Electrical and Computer Engineering Commons^™

Machine Learning Based Automation Of Pcb Pdn Design And Optimization, Haran Manoharan

Doctoral Dissertations

The rapid increase in power density and stringent power-integrity requirements in modern System-on-Chip (SoC) platforms have made Power Delivery Network (PDN) design an increasingly complex, multi-stage challenge. Critical decisions must be made both during pre-layout planning, such as stackup configuration, power-plane geometry, and early decoupling capacitor (decap) budgeting, and during post-layout refinements. Traditional heuristic and evolutionary optimization techniques struggle with scalability, require extensive manual iteration, leading to long runtimes and limited adaptability across varying board configurations. To address these challenges, this work proposes a unified reinforcement-learning-driven framework for automated PDN synthesis and decap optimization that spans both pre-layout and post-layout …

Incremental Cluster Validity Indices And Their Role In Interpreting Lifelong Learning Systems, Niklas Max Melton

Doctoral Dissertations

Clustering and supervised learning are often treated as distinct paradigms, yet both rely on structure in feature space. This dissertation investigates the relationship between cluster validity indices (CVIs) and supervised learning in real-time and lifelong learning settings where data arrive incrementally and cannot be revisited. Across four studies, it develops methods for online cluster validation, uses supervised learning to improve their interpretability, and applies these ideas to evaluating performance degradation in continual learning.

The first study extends incremental cluster validity indices (iCVIs), enabling widely used validation metrics to operate in streaming environments. Experiments on synthetic and real-world datasets show systematic …

Towards Robust Autonomous Systems: Handling Multi-Modal Uncertainties In Gps-Denied Environments, Vivya Kalidindi

Doctoral Dissertations

This dissertation focuses on designing a robust and uncertainty-aware framework for autonomous systems operating in GPS-denied environments, such as indoor infrastructures, underground tunnels, and lunar surfaces. The proposed framework addresses the challenges posed by multi-modal uncertainties, including sensor noise, distributional shifts under adverse conditions, and conflicting decision-making preferences. These challenges compromise the reliability and adaptability of autonomous platforms. To overcome these challenges, the proposed framework adopts a layered architecture that integrates advanced methodologies across the sensing, perception, and decision-making layers. At the sensing layer, an Edge-Kalman Filter combined with a density ratio-based update mechanism is employed to reduce aleatoric uncertainty …

Encryption With Synchronized Chaos Using Fabricated Cobalt Ferrite Memristors, Kiran Sai Seetala

Doctoral Dissertations

No abstract provided.

Multiscale Materials Characterization And In-Situ Process Monitoring In Additive Manufacturing Via Non-Contact Optical Thermometry Techniques, Rifat-E-Nur Hossain

Doctoral Dissertations

While additive manufacturing (AM) is experiencing rapid growth, its development is uneven across different branches. Some areas are still emerging, while even the more established branches are still facing ongoing challenges that require further development. Regardless of their development stage, both emerging and mature AM require process monitoring and part characterization. Process monitoring helps to achieve more control over the process and build a self-adaptive system, while characterization of printed parts speeds up process optimization and ensures required quality. Together, process monitoring and build characterization will transform AM into a more dependable and commercially viable technique. Build surface temperature is …

Real-Time Prediction Of Dynamical Systems Using A Hybrid Analog Computer: Network Traffic Modeling, Majd Zuhair Tahat

Doctoral Dissertations

As the number of online users grows exponentially, the number and severity of cyber threats escalate, urgently requiring advancements in real-time network modeling and response. Swiftly predicting and analyzing network traffic is crucial for effective network monitoring and control, preventing cyber breaches, and maintaining healthy network functionality. This research presents a novel approach to real-time modeling based on analyzing evolving properties and patterns in a dynamical network system using a hybrid analog-digital computer. An analog computer was utilized as a co-processor to compute differential equations that model the Transmission Control Protocol (TCP) window size. A comparative analysis was conducted between …

Lifelong Machine Learning With Adaptive Resonance Theory, Sasha Petrenko

Doctoral Dissertations

"This publication option dissertation is composed of three papers concerning the study of the problem lifelong machine learning with Adaptive Resonance Theory (ART) algorithms. Lifelong learning (L2) is a challenging machine learning paradigm that both encompasses and formalizes the fields of continual learning and incremental learning. The field is concerned with the mitigation of the phenomenon of catastrophic forgetting whereby learning agents that are faced with incrementally novel information deleteriously overwrite previous knowledge if that learning process is not regularized to counteract this consequence. ART algorithms solve this stability-plasticity dilemma by optimally assigning learning to categories or instantiating new knowledge …

Systematic Esd Analysis And Modeling For Electronic Device, Zhekun Peng

Doctoral Dissertations

Systematic ESD analysis provides good pre-compliance to ESD robustness evaluation on the electronic device from device level to component/system level to on-chip level. The whole process involves corona discharge on display, system level ESD analysis on PCB for race condition and transient response and 3D IC package impact to on-die ESD.

ESD to the display cover glass can damage touchscreen traces by sparkless corona discharges on the glass surface. A non-linear time dependent transmission-line model is proposed to model corona streamer propagation in terms of the coupling current and propagation speed. Results are highly promising to model the corona discharge …

Metal-Organic Thin Film Coated On Optical Fiber, Nahideh Salehifar

Doctoral Dissertations

This dissertation explores the development of metal-organic framework (MOF)-based optical fiber sensors for detecting volatile organic compounds (VOCs) at low concentrations (parts-per-billion to parts-per-million). In the first part of the study, theoretical calculations were performed using effective medium approximation (EMA) models, including Lorentz–Lorentz, Maxwell–Garnett, and Bruggeman equations, to predict the refractive index changes of MOFs upon gas adsorption. These models were applied to MOFs such as ZIF-7, ZIF-8, ZIF-90, MIL-101(Cr), and HKUST-1 to evaluate their potential for gas sensing.

In the second part of the dissertation, experimental work was conducted to validate the theoretical predictions. MOF-coated optical fibers were fabricated …

Measurement Method And Applications Of Transfer Function In Rf Desensitization Problem, Xiangrui Su

Doctoral Dissertations

Radio frequency (RF) desensitization issues comprise two components: noise radiation sources and the transfer function from noise sources to the victim antenna. RFI is a critical challenge in modern electronic systems, particularly in densely packed environments. This work presents a comprehensive study of RFI, addressing key aspects through three novel contributions. First, a transfer function measurement method is developed for compact metallic enclosures. This method provides a precise characterization of the electromagnetic (EM) environment within confined spaces, enabling accurate identification of interference pathways. Second, an EM emission management analysis framework is proposed, leveraging transfer functions to quantify and mitigate interference …

Advancements In Signal Processing And Image Reconstruction For Active Microwave Thermographic Measurements, Logan Martin Wilcox

Doctoral Dissertations

Active microwave thermography, or AMT, is a coupled electromagnetic-thermographic nondestructive testing and evaluation technique. AMT has found success in a variety of inspection needs in the aerospace, space, and infrastructure fields due to its unique type of thermal excitation. During an AMT inspection, a specimen is exposed to microwave energy from a radiating source (i.e., an antenna). This exposure to microwave energy results in dielectric/magnetic heating, which causes an increase in temperature and potential defect indications to manifest on an inspection surface (which is measured via an infrared camera). Due to the use of an antenna, there is a spatially …

Selected Topics In Blockchain-Aided Iot Inference, Yiming Jiang

Doctoral Dissertations

"Blockchain has recently been considered in the Internet of Things (IoT) to secure data exchanges and storage across various engineering applications. This newly emerging blockchain-aided IoT (BIoT) network has been applied to a great deal of security-related applications. However, the BIoT still has the vulnerability that can be exploited by attackers, potentially impairing the performance of BIoT applications. Despite this, research addressing the vulnerability has been limited. This work presents four studies aimed at addressing critical gaps in current BIoT research.

The first study introduces a Time-Restricted Double-Spending Attack (TR-DSA) model for Proof-of-Work (PoW)-based blockchains, where the adversary only conducts …

New Topologies For High Voltage Gain Dc-Dc Power Electronic Converters – Theoretical Analysis And Experimental Validation, Saeed Habibi

Doctoral Dissertations

"This dissertation is focused on developing and analyzing new high voltage gain DC-DC power electronic converters. The proposed converters in this dissertation are suitable candidates for connecting low voltage sources such as photovoltaic (PV) panels or fuel cell (FC) stacks to a DC microgrid or DC link of an inverter. The proposed converters provide desired characteristics such as high voltage gain at a low or medium duty cycle values, low voltage stress on power semiconductors, and continuous input current. Initially, the research introduces three novel converter topologies: First, two quadratic converters based on the combination of a three-winding coupled inductor …

Power Supply Induced Jitter Analysis In High-Speed Drivers, Yifan Ding

Doctoral Dissertations

The Input/Output Buffer Information Specification (IBIS) model faces challenges in accurately simulating power-supply-induced jitter (PSIJ), particularly under nonlinear and time-varying power noise conditions with pre-driver stages. This work introduces advancements in IBIS model modification algorithms to enhance PSIJ simulation accuracy for high-speed drivers.

First, a correction coefficient-based approach was developed to adjust switching coefficients K_pu and K_pd using pre-driver DC jitter sensitivity, significantly improving model robustness under DC and AC power noise. However, its effectiveness diminished under large noise amplitudes due to coefficient shape dominance.

To address this, a simplified algorithm bypassed correction coefficient, directly correlating switching transitions with jitter …

In Situ High Temperature Fiber-Optic Raman Sensor For Industrial Applications, Bohong Zhang

Doctoral Dissertations

"Continuous casting in steel production uses specially developed oxyfluoride glasses (mold fluxes) to lubricate a mold and control the solidification of the steel in the mold. The composition of the flux impacts properties, including basicity, viscosity, and crystallization rate, all of which affect the stability of the casting process and the quality of the solidified steel. However, mold fluxes interact with steel during the casting process, resulting in flux chemistry changes that must be considered in the flux design. Currently, the chemical composition of mold flux must be determined by extracting flux samples from the mold during casting and then …

Control And Optimization Of Energy Storage System In Power Distribution System, Waqas Ur Rehman

Doctoral Dissertations

"The widespread adoption of electric vehicles (EVs) and transportation electrification is encumbered by two chief barriers: i) the limited driving range of EVs in the market today and ii) inadequate fast-charging infrastructure for long-distance trips. Extreme fast charging (XFC) technology can recharge EVs in less than 10 minutes for 200 miles range. Firstly, a novel robust optimization-based mixed integer linear programming model is proposed to size a battery energy storage system (BESS) and PV system in an XFCS. In this part, it is assumed that the sizing and location of the XFCS are known. Secondly, the aforesaid assumption is relaxed, …

Non-Linearity Modeling And Quantifications For Practical Rf Interference Control, Shengxuan Xia

Doctoral Dissertations

"Radio frequency (RF) interference can degrade the receiving sensitivity of antennas (desense problem). It is essential to model the nonlinearity as it is the root-cause of the unwanted frequency components. Understanding the electromagnetic (EM) coupling or radiated emissions is also important.

Nonlinearity causes modulation-involved desense problems, and it consists of two categories: upconvertion of the baseband noise by the transmitting (TX) signal, and the passive intermodulation (PIM) of the transmitting signal itself. The upconvertion caused desense can be modeled and analyzed with the dipole-moment based coupling framework. PIM has been identified as another nonlinear distortion mechanism, specifically in the metallic …

Applications Of Computational Intelligence And Data Fusion Techniques For Biomedical Images, Anand Krishnadas Nambisan

Doctoral Dissertations

"The realm of melanoma diagnosis has been significantly advanced by deep learning (DL) techniques, yet the current approaches are not without limitations, including missed diagnoses and the challenge of interpreting these "black box" models. The research is comprised of three studies, each contributing uniquely towards advancing melanoma detection accuracy and interpretability. The first study focuses on improving the detection of specific dermoscopic structures through a deep learning-based segmentation approach, while the second study builds upon this by employing a fusion technique that combines traditional image features with advanced deep learning models. This method significantly improves melanoma detection, particularly in recall …

Modeling And Analysis Methods For Esd And Emi Problems, Xin Yan

Doctoral Dissertations

"Electrostatic discharge (ESD) failures and Electromagnetic interference (EMI) problems are becoming more critical in electronic devices and large systems. In this work, four studies are presented to model and analyze ESD and EMI problems.

First, a simplified physical-based model for deep-snapback transient voltage suppressors (TVS) is developed. While based on physics, the number of parameters and components is minimized. Results show that the proposed model captures the most important behaviors of the TVS response using a limited number of parameters, allowing the model to be tuned relatively easily using data obtained only from package-level transient and quasi-static measurements. Second, a …

Semiconductor Physics Based Signal Integrity Analysis For 3d Ic, Ze Sun

Doctoral Dissertations

"Three-dimensional integrated circuits (3DICs) are becoming increasingly popular in high-speed electrical systems. 3DICs are made by stacking multiple dies vertically and connecting them with through-silicon vias (TSVs). In this dissertation, three studies were carried out to model the performance of 3DICs in extreme working conditions and the signal integrity (SI) performance of 3DICs.

First, an in-house Monte Carlo particle simulator was developed to characterize extreme working conditions (ESD/EMP) for ICs at the microscopic level instead of the macroscopic level. The ability of the simulator was demonstrated by modeling a voltage regulator diode under forward and reverse bias. The diode simulation …

Modeling And Analysis Of Dc-Dc Converters For Power Distribution Networks Design, Junho Joo

Doctoral Dissertations

"Accurate modeling of power distribution networks (PDN) including voltage regulator module (VRM) is critical for high-performance digital systems including low- to high-power applications such as laptops and mobile platforms. As a consolidated end-to-end power source, PDN can be divided into several parts: the VRM to regulate the external voltage source, printed circuit board (PCB) PDN, package PDN, and on-chip PDN. A transient current drawn from the on-die circuitry will produce an instantaneous voltage drop at the bump. The time domain behavior of such a drop and the subsequent recovery is called voltage droop which is strongly associated with the VRM …

Adversarial Transferability And Generalization In Robust Deep Learning, Tao Wu

Doctoral Dissertations

Despite its remarkable achievements across a multitude of benchmark tasks, deep learning (DL) models exhibit significant fragility to adversarial examples, i.e., subtle modifications applied to inputs during testing yet effective in misleading DL models. These meticulously crafted perturbations possess the remarkable property of transferability: an adversarial example that effectively fools one model often retains its effectiveness against another model, even if the two models were trained independently. This research delves into the characteristics influencing the transferability of adversarial examples from three distinct and complementary perspectives: data, model, and optimization. Firstly, from the data perspective, we propose a new method of …

Deep Reinforcement Learning Based Strategies For Inverter Dominated Microgrids, Oroghene Oboreh-Snapps

Doctoral Dissertations

The integration of inverter-based distributed generators (IBDGs) in modern power systems has ushered in a new era of renewable energy utilization, prompting the rise of Microgrid (MG) architectures. Nevertheless, as IBDG penetration increases, a host of challenges surface. Foremost among these challenges are issues related to frequency stability stemming from the inherent lack of inertia in IBDGs, and inaccurate sharing of reactive and active power, particularly evident in parallel IBDG networks with mismatched feeder impedance. This research presents novel solutions to these challenges by adopting deep reinforcement learning (DRL), specifically, the twin delayed deep deterministic policy gradient (TD3) algorithm, to …

Accurate And Time Efficient Signal Integrity And Power Integrity Modeling Of High-Speed Digital Systems, Chaofeng Li

Doctoral Dissertations

"Signal integrity (SI) and power integrity (PI) play an important role in the modern high-speed digital system design, which are closely related to the printed circuit board (PCB) dielectric material property, the PCB interconnect performance, and the power delivery network (PDN) on PCB. Generally, the full-wave simulation is used to accurately analyze and evaluate the designed PCB. But full-wave simulation is not a good option for the complex PCB structure with high aspect ratio, for example, PCB vias, and PDN, which will require significant computing time and storage resources. Equivalent circuit models have been developed to efficiently predict the electrical …

Modeling And Analysis Of The Selective Lightning Strike Phenomenon At Locations In A Chemical Manufacturing Plant, Terver Maor

Doctoral Dissertations

This research was motivated by the overly simplified claims, from a previous study, that attempted to explain the cause of the reportedly repeated lightning strikes at certain locations in the chemical manufacturing plant. The findings, without any model, claimed that the electronic monitoring and control devices’ fire damage occurred, due to the raised electrical ground potential during lightning strikes. It proceeded that the raised electrical ground potential caused a power flow reversal, which exceeded the ratings of the affected electronic control modules, damaging them. This claim is inconsistent with published research work in the failure mechanisms of industrial control systems, …

Fiber Optic Sensors For Liquid Identifications, Wassana Naku

Doctoral Dissertations

"The fiber optic Fabry-Perot interferometer (FPI) is a widely utilized sensing configuration, offering numerous advantages over conventional electronic sensors, including high accuracy, distributed sensing capabilities, immunity to electromagnetic interference, and compact size. In this study, we propose a remarkably simple fiber optic-tip sensor system combined with machine learning techniques for the identification of pure and volatile organic liquids (VOLs).

A liquid droplet forms an extrinsic FPI (EFPI), with its effective reflectance being a function of the droplet's length. As the droplet evaporates, its length decreases. We conducted immersion tests using optical fiber tip sensors and monitored the time-transient responses of …

Design, Modeling And Analysis Of An Ac-Ac Dual Active Bridge Converter, Kartikeya Jayadurga Prasad Veeramraju

Doctoral Dissertations

"The Solid-State Transformer (SST) is gaining attention as an alternative to conventional iron-core transformers in the power electronic community. The power industry's increasing demands for smaller size, higher efficiency, and greater energy density have made the SST an attractive option. Among various power electronic converter topologies, the Dual Active Bridge (DAB) has become popular for its bidirectional power flow capability and galvanic isolation, primarily in the DC application space. Advancements in semiconductor technologies have introduced new bidirectional switches, opening avenues for novel SST topologies. This research investigates the application of the DAB as a single-stage SST and focuses on advancements …

Introduction Of A Variable Inductance Transformer For The Design Of Resonant Power Converters, Angshuman Sharma

Doctoral Dissertations

"Magnetic integration is a hot topic in power electronics that concerns the use of a transformer's leakage and magnetizing inductances purposefully in isolated power electronic converters, thereby giving the opportunity to save the cost and footprint of any additional inductor. This is of prime interest, especially in CLLLC resonant converters which require up to three inductors. For a complete integration of these inductances, the concept of a variable inductance transformer (VIT) is introduced in this thesis. A VIT is an adaptive magnetic structure that facilitates an easy adjustment of both magnetizing and leakage inductances to meet their desired values. However, …

Geometry-Aware Methodology For Coupling Mechanism Analysis And Radiation Mechanism Analysis, Xu Wang

Doctoral Dissertations

"Due to the wide-band spectrum of digital signals, a variety of noise generators, including microprocessors, liquid crystal displays, digital microphones, high-speed traces, and double-data-rate memory modules, are found in consumer electronics products. Noise generated by digital circuits can couple to the antennas and degrade their sensitivity. Additionally, it also couples to metallic housings or heatsinks and produces a significant amount of emission. In this research, methodologies are presented to analyze the coupling and radiation mechanism in electronic devices.

To investigate the coupling between the distributive geometries in the radio frequency interference (RFI) problem, a mesh-dependent partition-based coupling mechanism analysis method …

Advanced Topologies Of High Step-Up Dc-Dc Converters For Renewable Energy Applications, Ramin Rahimi

Doctoral Dissertations

"This research is focused on developing several advanced topologies of high step-up DC-DC converters to connect low-voltage renewable energy (RE) sources, such as photovoltaic (PV) panels and fuel cells (FCs), into a high-voltage DC bus in renewable energy applications. The proposed converters are based on the combinations of various voltage-boosting (VB) techniques, including interleaved and quadratic structures, switched-capacitor (SC)-based voltage multiplier (VM) cells, and magnetically coupled inductor (CI) and built-in-transformer (BIT). The proposed converters offer outstanding features, including high voltage gain with low or medium duty cycle, a small number of components, low current and voltage stresses on the components, …