Architectural Engineering Commons^™

Assessment Of Advanced Glazing Systems For Building Energy Efficiency In Hot-Arid Climates, Ahmad I. Elshamy, Yousef Elgefly, Yara El-Metwally, Serag Salem

Architectural Engineering

The built environment is considered among the most contributing factors to energy consumption. The building envelope plays a crucial role in determining the building energy consumption, regulating heat transfer and maintaining adequate indoor environmental quality. Hence, optimizing the thermal performance of the building envelope by achieving optimal glazing solutions while fulfilling the Sustainable Development Goal (SDG 7) is the main aim of this research. This study investigates the impact of various facade glazing systems on the building energy performance, focusing on the cooling energy consumption of an office building in a hot arid climate, Cairo, Egypt. The novelty of this …

Large-Scale Experimental Study On The Impact Of Air Cleaning & Ventilation On Indoor Air Quality And Student Illness-Related Absenteeism, Daud Nosham

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

This large-scale randomized experimental field study investigated the effect of portable air purifiers (PAPs) on classroom’s air quality and student’s illness related absenteeism. PAPs were installed in 317 classrooms from various school districts located in Eastern Nebraska. The classrooms were randomly assigned into four conditions: three treatment conditions (T1, T2 & T3) and one control condition (device without any filter). T1 was equipped with HEPA filters, T2 added Activated Carbon (AC) layer to HEPA, and T3 further integrated Germicidal Ultraviolet (GUV) alongside HEPA and AC filters. The measured variables were carbon dioxide (CO2), fine particles (PN2.5) and coarse particles (PNcoarse), …

Introduction To Building Energy Modeling And Analysis Using Energyplus, Jackson C. Burnett

Mechanical Engineering Undergraduate Honors Theses

Retail stores are dynamic environments where human activities significantly influence energy consumption patterns, particularly affecting heating, ventilation, and air conditioning (HVAC) demands. Existing energy models, such as those developed using EnergyPlus, often rely on generalized assumptions about human occupancy and behavior, leading to discrepancies between predicted and actual energy usage. This research aimed to enhance the accuracy of energy modeling for retail stores by conducting a sensitivity analysis of occupancy using EnergyPlus simulations. The study investigated how variations in occupancy levels impact HVAC loads, cooling and heating demands, and overall energy use. Results showed that increasing occupancy leads to higher …

Building Resilience: Strategies For Sustainable Wildfire Management In California, Jaiden Rennie, Pegah Zamani

Symposium of Student Scholars

Wildfires in California are becoming more intense and destructive, threatening communities, ecosystems, and livelihoods. This project explores how resilience and sustainability can work together to reduce wildfire risks and long-term damage. By reviewing research, case studies, and expert insights, it examines what’s driving these fires, climate change, poor land management, and human activity, and looks at solutions that can make a real difference. From community education programs to AI-driven fire detection and smarter policies, the findings highlight practical ways to better prepare for and manage wildfires. The goal is to contribute to a future where communities and the environment are …

Evaluating Energy Efficiency And Thermal Performance In Egypt’S Social Housing: Climate-Responsive Design And Material Impact In Hot Desert Environments, Ahmed M. Hanafi, Mohamed A. Moawed, Osama E. Abdullatif

Journal of Engineering Research

As Egypt's urban areas expand rapidly, the demand for energy-efficient, affordable housing in extreme hot desert climates has become increasingly urgent. This study investigates the energy efficiency and thermal performance of Egypt’s Social Housing Project, with a focus on residential building in New Aswan City, where summer temperatures frequently exceed 45°C. Employing a validated energy model, this research simulates annual energy consumption for the building, which comprises 24 residential units, each approximately 86 m². The model integrates realistic occupancy schedules, region-specific weather data, and common household behavior patterns to closely reflect actual energy usage. Findings indicate a high alignment between …

Seismic Resilience Of Timber Homes, Melia R. Costa

College of Engineering Summer Undergraduate Research Program

The vast majority of residential buildings in California are wood-frame structures. A home is typically a very large investment for families, and damage to the home can be detrimental to a family’s economic success. Thus, reducing the economic impacts of an earthquake on residential timber housing is crucial. A full scale, two-story section of a residential timber house is in construction in the Parson’s Geotechnical and Earthquake Engineering Laboratory on the Cal Poly campus in San Luis Obispo, California. Once built it will be put through earthquake simulation tests on a shake table with various magnitudes of seismic activity. Next, …

In Situ Synthesis, Characterization And Photocatalytic Efficacy Of Silver-Enhanced Mxene And Graphene Nanocomposites, Kishore Chand, M. Mustafa Azeem, Muhammad Nazim Lakhan, Mukhtiar Ahmed, Muhammad Jehanzaib Aslam, Ahmer Hussain Shah

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The emergence of 2D materials has significantly expanded the wide range of nanomaterials with diverse applications. Notably, their high conductivity, catalytic efficiency, and hydrophobicity have fueled heightened research interests for water treatment applications. This research aimed to investigate the synthesis and characterization of MXene and reduced graphene oxide (rGO) nanocomposites with silver nanoparticles (Ag) for enhanced catalytic activity in the decomposition of Direct Blue-24 dye. In this study, we employed well-established methods, previously documented in the literature, to prepare two distinct nanocomposites. Novel nanocomposites, namely reduced graphene oxide–silver nanoparticles (rGO–Ag) and MXene–silver nanoparticles (MXene–Ag), were synthesized using the hydrothermal and …

In Situ Synthesis, Characterization And Photocatalytic Efficacy Of Silver-Enhanced Mxene And Graphene Nanocomposites, Kishore Chand, M. Mustafa Azeem, Muhammad Nazim Lakhan, Mukhtiar Ahmed, Muhammad Jehanzaib Aslam, Ahmer Hussain Shah

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The emergence of 2D materials has significantly expanded the wide range of nanomaterials with diverse applications. Notably, their high conductivity, catalytic efficiency, and hydrophobicity have fueled heightened research interests for water treatment applications. This research aimed to investigate the synthesis and characterization of MXene and reduced graphene oxide (rGO) nanocomposites with silver nanoparticles (Ag) for enhanced catalytic activity in the decomposition of Direct Blue-24 dye. In this study, we employed well-established methods, previously documented in the literature, to prepare two distinct nanocomposites. Novel nanocomposites, namely reduced graphene oxide–silver nanoparticles (rGO–Ag) and MXene–silver nanoparticles (MXene–Ag), were synthesized using the hydrothermal and …

Spatial Hearing In Simulated Reverberant Classroom Environments, Gabriel Seth Evan Weeldreyer

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

Spatial hearing provides access to auditory spatial cues that promote speech perception in noisy listening situations. However, reverberation degrades auditory spatial cues and limits listeners’ ability to utilize these cues for segregating target speech from competing babble. Hence, spatial unmasking—an intelligibility benefit from a spatial separation between a target and masker—is reduced in reverberant environments as compared to free field. This work tests the hypothesis that interaural decorrelation, the result of increasing reverberation, will broaden the perceived auditory source width with a cascading effect of reduced auditory spatial acuity and subsequently poorer spatial unmasking. To understand the perceptual consequences of …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Beneficiation Of Lunar Regolith Simulants Through Electrostatic Sieving And Magnetic Separation, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

In the light of future development of lunar structures, in-situ feldspar beneficiation is imperative for metal extraction. This research incorporates the tandem use of electrostatic sieving and magnetic separation for collecting a specific size range and mineral composition from lunar soil that optimizes subsequent chemical processing. While earlier works focused on silt-sized particles, this work expands that range up to medium-grained sand with a greater variety of potential lunar regolith compositions. This work shows that a 2.5 kV, 7 Hz to 30Hz frequency, single-phase square wave can lift silt and fine sand for collection. This lifting is successful directly from …

Kinetic Modeling Of Electrostatic Sieving For Lunar Regolith Beneficiation: Case Studies, Easton Ingram, Emmanuela Amen Eze, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith particles with applications to the concept of electrostatic sieving. The new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. Case studies for a concept of electrostatic sieving were chosen to validate the new model. The simulation achieved similar yields reported in previous works, which served as validation of the model. The new model is computationally efficient and could serve as a design, analysis, and optimization tool.

Effect Of A Geothermal Heat Pump System On Cooling Residential Buildings In A Hot, Dry Climate, Rania Rushdy Moussa, Ayman H. Mahmoud

Architectural Engineering

ABSTRACT In the last century, electricity demand has doubled due to urban expansion, which has contributed to the formation of more urban heat islands (UHI) and the appearance of environmental hazards such as the global climate change phenomenon. Since residential buildings are considered the main electricity consumer sector in Egypt, they consume up to 42% of total energy consumption, which contributes to increasing temperatures and constitutes UHI in cities. In this context, the research aims to examine the effectiveness of using the closed vertical loop geothermal system (GSHPCV) for cooling residential buildings in a hot, dry climate, such as Cairo, …

Atomic Insights Into The Structural Properties And Displacement Cascades In Ytterbium Titanate Pyrochlore (Yb2ti2o7) And High-Entropy Pyrochlores, M. Mustafa Azeem, Qingyu Wang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Pyrochlore oxides ((Formula presented.) are potential nuclear waste substrate materials due to their superior radiation resistance properties. We performed molecular dynamics simulations to study the structural properties and displacement cascades in ytterbium titanate pyrochlore ((Formula presented.)) and high-entropy alloys (HEPy), e.g., (Formula presented.), (Formula presented.), and (Formula presented.). We computed lattice constants (LC) ((Formula presented.)) and threshold displacement energy (Ed). Furthermore, the calculation for (Formula presented.) and ionic radius ((Formula presented.)) were performed by substituting a combination of cations at the A and B sites of the original pyrochlore structure. Our simulation results have demonstrated that the lattice constant is …

Healthcare Built Environment And The Covid-19 Pandemic, A Mixed-Method Study, Mohammad Saleh Nikooopayan Tak

All Theses

The outbreak of COVID-19 presented an unparalleled risk to public health, leading to urgent scientific efforts in understanding transmission mechanisms and mitigating risks, especially in healthcare settings. This mixed-methods study examines knowledge advancement regarding indoor air quality in healthcare facilities during the pandemic. A systematic literature review of 163 post-COVID studies identifies key research thrusts and 31 recommendations related to building ventilation, air filtration, surface disinfection, and monitoring. Comparison with over 200 pre-pandemic publications reveals both reliance on established infection control principles and unique contributions, such as detecting viral RNA in air and surface samples indicating potential airborne and fomite …

On The Development Of Part-Scale Fem Modeling For Laser Powder Bed Fusion Of Aisi 316l Stainless Steel With Experimental Verification, Muhammad Arif Mahmood, Asif Ur Rehman, M. Mustafa Azeem, Abedalkader Alkhouzaam, Marwan Khraisheh

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In laser powder bed fusion (LPBF), the effects of operating conditions on thermal gradients and residual stresses are the utmost challenges that require significant attention. The magnitudes of residual stress in the printed layers, as well as the distribution along the printed components, have not been well explained for LPBF parts. In this study, a 3D finite element thermo-mechanical model has been established to investigate the effect of operating conditions on thermal distribution, melt pool evolution, residual stress distribution, and part distortion. The printed AISI 316L stainless steel cubes have been characterized experimentally. The results showed a proportional correlation among …

Addressing Low Heat Pump Heating System Sales In The Uk, Ben Costelloe

Articles

The replacement of existing fossil fuel boilers with heat pumps is seen as a key measure in the decarbonisation of heating systems and addressing climate change. This policy however, is currently failing in many Western European states, particularly in the UK. The many reasons for this situation are examined. However, the age of UK housing stock and particularly the high number of dwellings built prior to the introduction of building insulation regulations in 1980, are key. To maintain the running cost of air source heat pumps competitive with those of the gas boilers they generally replace the heat pump lift …

The Center For Centering Dome, Olek Piechaczek, Ryan M. Scharf

Architectural Engineering

The Center for Centering seeks to create a large-scale healing center, conducive to individual centering of the mind and body. This mobile installation provides a relaxing, enclosed space while still maintaining a connection to the outdoors. The clients liked the idea of having a pop-up installation that could be easily set up as a touring display. With a deadline for installation looming in June 2022, a team of students had five months to design and manufacture the structure.

In winter 2022, the students developed custom geometry to minimize the number of individual parts and built a ¼ scale model of …

Sky Survey Radio Telescope, Jack E. Mcguigan

Electrical Engineering

This document outlines the design of a radio telescope designed to perform hydrogen line sky surveys. The telescope produces radio images mapping the intensity and relative velocities of hydrogen concentrations to their sky coordinates. Over the course of a day, the telescope images the regions of space visible to it, allowing sky survey imagery to be updated daily. Sky survey images are comprised of an array of pixels corresponding to specific sky coordinates. Each 8-bit RGB pixel contains information on the concentrations of hydrogen in the brightness and relative velocity in the color. Radio images mapping the concentrations and velocities …

Using Bim To Increase The Efficiency Of Energy-Driven Retrofitting Projects, Anne Grego, Shannon Chance, Barry Mcauley

Conference Papers

The building sector is responsible for nearly 40% of global energy consumption. Many existing buildings have poor thermal insulation and low energy performance, hindering sustainability goals. Energy-driven building retrofitting could address this issue and implementing Building Information Modelling (BIM) in retrofitting can reduce process time, costs, and waste associated with such undertakings. Yet, there is a lack of research and insufficient guidance for implementing BIM in energy-driven retrofitting. A BIM framework is presented to enhance decision-making processes during retrofitting. The aims of this study were to (1) identify BIM technologies and methodologies that could address existing barriers and improve efficiency …

Characterizing Energy Dissipation Of Shallow-Water Wave Breaking In A Storm Surge, Hunter Boswell, Guirong Grace Yan, Wouter Mostert

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

While understanding breaking waves is crucial for the development of parametrizations used in ocean wave modeling for both deep and shallow water, the complete process of wave breaking is not well understood. Here we present direct numerical simulations of two-dimensional solitary waves that shoal and break on a uniform beach in shallow water, with the presence of storm surge represented by an inshore region. The storm surge depth, beach slope, and wave amplitude are varied to study the dependence of energy dissipation in the breaker on wave and bathymetric parameters. We classify wave breaker types and find a separation between …

Lunar In-Situ Aluminum Production Through Molten Salt Electrolysis (Lisap-Mse), Jacob Ortega, Jeffrey D. Smith, Fateme Rezaei, David Bayless, William P. Schonberg, Daniel S. Stutts, Daoru Frank Han

NASA-Missouri Space Grant Consortium

The goal of Artemis is to establish a sustained presence on the Moon. To achieve so, numerous resources are necessary. The Moon contains several essential elements needed to sustain human presence. Most of those elements are trapped in the form of minerals. To refine those minerals into useful materials, reduction methods are needed. Most reduction methods on Earth require large amounts of mass and power which is unrealistic for early stages of building a lunar base. To solve this problem, we are developing a concept of Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE).

The LISAP-MSE project, if successful, …

An Insight Into The Effect Of Sharp And Round Edges On The Flow Field-A Cfd Simulation, Abid Hussain, Gao Puzhen, M. Mustafa Azeem, Muhammad Zubair, Muhammad Aamir, Muhammad Irfan Khaleed

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents a numerical investigation of pressure drop and distribution in a channel around a sharp edge and a disc that is connected to the base of a circular rod. We have employed computational fluid dynamics (CFD)-Fluent for the validation of our models. It was found that the edge sharpness of the disc influences the pressure drop., i.e. sharp edge has higher turbulence and pressure drop. We also observed that pressure drops in the case of the circular disc are less than that of the sharp edge. However, pressure drop has essentially the same values for both shapes after …

Nucleotide Detection Mechanism And Comparison Based On Low-Dimensional Materials: A Review, M. Mustafa Azeem, Muhammad Shafa, Muhammad Aamir, Muhammad Zubair, Basma Souayeh, Mir Waqas Alam

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The recent pandemic has led to the fabrication of new nucleic acid sensors that can detect infinitesimal limits immediately and effectively. Therefore, various techniques have been demonstrated using low-dimensional materials that exhibit ultrahigh detection and accuracy. Numerous detection approaches have been reported, and new methods for impulse sensing are being explored. All ongoing research converges at one unique point, that is, an impetus: the enhanced limit of detection of sensors. There are several reviews on the detection of viruses and other proteins related to disease control point of care; however, to the best of our knowledge, none summarizes the various …

Use Of Precious Plastic Method Of Bricks For The Construction Of Tiny Homes, Haylie E. Tallon

Architectural Engineering

Precious Plastics, a Netherlands based company, created an open source project that can be used to create different objects from recycled plastics. The San Luis Obispo area has a large amount of recyclable plastic that is being treated as trash, adding to the pollution of the ocean and the air. This project is to determine the necessary steps to create plastic building blocks, using the Precious Plastic process, as a construction material for low-income, temporary housing. This report covers the process that was used to build two of the machines that will be used to create the bricks. This requires …

New Mathematical Models For Acoustic Insertion Loss Of Fiberglass Lining In Hvac Duct, Michael Anthony Schwob

UNLV Theses, Dissertations, Professional Papers, and Capstones

The design objectives for HVAC air distribution systems are thermal comfort, good indoor air quality, energy efficiency, low construction cost, and appropriate indoor noise levels. The last objective requires that the designer can predict the attenuation of sound transmitted through an air duct. One form of attenuation commonly introduced to an air distribution system to achieve interior noise criteria is fiberglass liner. Past research has been conducted to obtain reliable and accurate insertion loss (IL) data for duct with fiberglass liner. Empirical efforts have relied on limited data sets. Computational efforts have produced numerical models that are not practical for …

Strategic Energy Master Planning For Carbon Neutrality, Marie Patterson

CSU Journal of Sustainability and Climate Change

Universities across the United States are generating goals to be more sustainable and carbon neutral. The energy used in existing buildings on campuses amount to a large volume of greenhouse emissions and must be reduced to help achieve neutrality goals. Strategic Energy Master Plans are instrumental to support these goals through the development of recommendations to reduce energy. Calculating the energy use intensity for existing buildings, a main component of a Strategic Energy Master Plan, can help the campus understand where energy is being used the most. With this information the highest energy consuming buildings can be the focus of …

Transdisciplinarity In Experience Design: A Global Survey Of Higher Ed Programs In Exd/Xd, Yvonne Houy

Creative Collaborations

In our age of ubiquitous devices and digital media it is the perceived value of the end-to-end experience that brings people to a place. Designing inspiring and emotionally engaging end-to-end experiences requires experts in a wide range of disciplines committed to an interdisciplinary collaboration that can arrive at transdisciplinary design - the sum becomes greater than its parts.

Civil engineering, hospitality, business, psychology, digital User Experience (UX) design, and experience data analysis need to be seamless integrated with the fine and performing arts and design fields:

• Architecture, interior, landscape and sound design actively engage the senses.

• Graphic and fine arts …

  ---

  Go to article

Building Performance - Societal Drive, Programme And Symposium, Joseph Little, Patrick Daly

Articles

Society is increasingly looking at the construction industry to mitigate the environmental crisis and solve the housing crisis through wholesale embrace of three broad sets of challenges. The MSc in Building Performance (Energy Efficiency in Design) (MSc BP(EED)) was created in 2017 to provide significant upskilling in the knowledge, skills, and software applications of building design professionals so that they can meet these challenges, while creating compliant, sustainable, super-low energy, new and renovated buildings. The delivery of the programme supports upskilling of employed building design professionals at Masters level, encouraging a minority to develop their capacity and interest in research …

Investigation Of The Prevalence Of Faults In The Heating, Ventilation, And Air-Conditioning Systems Of Commercial Buildings, Amir Ebrahimifakhar

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

This dissertation describes a large-scale investigation of heating, ventilation, and air-conditioning (HVAC) fault prevalence in commercial buildings in the United States. A multi-year dataset with 36,556 pieces of HVAC equipment including air handling units (AHUs), air terminal units (ATUs), and packaged rooftop units (RTUs) was analyzed to determine values for several HVAC fault prevalence metrics. The primary source of data for this study comes from three commercial fault detection and diagnostics (FDD) providers. Since each FDD provider uses different terms to refer to the same fault in an HVAC system, a mapping function was created for each FDD provider’s dataset, …