Civil and Environmental Engineering Commons^™

Revitalizing The Moment Distribution Method: A Fast And Exact Analysis Of Multibay, Multi-Story Frames., Jackson Kong, Simon Ho Fai Wong

Faculty of Science & Technology (THEi)

The conventional moment distribution method is revitalized with a new approach which requires only one-cycle of balance and carry-over and no iteration. For a continuous beam, the method begins by assuming the value of the balancing moment, say x, at the first joint. By invoking the moment equilibrium condition successively from the first towards the last joints, balancing and carry-over moments at other joints can be determined in terms of the unknown x without iteration. By means of moment equilibrium of the last joint, the unknown x can be solved exactly, regardless of the number of spans, and the final …

Enhancing The Crumb Rubber Modified Asphalt's Storage Stability Through The Control Of Its Internal Network Structure, Mohyeldin Ragab, Magdy Abdelrahman

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The current research investigated the effect of the internal network structure developed in the crumb rubber modified asphalt (CRMA) on its storage stability. The authors investigated the influence of asphalt-crumb rubber modifier (CRM) interaction parameters (interaction time, interaction speed, and interaction temperature) on the development of the internal network structure in CRMA. The authors found that the existence of three dimensional (3D) network structures in the CRMA enhanced its storage stability. Fourier Transform Infrared (FTIR) Spectroscopy was utilized to determine the nature of CRM components responsible for the development of 3D network structure in the liquid phase of CRMA. This …

Inspire Newsletter Spring 2018, Missouri University Of Science And Technology. Inspire - University Transportation Center

INSPIRE Newsletters

No abstract provided.

Evaluating The Application Of Microbial Induced Calcite Precipitation Technique To Stabilize Expansive Soils, Bhaskar Chittoori, Sikha Neupane

Civil Engineering Faculty Publications and Presentations

Expansive soils, also known as swell-shrink soils have been a problem for civil infrastructures including roads and foundations from ancient times. The use of chemical additives such as cement and lime to stabilize expansive soils is a common practice among geotechnical engineers, especially for lightly loaded structures. However, several occurrences of subgrade failures have been observed after stabilizing with chemical additives. Hence, engineers are in search of sustainable stabilization alternatives. Microbial Induced Calcite Precipitation (MICP) is gaining attention as an environmentally friendly soil improvement technique. Several researchers have successfully tested its feasibility in mitigating liquefaction-induced problems in sandy soils. In …

Integrated Analysis Of The Value Of Wetland Services In Coastal Adaptation; Methodology And Case Study Of Hampton-Seabrook Estuary, New Hampshire, Paul Kirshen, Semra Aytur, David M. Burdick, Diane Foster, Tom Lippmann, Ellen Douglas, Sydney Nick, Chris Watson

Jackson Estuarine Laboratory

The present impacts from coastal storms and high tides grow significantly over time due to SLR even over the relatively short period to 2060. Hydrodynamic model simulations of storm surge with and without sea level rise scenarios show that although flooding and inundation increases with increasing subtidal forcing and higher sea level, dissipation of the tide and storm surge in the estuary channel somewhat limits the maximum inundation that might otherwise be expected in the back marsh areas. The estuary is dominated by high marsh, which lies high in the intertidal zone and by 2060 it will convert to mostly …

Mechanistic Insight Into The Degradation Of Nitrosamines Via Aqueous-Phase Uv Photolysis Or A Uv-Based Advanced Oxidation Process: Quantum Mechanical Calculations, Daisuke Minakata, Erica Coscarelli

Department of Civil, Environmental, and Geospatial Engineering Publications

Nitrosamines are a group of carcinogenic chemicals that are present in aquatic environments that result from byproducts of industrial processes and disinfection products. As indirect and direct potable reuse increase, the presence of trace nitrosamines presents challenges to water infrastructures that incorporate effluent from wastewater treatment. Ultraviolet (UV) photolysis or UV-based advanced oxidation processes that produce highly reactive hydroxyl radicals are promising technologies to remove nitrosamines from water. However, complex reaction mechanisms involving radicals limit our understandings of the elementary reaction pathways embedded in the overall reactions identified experimentally. In this study, we perform quantum mechanical calculations to identify the …

Effect Of Polypropylene Fiber Reinforcement On The Consolidation, Swell And Shrinkage Behavior Of Lime Blended Expansive Soil, Arif Ali Baig Moghal, Bhaskar C.S. Chittoori, B. Munwar Basha

Civil Engineering Faculty Publications and Presentations

In this article, synthetic fibers in the presence of lime stabilization are proposed as an alternative to overcome the issues related to shrink-swell distress in expansive soils. Two types of synthetic fibers, Fiber Cast® (FC) and Fiber Mesh® (FM), were studied by conducting one dimensional fixed ring Oedometer swell-consolidation and bar linear shrinkage tests. Three dosages (0.2, 0.4 and 0.6% percent by weight of soil) and two lengths of the fibers (6 and 12 mm) were evaluated with and without lime treatments. The results indicated that FC fibers had better swell restricting performance in the absence of lime treatment, while …

Rethinking Zoning For People: Utilizing The Concept Of The Village, Kevin Leyden, Lorraine D'Arcy

Other

In this chapter, we propose it is time to re-think and re-imagine how we approach zoning. This is especially true for suburban developments. Today, especially in the United States, zoning in suburban areas is being used to segregate and separate the component parts of our communities into distinct zones which are spread out geographically and in most cases require the daily use of an automobile. The negative consequences of this form of development for health, community and the environment are discussed. Using a study of neighborhoods in Dublin, Ireland and its suburbs we examine how professionals and the public view …

A Bioreactor For Conditioning Tissue Engineered Heart Valves, Claire Brougham, Francisco Almeida, Fergal J O'Brien

Other resources

No abstract provided.

Introducing A New Cement Hydration And Microstructure Model, Niall Holmes

Articles

This paper presents a new cement hydration model (HYDCEM) to predict the microstructure evolution of hydrating tricalcium silicate (C3S). The model is written in MATLAB and employs the continuum approach and integrated particle kinetics relationships to show the change in C3S and the growth of Calcium Silicate Hydrate (C-S-H) and Calcium Hydroxide (CH) in the pore space over time. Cement hydration is a highly complex process. While hydration models should never completely remove experimental analysis, they are an aid to better understand cement hydration and microstructure development by providing a method to analyse a large number of pastes with different …

A Rupture Limit Equation For Pre-Loaded Composite Plates, William P. Schonberg

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Fiber-reinforced polymer composites offer inherent advantages over traditional metallic materials in a number of different ways; however, these materials are also highly susceptible to impact damage. In this paper, we explore the response of FRP (fiber reinforced polymer) composites under impact conditions that could result in their rupture or catastrophic failure. The work performed was aimed at developing a general, data-driven equation for initially-stressed, flat, composite plates that would differentiate between impact conditions that would result in only a hole or crack and those which would cause catastrophic plate failure or rupture. If this equation were to be subsequently shown …

Failure Of The Alexander Dam Embankment And Reconstruction Using Drainage Mitigation On Kauai, Hawaii, 1930-1932, Kerry D. Cato, J. David Rogers

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Alexander Dam is a hydraulic fill earth dam and the second-highest embankment dam in Hawaii, having been built in 1929-1932 on the south side of the Hawaiian island of Kauai to provide irrigation for McBryde Sugar Company Ltd. It was constructed across Wahiawa Stream mauka (Hawaiian for "stream that comes from the mountains," literally "toward the mountains"), upstream of Kalaheo, to store 800 million gallons (5 million m3) of water to irrigate sugarcane fields. The embankment dam was intended to have a maximum height of 125 ft (38 m), a crest length of 620 ft (189 m), and a maximum …

Partitioning Of Pcbs From Air To Clothing Materials In A Danish Apartment, Glenn Morrison, H. V. Andersen, L. Gunnarsen, D. Varol, E. Uhde, B. Kolarik

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Polychlorinated biphenyl (PCB) contamination of buildings continues to pose an exposure threat, even decades after their application in the form of calks and other building materials. In this research, we investigate the ability of clothing to sorb PCBs from contaminated air and thereby influence exposure. The equilibrium concentration of PCB-28 and PCB-52 was quantified for nine used clothing fabrics exposed for 56 days to air in a Danish apartment contaminated with PCBs. Fabric materials included pure materials such as cotton and polyester, or blends of polyester, cotton, viscose/rayon, and/or elastane. Air concentrations were fairly stable over the experimental period, with …

Inspire Newsletter Fall 2018, Missouri University Of Science And Technology. Inspire - University Transportation Center

INSPIRE Newsletters

No abstract provided.

Exploring High-Resolution Data Obtained From Asc/3 Controller Of Intersection Se Division St & Se 122nd Ave, Portland, Oregon, Naowar Al-Abbas

Civil and Environmental Engineering Master's Project Reports

High-resolution data obtained from ASC/3 controllers can be used to create a variety of performance measures, helping engineers and professionals in monitoring intersection performance, identifying issues, and making proper improvements. These measures concern the intersection quality of the progression, capacity, and non-vehicular operations (e.g. pedestrian crossings). In this report, we explored high-resolution data obtained from the intersection of SE Division Street and 122nd Avenue. This intersection had some safety concerns as it is considered one of most dangerous intersections in Portland, Oregon. Thus, the first variable we examined from the data was pedestrian wait time when a cross request is …

Color Removal And Treatment Of Dye And Sugar Waste Water Using Low Cost Adsorbents, Saisantosh Vamshi Harsha Madiraju

ETD Archive

This study was undertaken to determine the treatment of wastewater from dye and sugar industry for removal of color. This specific treatment consists of adsorption using low cost adsorbents and micro filtration using whatman-41 micro filters. Considerations of this treatment process is to take the samples using batch adsorption and avoid coagulation with further dilution. Numerous runs were made with the ideal waste samples prepared in the laboratory. As a first step in the study different dyes were considered using different concentrations of sugar wastewater. Samples were treated with three different low-cost adsorbents. These treated samples using low cost adsorbents …

Civil Engineering Surrounds You, Claire Anderer-Armstrong

Undergraduate Research Posters 2018

Academic engineering departments are regularly asked to conduct tours of their laboratories to prospective CSU students. For the Civil & Environmental Engineering department, the tours typically take place in the Driving Simulation laboratory, which houses an RS-600 driving simulator. The purpose of this project was to develop a driving scenario that highlights various aspects of civil engineering. The programmed scenario will be used to conduct future tours.

Cee 433: Water Technology & Policy Syllabus, University Of Illinois At Urbana-Champaign, Ashlynn Stillwell

All ECSTATIC Materials

This document is the syllabus for CEE 433: Water Technology & Policy, by instructor Ashlynn S. Stillwell at the University of Illinois at Urbana-Champaign. The course is an elective class, open to upper-level undergraduate and graduate students.

Jeopardy - Water Price, Ecnomic Cost, Economic Value, Rabi Gyawali, Ali Mirchi, David Watkins, Jr.

All ECSTATIC Materials

It's Jeopardy! Test your knowledge of water prices, water cost, it's economic value, full value, and more. Information developed from a companion lecture and two readings:

1. Brett Walton. (2010). The Price of Water: A Comparison of Water Rates, Usage in 30 U.S. Cities. April 26. Circle of Blue WaterNews. Available at: https://www.circleofblue.org/2010/world/the-price-of-water-a-comparison-of-water-rates-usage-in-30-u-s-cities/.
2. Peter Rogers, Radhika de Silva, Ramesh Bhatia. (2002) Water is an economic good: How to use prices to promote equity, efficiency, and sustainability, Water Policy, Volume 4, Issue 1, 2002, Pages 1-17, https://doi.org/10.1016/S1366-7017(02)00004-1.

How many Jeopardy points can you earn?

Milwaukee Wet Weather Flow Management System Planning, David Watkins

All ECSTATIC Materials

Many older cities across the United States rely on combined sewers to convey both stormwater runoff and sanitary sewage. Combined sewer overflows (CSOs), containing untreated sewage, occur during extreme wet weather, when the capacity of these combined sewer systems is exceeded. Across the U.S., CSOs pose a serious threat to water quality in thousands of lake, river, and coastal ecosystems. In addition to harming the natural environment, they may be a threat to human health and have adverse economic consequences (e.g., beach closings, reduced aesthetics, tourism impacts).

In this assignment, students role-play engineering consultants tasked with developing a cost-effective plan …

Plastic Hinge Relocation In Reinforced Concrete Beams Using Cu-Al-Mn Sma Bars, S. Pareek, Maged Youssef, Mohamed E. Meshaly, Y. Araki

Civil and Environmental Engineering Publications

costs. The use of Ni-Ti superelastic shape memory alloy (SMA) constitutes a considerable portion of this research. Cu-Al-Mn superelastic SMA has been recently developed to eliminate the high cost of Ni-Ti SMA, as well as, to have better machining characteristics. This paper explores the use of Cu-Al-Mn SMA bars to relocate the plastic hinge of concrete beams through an experimental–numerical study. The cyclic performance of four beams was examined. The first was reinforced with steel bars and the remaining three were reinforced with combination of SMA and steel bars. The location of the SMA bars was different for each of …

Assessment Of The Flexural Behavior Of Reinforced Concrete Beams Strengthened With Concrete Jackets, M. Monir A. Alhadid, Maged Youssef

Civil and Environmental Engineering Publications

Analysis of continuous jacketed Reinforced Concrete (RC) beams requires accounting for the nonlinear behavior of the interface and the materials as well as redistribution of moments. This kind of analysis is complex and require an advanced level of knowledge and experience to perform. Engineers need simplified yet robust tools to practically predict the actual behavior of jacketed RC beams. In the current practice, slip is neglected in the analysis and monolithic behavior is assumed for the jacketed section, which result in higher estimates of stiffness and/or capacity. This paper provides a simplified method to analyze continuous jacketed RC beams taking …

Seismic Fragility Assessment Of Superelastic Shape Memory Alloy Reinforced Concrete Shear Walls, Emad A. Abraik, Maged A. Youssef

Civil and Environmental Engineering Publications

Mitigation of seismic damage can be achieved through self-centering techniques. One of the potential techniques involves the use of Superelastic Shape Memory Alloy (SE-SMA) bars in Reinforced Concrete (RC) structures. This study explores the use of such bars in the plastic-hinge regions of RC walls. The seismic performance and vulnerability of SE‑SMA RC walls of ten- and twenty-story buildings are analytically assessed using fragility curves. The maximum inter-story drift, residual drift, and fragility are evaluated using multi strip analysis. The results clearly demonstrate the superior seismic performance of SE-SMA RC walls as compared to steel RC walls.

Seismic Performance Of Modular Steel Frames Equipped With Shape Memory Alloy Braces, Papia Sultana, Maged A. Youssef

Civil and Environmental Engineering Publications

The demand for modular steel buildings (MSBs) has increased because of the improved quality, fast on-site installation, and lower cost of construction. Steel braced frames are usually utilized to form the lateral load resisting system of MSBs. During earthquakes, the seismic energy is dissipated through yielding of the components of the braced frames, which results in residual drifts. Excessive residual drifts complicate the repair of damaged structures or render them irreparable. Researchers have investigated the use of superelastic shape memory alloys (SMAs) in steel structures to reduce the seismic residual deformations. This study explores the potential of using SMA braces …

Addressing Clay Mineralogy Effects On Performance Of Chemically Stabilized Expansive Soils Subjected To Seasonal Wetting And Drying, Bhaskar C.S. Chittoori, Anand J. Puppala, Aravind Pedarla

Civil Engineering Faculty Publications and Presentations

Premature failures in chemically stabilized expansive soils cause millions of dollars in maintenance and repair costs. One of the reasons for these failures is the inability of existing stabilization design guidelines to consider the complex interactions between clay minerals and the stabilizers. It is vital to understand these complex interactions, as they are responsible for the strength improvement and swell/shrink reduction in these soils, in turn affecting the overall health of the infrastructure. Hence, this research study examined the longevity of chemically stabilized expansive soils subjected to wetting/drying conditions with a major focus on clay mineralogy. Eight different natural soils …

Unified Approach To Sustainability, Resiliency And Risk Assessments, Thomas Robbins, Bhaskar Chittoori, Amit Gajurel, Robert Hamilton

Civil Engineering Faculty Publications and Presentations

Generally, researchers consider sustainability and resiliency aspects of infrastructure projects independently, without considering the relationship that exists between them. Unified approaches that combine sustainability, resiliency, and analyze risk are very minimal. This paper proposes a unified approach to assessing sustainability, resiliency, and risk for infrastructure via evaluating the performance of a tailings dam under various earthquake magnitudes. A tailings dam is typically in operation for many years, which means they may have a direct impact on the local environment, society, and economy. Due to the extended life of the dam, the probability of a major event occurring that could negatively …

Energising Dairy Decisions, John Upton, Philip Shine, Michael Breen, Michael D. Murphy

Publications

A new tool developed by Teagasc researchers easily and quickly allows dairy farmers to see their energy usage and evaluate how renewable sources could decrease energy costs.

Color Removal From Combined Dye And Fruit Nectar Wastewater Using Adsorption And Microfiltration, Oluwatobiloba A. Akinwande

ETD Archive

Pollution of the waterways is a great challenge of the 21st century. Textile effluents contain compounds which have the capacity to cause more harm when ingested. There are many dye removal technologies like coagulation, photo oxidation which help to remove color from dye wastewater. The use of adsorption to remove color from dye wastewater has been used for many centuries. Activated carbon can efficiently remove color from dye wastewater but it is very expensive and so different researches have been conducted to get the adsorption capacity of different forms of adsorbents. These adsorbents can be gotten from agricultural waste, biomass, …

Factors Affecting Minimum Dissolved Oxygen Concentration In Streams, Chistopher Robert Huhnke

ETD Archive

Modeling water quality has been shown to be a useful tool in strategizing water quality management. Dissolved oxygen (DO) has one of the largest impacts on water quality compared to other parameters. The purpose of the dissertation research is to generate a regression equation model, using the US EPA QUAL2K model as the base, to determine different factors affecting minimum dissolved oxygen concentrations in streams, to determine the critical distance for the minimum dissolved oxygen concentration, and the magnitude of impact of each parameter. Based on regression analysis, the factors affecting minimum DO in river water are effluent biochemical oxygen …

Adsorption And Microfiltration Processes To Treat Dye And Coffee Wastewater., Abhiram Siva Prasad Pamula

ETD Archive

Wastewater from coffee processing industry creates high biological and chemical oxygen demand in the surface water. In addition to coffee wastewater from coffee industry, dyes from textile industry enter surface water affecting water quality in terms of transmissivity of light. Adsorption is an economical wastewater treatment process to remove color from dye and coffee wastewater. In the current thesis, adsorption using low-cost adsorbents like peanut hull and onion peel are used to treat combined dye and coffee wastewater. Three representative dyes including acid black 48, disperse yellow 3, crystal violet certified with processed coffee is used in preparing batch adsorption …