Civil and Environmental Engineering Commons^™

Numerical Simulations Of The Hall–Petch Relationship In Aluminium Using Gradient-Enhanced Plasticity Model, Yooseob Song, Jaeheum Yeon, Byoungjoon Na

Civil Engineering Faculty Publications

+e Hall-Petch relation in aluminium is discussed based on the strain gradient plasticity framework. +e thermodynamically consistent gradient-enhanced flow rules for bulk and grain boundaries are developed using the concepts of thermal activation energy and dislocation interaction mechanisms. It is assumed that the thermodynamic microstresses for bulk and grain boundaries have dissipative and energetic contributions, and in turn, both dissipative and energetic material length scale parameters are existent. Accordingly, two-dimensional finite element simulations are performed to analyse characteristics of the Hall–Petch strengthening and the Hall–Petch constants. +e proposed flow rules for the grain boundary are validated using the existing experimental …

Diffusion And Uniformity Of Recycled Asphalt In Pavements, Baoshan Huang

Abbett Distinguished Seminar Series

Asphalt pavements covers over 93 percent of the paved roads in the United States. The use of recycled asphalt into pavement maintenance and construction has been a common practice. However the lack of understanding of the interaction between recycled and virgin asphalt poses a change on the efficient use of recycled asphalt, and often causes pavement premature failures. The present study addressed some fundamental aspects associated with the beneficial use of recycled asphalt into asphalt paving mixtures: 1) how much recycled asphalt can be mobilized into a uniform asphalt coating in the mixture? and 2) will the mobilized old asphalt …

Simulation Training And Route Optimization For Bridge Inspection, Sushil Louis

INSPIRE Archived Webinars

Since the 1970s, simulation training has developed opera­tional trainers for a variety of complex systems from pilot flight simulations to cultural awareness training simulations. When connected to the real world, such simulation training interfaces can drive real vehicles and systems. We have been building a Simulation Training And Control System (STACS) for autonomous bridge inspection that uses a simulated world to train inspectors to control a heterogeneous group of robots. The objective is that, once trained, inspectors can use the same STACS interface used in training to control multiple real robots simultaneously during a bridge inspection task. We first built …

2019 Fall Engr333 Seminar Presentation, Ivy Chipinda, Andrew Huston, Adam Marquardt, Lillie Spackman

ENGR 333

File for student presentation, given by students in the Fall 2019 class of ENGR333.

Static Analysis Of Circular Plates Under Mechanical Loads, Harpreet Lalia

Publications and Research

In this research statics analysis of circular plates is performed using SolidWorks.

Circular plates with different material properties, thickness to radius ratios, and boundary conditions under mechanical loads are modeled and analyzed in SolidWorks.

The results are obtained for deflections of circular plates under uniform and point loads.

A three-dimensional (3D) model of circular plates is first created in SolidWorks. Then the material properties, mechanical loads and boundary conditions are defined for the plate.

It is found deflection of plates is depended on magnitude of mechanical loads, geometrical parameters, boundary conditions and material properties. Responses of SolidWorks for deflections of …

Energy & Carbon Neutral Nyc, Evan Banks, Elena Zimareva, Elena Malysheva

Publications and Research

In 2016, the world's leading countries signed the Paris Agreement which focused on reducing anthropogenic climate change on the planet. On May 2019, New York State and New York City declared its own ambitious goals aimed at decarbonizing the city and restricting the state’s energy use to relying completely on renewables.

Some of these goals specifically target infrastructure in the city since estimates cite buildings as accounting for nearly 70% of New York’s energy use. The main law of New York’s Climate Policy, Local Law 97, requires all buildings over 25,000 sq ft to reduce their CO2 footprint by 40% …

Static Analysis Of Structural Members, Amani Calderon, Alexis Villalona, Farhad Alinaghizadeh

Publications and Research

This research is devoted to statics analysis of structural members under mechanical loads. Static analysis of beams under uniform transverse mechanical loads is presented. The beams are supported by simply supported boundary condition at both sides. The equilibrium equation of the beams is obtained and solved using analytical method and numerical method. The numerical method employed in this work is generalized differential quadrature (GDQ) method. The type of differential quadrature method used for numerical solution is the polynomial-based GDQ method. The differential equation is discretized into algebraic equations based on the GDQ technique. The algebraic equations are then solved to …

Green Roof System Integrated Soil Methods, Jude R. Vallon, Ivan L. Guzman

Publications and Research

Large metropolitan areas like NYC are seeking to integrate sustainability into retrofitting buildings for the development of green infrastructure. Among the many environmental issues of urbanization, the UHI (urban heat island) effect and storm water runoff are of particular interest when it comes building structures. Individual buildings can contribute towards mitigating these effects with implementation of vegetative rooftops, i.e. Green Roofs. Commercial buildings are currently receiving government incentives and new constructions are required to include green roof installations. However, if existing buildings are considering the addition of a green roof on an existing roof, they have to factor in the …

Modeling The Effects Of Distribution System Topology On Water Quality, Chun-Ying Chao

McKelvey School of Engineering Graduate Student Theses & Dissertations

Inadequate treatment of drinking water causes the formation of disinfection by-products and the regrowth of harmful microbial species. Various studies have addressed the problem of water quality monitoring, but very few have employed topological analysis, a valuable mathematical tool widely applied in biological, business, and social research. This thesis examines the relationship between the topological properties of water distribution systems and water-quality models. In particular, the research proposes a novel framework for mapping network topological attributes to water-quality models. This research adopts topological metrics to assess the accuracy of the predictions of chlorine concentrations in dead ends. It examines four …

Optimizing On-Street Parking Supply With Analytical Models, Chawalit Tipagornwong

Dissertations and Theses

Commercial vehicles are crucial for the urban economy, but they generate negative impacts as well. This leads to restrictions such as a reduction in the number of loading zones. The result is that commercial drivers spend a significant amount of time searching for available loading zones. To avoid searching for parking, some commercial drivers double park, which causes traffic congestion. Therefore, the number of loading zones should be set properly. Since a curb is allocated between both loading zones and parking spaces, both parking types have to be considered. Many on-street parking management strategies have been implemented, including pricing meter …

A New Synthesized Microalloys Steel Ods Of High Amplitude Ultrasonically Irradiation, Marzuki Silalahi, Hanif Abdurrahman Wicaksana, Ferhat Aziz, Syahfandi Ahda, Mohamad Riza Iskandar

Makara Journal of Technology

Micropowders of oxide-dispersion-strengthened (ODS) steel have been synthesized using the ultrasonic irradiation method with variations in amplitude. The ultrasonic irradiation process is performed for 50 h at a frequency of 20 kHz with 40%, 50%, and 60% amplitudes in toluene solution. The formation of Fe-Cr microalloys in the preparation of Fe- 15Cr-0.5Y2O3 powder was analyzed using SEM-EDS, X-ray diffraction (XRD), and TEM-EDS. The percentage of Fe- Cr phase mass fraction of ODS steel micropowder formed during ultrasonic irradiation with 40%:50%:60% amplitude was 12.2%:34.1%:22.1%, with 25.67:77.02:38.51 nm crystallite size. The crystallite size at 50% amplitude was the largest, and the diffusion …

Comprehensive Inspection On The Experimental Ferritic Stainless Steel By Means Of Transmission Electron Microscopy And Neutron Diffraction Techniques, Parikin Parikin, Mohammad Dani, Riza Iskandar, Aziz Khan Jahja, Andon Insani, Joachim Mayer

Makara Journal of Technology

The field of physical metallurgy is one of the primary beacons that guide alloy developments for multipurpose materials such as the in-core structure materials for pressure vessel components and heat exchangers. The surface microstructure of new ferritic steel with significant local constituent materials was characterized by high resolution powder neutron diffractometer (HRPD) and transmission electron microscope (TEM), combined with the energy dispersive X-ray spectroscopy (EDX). The alloy contains73% Fe, 24% Cr, 2% Si, 0.8% Mn, and 0.1% Ni, in %wt. The charge materials were melted by the casting techniques. The neutron diffractograms obtained shows five dominant diffraction peaks at (110), …

Study On Antibacterial Of Chitosan/Hydroxyapatite Doped Magnesium Composite As A Material For Bone Graft Applications, Andromeda Dwi Laksono, Teodoro A. Amatosa, Jr., Hilda Pebrianti Octaviana Sitorus, Wentika Putri Kusuma Asih, Sulistijono Sulistijono

Makara Journal of Technology

Hydroxyapatite (HAp) is one of the constituent minerals of bone and teeth, that has been widely used for synthesizing bone graft. Due to the limitation on properties of the hydroxyapatite, it is doping with Magnesium (HAp-Mg). The addition of Chitosan (Chi) was expected to improve the antibacterial properties of HAp-Mg. The present research aims to study the influence of Chitosan with 0, 5, 15, and 25 wt% addition on biocompatibility properties of Chi/HAp-Mg composite. HAp-Mg was synthesized using the sol-gel method; meanwhile, Chi/HAp-Mg composite was manufactured by mixing Chitosan in acetic acid, and HAp-Mg was added into the mixture. The …

Evaluation Of Primal-Dual Splitting Algorithm For Mri Reconstruction Using Spatio-Temporal Structure Tensor And L1-2 Norm, Mia Rizkinia, Masahiro Okuda

Makara Journal of Technology

Magnetic resonance imaging (MRI) is an essential medical imaging technique which is widely used for medical research and diagnosis. Dynamic MRI provides the observed object visualization through time and results in a spatiotemporal signal. The image sequences often contain redundant information in both spatial and temporal domains. To utilize this characteristic, we propose a spatio-temporal reconstruction approach based on compressive sensing theory. We apply spatio-temporal structure tensor using nuclear norm, in addition to the wavelet sparsity regularization. The spatio-temporal structure tensor is a matrix that consists of gradient components of the MRI data w.r.t the spatial and temporal domains. For …

Influence Of Nh4f In Dextran Based Biopolymer Electrolytes: Conductivity And Electrical Analysis, Muhamad Hafiz Hamsan, Mohd Fakhrul Zamani Kadir, Shujahadeen Bakar Aziz, Muhammad Amirul Solihin Azha, Saifful Kamaluddin Muzakir

Makara Journal of Technology

Dextran polymer host was doped with different concentrations of ammonium fluoride (NH4F) via casting technique. In this present work, dextran-NH4F film has been employed to investigate the ionic conductivity using electrochemical impedance spectroscopy from 50 to 5 MHz. The highest room temperature conductivity is achieved at (2.33 ± 0.76) × 10-3 S cm-1 with 40 wt.% NH4F. The electrolyte is found to obey Arrhenius rule at high temperature with activation energy of 0.21 eV. Dielectric analysis has been performed to obtain better understanding on the conductivity pattern. The dielectric parameters e.g. ɛreal, ɛimag, Mreal, and Mimag have been tested as …

Acute Toxicitystudy Of Choline Based Ionic Liquids Towards Danio Rerio Fish And The Aggregation Behavior Of Their Binary Mixtures, Mansoor Ul Hassan Shah, Nasruddin Nasruddin, Suzana Bt Yusup, Muhammad Moniruzzaman

Makara Journal of Technology

Marine oil spills are effectively controlled by chemical dispersants. However, the toxicity associated with it reduce its employment in marine environment. To overcome this limitation, the acute toxicity of choline based ionic liquids was evaluated as a potential low toxic variant for oil spill remediation. Further, the aggregation behavior of the individual as well as their binary mixtures was also evaluated by employing tensiometry technique. The half-lethal concentration, LC50on zebrafish (Danio rerio) of three choline based ionic liquids showed that the studied ionic liquids (ILs) fall in the range of “practically nontoxic” ( 100-1000 mg L-1).Various micellar properties showed that …

Neutron Diffraction Study Of Multiferroic 0.6nife2o4/0.4batio3 Composite, Engkir Sukirman, Yosef Sarwanto, Syahfandi Ahda, Andon Insani

Makara Journal of Technology

Neutron diffraction study on the 0.6NiFe2O4/0.4BaTiO3 multiferroic composite has been carried out. The 0.6NiFe2O4/0.4BaTiO3 multiferroic composites have been synthesized by solid reaction method. In this study, 20 g of BaTiO3 (BTO) and 20 g of NiFe2O4 (NFO) compounds were prepared from the powder raw materials of BaO3 and TiO2 for BTO, and NiO and Fe2O3 for NFO. Furthermore, both BTO and NFO were each crushed for 5 hours using High Energy Milling (HEM). Then the BTO and NFO were calcined in the furnace at 950 °C/5 hours and 900 °C/5 hours, respectively. Both NFO and BTO precursors were manually mixed …

Multiscale Modeling Of Fracture In Quasi-Brittle Materials Using Bifurcation Analysis And Element Elimination Method, Keyvan Zare Rami

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Analyzing the fracture of heterogeneous materials is a complex problem, due to the fact that the mechanical behavior of a heterogeneous material is strongly dependent on a variety of factors, such as its microstructure, the properties of each constituent, and interactions between them. Therefore, these factors must be effectively taken into account for accurate analysis, for which the multiscale method has been widely used. In this scheme, the computational homogenization method is used to obtain the effective macroscopic properties of a heterogeneous material based on the response of a Representative Volume Element (RVE). The growth of damage in an RVE …

Thermodynamic Model Of Co2 Deposition In Cold Climates, Sandra K. S. Boetcher, Ted Von Hippel, Matthew J. Traum

Publications

A thermodynamic model, borrowing ideas from psychrometric principles, of a cryogenic direct-air CO2-capture system utilizing a precooler is used to estimate the optimal CO2 removal fraction to minimize energy input per tonne of CO2. Energy costs to operate the system scale almost linearly with the temperature drop between the ingested air and the cryogenic desublimation temperature of CO2, driving siting to the coldest accessible locations. System performance in three Arctic/Antarctic regions where the proposed system can potentially be located is analyzed. Colder ambient temperatures provide colder system input air temperature yielding lower CO2 removal energy requirements. A case is also …

Carrying Capacity Of Single-Gauge Railways At Introduction Of Speed Motion Of Passenger-Trains, Saidburkhan Tulaganovich Djabbarov

Journal of Tashkent Institute of Railway Engineers

Results over of complex researches of organization of speed and high-speed motion of passenger-trains are brought on existent single-gauge railways, choice and ground of complex of measures on the increase (to maintenance) of freight and throughput capacity, and ensure continuous operation of the infrastructure of operated railways are presented.

Problems Of The State Of The Rolling Surface Of The Rail Head On Speed And High-Speed Railway Sections Of Jsc "Uzbekistan Temir Yollari", Kuvandik Saginovich Lesov, Igor Ivanovich Kuznetsov, Mukhamedali Kazbek Ugli Kenjaliev, Xushnudbek Odilbekovich Samandarov

Journal of Tashkent Institute of Railway Engineers

In the process of train traffic on the rolling surface of the rail head are formed bumps and fatigue defects, constant dynamic loads lead to the frustration the upper structure of the path. In this article the analyzes integral indicators of the rolling surface of the rails (long waves, medium waves, short waves) on the section of speed and high-speed train traffic for assess the condition of rails in transit. Problems with the formation of wave-like irregularities on the surface of the rails are identified, promising directions in solving this problem are indicated.

Improvement Of Efficiency Of “O‘Zbekiston” Series Electric Locomotive Control System, Usan Berdiev, Malika Nabievna Tuychieva

Journal of Tashkent Institute of Railway Engineers

This article examines the work of efficient use of electric locomotives of the “O‘ZBEKISTON” series operated in the railways of Uzbekistan, storage in working parts, provision of reliable and safe operations, as well as reduction of operating costs and extension of the repair period. For this purpose, during operation, it is constantly necessary to analyze and develop the possibility to achieve planned results using effective methods of technical diagnostics system.

Theoretical Foundations For Determining Kinematic Parameters Of A Jet Unit, Kudrat Raximov, A.R. Babaev, Dilbar Abduraimova

Journal of Tashkent Institute of Railway Engineers

This article discusses the theoretical basis of the dependence of the kinematic parameters, in particular the average speed of flow rate in the suction pipeline of the jet apparatus intended for cleaning water bodies from silting, from changes in the pressure in the mixing chamber. In the problem is considered a single-phase flow, that is, the density of the working and the suction fluid are the same.

Increasing The Efficiency Of Work Of Locomotive Electronic Equipment By Using Portable Diagnostic Devices, Nodir Botirovich Adilov, Nurilla Khayrullayevich Ermatov

Journal of Tashkent Institute of Railway Engineers

This article discusses the current trends in the construction of portable and stationary systems for diagnosing electric and electronic components of locomotives built on integrated chips, as well as presents own model of a portable diagnostic stand for testing electronic devices and electric circuits of locomotives

Evaluation Of The Efficiency Of Flat Sunny Solar Air Heaters With Heat Transfer Turbulizers, Yorkin Sodikovich Abbasov, Muyassar Abubakirovna Umurzakova

Journal of Tashkent Institute of Railway Engineers

The article presents methods for assessing the effectiveness of flat solar air heaters with heat transfer turbulators. The experience of world scientific achievements in the field of increasing the efficiency of solar air heaters is analyzed. The analysis of the effectiveness of flat air heaters. According to the results of the study, it was determined that, in addition to the traditional formula efficiency, for evaluating the effectiveness of flat air heaters with heat transfer turbulators collectors use methods developed in heat engineering and based on the Reynolds analogy.

Comparative Analysis Of Modern Electric Centralization Systems, Asadulla Raximovich Azizov, Elnara Kuandikovna Ametova

Journal of Tashkent Institute of Railway Engineers

This article discusses a comparative analysis of modern electrical centralization systems. The possibilities of developing computer centralizations and centralizations implemented on blocks manufactured using microprocessors are discussed

To The Calculation Of Solid-State Cargo Attachment Under The Influence Of Longitudinal Forces, Khabibulla Turanov, Yadgor Ruzmetov, Jamol Shihnazarov

Journal of Tashkent Institute of Railway Engineers

The article is devoted to the calculation of cargo fastening using the current method. It is proved that according to the existing method, the force in all elastic cargo mounts of both one and the other direction under the influence of longitudinal forces has the same value, regardless of the different location of the geometric parameters of the mounts in space. Calculations of forces in elastic elements of fastening by the specified method are given. The results of the comparative analysis showed that the forces in all wire fasteners, in contrast to the existing method of calculation, have different values. …

Analysis Of Sensors Of The Electronic System For Counting Axles (Eacs) And Firm Altpro Frausсher In The Organization Of Train Traffic, Sunnatillo Tuymurodovich Boltaev, Jonibek Fayzullaevich Kurbonov, Aziz Azimovich Saitov

Journal of Tashkent Institute of Railway Engineers

In this scientific work, the sensors of the electronic system for counting axles of various firms used in level crossings, trunk and station railways of the Republic of Uzbekistan are investigated. Based on the analysis, the parameters of the EACS accounting system are determined. The parameters that led to system crashes were defined in the electronic system for calculating the axes of the EACS. The parameters of the components of the EACS accounting system are determined, which are the main element in determining free loaded roads, reference points, points and sections of arrows. The conditions for using the sensor parameter …

The Role Of Intra-Production Accounting In The Management System Of Enterprises Of Jsc " Uzbekistan Temir Yullari», Aijan Baxtiyarovna Djumanova, Shohruh Vosiljon O’G’Li Ergashev

Journal of Tashkent Institute of Railway Engineers

This article discusses the essence, content and tasks of internal accounting and its role in the management system of enterprises of JSC “Uzbekistan temir yullari”. In order to effectively manage the activities of enterprises need to assess the contribution of each farm unit in the final result of the enterprise activity, the mechanism of which are internal accounting, reporting and analysis of their activity. Managers of enterprises for the development and adoption of management decisions need both General information on the enterprise as a whole, and detailed information on intra – production segments of activity-responsibility centers.

To The Question Of The Mathematical Model Of Rational Planning Of Technological Sections Of The Warehouse, Daurenbek Ihtiyarovich Ilesaliev, Jamol Alisherovich Shixnazarov, Avaz Mirsultanovich Merganov

Journal of Tashkent Institute of Railway Engineers

Modern railway warehouses have an important place in the supply chain.The main task of the railway warehouses is to convert incoming cargo flows with large quantities into outgoing flows.This article discusses the structure of the functioning of a standard railway warehouse.Based on the coating method and methods of V.P. Sityaev developed a rational version of the layout of the railway warehouse, taking into account the cost criteria, representing the amount of logistics costs.Based on the results of the study, three options of non-traditional warehouse planning schemes were obtained and recommended.