Aeronautical Vehicles Commons^™

Airplane Pitch Response To Rapid Configuration Change: Flight Test And Safety Assessment, Ralph Kimberlin, Markus Wilde, Brian Kish, Isaac Silver

Journal of Aviation Technology and Engineering

This paper examines airplane response to rapid flap extension on seven general aviation airplanes. The scenario involves a pilot flying in the traffic pattern becoming distracted, abruptly extending flaps while looking outside the airplane, and failing to notice airspeed and pitch-attitude changes. The airplanes tested reached pitch forces of up to 36 lbf, meeting FAA requirements but exceeding the capability of 55% of the population. Flight data showed a pitch-up to more than 30˚ in 5 s after flap extension, causing airspeed to drop below stall speed for four of the airplanes. At traffic pattern altitudes, stalling an airplane can …

The Impact Of Uas On The Passenger Airline Industry, Matthew Whitten

Senior Honors Theses

This study seeks to cover the state of modern autonomous unmanned aerial systems (UAS) integration into commercial aviation, the future applications of the technology in the airline industry, and the roadblocks currently hindering its integration into passenger operations. Although great advancements are being made in the field, technological developments, economic impact, legal restrictions, airline cost, and public perception stand in the way of the full adaptation of autonomous technology into everyday passenger operations. However, technology is rapidly developing, perhaps allowing for the possibility of autonomous air travel even today, but there are likely years of refinement before regulators, executives, and …

A Reduced Order Model Of The Celestial Icosahedron As The Substructure For A Lighter Than Air Vehicle, Torin C. Quick

Theses and Dissertations

A finite element approach was used to investigate a novel reduced order model to determine the minimum structure dimensionality to support vacuum for a VLTAV. This modeling technique represented the individual segments of the substructure as curved beams with clamped radially-resisted boundary conditions. The full structure was then modeled as a bare structure and structure with skin to validate the results of the reduced order model. The beam geometry for the material Ultem 9085 was determined through this process leading to the 3-D printing of the structure. It was then experimentally tested under uniaxial compression complimented with a FEA model.

The Effects Of Remotely Piloted Aircraft Command And Control Latency During Within-Visual-Range Air-To-Air Combat, David Thirtyacre

Doctoral Dissertations and Master's Theses

The type of military missions conducted by remotely piloted aircraft continues to expand into all facets of operations including air-to-air combat. While future within-visual-range air-to-air combat will be piloted by artificial intelligence, remotely piloted aircraft will likely first see combat. The purpose of this study was to quantify the effect of latency on one-versus-one, within-visual-range air-to-air combat success during both high-speed and low-speed engagements. The research employed a repeated-measures experimental design to test the various hypothesis associated with command and control latency. Participants experienced in air-to-air combat were subjected to various latency inputs during one-versus-one simulated combat using a virtual-reality …

Ram Air-Turbine Of Minimum Drag, Raymond Akagi

Master's Theses

The primary motivation for this work was to predict the conditions that would yield minimum drag for a small Ram-Air Turbine used to provide a specified power requirement for a small flight test instrument called the Boundary Layer Data System. Actuator Disk Theory was used to provide an analytical model for this work.

Classic Actuator Disk Theory (CADT) or Froude’s Momentum Theory was initially established for quasi-one-dimensional flows and inviscid fluids to predict the power output, drag, and efficiency of energy-extracting devices as a function of wake and freestream velocities using the laws of Conservations of Mass, Momentum, and Energy. …

Aircraft Input Files For Pylot And Machupx, Jaden Thurgood

Browse all Datasets

This data was used in an attempt at system identification for rudderless aircraft using simulation.

Can The Timeframe Of Reported Uas Sightings Help Regulators?, Spencer Erik Pitcher, Kelly A. Whealan-George

Beyond: Undergraduate Research Journal

Remotely controlled small aircraft, otherwise known as Unmanned Aircraft Systems (UAS) or drones have started to impact the United States National Airspace System by interfering with the safe flight of aircraft. As the UAS industry continues its expected growth into the future, lawmakers, as well as regulators at the Federal Aviation Administration (FAA) and the aviation community must be able to predict when there will be more UAS craft in the air that could cause an interruption to air traffic so that more resources can be allocated optimally to counter the threat of UAS craft. The purpose of this study …

Tooling Design Modeling For Composite Fuselage Of Beechcraft King Air 250 Using Catia, Miazor Fidelis Ekom

Journal of Aviation Technology and Engineering

Aircraft’s constant operation in tough conditions necessitates the need for structural components of high strength yet low weight. Composite materials are being used as an alternative to conventional aluminum alloys because of their competitive strength-to-weight and stiffness-to-weight ratios. In this paper, the detailed design procedure of a light-aircraft composite material fuselage tooling in three dimensions is shown. In its operation, the layup tools provide a surface for the composite part which is the correct shape of the part and is stable through the cure cycle, and also providing a means of indexing the part for the next manufacturing operation. This …

Viability And Application Of Mounting Personal Pid Voc Sensors To Small Unmanned Aircraft Systems, Cheryl Lynn Marcham, Scott Burgess, Joseph Cerreta, Patti J. Clark, James P. Solti, Brandon Breault, Joshua G. Marcham

Publications

Using a UAS-mounted sensor to allow for a rapid response to areas that may be difficult to reach or potentially dangerous to human health can increase the situational awareness of first responders of an aircraft crash site through the remote detection, identification, and quantification of airborne hazardous materials. The primary purpose of this research was to evaluate the remote sensing viability and application of integrating existing commercial-off-the-shelf (COTS) sensors with small unmanned aircraft system (UAS) technology to detect potentially hazardous airborne contaminants in emergency leak or spill response situations. By mounting the personal photoionization detector (PID) with volatile organic compound …

Development Of Multi-Scale Characterization Techniques For Stress Corrosion Cracking Of Aerospace Alloys, Nicholas Reed

Electronic Theses and Dissertations, 2020-2023

Corrosion presents an inherent challenge in the safe and effective use of metallic aerospace structures for extended periods of time. Progress in the fundamental understanding of corrosion initiation and propagation under stress requires a multi-scale approach that leverages experiments to develop predictive models. Although there exists a large amount of research results tracking the corrosive processes of anodic dissolution and hydrogen embrittlement, the amount of available data and modeling of the micro-scale initiation of corrosion is sparse. This work leverages a suite of characterization techniques to systematically analyze an aerospace grade aluminum alloy AA7075-T6, providing important multi-scale data for correlation …

Measurements Of Wind Turbine Wake Evolution And Trajectory During Morning Boundary Layer Transition And Under Wake Steering Conditions Via Unmanned Aerial Vehicles, Stewart Nelson

Theses and Dissertations--Mechanical and Aerospace Engineering

In July of 2019, a flight campaign was conducted using semi-autonomous Unmanned Aerial Vehicles (UAVs) at the Port Alma Kruger Energy wind farm in Ontario, Canada, to study various aspects of wind turbine wake evolution. Horizontal transects across the wakes were measured using modified fixed-wing aircraft fitted with a five-hole probe to measure the wind velocity vector. Reference boundary layer conditions were measured by an octocopter with an assortment of mounted sensors flying vertical profiles upstream of the turbines. Three experiments were conducted during the campaign, which consisted of a study on wake behavior during the morning boundary layer transition, …

Exploring The Impact Of Composite Material Fires And Associated Response Protocol On The Material Analysis During An Aircraft Accident Investigation, Flavio A. C. Mendonca, Natalie Zimmermann, Peng Hao Wang, Julius Keller

Publications

Metals, beginning in the 1930s, have been frequently used as the material of choice for aircraft construction (Hallion, 1978; Jakab, 1999). Common metals used in the aviation industry range from alloyed and heat-treated aluminum to titanium, magnesium, and superalloys, the latter used in specialized applications (Hallion, 1978; Mouritz, 2012). Nevertheless, a shift in aircraft construction – specifically in terms of the materials used – began in the 1970s, as composite materials were introduced into commercial aircraft (Mouritz, 2012). Among others, the increased use of composited materials was – and still is – propelled by the ability to manufacture comparative lightweight …

Comparative Study On The Prediction Of Aerodynamic Characteristics Of Mini - Unmanned Aerial Vehicle With Turbulence Models, Somashekar V, Immanuel Selwyn Raj A

International Journal of Aviation, Aeronautics, and Aerospace

When dealing with CFD simulations the turbulent nature is seen on most of the engineering flows and these flows need to be solved. Reliable and applicable CFD outputs can be obtained from the accurate modelling of the turbulence as it is one of the most vital elements of CFD modelling. The RANS equations are extensively employed to analyse the complex flows over aircraft and for this purpose, a turbulence model is needed for turbulent flow analyses. Compatible turbulence must be chosen for the exact predictions of aircraft aerodynamic characteristics. In this report, numerical analyses of Mini-UAV are done to compare …

Internet Of Things 36-Rotor Multicopter For Ionizing Radiation Surveying, Svetoslav Zabunov, Garo Mardirossian, Rositsa Miteva, Todor Kunchev

International Journal of Aviation, Aeronautics, and Aerospace

This paper presents an Internet of things 36-rotor unmanned aerial vehicle suitable for radiological surveying of buildings and facilities. The design of the 36-rotor multicopter platform is disclosed. The aircraft is used as a testbed for a lightweight gamma/beta/neutron ionizing radiation sensor closely coupled with the autopilot of the multirotor aircraft. A prototype of the drone and sensor was developed and initial tests were conducted. Test results are presented with data from measuring different radiation sources. The proposed novel design is compared to existing work and advantages to the latter were established.

Time Domain Boundary Element Method Prediction Of Noise Shielding By A Naca 0012 Airfoil, Douglas M. Nark, Fang Q. Hu

Mathematics & Statistics Faculty Publications

As aircraft noise constraints become more stringent and the number/mixture of aircraft configurations grows, it becomes more important to understand the interaction of individual aircraft noise sources with nearby aircraft structures. Understanding these interactions and exploring possible approaches to mitigate or exploit their acoustic impact is essential for overcoming key noise barriers. This paper describes the further validation of a time domain boundary element approach for the prediction of the interactions between incident noise sources and nearby aircraft structures. Predictions were completed for multiple source locations and comparisons of these results with measured data are presented. Overall, very good agreement …

Dji Drone Modification, Sean Lacey, Seth Mancuso, Bryce Mckenzie

Williams Honors College, Honors Research Projects

For this project, we set out to create a lightweight carrying case that would be mounted to a DJI Phantom 3. This case is designed to transport small packages, such as medications, from a delivery vehicle to their final destination. Based on our maximum drone lifting capacity of 600 grams, our case, servomotor, and contents had to weigh less than or equal to that value. The coronavirus pandemic has led to an increase in contactless delivery options along with the push for immunocompromised people to avoid contact with people that may be sick. Our product would help transport necessary supplies …

Small Unmanned Aircraft Systems Acoustic Analysis For Noninvasive Marine Mammal Response: An Exploratory Field Study, David Thirtyacre, Gennifer Brookshire, Sarah Callan, Brittany Arvizu, Patrick Sherman

International Journal of Aviation, Aeronautics, and Aerospace

As in countless other fields of human endeavor, small unmanned aircraft systems (sUAS) have the potential to benefit pinniped (Pinnipedia; e.g., Phocidae [seals], Otariidae [sea lions], and Odobenidae [walruses]) response efforts. The employment of sUAS could give responders a close-up look at animals in distress in order to determine their condition as well as develop a response strategy. However, unlike other subjects that are regularly inspected by sUAS (e.g., croplands and civil infrastructure) pinnipeds may respond to the distinctive sound generated by small, multirotor sUAS. This reaction may include retreating into the water en masse, which could put …

Albatross And Falcon Inspired Bionic Uav: An Aerodynamic Analysis, Bilji C. Mathew, Sagar K. Sahu, Prantik Dutta, Rushi Savale, Muruga Lal Jeyan Jv Dr.

International Journal of Aviation, Aeronautics, and Aerospace

The drone industry yearns for enhanced aerodynamic performance. In order to achieve this feat, researchers and engineers are trying to mimic the natural flyers due to their aerodynamic optimality. One such flyer, the Albatross is an inspiration for many marine drones due to its planform and aerodynamic efficiency. The wing of the plan form is designed and simulated to study its properties. The Bell-Shaped Lift Distribution is incorporated for higher efficiency and elimination of the total downwash produced in case of an Elliptical Lift Distribution. A blended wing body inspired by the Falcon is used for smoother airflow interactions. Furthermore, …

Digitalization Of Educational And Methodological Support For The Training Of Aviation Dispatchers, Zair Ziyaevich Shamsiev

International Journal of Aviation, Aeronautics, and Aerospace

The tasks of improving the educational process of training civil aviation dispatchers on the basis of the development and implementation of digital teaching aids are considered. Legislative and regulatory documents are accepted as an object of digitalization. The end result of the research is expressed in the provision of the educational process with a special electronic educational complex, which has the functions of providing the necessary information and conducting practical exercises to deepen, consolidate and control knowledge in the field of aviation documents.

Aircraft Exhaust Gas Temperature Value Mining With Rough Set Method, Mustagime Tülin Yıldırım Asst. Prof., Mehtap Taşcı

International Journal of Aviation, Aeronautics, and Aerospace

Aircrafts are one of the most important means of transportation today. For aircrafts to be able to serve safely, their maintenance must be done in a timely and complete manner. In addition to regular maintenance, it may appear suddenly; there is also irregular maintenance performed in cases such as lightning strikes, bird strikes, and hard landings. Engine failures and maintenance has great importance in aircraft maintenance. Using the data recorded during the flight by flight data recorder, the engine health condition is monitored and the necessary maintenance procedures are carried out. In this study, the exhaust gas temperature was estimated …

Parallel Anisotropic Unstructured Grid Adaptation, Christos Tsolakis, Nikos Chrisochoides, Michael A. Park, Adrien Loseille, Todd Michal

Computer Science Faculty Publications

Computational fluid dynamics (CFD) has become critical to the design and analysis of aerospace vehicles. Parallel grid adaptation that resolves multiple scales with anisotropy is identified as one of the challenges in the CFD Vision 2030 Study to increase the capacity and capability of CFD simulation. The study also cautions that computer architectures are undergoing a radical change, and dramatic increases in algorithm concurrency will be required to exploit full performance. This paper reviews four different methods to parallel anisotropic grid adaptation. They cover both ends of the spectrum: 1) using existing state-of-the-art software optimized for a single core and …

Constrained Motion Analysis Of Spacecraft Trajectory In Restricted Three Body Problem, Harshkumar Patel

Doctoral Dissertations and Master's Theses

Due to the popularity of libration points, many satellites are being maintained on their desired trajectory. Indian space research organization has planned to launch the Aditya-L1 spacecraft to study about the Sun by 2021. James Webb Space Telescope has also been designed to observe deep space at L2 in the Sun-Earth system by 2021. The combined gravity of the Earth and the Sun keep satellite’s orbit locked at libration points. Though satellites enjoys an uninterrupted view of Sun and Earth all the time, they are affected by the solar radiation pressure (SRP) continuously. Due to the instability of collinear libration …

Hexakis Icosahedron Frame-Skin Vacuum Lighter Than Air Vehicle, Brian Cranston, Anthony N. Palazotto

AFIT Patents

A vacuum lighter than air vehicle (VLTAV) includes a rigid frame of rods connected together to form a hexakis icosahedron. A membrane skin covers the rigid frame and defines therewith a vessel configured to hold an internal vacuum that allows the vessel to float in the air. The plurality of rods and membrane skin have weights and dimensions that result in a neutral and/or positive buoyancy for the vessel while preventing geometric instability.

An Investigative Study Of Combustion And Emissions With Noise And Vibrations Of Synthetic Fuels Within An Aero-Gas Turbine, Camille J. Phillips

Honors College Theses

The pollution from the aerospace transportation is rapidly becoming the largest source of greenhouse gas (GHG) emissions. The FAA expects aviation emissions to almost triple by 2050, making the aerospace industry responsible for the release of approximately 25% of the global carbon dioxide budget. These aviation emissions, including CO2 and NOx, as well as other GHGs, contribute to the destruction of ozone layer. Carbon dioxide emissions have a particularly negative effect on humans, leading to airway diseases especially in children and elderly. To combat the addition of further GHG emissions into the atmosphere, it is necessary to minimize the usage …

Celebrating 90-Orbits Around The Sun, Stafford Air & Space Museum

Programs

In celebration of the 90th birthday of Oklahoma astronaut and aerospace legend, Gen. Thomas P. Stafford, the Stafford Air & Space Museum in Weatherford, Oklahoma is offering free admission on September 17th, 2020.

Unless stated otherwise within this repository collection, all materials are shared under the following Creative Commons license: [Creative Commons Attribution-NonCommercial 4.0 International License].

Arliss Lite: An S4 Pocketqube Falcon 9 Airframe, Ken Biba

Robert "Bob" Twiggs STEM Education Collection

A report authored by Ken Biba titled "ARLISS Lite: An S4 PocketQube Falcon 9 Airframe" from September of 2020.

Three-Dimensional, Vision-Based Proportional Navigation For Uav Collision Avoidance, Guanhong Gao

Doctoral Dissertations and Master's Theses

As the number of potential applications for Unmanned Aerial Vehicles (UAVs) keeps rising steadily, the chances that these devices will operate in close proximity to static or dynamic obstacles also increases. Therefore, collision avoidance is an important challenge to overcome for Unmanned Aerial Vehicle operations. Electro-optical devices have several advantages such as light weight, low cost, low algorithm requirements with respect to computational power and possibly night vision capabilities. Therefore, vision-based Unmanned Aerial Vehicle collision avoidance has received considerable attention. Although much progress has been made in collision avoidance systems (CAS), most approaches are focused on two-dimensional environments. In order …

Power-Over-Tether Uas Leveraged For Nearly-Indefinite Meteorological Data Acquisition, Daniel Rico, Carrick Detweiler, Francisco Muñoz-Arriola

School of Computing: Dissertations, Theses, and Student Research

Use of unmanned aerial systems (UASs) in agriculture has risen in the past decade. These systems are key to modernizing agriculture. UASs collect and elucidate data previously difficult to obtain and used to help increase agricultural efficiency and production. Typical commercial off-the-shelf (COTS) UASs are limited by small payloads and short flight times. Such limits inhibit their ability to provide abundant data at multiple spatiotemporal scales. In this paper, we describe the design and construction of the tethered aircraft unmanned system (TAUS), which is a novel power-over-tether UAS leveraging the physical presence of the tether to launch multiple sensors along …

Development Of High-Density Propulsion System Technologies For Interplanetary Small Satellites And Cubesats, Morgan Andrew Roddy

Graduate Theses and Dissertations

The goal of this research was to support the development of a novel propulsion system for small satellites (<180 kg) and CubeSats. This was pursued by conducting a collection of studies that were designed to provide engineering data that would be critical in designing a functional prototype. The novel propulsion system was conceived by the author to provide best-in-class performance for the small satellite and CubeSat families of spacecraft. This context presents specific design requirements that the presented technology attempts to satisfy. The most critical among these is high density; the propellant was designed to be stored with high density and the thruster was designed to be as compact as possible. The propulsion system is composed of two primary elements, a propellant generator and a thruster. The propellant generator works by sublimating a solid crystal into vapor and then using this vapor to etch a dense metal. The resulting gaseous byproducts of this reaction are the propellant. This dissertation used xenon difluoride (XeF2) vapor to etch tungsten (W) which react to form xenon gas (Xe) and tungsten hexafluoride (WF6). This approach gave a theoretical propellant storage density 5.40 g/cm3; and 5.17 g/cm3 was demonstrated. The sublimation dynamics of the XeF2 were studied as a function of surface area and temperature and it was found to be suitable for the intended application due to its high effluence rate; that is, it sublimates fast enough to be useful. The sublimation rates are on the order of 10’s of µg/s. The etch rate of XeF2 on W was also studied and found to be suitably fast to provide useful amounts of reactants for use as a propellant, again on the order of 1’s of µg/s. The thruster is an electrostatic radio frequency (RF) ion thruster design and is manufactured with Low Temperature Co-Fired Ceramic (LTCC) materials system and manufacturing technology. Manufacturing samples of the thruster were built at the University of Arkansas in July 2015 and tested at NASA’s Marshall Space Flight Center in May 2018. Testing validated the viability of the LTCC thruster and provided valuable information on how to improve the thruster’s design.

Aerodynamic And Aeroacoustic Performance Of Small Uav Propellers In Static Conditions, William Jordan, Robert W. Deters, Shreyas Narsipur

Publications

The proliferation of small multi-rotor UAVs in commercial, recreational, and surveillance spheres has garnered significant interest in the noise produced by these vehicles. The current research aims to study the relationship between the aerodynamic performance and acoustic characteristics of small-scale UAV propellers. Three commercially available propellers for the DJI Phantom 2/3 UAV were selected for preliminary development and validation of an aeroacoustic experimental test setup and associated data reduction methods. Propeller thrust, torque, and power measurements were recorded at static conditions. Upon successful validation of the test bench, acoustic measurements were taken at the propeller disk’s upstream and in-plane locations. …