Architectural Engineering Commons^™

Building And Maintaining Plankhouses At Two Villages On The Southern Northwest Coast Of North America, Emily Evelyn Shepard

Dissertations and Theses

Plankhouses were functionally and symbolically integral to Northwest Coast societies, as much of economic and social life was predicated on these dwellings. This thesis investigates both plankhouse architecture and the production of these dwellings. Studying plankhouse construction and maintenance provides information regarding everyday labor, landscape use outside of villages, organization of complex tasks, and resource management.

This thesis investigates three plankhouse structures at two sites, Meier and Cathlapotle, in the Lower Columbia River Region of the southern Northwest Coast of North America. Methods consisted of digitizing over 1,100 architectural features, creating detailed maps of architectural features, and conducting statistical and …

A Comparative Study Of The Mechanical Properties, Fracture Behavior, Creep, And Shrinkage Of Chemically Based Self-Consolidating Concrete, Mahdi Arezoumandi, Mark Ezzell, Jeffery S. Volz

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study presents the results of an experimental investigation that compares the mechanical properties, fracture behavior, creep, and shrinkage of a chemically based self-consolidating concrete (SCC) mix with that of a corresponding conventional concrete (CC) mix. The CC and SCC mix designs followed conventional proportioning in terms of aggregate type and content, cement content, air content, water-cementitious materials (w/cm) ratio, and workability. Then, using only chemical admixtures, the authors converted the CC mix to an SCC mix with all of the necessary passing, filling, flowability, and stability requirements typically found in SCC. The high fluidity was achieved with a polycarboxylate-based …

An Experimental Investigation Of Crumb Rubber Concrete Confined By Fibre Reinforced Polymer Tubes, Osama Youssf, Mohamed Elgawady, Julie E. Mills, Xing Ma

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Due to the known loss of compressive strength experienced by crumb rubber concrete (CRC) compared with conventional concrete, there have been few applications explored to date for the structural use of these materials. This paper describes experimental work conducted to explore the possible future use of CRC for structural columns by evaluating the use of fiber reinforced polymer (FRP) confinement as a means of overcoming the material deficiencies (decreased compressive strength). The results indicated that the use of FRP to confine rubberized concrete effectively negates the decrease in strength and retains the advantages of increased ductility that arise from rubberized …

Plant Translocation Of Organic Compounds: Molecular And Physicochemical Predictors, Matt A. Limmer, Joel Gerard Burken

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Root-Soil Boundary Represents One of the Largest Global Biotic-Abiotic Mass-Transfer Interfaces and is a Primary Pollutant Entry Point to the Food Chain. This Interface is Also Critically Important in Phytoremediation Efforts and Herbicide Design. Experimental Data and Single-Parameter Models Have Resulted in the Current Understanding that Moderately Hydrophobic Organic Compounds Are Most Likely to Be Translocated by Plants, Although Recent Evidence Indicates Plants Can Also Translocate Some Hydrophilic Compounds. Molecular Descriptors Initially Applied for Drug Discovery and for Transmembrane Migration in Mammalian Systems Were Applied Here to Determine the Physicochemical Domains and Weighted Desirability Functions to Identify Compounds Amenable …

Performance Of No Vibration/No Admixture Masonry Grout Containing High Replacement Of Portland Cement With Fly Ash And Ground Granulated Blast Furnace Slag, Eric Bateman

Master's Theses

When hollow concrete masonry is used for construction in high seismic regions, structural designs typically require fully grouted walls. The grouting process is labor-intensive, time-consuming and has a high energy demand due to requirements of consolidation in each and subsequent grout lifts. Self-consolidating grout with admixtures has been successfully used without segregation in walls of up to 12.67 ft. in height. Investigation of self-consolidating grout mixes without admixtures has potential for sustainability improvement.

This thesis reports on the compression strength and consolidation observations of self-consolidating characteristics of no vibration/no admixture grout made by substituting various proportions of Portland cement with …

Improving The Hydraulics Of Drinking Water Contact Tanks Using Random Packing Material, Taylor C. Barnett, Justin J. Kattnig, Subhas K. Venayagamoorthy, Gordon Whittaker

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study investigated the use of industrial packing material for increasing the hydraulic efficiency of small-scale, chlorine contact tanks used in drinking water treatment. The packing material used in the study was spherical, with porosities between 0.9 and 0.95 and a density less than that of water. A total of 67 tracer studies, conducted on laboratory-scale chlorine contact tank systems, investigated three sizes of packing material, two tank sizes, and two flow rates. Sodium chloride solution was injected as a continuous tracer and was monitored in the tank outflow through electrical conductivity. Several studies were validated with the use and …

The Bridge Newsletter Spring 2014, Missouri University Of Science And Technology

The Bridge Newsletter

-Reusing scrap tires
-Renaissance man
-Energy research published
-Follow your passion

Method And System For Optimal Coordination Control And Soft Repair Of Multiple Rooftop Heating And Cooling Units, Haorong Li

Durham School of Architectural Engineering and Construction: Faculty Publications

Techniques are described that may be implemented in an adaptive control device to regulate multiple zone environmental units based upon multiple temperature values and multiple airflow values, where each temperature value and each airflow value is related to the temperature and the airflow in a specific zone. In an implementation, the input interface of the adaptive control device is configured to receive multiple temperature values and multiple air flow values from multiple zone sensors. The adaptive control device may calculate multiple operational values based on the multiple temperature values and the multiple air flow values. An operational value indicates a …

2014 Scholarly Productivity Report, Missouri University Of Science And Technology

Civil, Architectural and Environmental Engineering Scholarly Productivity Reports

No abstract provided.

The Steel Yard, Architecture Department, Sculpture Department, Bruner Foundation

Rudy Bruner Award | 30 Years of Urban Excellence

The Steel Yard redeveloped a historic steel fabrication facility into a campus for arts education, job training, and small-scale manufacturing in Providence, Rhode Island. The 3.5-acre property in the city’s Industrial Valley required extensive environmental remediation to meet regulatory requirements while retaining the industrial urban character of the site. The Steel Yard offers classes, workforce training, and fabrication space for local artists, creating an industrial arts incubator where they can share ideas, materials, and space. It has become a center for creative activity, bridging the gap between the traditional arts community on the affluent east side of Providence with manufacturing …

Compressibility Characteristics Of Low-Plasticity Silt Before And After Liquefaction, Shuying Wang, Ronaldo Luna

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Low-plasticity silt is known to have a potential to liquefy during earthquakes. The compressibility characteristics could change before and after a dynamic event that produces liquefaction. This research investigates the liquefaction resistance and post liquefaction reconsolidation characteristics of Mississippi River Valley (MRV) silt using laboratory cyclic triaxial compression testing. The MRV silt experienced initial liquefaction under cyclic loading, and the results are presented as cyclic stress ratio versus loading cycle curve. After cyclic loading, the liquefied specimens were reconsolidated. Permeability did not change significantly as a result of liquefaction. The reconsolidation curves are more parallel to the compression line than …

Characterization Of Shear Wave Velocity And Its Anisotropy In Uniform Granular Materials, Xin Kang, Bate Bate, Louis Ge

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Small strain stiffness of granular materials is important to many engineering applications, such as earthquake engineering, pavement, machine foundation, embankment subjected to tidal impacts, and foundations for structures under wind loads. Shear wave velocity, which is an indicator of stiffness, was measured with a newly developed bender element testing system. Test data supported that this testing system is effective in evaluating the shear wave velocity and its anisotropy of uniform spherical granular materials, including glass beads, uniform medium, and fine sands. Influencing factors on the Vs such as grain size and applied stress were studied. Two components of the soil …

Effects Of Mix Design Parameters And Rheological Properties On Dynamic Stability Of Self-Consolidating Concrete, B. Esmaeilkhanian, Kamal Khayat, A. Yahia, D. Feys

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Stability is a crucial property for successful placement and performance of self-consolidating concrete (SCC). Dynamic stability refers to the segregation resistance of concrete during flow and is not thoroughly described in literature to date. In this research, a newly developed dynamic stability test, the Tilting-box test, was employed to evaluate the effect of different mix design parameters on the dynamic segregation of SCC. Paste volume, water-to-binder ratio (w/b), maximum size of aggregate (MSA), aggregate density, and aggregate grain-size distribution were shown to affect the dynamic stability of SCC, while the coarse aggregate shape did not have a significant influence. The …

Cyber-Physical Codesign Of Distributed Structural Health Monitoring With Wireless Sensor Networks, Gregory Hackmann, Weijun Guo, Guirong Yan, Zhuoxiong Sun, Chenyang Lu, Shirley Dyke

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Our Deteriorating Civil Infrastructure Faces the Critical Challenge of Long-Term Structural Health Monitoring for Damage Detection and Localization. in Contrast to Existing Research that Often Separates the Designs of Wireless Sensor Networks and Structural Engineering Algorithms, This Paper Proposes a Cyber-Physical Codesign Approach to Structural Health Monitoring based on Wireless Sensor Networks. Our Approach Closely Integrates 1) Flexibility-Based Damage Localization Methods that Allow a Tradeoff between the Number of Sensors and the Resolution of Damage Localization, and 2) an Energy-Efficient, Multilevel Computing Architecture Specifically Designed to Leverage the Multiresolution Feature of the Flexibility-Based Approach. the Proposed Approach Has Been Implemented …

Linking Solid Particle Packing Of Eco-Scc To Material Performance, Florian V. Mueller, Olafur H. Wallevik, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The concept of Eco-SCC aims to achieve self-compacting concrete (SCC) design for intermediate compressive strength mixtures that are commonly used in the ready-mix concrete industry. Contrary to many other approaches, in which the reactive cement clinker is replaced by a less reactive component, Eco-SCC involves the reduction of the total powder content. In the approach presented in this paper, the lubricant volume is increased by using a non-reactive filler. An improved particle packing with an enhanced lattice effect can minimize the lubricant demand and enhance the stability of the concrete. The effect of particle-size distribution on stability and performance of …

Impact Of Organic Coatings On Frictional Strength Of Organically Modified Clay, B. Bate, Q. Zhao, S. E. Burns

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Organic matter is frequently encountered in both naturally occurring and engineered particulate media. Charged functional groups in the organic matter can lead to cation exchange within the clay interlayer, which results in the formation of an organic coating on the clay surfaces and alters the interfacial frictional regime in the soil mass. This study investigated the triaxial shear frictional behavior of montmorillonite particles coated with a controlled organic phase composed of quaternary ammonium cations. Through cation exchange, organic cations were loaded onto the clay's interlayer exchange sites, with control on the density of organic coverage and structure of the organic …

Effects Of Chemical Stabilizers On An Expansive Clay, Honghua Zhao, Louis Ge, Thomas M. Petry, Yi Zhen Sun

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Expansive clays exhibit a high potential for the volume change behavior when the soil moisture changes. The estimated annual cost of the damage to the facilities built on expansive clay in the United States exceeds 9 billion dollars. Because of the physicochemical nature of the expansive clay, the use of chemical agents to improve their engineering properties is common. This research investigated the effects of chemical agents on an expansive soil from Texas through a laboratory injection method. The agents used in this study included lime, potassium-based agents, and a group of ionic agents. Swelling tests, chemical tests, and soil …

Stock Aggregation Model And Virtual Archetype For Large Scale Retrofit Modelling Of Local Authority Housing In Ireland, James Pittam, Paul D. O’Sullivan, Garrett O’Sullivan

Conference Papers

Developing representative archetypes using a bottom up approach for stock modelling is an excellent tool for evaluating the overall performance of the building stock; however it requires detailed analysis of the various building types. Currently there is no detailed housing data base for Local Authority housing in Cork City, Ireland that catalogues the housing stocks geometric properties and thermal characteristics for each typology. This study details a methodology to catalogue the LAH stock and build a detailed housing data base. The GIS web based mapping application Google Street View is used to identify 20 house typologies across 36 LAH developments; …

A Simple Turbulence Model For Stably Stratified Wall-Bounded Flows, F. Karimpour, S. K. Venayagamoorthy

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this study, we present a simple zero-equation (algebraic) turbulence closure scheme as well as the standard k-Ïμ model for stably stratified wall-bounded flows. We do this by proposing a parameterization for the turbulent Prandtl number (Prt) for stably stratified flows under the influence of a smooth solid wall. The turbulent Prandtl number is the linking bridge between the turbulent momentum and scalar fluxes in the context of Reynolds-averaged Navier-Stokes (RANS) simulations. Therefore, it is important to use appropriate parameterizations for Prt in order to define the right level of momentum and scalar mixing in stably stratified flows. To date, …

Fit For Renting:An Investigation Into Space Standards Of Irish Housing, Jim Roche, Noel Brady

Books/Book Chapters

No abstract provided.

Shear Strength Of Chemically Based Self-Consolidating Concrete Beams: Fracture Mechanics Approach Versus Modified Compression Field Theory, Mahdi Arezoumandi, Jeffery S. Volz

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

An experimental investigation was conducted to study the shear strength of full-scale beams constructed with both chemically based self-consolidating concrete (SCC) and conventional concrete (CC). This experimental program consisted of 12 beams without stirrups with three different longitudinal reinforcement ratios. The beams were tested under a simply supported four-point loading condition. The experimental shear strengths of the beams were compared with the shear provisions of both U.S. and international design codes. Furthermore, the shear strengths of the beams were evaluated based on fracture mechanics approaches, modified compression field theory (MCFT), and a shear database of CC specimens. Results of this …

Safety Effect Of Missouri's Strategic Highway Safety Plan: Missouri's Blueprint For Safer Roadways, Mojtaba A. Mohammadi, V. A. Samaranayake, Ghulam H. Bham

Mathematics and Statistics Faculty Research & Creative Works

This study systematically evaluated the changes in motor vehicle crashes that occurred on the Missouri Interstate highway system following the implementation of the Missouri Strategic Highway Safety Plan (MSHSP) between 2004 and 2007. The MSHSP implemented crash injury reduction strategies in enforcement, education, engineering, and public policy. Empirical Bayesian methods were commonly used to evaluate the effects of any change in safety as a result of countermeasures. This paper presents a simple new approach to evaluating the effects of Missouri's safety plans on roadway crashes. For crash data associated with traffic and roadway characteristics, negative binomial regression models were developed …

Full-Scale Field Testing Of Micropiles In Stiff Clay Subjected To Combined Axial And Lateral Loads, Kyle A. Kershaw, Ronaldo Luna

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

A series of full-scale micro piles was installed at a site in mid-Missouri for a load-test program to study the effect of combined loading. The micro piles were installed with a 178-mm (7-in.) outer diameter steel casing to a depth of 4.6 m (15 ft) and a bond zone length of 3.0 m (10 ft). The surficial soils at the site consisted of stiff-to-hard clay underlain by weathered silty/sandy shale where the bond zone of the micro piles was located. The load-test program included axial, lateral, and combined-load tests. The ultimate axial and lateral capacity of the piles was initially …

Thermophysical And Mechanical Properties Of Hardened Cement Paste With Microencapsulated Phase Change Materials For Energy Storage, Hongzhi Cui, Wenyu Liao, Shazim Ali Memon, Biqin Dong, Waiching Tang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this research, structural-functional integrated cement-based materials were prepared by employing cement paste and a microencapsulated phase change material (MPCM) manufactured using urea-formaldehyde resin as the shell and paraffin as the core material. The encapsulation ratio of the MPCM could reach up to 91.21 wt%. Thermal energy storage cement pastes (TESCPs) incorporated with different MPCM contents (5%, 10%, 15%, 20% and 25% by weight of cement) were developed, and their thermal and mechanical properties were studied. The results showed that the total energy storage capacity of the hardened cement specimens with MPCM increased by up to 3.9-times compared with that …

Role Of Solids Retention Time On Complete Nitrification: Mechanistic Understanding And Modeling, Guoqiang Liu, Jianmin Wang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Effects of solids retention time (SRT) on both steps of the nitrification process (e.g., ammonia oxidation and nitrite oxidation) and the nitrifier community in a complete-mix activated sludge process were studied. At a SRT less than or equal to 20 days, the effluent ammonia concentration was lower than the effluent nitrite concentration. At the 40-day SRT, however, the effluent nitrite concentration became equal to or less than the effluent ammonia concentration. Quantitative Polymerase Chain Reaction (QPCR) assays indicated that increasing SRT significantly increased nitrite-oxidizing bacteria/ammonia-oxidizing bacteria (NOB/AOB) ratio. Further investigation indicated that Nitrosomonas europaea/eutropha were the dominant AOB for ammonia …

Form Pressure Generated By Fresh Concrete: A Review About Practice In Formwork Design, Tilo Proske, Kamal Khayat, Ahmed Omran, Olaf Leitzbach

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this paper, several current industrial practices in formwork design are presented focusing on the normative calculation of the form pressure. Most of the current Standards are devoting for the design of the formwork for the normal vibrated concrete. Currently, the Standards are being updated to include provisions for the newly adapted concrete, such as the flowable concrete and self-consolidating concrete. However, the experience with these methods is still limited. The available methods for calculating the formwork pressure for the flowable concrete and SCC are based on measuring the shear strength of concrete using different concepts, such as the setting …

Use Of Innovative Techniques To Enhance The Hydraulic Disinfection Efficiency Of Drinking Water Contact Tanks, J. J. Kattnig, S. K. Venayagamoorthy

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The focus of this study was to understand the complex nature of flow dynamics within water disinfection contact tanks and to use this understanding in the development of beneficial tank modifications. Methods involved in this process included the use of computational fluid dynamics (CFD) and physical conservative tracer studies. Attempted tank alterations included the installation of baffles, inlet modification, and the use of industrial packing material. Tested modifications aimed at altering existing velocity fields to increase the hydraulic disinfection efficiency of a given system. Hydraulic efficiency was measured through the use of residence time distribution (RTD) curves and the well-known …

Behavior Of Hybrid Frp-Concrete-Steel Double-Skin Tubes Subjected To Cyclic Axial Compression, Omar I. Abdelkarim, Mohamed A. Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents the results of an experimental study that was conducted to investigate the effects of key parameters on the compressive behavior of fiber-reinforced polymer (FRP)-concrete-steel double-skin tubular columns (FSDT). Hybrid FSDT columns have been introduced as a new form of hybrid columns. They consist of an outer tube made of FRP and inner tub made of steel, with sandwiched concrete between them. This paper investigated the effect of fiber angle and the ratio of steel tube diameter to its thickness (Di/ts) on the compressive behavior of FSDT columns. Six FSDT cylinders with different (Di/ts), in addition to two …

Choice Of Thixotropic Index To Evaluate Formwork Pressure Characteristics Of Self-Consolidating Concrete, Ahmed F. Omran, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Formwork lateral pressure exerted by concrete is affected by mixture composition, placement conditions, and formwork characteristics. The mixture composition includes binder type and content, supplementary cementitious materials, fillers, water-to-cementitious ratio, content and characteristics of coarse aggregate, paste volume, chemical admixtures, concrete unit weight, concrete consistency, and temperature. Thixotropy of concrete expressed here in terms of structural build-up at rest is employed to collectively reflect the effect of combined mix design factors on formwork pressure. This research demonstrates relationships between 12 indices that can be used to evaluate the structural build-up at rest of concrete, determined using portable vane, inclined plane, …

The Potential For Energy Reduction In Uk Commercial Offices Through Effective Management And Behaviour Change, Mark Mulville, Keith Jones, Gesche Huebner

Articles

eneral office equipment can be responsible for a significant proportion of overall electrical energy consumption in UK offices and this is predicted to rise significantly over the coming years [Webber, C. A., Roberson, J. A., Brown, R. E., Payne, C. T., Nordman, B., & Koomey, J. G. (2001). Field surveys of office equipment operating patterns. Berkley: CA: Lawrence Berkley National Laboratory]. As a significant contributor to overall energy use, this equipment has a corresponding cost and carbon impact. The legally binding requirements of the climate change act [Department of Energy and Climate Change. (2008 Department of Energy and …