Computer Engineering Commons^™

Neurofuzzy Robust Backstepping Based Mppt Control For Photovoltaic System, Kamran Ali, Laiq Khan, Qudrat Khan, Shafaat Ullah, Naghmash Ali

Turkish Journal of Electrical Engineering and Computer Sciences

Linear maximum power point tracking (MPPT) techniques are unable to achieve the desired performance and efficiency under wide variation in atmospheric conditions (temperature and irradiance) and consequently the maximum power point (MPP). Hence, the design and implementation of a nonlinear MPPT controller is essential to address the problems associated with the variations of the MPP. In this research article, a new nonlinear robust backstepping-based MPPT control technique is proposed for a standalone PV array connected to a dynamic load, and its performance comparison with existing backstepping, integral backstepping and conventional proportional integral derivative (PID) and perturb and observe (P&O) based …

Performance Improvement Of The Shunt Active Power Filter Using A Novel Adaptivefiltering Approach, Abderrezzaq Zoghbi, Daoud Berkani

Turkish Journal of Electrical Engineering and Computer Sciences

This paper introduces an efficient control approach to enhance harmonics mitigation performance of the shunt active power filter (SAPF). This approach is based on adaptive filters favored by their built-in automatic parameters adaptation capability. The proposed filter, which uses a variable leaky least mean square (VLLMS) adaptation, is applied with a modified instantaneous power PQ theory. This enhances its dynamic performance over the use of conventional time-invariant filters, and overcomes its limitations in the presence of nonsinusoidal voltage conditions. The studied SAPF model is simulated in MATLAB/SIMULINK with combinations of nonlinear and unbalanced loads. Simulation results indicate a significant improvement …

Robust Model Reference Adaptive Pi Controller Based Sliding Mode Control Forthree-Phase Grid Connected Photovoltaic Inverter, Mojtaba Moeti, Mehdi Asadi

Turkish Journal of Electrical Engineering and Computer Sciences

In this paper, the design of a new robust model reference adaptive PI (MRAC-PI) current controller is proposed for a two-stage grid connected photovoltaic (PV) inverter. Perturb & observe (P&O) algorithm is implemented in the boost part in order to extract the maximum power from the PV array. Firstly, the current dynamics with considering the system uncertainties are written in dq frame and are simplified by employing a decoupling system. Then, the MRAC-PI controller is designed based on a sliding mode control (SMC) to improve the robustness of the controller under system uncertainties. The parameters of PI controller are tuned …

A Counter Based Approach For Reducer Placement With Augmented Hadoop Rackawareness, Mir Wajahat Hussain, K Hemant Reddy, Diptendu Sinha Roy

Turkish Journal of Electrical Engineering and Computer Sciences

As the data-driven paradigm for intelligent systems design is gaining prominence, performance requirements have become very stringent, leading to numerous fine-tuned versions of Hadoop and its MapReduce programming model. However, very few researchers have investigated the effect of intelligent reducer placement on Hadoop's performance. This paper delves into this much ignored reducer placement phase for improving Hadoop's performance and proposes to spawn reduce phase of Hadoop tasks in an asynchronous fashion across nodes in a Hadoop cluster. The main contributions of this paper are: (i) to track when map phase of tasks are completed, (ii) to count the number of …

A Two-Stage Hair Region Localization Method For Guided Laser Hair Removal, Murat Avşar, İmam Şami̇l Yeti̇k

Turkish Journal of Electrical Engineering and Computer Sciences

Removal of hair using laser is a widely used method, where our goal is to permanently remove hair by using laser to cause heat in order to thermally damage the hair follicle. However, currently available laser hair removal systems affect the outer skin layers besides hair follicles. This is a disadvantage of classical methods with major health risks. We propose a method to overcome these health risks by guiding the laser beam only to automatically localized hair regions. This study aims to develop an automated feature-based hair region localization method as an integral part of the proposed hair removal system …

Energy Considerations In Blockchain-Enabled Applications, Cesar Enrique Castellon Escobar

UNF Graduate Theses and Dissertations

Blockchain-powered smart systems deployed in different industrial applications promise operational efficiencies and improved yields, while mitigating significant cybersecurity risks pertaining to the main application. Associated tradeoffs between availability and security arise at implementation, however, triggered by the additional resources (e.g., memory, computation) required by each blockchain-enabled host. This thesis applies an energy-reducing algorithmic engineering technique for Merkle Tree root and Proof of Work calculations, two principal elements of blockchain computations, as a means to preserve the promised security benefits but with less compromise to system availability. Using pyRAPL, a python library to measure computational energy, we experiment with both the …

A Surrogate Weather Generator For Estimating Natural Gas Design Day Conditions, David J. Kaftan, George Corliss, Richard J. Povinelli, Ronald H. Brown

Electrical and Computer Engineering Faculty Research and Publications

Natural gas customers rely upon utilities to provide gas for heating in the coldest parts of winter. Heating capacity is expensive, so utilities and end users (represented by commissions) must agree on the coldest day on which a utility is expected to meet demand. The return period of such a day is long relative to the amount of weather data that are typically available. This paper develops a weather resampling method called the Surrogate Weather Resampler, which creates a large dataset to support analysis of extremely infrequent events. While most current methods for generating weather data are based on simulation, …

Cybersecurity Leaders: Knowledge Driving Human Capital Development, Sharon L. Burton

Publications

Cybersecurity leaders must be able to use critical reading and thinking skills, exercise judgment when policies are not distinct and precise, and have the knowledge, skills, and abilities to tailor technical and planning data to diverse customers’ levels of understanding. Ninety-three percent of cybersecurity leaders do not report directly to the chief operating officer. While status differences influence interactions amid groups, attackers are smarter. With the aim of protecting organizations and reducing risk, knowledge about security must increase. Understanding voids are costly and increased breach chances are imminent. Burning questions exist. What are needed technological learnings for cybersecurity leaders to …

Integration Of Robotic And Electro-Pneumatic Systems Using Advanced Control And Communication Schemes, Chinmay Kondekar

Dissertations, Master's Theses and Master's Reports

Modern industrial automation systems are designed by interconnecting various subsystems which work together to perform a process. The thesis project aims to integrate fragmented subsystems into a flexible and reconfigurable system through advanced communication protocols and perform a process to demonstrate the effectiveness of interconnected systems.

The system consists of three six-axis robots, one electro-pneumatic robot, and two conveyors connected using EthernetIP communication and hardwired connections. The interconnected system works together to perform machining of a workpiece using advanced control methods of CAD to robot path generation, central control through a PLC, and process control through HMI.

Standardized programming blocks …

Human-Robot Interaction For Assistive Robotics, Jiawei Li

Dissertations

This dissertation presents an in-depth study of human-robot interaction (HRI) withapplication to assistive robotics. In various studies, dexterous in-hand manipulation is included, assistive robots for Sit-To-stand (STS) assistance along with the human intention estimation. In Chapter 1, the background and issues of HRI are explicitly discussed. In Chapter 2, the literature review introduces the recent state-of-the-art research on HRI, such as physical Human-Robot Interaction (HRI), robot STS assistance, dexterous in hand manipulation and human intention estimation. In Chapter 3, various models and control algorithms are described in detail. Chapter 4 introduces the research equipment. Chapter 5 presents innovative theories and …

Performance Optimization Of Big Data Computing Workflows For Batch And Stream Data Processing In Multi-Clouds, Huiyan Cao

Dissertations

Workflow techniques have been widely used as a major computing solution in many science domains. With the rapid deployment of cloud infrastructures around the globe and the economic benefits of cloud-based computing and storage services, an increasing number of scientific workflows have migrated or are in active transition to clouds. As the scale of scientific applications continues to grow, it is now common to deploy various data- and network-intensive computing workflows such as serial computing workflows, MapReduce/Spark-based workflows, and Storm-based stream data processing workflows in multi-cloud environments, where inter-cloud data transfer oftentimes plays a significant role in both workflow performance …

Semantic, Integrated Keyword Search Over Structured And Loosely Structured Databases, Xinge Lu

Dissertations

Keyword search has been seen in recent years as an attractive way for querying data with some form of structure. Indeed, it allows simple users to extract information from databases without mastering a complex structured query language and without having knowledge of the schema of the data. It also allows for integrated search of heterogeneous data sources. However, as keyword queries are ambiguous and not expressive enough, keyword search cannot scale satisfactorily on big datasets and the answers are, in general, of low accuracy. Therefore, flat keyword search alone cannot efficiently return high quality results on large data with structure. …

Sistem Keamanan Ganda Sepeda Motor Dengan Fingerprint Dan Gprs Berbasis Arduino Untuk Peningkatan Keamanan, Bartholomeus Danar, Masduki Zakarijah

Elinvo (Electronics, Informatics, and Vocational Education)

Tujuan pembuatan Tugas Akhir ini adalah: (1) merancang fingerprint dan gprs pada sistem pengaman sepeda motor, (2) mengimplementasi fingerprint dan gprs pada sistem pengaman sepeda motor, (3) mengetahui unjuk kerja fingerprint dan gprs pada sistem pengaman sepeda motor. Komponen utama yang digunakan adalah Arduino Mega sebagai pusat olah data , fingerprint sebagai keamanan utama, gprs sebagai kemanan kedua. dan kode numerik sebagai penulisan password serta mensetting sistem. Langkah Pembuatan Sitem Keamanan Ganda Sepeda Motor Berbasis Arduino Untuk Peningkatan Keamanan ini adalah (1) Perancangan Perangkat Keras: pertama Pembuatan Skematik Sistem , kedua Pembuatan Layout PCB, ketiga Pembuatan Desain 3D, terakhir …

Pendeteksi Bola Pada Robot Penjaga Gawang Menggunakan Metode Hough Circle, Alwi Widi Pradana, Dessy Irmawati

Elinvo (Electronics, Informatics, and Vocational Education)

Robot penjaga gawang bertugas untuk dapat menghadang bola berwarna oranye memasuki gawang. Robot tersebut harus mampu mendeteksi bola dengan akurat untuk menentukan pergerakan robot selanjutnya. Artikel ini mendeskrepsikan pengembangan robot penjaga gawang yang mampu mendeteksi warna dan bentuk boladengan metode hough circle menggunakan emgucv. Metode pengembangan yang dilakukan merujuk pada modifikasi ADDIE pada pengembangan robot speak bola. Hasil dari pengembangan ini adalah lapangan robot dan robot penjaga gawang. Hasil unjuk kerja menunjukkan pendeteksian bola memiliki presentase rerata sebesar 80%, sedangkan kemampuan menghadang bola sebesar 90%. Penerapan metode hough circle terdiri atas beberapa proses yaitu: (1) mencari ciri warna bola, langkah …

Penerapan Iot Untuk Sistem Pemantauan Lampu Penerangan Jalan Umum, Adam Adam, Muharnis Muharnis, Ariadi Ariadi, Jefri Lianda

Elinvo (Electronics, Informatics, and Vocational Education)

Penerangan jalan umum (PJU) digunakan untuk menerangi jalan, sehingga pengguna jalan mendukung kenyamanan dan keselamatan dimalam hari. Terdapat keterbatasan sistem pemeriksaan dan pelaporan kerusakaan lampu PJU. Artikel ini membahas penerapan teknologi Internet of Things (IoT) untuk memantau gangguan kerusakan pada lampu PJU. Metode yang digunakan dalam pengembangan sistem pemantauan tersebut yaitu, kajian literatur, analisis kebutuhan, perancangan, pembuatan dan pengujian. Sistem ini dilengkapi dengan sensor ZMPT101B, ACS 712, dan Modul WiFi ESP 8266-01. Sensor ZMPT101B digunakan untuk mengukur nilai tegangan PLN, sedangkan sensor ACS 712 merupakan sensor yang digunakan untuk mengukur arus pada lampu jalan. ESP8266-01 merupakan modul wifi yang dapat …

Human Activity Recognition Using Wearable Sensors: A Deep Learning Approach, Jialun Xue

Theses

In the past decades, Human Activity Recognition (HAR) grabbed considerable research attentions from a wide range of pattern recognition and human–computer interaction researchers due to its prominent applications such as smart home health care. The wealth of information requires efficient classification and analysis methods. Deep learning represents a promising technique for large-scale data analytics. There are various ways of using different sensors for human activity recognition in a smartly controlled environment. Among them, physical human activity recognition through wearable sensors provides valuable information about an individual’s degree of functional ability and lifestyle. There is abundant research that works upon real …

Treated Hfo2 Based Rram Devices With Ru, Tan, Tin As Top Electrode For In-Memory Computing Hardware, Yuvraj Dineshkumar Patel

Theses

The scalability and power efficiency of the conventional CMOS technology is steadily coming to a halt due to increasing problems and challenges in fabrication technology. Many non-volatile memory devices have emerged recently to meet the scaling challenges. Memory devices such as RRAMs or ReRAM (Resistive Random-Access Memory) have proved to be a promising candidate for analog in memory computing applications related to inference and learning in artificial intelligence. A RRAM cell has a MIM (Metal insulator metal) structure that exhibits reversible resistive switching on application of positive or negative voltage. But detailed studies on the power consumption, repeatability and retention …

The Assessments Of Internet-Based Technology Use By University Academic Members, Mohammed Alghamdi

BAU Journal - Science and Technology

Social networking applications (SNAs), as technologies that rely on internet infrastructure, are widely used as platforms for user interaction, content creation and social communication. However, in recent years, SNAs have been used in the context of teaching and learning, and this aspect, as well as others, has attracted research attention. Limited research has investigated the motivations and barriers to teaching with SNAs in higher education, and so this study sought to examine the purposes, motivations and barriers associated with SNA use in education among academic members at Albaha University, Saudi Arabia. A quantitative research design involving a sample of academic …

Significant Contribution Of Mobile Apps To The Development Of Tourism In Uzbekistan, Alimjon Dadamuhamedov Irgashevich

The Light of Islam

Recently, Uzbekistan has taken comprehensive measures to develop tourism as one of the strategic sectors that contribute to the rapid development of regions, increase incomes and living standards of the population, as well as increase investment attractiveness. Modern information technologies make a signifcant contribution to the development of pilgrimage tourism. Advertising of online travel services in pilgrimage tourism currently does not allow you to automate the work of a travel Agency without creating an effective website. This article is devoted to the analysis of Internet technologies aimed at improving the tourism industry. The practical signifcance of the article lies in …

An Integrated Three-Flow Approach For Front-End Service Composition, Lim Mei Ting

Student Works (2020-2029)

End-User Service Composition (EUSC) aims to enable end-user programmers who are not professional developers, develop applications by composing or aggregating existing web services. Despite the effort, studies have shown that end-user programmers are not able to deal with the technical complexities involved in EUSC. One way to deal with this issue is Front-End Service Composition (FESC), which allows end-user programmers to compose web services at the presentation layer of an application by configuring User Interface (UI) widgets that represent the back-end web services. However, apart from there not being enough studies on FESC, end-user programmers also experience a number of …

Three Emerging Innovative Technologies Required For Cyber Operations To Execute Commander’S Intent At Machine Speed, Andrew Stewart

Military Cyber Affairs

Decision advantage for the DoD and Combined Cyber Operations results from the secure, seamless, and rapid maneuver of data and information. In the DoD’s 2018 Artificial Intelligence Strategy, the DoD recognized that it must, “put in place key building blocks and platforms to scale and democratize access to AI. This includes creating a common foundation of shared data, reusable tools, frameworks and standards, and cloud and edge services.”[1] More than ever, integrated, adaptive cyber operations provide the means of maneuver for data to enable DoD’s decision advantage-based goals. To support this vision, the integrated implementation three innovative cyber technologies …

Assessing Impacts Of 5th Generation (5g) Cellular Telecommunications On Internet Of Things (Iot) Deployments, Michael Love, Marwan Jamal

Military Cyber Affairs

The Internet of Things (IoT) is emerging as a primary enabler of the transformation to digital business services in today’s economy. At the same time, 5^th Generation (5G) cellular transport technology is emerging as a viable means to support IoT data requirements. Although 5G is still in its infancy, DoD leaders need to understand the impacts that 5G will have on IoT projects as there are several challenges involved with integrating 5G into IoT. In order to achieve the maximum benefits of high bandwidth, low latency and superior performance, an entirely new grid of cell sites and access units …

Recent Advances And Machine Learning Techniques On Sickle Cell Disease, Noorh H. Alharbi, Rana O. Bameer, Shahad S. Geddan, Hajar M. Alharbi

Future Computing and Informatics Journal

Sickle cell disease is a severe hereditary disease caused by an abnormality of the red blood cells. The current therapeutic decision-making process applied to sickle cell disease includes monitoring a patient’s symptoms and complications and then adjusting the treatment accordingly. This process is time-consuming, which might result in serious consequences for patients’ lives and could lead to irreversible disease complications. Artificial intelligence, specifically machine learning, is a powerful technique that has been used to support medical decisions. This paper aims to review the recently developed machine learning models designed to interpret medical data regarding sickle cell disease. To propose an …

A Supporting Tool For Requirements Prioritization Process In Agile Software Development, Ramdan Mowad, Khaled Abdelazim Muhammad, Essam Elfakharany

Future Computing and Informatics Journal

Requirements engineering is a crucial phase of software engineering, and requirements prioritization is an essential stage of requirements engineering particularly in agile software development. Requirements prioritization goals at eliciting which requirements of software need to be covered in a particular release. The key point is which requirement will be selected in the next iteration and which one will be delayed to other iterations for minimizing risk during development and meeting stakeholders’ needs. There are many existing techniques for requirement prioritization, but most of these techniques do not cover continuous growth, change of requirements, and requirements dependencies. The prioritization techniques need …

Twitter Analysis Based On Damage Detection And Geoparsing For Event Mapping Management, Yasmeen Ali, Khaled Bahnasy, Adel El-Mahdy

Future Computing and Informatics Journal

Background: Early event detection, monitor, and response can significantly decrease the impact of disasters. Lately, the usage of social media for detecting events has displayed hopeful results. Objectives: for event detection and mapping; the tweets will locate and monitor them on a map. This new approach uses grouped geoparsing then scoring for each tweet based on three spatial indicators. Method/Approach: Our approach uses a geoparsing technique to match a location in tweets to geographic locations of multiple-events tweets in Egypt country, administrative subdivision. Thus, additional geographic information acquired from the tweet itself to detect the actual locations that …

Models And Methods Of Designing Human-Machine Interaction-Oriented Interfaces, Ozod Radjabov, Shakhrillo Bobokulov, Behruz Boboqulov, Hojiyev Sunatullo

Bulletin of TUIT: Management and Communication Technologies

Formalization approaches of user interface design (UID) in conjunction with model driven techniques aim to improve the usability in terms of conformity to standards or style guides and to leverage code generation of interactive software systems, so that various UI platforms for web, desktop or mobile Applications are supported. Because large parts of the UI are described platform independent instead of platform dependent implementations, re-usability of the UI concept is also improved. However, UI formalization requires the usage of a formal UI description language and a higher level of abstractness compared to concrete UI code. These languages need to be …

Use Of Image Processing Algorithms For Mine Originating Waste Grain Size Determination, Sebastian Iwaszenko

Journal of Sustainable Mining

The utilization of mineral wastes from the mining industry is one of most challenging phases in the raw materials life cycle. In many countries, there are piles of mineral waste materials that date back to the previous century. There is also a constant stream of accompanying mineral matter excavated during everyday mine operation. This stream of waste matter is particularly notable for deep coal mining. Grain size composition of waste mineral matter is one of most important characteristics of coal originating waste material. This paper presents the use of image analysis for the determination of grain size composition of mineral …

A Bibliographic Survey On Detection Of Covid-19 Patients Using Various Sensors In The Field Of Iot, Rutuja Patil, Akshay Sharma, Divya Bhatia, Mugdha Kulkarni, Yashika Patl

Library Philosophy and Practice (e-journal)

Due to a pandemic situation arising from the past few decades and the covid -19 patients are increasing at the rapid rate. Looking in the near future an IOT model is build which can be useful for people in coming years and allows rapid testing and efficient testing methodologies using various sensors such as Temperature, Respiration, RFID etc which takes various parameters. The study focuses around 412 scientific documents such as Journals, articles, book chapters and Patents in various papers. These documents are extracted from the scopus databases after querying with the keywords related to covid patients and IOT. The …

The Ftc And Ai Governance: A Regulatory Proposal, Michael Spiro

Seattle Journal of Technology, Environmental, & Innovation Law

No abstract provided.

Efficient End-To-End Autonomous Driving, Hesham Eraqi

Theses and Dissertations

Steering a car through traffic is a complex task that is difficult to cast into algorithms. Therefore, researchers turn to train artificial neural networks from front-facing camera data stream along with the associated steering angles. Nevertheless, most existing solutions consider only the visual camera frames as input, thus ignoring the temporal relationship between frames. In this work, we propose a Convolution Long Short-Term Memory Recurrent Neural Network (C-LSTM), which is end-to-end trainable, to learn both visual and dynamic temporal dependencies of driving. Additionally, We introduce posing the steering angle regression problem as classification while imposing a spatial relationship between the …