS Mixed-Signal circuit design has become of the utmost importance.

The obvious functionality of data converters …

Optimization Of Inductively Coupled Plasma Dry Etching For Planar Waveguide Fabrication., Lim Weng Hong

Student Works (2010-2019)

Optimization of the Inductively Coupled Plasma (ICP) dry etching process parameters has been carried out. Seven main etching characteristics were considered in order to produce good etching quality. These characteristics are glass etching rates, selectivity of chromium to glass etching rate, channel side wall roughness, channel side wall vertical profile, channel cleanliness, critical dimension and resolution. Several ICP parameters that are affecting the etching characteristic were optimized in this work. These optimised ICP parameters obtained from this work are ICP power (880 W), bias power (45 W), operating chamber pressure (10 mtorr), reactant gas composition, reactant gas flow rate (35sccm …

Characterization Of An Inductively Coupled Plasma Produced In Argon At 13.56 Mhz., Lim Ai Nuan

Student Works (2010-2019)

The electrical and plasma characteristics of radio frequency (13.56 MHz) inductively coupled argon plasma (RF ICP) were studied in this project. On the electrical breakdown properties, the breakdown voltage has a general appearance of Paschen’s curve and the minimum is achieved at 0.1 mbar. After ignition, two modes of discharge exist, namely, the E mode at low RF power and H mode at high RF power. Mode transition that occurs is accompanied by abrupt changes in both electrical and plasma characteristics. Hysteresis is observed in the mode transitions and has a minimum at 0.1 mbar. The resistance reflected into the …

The Development Of Scalable Pump Techniques For Gg Iag Fiber Lasers And Passive Athermalization Techniques For Solid State Laser, William Hageman

Electronic Theses and Dissertations

This dissertation consists of two parts: research pertaining to the development of scalable pump techniques for gain guided index-antiguided fiber lasers and research relating to the development of passive athermalization schemes for solid state lasers. The first section primarily details the development of a side pump scheme that allows for power scaling of gain-guided index anti-guided fibers. While these fibers have been demonstrated in past research, none have used a pump technology capable of pumping with the efficiencies, uniformity, and necessary length to allow for scaling of the fiber lasers to high output powers. The side pumped scheme developed in …