Architectural Engineering Commons^™

Effect Of Rheology Modification On Fiber Orientation And Dispersion In 3d-Printed Ultra-High-Performance Concrete, Haodao Li, Alfred Addai-Nimoh, Seongho Han, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The extrusion process in 3D concrete printing (3DCP) facilitates horizontal alignment of steel fibers along the printing direction, thus enhancing the load-bearing capacity of printed elements. However, such shear-induced fiber alignment is highly sensitive to rheological properties. This study investigates how variations in dynamic yield stress (τd) and plastic viscosity (μ), influence the extrudability, fiber orientation and dispersion, and anisotropic mechanical behavior of ultra-high-performance concrete (UHPC). Five viscosity-modifying agent (VMA) types were incorporated at two content levels to modify the rheology of printable UHPC. Results showed that moderate VMA additions improved printability, whereas excessive contents markedly increased τd and μ; …

Transforming Dredged Sediment Into Reactive Clay: Critical Review Of Calcination, Reactivity, And Sustainable Valorization As Supplementary Cementitious Material, Seongho Han, Sanghwon Wi, Koochul Ji, Keun Hyeok Yang, Farshad Rajabipour, Kamal H. Khayat, Jinyoung Yoon

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Dredged sediment (DS) is generated worldwide in large volumes through routine port and waterway maintenance, yet its disposal presents environmental and economic challenges. Recently, calcined dredged sediment (CDS) has emerged as a supplementary cementitious material (SCM), offering a viable alternative to traditional SCMs, such as fly ash and slag cement. This review synthesizes current knowledge on the physical, chemical, and mineralogical characteristics of raw DS and pretreatment strategies aimed at dewatering, organic matter removal, and contaminant stabilization. The effects of calcination on the production of reactive amorphous aluminosilicates are also discussed. Emphasis is placed on physicochemical changes revealed by experimental …

Design And Implementation Of A Honeycomb Damping System For The 2026 Eeri Seismic Design Competition, Vera Nguyen, Lauryn Wojcik

Architectural Engineering

The authors of this report were a part of the 2026 Earthquake Engineering Research Institute (EERI) chapter at California Polytechnic State University, San Luis Obispo. In July 2026, they will travel to Portland, Oregon with 12 students to compete in the Undergraduate Seismic Design Competition hosted by EERI. The competition required teams to develop a comprehensive structural design proposal that included computer-based modeling and analysis, construction of three physical models, and the preparation of both a technical poster and oral presentation for a proposed high-rise building located in Portland, Oregon. Cal Poly’s “Illahee Tower” was designed with an emphasis on …

Impact Of Femalized Kinesthetic Learning Model On African American Middle School Girls’ Career Interest, Mercy F. Fash, Andrea Ofori-Boadu

Journal of Global Education and Research

Engaging African American middle school girls in out-of-school-time (OST) Architecture, Engineering, and Construction (AEC) programs can boost interest in male-dominated AEC careers. This study adopts Lent’s Social Cognitive Career Theory to evaluate the impact of an OST feminized AEC kinesthetic learning model (fAEC-KLM) on the career interests of this demographic. Through a qualitative research approach, fourteen (14) African American middle school girls from Guilford County, NC, completed pre- and post-interviews on how fAEC-KLM interactions influenced their AEC career interests. Inductive thematic analysis was carried out on transcribed interviews. Results show that effective components, such as lectures on AEC, bridge construction …

Bond Behavior Of Full-Scale Beams Using Sustainable Self-Compacting Concrete, Hayder H. Alghazali, Atheer H.M. Algburi, John J. Myers

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Sustainable concrete is a step towards greener and more eco-friendly concrete construction practices, helping to solve global environmental problems. The present study focuses on the bond behavior between steel reinforcement and greener self-compacting concrete, specifically sustainable self-compacting concrete (SUS-SCC). Three SUS-SCC mixtures with different fly ash (FA) to cement replacement levels of [50, 60, and 70% (by mass)] were developed. Twelve full-scale SUS-SCC beams with a cross-section of (305 x 57) mm and a total length of 3048 mm were cast and tested using a four-point load test setup. The effect of longitudinal and lateral steel reinforcement ratios in the …

Mass Timber Construction: Products, Performance And Design, Anthony Harvey

Civil Engineering Professional Development Seminar

Due to their high strength, dimensional stability and positive environmental performance, mass timber building products are quickly becoming materials of choice for sustainably‐minded designers. This presentation will provide a detailed look at the variety of mass timber products available, including glue‐laminated timber (glulam), cross laminated timber (CLT), nail laminated timber (NLT), heavy timber decking, and other engineered and composite systems. Applications for the use of these products under modern building codes will be discussed, and examples of their use in U.S. projects reviewed. Mass timber’s ability to act as both structure and exposed finish will also be highlighted, as will …

Co2-Induced Changes In Rheology, Structural Evolution, And Particle Characteristics Of Cement Paste, Seongho Han, Tae Yong Shin, Seung Mo Kim, Jae Hong Kim, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The injection of carbon dioxide (CO₂) into cementitious systems has emerged as a promising approach to enhancing sustainability in concrete production. This study explores the impact of CO₂ injection on the rheological behavior, structural build-up, and particle size evolution of cement paste by systematically varying the water-to-cement ratio (w/c) (0.35, 0.4, and 0.5) and CO₂ concentration (0.06, 0.28, and 0.84 mol). Rheological analysis revealed a significant increase in initial yield stress with CO₂ injection. Using the Modified Bingham model, yield stress increased by 72 % and 150 % for 0.28- and 0.84-mol CO₂, …

The Xenaform, Cassadie J. Golding

Architectural Engineering

The XenaForm explores how complex, expressive structures can emerge from simple, low-tech construction methods using principles of parametric design and structural geometry. By combining folded plate techniques with modular tetrahedral components, the project bridges high-tech digital modeling and hands-on physical fabrication. The result is a lightweight, buildable system that reclaims the engineer’s role as a form-finder.

Architectural Engineering Institute: International Student Design Competition 2025, Alexandra Marie Kersting, Alec Thomas Gibbs, Haley Francesca Sousa, Kline Genevieve Nickel

Architectural Engineering

The AEI International Student Design Competition is an annual competition held by the Architectural Engineering Institute that aims to replicate an integrated building design process. The 2025 Cal Poly team consisted of 4 Architectural Engineering students, each competing in the Structural and Integration disciplines. The team was provided a set of architectural drawings and a 3D architectural Revit model of Carson Headquarters in Omaha, Nebraska. The team was tasked with the creation of a complete structural design as well as a discussion of integration of other building design disciplines.

Increasing Drift Capacity Of Non-Ductile Concrete Shear Walls Through Confinement With Fiber-Reinforced Polymer Application, Andrew Duong, Sophia Maglabe, Sheyna Rongong

Architectural Engineering: Graduate Reports

The seismic response and laboratory testing of pre-1980s reinforced concrete (RC) shear walls commonly exhibit undesirable concrete crushing and rebar buckling in the wall end-zones leading to a flexural compressive failure. The lack of ductility of these walls is attributed to low reinforcement ratios and absence of special boundary elements (SBE) as required by modern design code. Thus, the authors are proposing a fiber reinforced polymer (FRP) retrofit method to provide confinement to the end-zones of pre-1980s walls equivalent to that of an SBE. Current industry applications of FRP have largely been for shear strengthening of RC beams, columns, and …

Anti-Corrosion Performance Of Magnesium Potassium Phosphate Cement Coating On Steel Reinforcement: The Effect Of Boric Acid, Fan Zhang, Jihui Qin, Kangyi Cai, John J. Myers, Hongyan Ma

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

It has recently been found that magnesium potassium phosphate cement (MKPC) paste coating applied on the surface of steel reinforcement can effectively retard the onset of corrosion and suppress corrosion reactions. However, the fast-setting nature of MKPC—which is a merit in repair—can be problematic in a practical engineering process of coating the steel reinforcement with MKPC paste. To address this problem, boric acid (H₃BO₃) was added as a retarder in an MKPC formulation to prolong the setting time. This work investigated the impact of boric acid (at 5% by weight of MgO) on the anti-corrosion performance …

Seismic Resilience Of Timber Homes, Melia R. Costa

College of Engineering Summer Undergraduate Research Program

The vast majority of residential buildings in California are wood-frame structures. A home is typically a very large investment for families, and damage to the home can be detrimental to a family’s economic success. Thus, reducing the economic impacts of an earthquake on residential timber housing is crucial. A full scale, two-story section of a residential timber house is in construction in the Parson’s Geotechnical and Earthquake Engineering Laboratory on the Cal Poly campus in San Luis Obispo, California. Once built it will be put through earthquake simulation tests on a shake table with various magnitudes of seismic activity. Next, …

Engineering-Enhanced Theatre: How Engineering Involvement Can Aid Regional Theatres, Albert M. Le

Architectural Engineering

Engineering and theatre are disciplines not often associated with each other within regional and small theatre companies in the United States. The distinction between the two fields of study is not simply from the fundamental differences between how each field is taught and practiced, but also the difficulties encountered within a scope of theatre often constrained with limited budget and time for each production. However, when beginning to explore the intersection between engineering and theatre, it is found that the empirical nature of current theatrical practices can be countered, and scenic design and construction can be re-envisioned with engineering involvement …

Integrating Artificial Intelligence And Augmented Reality For Enhanced Task Performance In The Construction Industry, Aasish Chandrika Bhanu

All Dissertations

The Architecture, Engineering, and Construction (AEC) sector, characterized by its complex tasks, often faces challenges in adopting cutting-edge technologies, a trend that can significantly hinder productivity improvements compared to other industries. This dissertation explores the emerging integration of Artificial Intelligence (AI) and Augmented Reality (AR) within the AEC domain, investigating how effectively this can be implemented to potentially revolutionize industry practices. AI could be used in the AEC domain for advanced analytical and decision-making processes, while AR could be used for training, visualization, and remote collaboration.

In scenarios where construction site workers require expert guidance, these technologies could be helpful. …

Cardboard Concrete Column Formwork, Danny Shrestha, Joelle Schalesky

Architectural Engineering

This project is an exploration of cardboard as a potential material for construction formwork for concrete columns. Multiple material tests were conducted to explore the behavior of cardboard and concrete. Multiple specimens of cardboard were tested for modulus of elasticity, moment of inertia, and tensile strength. Concrete was tested for its apparent lateral fluid pressure under vibration. Cardboard formwork was then designed and constructed based on these tested behaviors. The final design of the formwork consisted of folding cardboard sheets lined with hardboard, supported by wood studs, and tied by plastic banding straps.

Ultimately, two concrete columns―8' and 10' in …

Natural Gas Induced Vegetation Stress Identification And Discrimination From Hyperspectral Imaging For Pipeline Leakage Detection, Pengfei Ma, Ying Zhuo, Genda Chen, Joel G. Burken

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Remote Sensing Detection of Natural Gas Leaks Remains Challenging When using Ground Vegetation Stress to Detect Underground Pipeline Leaks. Other Natural Stressors May Co-Present and Complicate Gas Leak Detection. This Study Explores the Feasibility of Identifying and Distinguishing Gas-Induced Stress from Other Natural Stresses by Analyzing the Hyperspectral Reflectance of Vegetation. the Effectiveness of This Discrimination is Assessed Across Three Distinct Spectral Ranges (VNIR, SWIR, and Full Spectra). Greenhouse Experiments Subjected Three Plant Species to Controlled Environmental Stressors, Including Gas Leakage, Salinity Impact, Heavy-Metal Contamination, and Drought Exposure. Spectral Curves Obtained from the Experiments Underwent Preprocessing Techniques Such as Standard …

Characterization Of Alkali-Silica Reaction (Asr) Products And C-S-H Using Swir Spectroscopy For Nondestructive Detection Of Asr, Pengfei Ma, Wenyu Liao, Ying Zhuo, Hongyan Ma, Yanping Zhu, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study explores the feasibility of characterizing alkali-silica reaction (ASR) products and calcium silicate hydrates (C-S-H) from short-wave infrared (SWIR) spectroscopy. ASR products and C-S-H samples with different Ca/Si ratios were synthesized and analyzed through XRD, 29Si nuclei magnetic resonance (NMR) and SWIR spectroscopy. Fourier-transform infrared spectroscopy (FTIR) was collected to help interpret the results from the SWIR spectroscopy. The obtained spectroscopic features were applied to quantify the ASR product abundance denoted by the length expansion of mortar bars after an accelerated ASR test. The results show that the SWIR spectra of the synthetic ASR gels are similar regardless of …

Digital Construction Annual Survey 2022 Report, Davitt Lamon, Ted Mckenna

Reports

The Annual Survey 2022 was conducted to assess the state of digital transformation in the Irish construction and built environment sector. This report presents the analysis of survey data, with a focus on implications for the Build Digital project and Build Digital’s five pillars: Digital Leadership & Cultural Change, Digital Standards, Digital Education & Training, Digital Procurement, and Sustainability & Circular Economy. Key findings from the survey indicated that a significant number of organisations have started their digital transformation journey, with many identifying themselves as proactive and possessing a clear business-focused strategy. However, a considerable cohort of respondents are keen …

International Information Management And Bim Best Practice Report, Ted Mckenna, Davitt Lamon

Reports

In order to inform the Digital Leadership and Cultural Change pillar of the Build Digital, a study of international best practice in digital adoption within the built environment sector globally was undertaken and is presented here-in. In order to identify key learnings for Ireland in the context of digital transformation, eight countries were included in this study, namely, Denmark, Finland, Netherlands, Germany, United Kingdom (UK), New Zealand, Australia and Singapore. These countries were selected for various reasons, including the level of digital maturity, the scale of the built environment sector and geographic spread. Key data for each country is included …

Sustainability And Circular Economy Horizon Scan And Needs Analysis, Sadaf Dalirazar, Mark Kelly, Derek Sinnott, James O'Donnell

Reports

The construction industry plays a crucial role in addressing the climate crisis as it is the largest global consumer of raw materials and contributes significantly to global energy consumption and emissions. Considering the world’s continuous population growth and the imperative to address infrastructure and housing demands the construction sector needs to adopt further sustainable strategies in its activities to reduce the pressure on natural resources. In addition, the Architecture, Engineering, and Construction (AEC) sector is responsible for generating substantial amount of waste known as Construction and Demolition Waste (CDW), which is projected to increase due to the future construction developments. …

Information Management And Bim Standards And Supports Inventory, Ryan Dempsey, Barry Mcauley, David Burke

Tools

The Digital Standards pillar consists of industry experts who champion the benefits of common rules, guidelines, and workflows that facilitate the improvement of information flow and information management across asset life cycles. Digital standards provide a common language that can be translated to technical specifications enabling clients, designers, contractors, and facilities managers, irrespective of their preferred tools, to communicate efficiently and reduce cost, rework, and disputes. Working closely with the Digital Procurement and Digital Education and Training pillars, this pillar is developing and delivering Irish Information Management/BIM (Digital Construction) guidelines for the sector.

This report summarises existing digital construction standards, …

Effect Of Type And Quantity Of Inherent Alkali Cations On Alkali-Silica Reaction, Pengfei Ma, Jiaoli Li, Jincheng Bai, Ying Zhuo, Lingyu Chi, Yanping Zhu, Zhenhua Shi, Hongyan Ma, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this study, the macroscopical expansion induced by alkali-silica reaction (ASR) and its corresponding ASR products are investigated using ordinary Portland cement (OPC) mortar specimens with a gradient of boosted alkalis. Experimental results show that the expansion increases with the concentration of inherent alkalis. Sodium-boosted samples expand approximately three times as much as potassium-boosted samples. ASR gels that are present in aggregate veins are calcium-free and amorphous; the atomic ratios of ASR gels are nearly independent of the type and quantity of alkali cations. Aggregate ASR gel exudation occurs in high (≥2.5 %) sodium cases and produces potential Na-shlykovite. Crystalline …

Meta-Analysis Of Insulated Concrete Wall Panel Design Methods For Shear And Flexure Behavior, Maryam Al-Bayati

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

Insulated Concrete wall panels have been designed and constructed since the early 1950s with various shear ties, dimensions, and methods; nonetheless, thermal bridging and rational design are still a concern. Many companies have recently developed plastic connectors that have gradually replaced solid concrete sections and steel connectors due to their superior thermal efficiency and strength. However, there is no generally accepted method for predicting the behavior of sandwich wall panels in structural engineering practice or codes, but many methods have been used since the early 1920. This study aims to evaluate the accuracy of current methods for predicting the flexural …

An Investigation Into Ireland’S Bim Skills Gap, Guadalupe Centanni, Barry Mcauley

Conference Papers

The adoption of digital skills within the Irish AEC Sector has the potential to enhance efficiency and competitiveness among its stakeholders. Despite this opportunity, there is still a high demand for skilled BIM professionals, which cannot be currently met. To meet this skills demand and directly target future skills gaps within Ireland, several challenges must be addressed to facilitate broader BIM adoption. This paper focuses on addressing this gap by identifying steps to be followed to develop skilled professionals within BIM. This has been achieved by investigating the extent to which construction stakeholders in Ireland comprehend BIM and, examiningthe training …

Accelerating Bim Adoption In Ireland: A Ten-Year Review Of Cita Bim Gathering Proceedings, Alan Hore, Roger West, Barry Mcauley

Conference Papers

Digital construction interfaces have been studied extensively over the last few decades, with an ever-grow- ing catalogue of publications. The CitA BIM Gathering conferences have played a key role in bringing together the research and industry communities ina collaborative setting over the past decade in Ireland. In this paper the authors systematically review 10 years of papers published in the BIM Gathering pro- ceedings since the inaugural conference in 2013. A total of 175 papers involving over 200 authors have been reviewed and classified under the 2018 World Economic Forum (WEF) recommendations in respect to ac- celerating BIM adoption. The …

Industry Colloquium Report, Robert Moore

Reports

In the ever-evolving landscape of the construction industry, digital transformation has emerged as a pivotal force reshaping the way projects are conceived, executed, and delivered. This transformation, fuelled by cutting-edge technology and innovative practices, holds the promise of greater efficiency, sustainability, and collaboration within the construction sector.

This report offers a comprehensive summary of the Build Digital Project colloquium. It provides actionable insights and recommendations for clients, supply chain partners, and for prioritisation within the Build Digital Project pillars. As the industry partners seek to build a more efficient, sustainable, and collaborative construction sector, understanding and harnessing the invaluable insights …

Skills Matter – Up-Skilling Across Construction Stakeholders For Emerging Roles, Avril Behan, Paul Mccormack, Barry Mcauley

Conference Papers

The EU’s Climate Target Plan To 2030 (European Union 2020b) of achieving at least 55% reduction in Green House Gas emissions from 1990 levels, delivering towards a climate-neutral economy by 2050, requires systems-level change in the way we design, construct, and operate our built assets. Funding initiatives, such as co-ordinated by BUILD UP Skills, aim to deliver upskilling to the market but targets set by the European Skills Agenda may not be reached at current achievement levels. This paper presents the results of one completed and the progress of one ongoing Horizon 2020 funded project, BIMcert and ARISE, respectively. Learning …

Development And Characterization Of Coal-Based Thermoplastic Composite Material For Sustainable Construction, Haibin Zhang, Wenyu Liao, Genda Chen, Hongyan Ma

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The exploitation of coal and the disposal of waste plastic present significant environmental and economic challenges that require sustainable and profitable solutions. In response, we propose a renewable construction composite material of coal-based thermoplastic composite (CTC) that can be made from low-grade coal and plastic waste. We developed and tested the hot-press fabrication method for this CTC, using coal with a maximum particle size of 4.75 mm and recycled high-density polyethylene (HDPE). The effects of the coal fraction (50–80 wt.%) on compressive properties, thermal properties, microstructure, and ecological and economic efficiencies of the CTC were investigated. Test results revealed that …

Machine Learning-Based Seismic Damage Assessment Of Residential Buildings Considering Multiple Earthquake And Structure Uncertainties, Xinzhe Yuan, Liujun Li, Haibin Zhang, Yanping Zhu, Genda Chen, Cihan H. Dagli

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Wood-frame structures are used in almost 90% of residential buildings in the United States. It is thus imperative to rapidly and accurately assess the damage of wood-frame structures in the wake of an earthquake event. This study aims to develop a machine-learning-based seismic classifier for a portfolio of 6,113 wood-frame structures near the New Madrid Seismic Zone (NMSZ) in which synthesized ground motions are adopted to characterize potential earthquakes. This seismic classifier, based on a multilayer perceptron (MLP), is compared with existing fragility curves developed for the same wood-frame buildings near the NMSZ. This comparative study indicates that the MLP …

A Spike-Shaped Anchorage For Steel Reinforced Polymer (Srp)-Strengthened Concrete Structures, Xingxing Zou, Keenan L. Mcburney, Lesley H. Sneed

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Steel reinforced polymer (SRP) composite has recently emerged as an effective and economical solution for strengthening of reinforced concrete (RC) structures. Premature debonding failure of unanchored SRP at low load levels generally governs the performance of RC structures strengthened with externally bonded SRP. Therefore, a novel yet simple spike-shaped anchorage system was proposed in this study to prevent the debonding failure of SRP and to improve the interfacial shear capacity. Experimental investigation through single-lap shear tests of SRP-concrete joints showed that the anchorage system changed the failure mode from composite debonding to fiber rupture. In addition, the anchorage system substantially …