Electrical and Computer Engineering Commons^™

An Analysis Of A Shunt-Peaked Video Amplifier And Feedback Pair Having The Same Edge Response, Bernard J. Regenauer

Electrical and Computer Engineering ETDs

Statement of the problem. It is the purpose of this study (1) to investigate the feasibility of employing a feedback pair instead of a shunt-peaked video amplifier in a typical circuit application; (2) to determine the steady-state gain ratio between a feedback pair and a single shunt-peaked video amplifier having the same edge response (rise time and overshoot) and to analyze the effect of varying either the rise time or overshoot of both circuits upon this ratio; (3) to make a limited study of the steady state gain ratio of a feedback pair and a cascade of two shunt-peaked video …

The Transient Response Of A Distributed Amplifier, Thomas D. Lusk

Electrical and Computer Engineering ETDs

The purpose of this paper is to describe the transient behavior of a simple constant-K distributed amplifier stage. The derivation of the transfer function is carried out using the Laplace Transform for the case where losses in the lines are considered to be zero. The various characteristics of the amplifier response to a unit step function are discussed and the effects of losses and other modifying factors upon the idealized response are evaluated. Finally design procedures are derived which allow the circuit designer to determine the circuit parameters necessary for good transient responses. These procedures are applied to the design …

An Experimental And Theoretical Investigation Of The Characteristics Of A Magnetic Amplifier, Merle H. Wittmeyer

Electrical and Computer Engineering ETDs

Many excellent analyses of magnetic amplifiers have been published. As in every investigation, however, there are many details not explained. The purpose of this investigation was to explain some of the details of magnetic amplifier characteristics.

Servo-Stabilization Of Drift In Wide-Band D-C Amplifiers., Joel M. Simmons Jr.

Electrical and Computer Engineering ETDs

It was the purpose of this study to determine the suitability of a comparator and negative feedback circuit (servo-type) as a general utility method of reducing the end effect (zero-drift) of changing static characteristics of the vacuum tubes and other associated components in wide-band direct-coupled amplifiers. A brief description of the drift servo-stabilization system and its drift reducing characteristics are as follows.

The Design And Construction Of An Electronic D-C Analog Computer, Frederick R. Wagner, William A. Paar

Masters Theses

"To make this project realizable with the funds available and in the time allowed, and to set forth some definite goals, the following objectives were adopted:

1. Design, construct, and place in working order a d-c electronic analog computer capable of solving 4th order linear differential equations with constant coefficients.
2. Include in the design provisions for real time computation, and also fast, repetitive operation.
3. Provide for later expansion of the computer installation.
4. Limit expenditures to $700"--Introduction, page 4.

An Analysis Of A Cathode-Coupled Multivibrator, Fred T. Sinnott

Electrical and Computer Engineering ETDs

The purpose of this study is to develop an analysis for monostable cathode-coupled multivibrators and verify the analysis by experimental results.

An Analysis Of The Monostable Cathode-Coupled Multivibrator, Joseph C. Connell

Electrical and Computer Engineering ETDs

II. PURPOSE OF THESIS

The foregoing comments pointed out the facts that: 1) little has been done to show the similarity between the multivibrator and the RC amplifier with degenerative feedback; 2) the existing treatment of the conditions under which a linear relationship between pulse duration and applied grid voltage will exist does not give results which are in very good agreement with the values used in a practical circuit.

It is the purpose of this study to fill in these gaps by showing that the equations resulting from an analysis of the cathode-coupled multivibrator are, in general, those of …

An Investigation Of The Effect Of Feedback On Amplifier Figure Of Merit, John L. Crone

Electrical and Computer Engineering ETDs

It was the purpose of this investigation to determine the effect of feedback on the figure of merit of (1) the resistance coupled amplifier; (2) the shunt peaked amplifier; and (3) the single tuned amplifier.

Organization And Execution Of A Major Industrial Electrification Project, Robert F. Mccaw

Professional Degree Theses

"All emergencies, especially those created by war, have marshalled the industrial might of nations, among other things. World War II was no exception; in fact, it produced the greatest expansion of industrial facilities in history.

Most all plants in the country underwent some degree of expansion. In certain industries, the experienced workers of existing plants were employed as nuclei for the organization of the gigantic new plants required to produce the arms and equipment necessary to the conduct of a global war.

This thesis pertains to one phase of the design and construction of such an enterprise. This particular phase …

A.C. Circuit Interruption, Palmer L. Anthony Jr.

Masters Theses

"In the last few years the transmission voltages have increased tremendously. Along with the voltage increase came increased load carrying ability for the circuits. The first few links of a new 330 KV transmission system are now under construction in this country. Sweden is already operating a 380 KV line. It is expected to carry a load as high as 850,000 KW on a single circuit.

Interconnection between systems in adjoining areas is a practice to get further operating benefits. The benefits are - reduction of necessary reserve capacity, increased load diversity, and decreasing losses.

Both of these developments bring …

Random Wave Form Generator, Zaboj V. Harvalik

Journal of the Arkansas Academy of Science

No abstract provided.

The Design Of A Closed-Loop Voltage Regulator For A D-C Generator, Ernest P. Longerich

Masters Theses

"The methods of obtaining voltage regulation for a d-c generator are many, and they vary in complexity according to the requirements of the loads being supplied.

A need for zero voltage regulation is not uncommon in power supplies that are used in laboratory work. It is frequently not enough, however, to have a supply whose steady state regulation is zero; the need may also exist for fast transient response to changes in load.

In general, then, the criteria for excellent voltage-versus-load characteristics of a d-c power supply might be stated as follows:

1. It has zero steady state error.
2. It has …

Clipper Amplitude Modulator, Durmuş Öcal

Masters Theses

"An amplitude modulated wave is defined as a wave form in which the amplitude of a sinusoidal signal (carrier) is varied in accordance with a modulating signal whose frequency is much lower than the frequency of the carrier signal. Numerous devices have been found for generating an amplitude modulated wave. In some modulators the amplitude of the carrier is actually varied in accordance with the modulating signal. In other types of modulators the carrier and the modulating signal are simultaneously applied to a nonlinear element or circuit. The output of this non-linear element is a distorted wave containing many frequencies. …

Transfer Function Of The Modified Kramer System, David L. Hillhouse

Masters Theses

"The use of operational mathematics in the solution of engineering problems has grown tremendously in the last two decades, particularly during the last war. This has come about because of the facility with which problems which would be almost impossibly complicated or tedious to solve by classical methods can be solved using operational calculus.

The operational calculus, particularly the Laplace transform method, has become especially useful in the field of servomechanisms and controls. Here the constantly increasing complexity of systems used has resulted in very high order differential equations. The fact that the Laplace transform method makes it possible to …

Analysis Of Magnetic Amplifiers Based On Assumed Analytical Expressions Of B-H Characteristics, Wiley Talley Ruhl

Masters Theses

"In the past 10 years, magnetic amplifiers have received much attention in many different fields of engineering. Although the principles of this amplifier have been known since 1915, it has been forced into the background by the development of the vacuum tube amplifier, the need of better core material and better dry disk rectifiers.

The basic magnetic amplifier, or saturable reactor, is nothing more than an iron core reactance coil whose a-c impedance is controlled by a d-c premagnetization of the core. This d-c premagnetization may be obtained in a number of ways, the simplest of which is a separate …

An Experimental Study Of The Effect Upon The Current Distribution And Radiation Pattern Of Crossbars On Yagi Receiving Antennas, Gerald F. Sinnamon

Masters Theses

"The development and widespread use of radar systems in World War 11, and the post-war television boom, has brought about a large amount of investigation in antenna arrays. One of the types of antennas commonly used on radar systems during the early part of the war, and one which finds wide usage today as a television receiving antenna, is the well known Yagi antenna...

Since television antennas are usually mounted out of doors, the antenna must be made mechanically strong to prevent whipping or twisting due to wind, and to prevent sagging due to icing or to its own weight. …

Design Of A Galvanometer To Be Placed Within A Tubular Antenna For The Purpose Of Measuring Antenna Current Distribution, Ferdinand Henry Mullersman

Masters Theses

"The object of this paper is to design such a galvanometer for application to cylindrical UHF antennas and to discuss the procedure involving its use. The galvanometer will then be placed inside a completely isolated parasitic antenna and the distribution of current along the antenna will be measured"--Introduction, page 5.

A Sine-Wave Frequency Dividing Circuit, Louis L. Fisher

Electrical and Computer Engineering ETDs

The scope of this thesis was to investigate the stability, dividing range and some of the characteristics of a new type of sine-wave frequency divider.

Frequency Modulated Audio Oscillators, James L. Dossey

Electrical and Computer Engineering ETDs

It was therefore the purpose of this study (1) to evaluate existing sub-channel oscillator circuits seeking first, to improve them; (2) to uncover new ideas, and to incorporate them into a frequency modulated audio oscillator that would satisfactorily fulfill the required specifications; (3) once such a circuit was found, to obtain such refinements as simplicity of alignment, interchangeability of tubes, better frequency stability by utilizing proper mechanical design, and smaller, cheaper parameters without sacrificing performance.

An Experimental Investigation Of The Te01 Electromagnetic Fields In Ridge Waveguide, George A. Arnot Jr

Electrical and Computer Engineering ETDs

The aim of this thesis is to arrive at the field distribution of the ridge waveguide for the TE₀₁ mode, either mathematically or experimentally, the latter proving to be the case. Under the heading of Theoretical Considerations the difficulties involved in obtaining a mathematical solution to the problem are presented. The experimental results then follow and in the Conclusions a comparison is made of the results obtained by other writers and the author's data.

Problems In Theatre Lighting And Pre-Selective Elctronic Lighting Control, Hasan Orhan Aker

Masters Theses

"Until the recent years, because of the lack in technical know-how of play producers and on the other hand the limited knowledge of the engineers about stage technique, all the advantages provided by efficient stage lighting could not be exploited. Especially, the different problems encountered from the point of view of lighting control, could not be solved for a long time.

It has been proven from theatres built lately, that the stage lighting designs made without a thorough study of the various stage conditions and requirements lead to a tremendous increase in cost and also inefficient operation of the whole …

Series Capacitors, Emcet Bilgeer

Masters Theses

"Static capacitors as an element of transmission and distribution circuits first appeared in the form of shunt capacitors. These shunt capacitors were primarily used in power factor correction. They can be regarded as a load in the circuit which draws a loading current. This loading current fleeing through the reactive line produces a voltage rise, thus reducing the voltage drop between sending and receiving ends. This phenomenon helps the voltage control of the feeder as well as power factor correction. The disadvantage of the shunt capacitor is its inflexibility. The shunt capacitor is connected across the line; hence the voltage …

A Survey Of Single Ended Tuned Grid Tuned Plate Class C Power Amplifiers, Chandrakant D. Gandhi

Masters Theses

"The analysis of tuned grid-tuned plate Class C power amplifiers has been treated by many authors in many ways. The methods differ in accuracy and in time required to obtain the end results. A survey of most important of these methods was taken up by the author of this thesis with an aim towards studying their accuracies, advantages and disadvantages. A general survey of this type of analysis has not been found in the literature. In this survey only the most important phases of the tuned grid-tuned plate single ended Class C power amplifiers are discussed.

This survey has been …

Investigation Of Vacuum Tubes As Four Terminal Networks, Vasil Uzunoglu

Masters Theses

"This thesis was undertaken with the aim of consolidating the most important work that has been done in the field of equivalent vacuum tube circuits which has been found to be highly disassociated.

The author of this thesis feels that this thesis is the most complete consolidation of information on equivalent vacuum tube circuits"--Introduction, page 3.

Study Of Relay Behaviour Under System Oscillations And Out Of Step Conditions, Emil D. Grigoriadis

Masters Theses

"The recent developments in harnessing electrical power have opened a new field in the improvement and betterment of the existing types of relays and the development of new types. Thus about 1930 the manufacturers introduced the high speed circuit breaker with operating times of the order of 8 cycles and the engineers awoke to the possibilities of high speed or one-cycle relays.

Many developments took place since that time which gave us the improved forms of Instantaneous Overcurrent Protective schemes, the Distance Relay Protection, the Carrier Current Protection and many others. Later, because of the war time problems of increased …

A Study Of Radio Frequency Converters And Mixers, James J. Skiles

Masters Theses

"This thesis will present a detailed discussion of the principles of frequency conversion and the problems attendant to the design of converter stages. The topic of harmonic conversion has been singled out for a more extended treatment than is now available in the literature. This topic is the subject of the experimental investigation portion of this thesis. Harmonic conversion has applications in U-H-F receivers as well as in "Double Superheterodyne Receivers".

The discussion given to the frequency converter in the first section of this thesis will be without regard to any applications. General theory will be stressed, and most of …

Economic Analysis Of Secondary Distribution Networks, Charles F. Cromer

Masters Theses

"In the early history of commercial electricity in heavy load density areas, the d.c. Edison Network was developed extensively. As far as reliability is concerned it is exceeded by no system. At the present time it has been developed to the extent of automatic and non-automatic converters, motor-generator sets, booster sets and storage battery reserve capacity.

This type of network is fed from several substations in the area at utilization voltage.

As load densities have increased, the large amounts of copper required, the cost of substation sites and large rotating conversion equipment have made the expansion of the d.c. Network …

Design Of A Steam Power Plant To Be Erected In Mudanya, Turkey, Vahram Ogretmenoglu

Masters Theses

"The power plant, the design of which is submitted herewith, is to be erected in Turkey, at the center of the town of Kestik, in the district of Mudanya along the shores of the Marmora Sea. Mudanya is the harbor of the state of Brusa, and like most of the big cities, it is entirely electrified. However, electrification in Turkey has begun in the late twenty's; consequently, it has not yet been possible to bring electricity to the numerous small towns and villages. Several big projects have been undertaken for purposes of rural electrification, one of them being the erection …

Analysis Of Conductor Vibration, Robert H. Nau

Electrical and Computer Engineering Faculty Research & Creative Works

Considerable attention has been given to conductor vibration of suspended transmission lines during the past 25 years. Even so, the engineers of the public utilities feel that they have only started to get a solution to the vibration problems. Extensive research programs are being conducted at the present time by manufacturers of conductor cable and ground wires and by numerous public utilities themselves.

Aeolian vibrations are the chief concern because they occur whenever a steady wind, of from one mile per hour to hurricane velocity, blows across the suspended line. Thus, millions of flexures, however small or large in amplitude, …

A Theoretical And Experimental Analysis Of Delay Circuits, Shuh-Tuh Tsai

Electrical and Computer Engineering ETDs

A delay circuit is a circuit which produces rectangular pulses of specified duration.

A rectangular pulse consists of three parts: first, a sudden rise of voltage; second, remaining a constant voltage during a certain time interval; and third, a sudden drop of voltage to its original value.

If the sudden rise of voltage at t, is produced by a certain sudden action of a circuit previous to the pulse circuit, the sudden drop of voltage at t₂ can cause another circuit to produce a sudden action. Thus, the second action is produced by the first action at a time …