Architectural Engineering Commons^™

Common Ground Newsletter Fall 2026, Missouri University Of Science And Technology

Common Ground

- Q&A Experiences

- Shaping the next generation

- Chi Epsilon earns four awards

- Summer Camps

- Design Team Results

Field Calibration Of Flow Over Tilting Weirs In Canals, Joseph E. Pugh, Timothy K. Gates, S. Karan Venayagamoorthy, Caner Kutlu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Tilting weirs are widely used to regulate water levels in open channel irrigation systems and can also provide flow measurement capability that helps optimize irrigation efficiency and ensure equitable water distribution. This case study demonstrates adaptation of lab-based tilting weir ratings to field settings, where flow behavior is more complex. We compile and analyze an extensive data set derived from independent studies of five structures within three canal systems, featuring both lined and unlined channels with discharge ranging from 0.35 to 15 m3/s (12 to 530 ft3/s). Results indicate that lab-based rating equations can be calibrated to account for site-specific …

Effect Of Rheology Modification On Fiber Orientation And Dispersion In 3d-Printed Ultra-High-Performance Concrete, Haodao Li, Alfred Addai-Nimoh, Seongho Han, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The extrusion process in 3D concrete printing (3DCP) facilitates horizontal alignment of steel fibers along the printing direction, thus enhancing the load-bearing capacity of printed elements. However, such shear-induced fiber alignment is highly sensitive to rheological properties. This study investigates how variations in dynamic yield stress (τd) and plastic viscosity (μ), influence the extrudability, fiber orientation and dispersion, and anisotropic mechanical behavior of ultra-high-performance concrete (UHPC). Five viscosity-modifying agent (VMA) types were incorporated at two content levels to modify the rheology of printable UHPC. Results showed that moderate VMA additions improved printability, whereas excessive contents markedly increased τd and μ; …

Transforming Dredged Sediment Into Reactive Clay: Critical Review Of Calcination, Reactivity, And Sustainable Valorization As Supplementary Cementitious Material, Seongho Han, Sanghwon Wi, Koochul Ji, Keun Hyeok Yang, Farshad Rajabipour, Kamal H. Khayat, Jinyoung Yoon

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Dredged sediment (DS) is generated worldwide in large volumes through routine port and waterway maintenance, yet its disposal presents environmental and economic challenges. Recently, calcined dredged sediment (CDS) has emerged as a supplementary cementitious material (SCM), offering a viable alternative to traditional SCMs, such as fly ash and slag cement. This review synthesizes current knowledge on the physical, chemical, and mineralogical characteristics of raw DS and pretreatment strategies aimed at dewatering, organic matter removal, and contaminant stabilization. The effects of calcination on the production of reactive amorphous aluminosilicates are also discussed. Emphasis is placed on physicochemical changes revealed by experimental …

Design And Implementation Of A Honeycomb Damping System For The 2026 Eeri Seismic Design Competition, Vera Nguyen, Lauryn Wojcik

Architectural Engineering

The authors of this report were a part of the 2026 Earthquake Engineering Research Institute (EERI) chapter at California Polytechnic State University, San Luis Obispo. In July 2026, they will travel to Portland, Oregon with 12 students to compete in the Undergraduate Seismic Design Competition hosted by EERI. The competition required teams to develop a comprehensive structural design proposal that included computer-based modeling and analysis, construction of three physical models, and the preparation of both a technical poster and oral presentation for a proposed high-rise building located in Portland, Oregon. Cal Poly’s “Illahee Tower” was designed with an emphasis on …

Concrete And Masonry Code (Beams), Michael Alexander Simas Rocha

Architectural Engineering

This report only covers the beam design of the code that was written. The end goal of this project is to write code for concrete and masonry following what was taught in the lecture classes. This project is acting as a foundation for the end goal of a program that can compete with SAP2000, ETABS, RISA, and others. One final goal is to have the print out have the look and feel of having been done by hand. While coding; several factors were recorded including time spent coding, debugging, and then to do three problems by hand vs how long …

Domain-Specific Design On Fpga And Npu For Scientific Computing And On-Device Llm Inference, Miaoxiang Yu

All Dissertations

High-performance computing (HPC) is changing rapidly as scientific simulations and large language model (LLM) workloads push the need for higher performance under tight power and memory constraints. Conventional platforms such as CPUs and GPUs accelerate computation through instruction-driven parallelism, relying on multithreading, SIMD, and SIMT execution, but increasingly encounter scalability limits imposed by the power and memory walls. In contrast, Field-Programmable Gate Arrays (FPGAs) and Neural Processing Units (NPUs) offer a high-efficiency alternative through dataflow-oriented architectures that exploit deep pipelining and customized memory hierarchies to reduce data movement. However, the performance potential of these spatial accelerators remains largely unrealized when …

Indirect Carbonation Of Fbc Ash For Sustainable Production Of Caco3 And Reactive Pozzolanic Residues, Suhawn Ju, Heejung Jun, Seongho Han, Minseok Kim, Soohyun Song, Mingi Cho, Sukhoon Pyo, Jinyoung Yoon

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study investigates the potential of indirect carbonation for CO₂ sequestration and high-purity CaCO₃ production using fluidized bed combustion (FBC) fly ash (FFA) and bottom ash (FBA). XRF and XRD analyses revealed high reactive CaO contents derived from lime, portlandite, and anhydrite. Calcium extraction using 1- mol NH₄Cl achieved markedly higher efficiency than deionized (DI) water, yielding up to 17,586 mg/L of Ca²⁺ and producing 10.2 wt.% and 8.4 wt.% CaCO₃ from FFA and FBA, respectively, with CO₂ capture capacities of 45.0 and 36.8 kg per ton of ash. The precipitated CaCO₃ exhibited …

Propagation And Interaction Of Gravity Currents Induced By Successive Release Of Two Lock Fluids, Khem Prasad Bhattarai, Subhas Karan Venayagamoorthy

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study investigates the dynamics of sequentially released gravity currents in a lock-exchange configuration consisting of two lock fluids using high-resolution numerical simulations and compares them with the classical single-lock exchange. The results demonstrate that, in a two-lock-fluid configuration, the overtaking of the lighter lock current by the heavier lock current alters the current's front dynamics, leading to complex velocity transitions. Before overtaking occurs, the front propagation is slower than in the classical single-lock-fluid case because of lower density contrast, but after overtaking, the heavier lock fluid accumulates at the head region of the current and enhances its speed. The …

Methodology For Surface Defect Assessment In 3d Concrete Printing Using Computer-Vision And Ultrasonic Testing Considering Structural Build-Up, Seongho Han, Eunjong Ahn, Myoungsu Shin, John S. Popovics, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study quantifies how interlayer time gaps and mixture rheology jointly influence interfacial integrity and mechanical performance in 3D concrete printing (3DCP). Two mixtures incorporating identical binders, but differing limestone fineness (4 and 50 μm) were printed with interlayer delays of 0, 2, and 5 min, corresponding to stacking rates of approximately 9, 0.5, and 0.2 m/h. The finer limestone mixture exhibited higher plastic viscosity (13.2 vs. 11.5 Pa s) and faster structural buildup (58 vs. 38 Pa/min), resulting in accelerated early stiffening. Deposition yield stress derived from buildup measurements remained low for 0–2 min (1400–1500 Pa for the higher-thixotropy …

Impact Of Femalized Kinesthetic Learning Model On African American Middle School Girls’ Career Interest, Mercy F. Fash, Andrea Ofori-Boadu

Journal of Global Education and Research

Engaging African American middle school girls in out-of-school-time (OST) Architecture, Engineering, and Construction (AEC) programs can boost interest in male-dominated AEC careers. This study adopts Lent’s Social Cognitive Career Theory to evaluate the impact of an OST feminized AEC kinesthetic learning model (fAEC-KLM) on the career interests of this demographic. Through a qualitative research approach, fourteen (14) African American middle school girls from Guilford County, NC, completed pre- and post-interviews on how fAEC-KLM interactions influenced their AEC career interests. Inductive thematic analysis was carried out on transcribed interviews. Results show that effective components, such as lectures on AEC, bridge construction …

Rheological Modification Of Alkali-Activated Slag Mortar: Roles Of Sodium Gluconate Retarder And Dispersants, Tae Yong Shin, Seongho Han, Ryong You, Yubin Jun, Jae Hong Kim

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Alkali-activated materials have emerged as promising low-carbon alternatives to ordinary Portland cement-based binders; however, their practical application is strictly limited by rapid setting and poor workability. To address these challenges, this study proposes an evaluation methodology combining setting time measurement, cloud point tests for chemical stability, and wide-range rheological analysis. While conventional superplasticizers like polycarboxylate ether (PCE) proved unstable in high-alkaline environments, cloud point tests revealed that polynaphthalene sulfonate (PNS) and butyl acrylate (BA) exhibited superior chemical stability. Notably, BA was identified as a novel and effective dispersant in 3.5 M KOH-activated systems, reducing yield stress of fresh mortar by …

Utilization Of Plastic Waste In The Concrete Industry, Nancy Abdelmoneim Sakr

Theses and Dissertations

Plastic recycling has emerged as a crucial strategy that aligns with environmental, social and economic sustainability indicators. Currently, substantial volumes of plastic waste are either deposited in landfills or incinerated, neglecting the potential to harness its embodied energy and the energy consumed for producing virgin materials. A key advantage of plastic lies in its promising mechanical properties. Concrete mix design is fundamental to a wide range of construction applications, including brick walls, reinforced concrete slabs and concrete pavements. Despite the adoption of recycled plastic in construction materials in various countries, its widespread implementation remains limited. This is primarily due to …

Influence Of Co2 Curing On Carbonation Depth, Phase Composition, And Micro-Mechanical Properties Of Fbc Ash-Blended Cementitious Materials, Heejung Jun, Seongho Han, Sanghwon Wi, Jinyoung Yoon

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study investigates the physicochemical and mechanical performance of cementitious composites incorporating fluidized bed combustion (FBC) ash under accelerated carbon dioxide (CO₂) curing. FBC ash, due to its high contents of free calcium oxide (CaO) and sulfate (SO₃), has been reported to cause challenges, such as volume instability and lower early-age strength. To address these limitations, CO2 curing was applied to promote accelerated carbonation and stabilize the hydration products. Cement paste and mortar samples, made with up to 40 % by cement weight replacement with FBC ash (labelled CF), were subjected to either CO₂ curing …

Assessment Of Advanced Glazing Systems For Building Energy Efficiency In Hot-Arid Climates, Ahmad I. Elshamy, Yousef Elgefly, Yara El-Metwally, Serag Salem

Architectural Engineering

The built environment is considered among the most contributing factors to energy consumption. The building envelope plays a crucial role in determining the building energy consumption, regulating heat transfer and maintaining adequate indoor environmental quality. Hence, optimizing the thermal performance of the building envelope by achieving optimal glazing solutions while fulfilling the Sustainable Development Goal (SDG 7) is the main aim of this research. This study investigates the impact of various facade glazing systems on the building energy performance, focusing on the cooling energy consumption of an office building in a hot arid climate, Cairo, Egypt. The novelty of this …

Bond Behavior Of Full-Scale Beams Using Sustainable Self-Compacting Concrete, Hayder H. Alghazali, Atheer H.M. Algburi, John J. Myers

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Sustainable concrete is a step towards greener and more eco-friendly concrete construction practices, helping to solve global environmental problems. The present study focuses on the bond behavior between steel reinforcement and greener self-compacting concrete, specifically sustainable self-compacting concrete (SUS-SCC). Three SUS-SCC mixtures with different fly ash (FA) to cement replacement levels of [50, 60, and 70% (by mass)] were developed. Twelve full-scale SUS-SCC beams with a cross-section of (305 x 57) mm and a total length of 3048 mm were cast and tested using a four-point load test setup. The effect of longitudinal and lateral steel reinforcement ratios in the …

Nonlinear Flow Structures From The Interaction Of Internal Waves With Topography, Matthew R. Klema, S. Karan Venayagamoorthy

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents numerical simulations of the interaction of first-mode internal waves with a topographic edge at the intermediate scale, O (100) m, with a focus on the evolution of flow structures. Flow structure variation and evolution is explored through direct modifications to the amplitude of the internal wave interacting with topographic features of varying wave-topographic slope (g/s), height of the topography to the total domain depth (ht/d), and the wave Froude number (Fr = U0/cph), where g is the internal wave slope, s is the topographic slope, ht is the height of the topography, d is the simulation depth, …

Rapid State-Of-Health Estimation Of Batteries Using Machine Learning With Limited Eearly-Discharge Voltage Data, Mohammad Bakhtiari

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

The utilization of lithium-ion batteries has been rapidly expanding across diverse sectors, including electric transportation, stationary energy storage systems, and the built environment. Ensuring a high level of reliability in these applications is essential, as the performance and safety of such systems depend strongly on the accurate assessment of the battery’s State of Health (SOH). Conventional SOH estimation techniques—often based on complex electrochemical models or extensive laboratory testing—tend to require a large number of measurements, advanced instrumentation, and high computational cost. These factors make them impractical for large-scale deployment or real-time monitoring. This study introduces a simplified machine-learning-based approach for …

Large-Scale Experimental Study On The Impact Of Air Cleaning & Ventilation On Indoor Air Quality And Student Illness-Related Absenteeism, Daud Nosham

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

This large-scale randomized experimental field study investigated the effect of portable air purifiers (PAPs) on classroom’s air quality and student’s illness related absenteeism. PAPs were installed in 317 classrooms from various school districts located in Eastern Nebraska. The classrooms were randomly assigned into four conditions: three treatment conditions (T1, T2 & T3) and one control condition (device without any filter). T1 was equipped with HEPA filters, T2 added Activated Carbon (AC) layer to HEPA, and T3 further integrated Germicidal Ultraviolet (GUV) alongside HEPA and AC filters. The measured variables were carbon dioxide (CO2), fine particles (PN2.5) and coarse particles (PNcoarse), …

Assessment Of Traffic Related Air Pollution Effects On Indoor Air Quality In Educational Buildings, Ahmed Gouda Mohamed, Mohamed Sherif Dr., Fahad Alqahtani Dr., Yousif Deeb Eng.

Civil Engineering

This study assesses the impact of traffic-related air pollution (TRAP) on indoor air quality (IAQ) within a Riyadh school. The main objectives are to pinpoint factors influencing IAQ and to evaluate the effectiveness of existing ventilation and filtration systems. Air quality Egg sensors monitored nitrogen dioxide (NO2), carbon monoxide (CO), and particulate matter (PM1.0, PM2.5, PM10) levels both indoors and outdoors over 30 days. Findings revealed average indoor PM2.5 and PM10 concentrations of 14.09 µg/m3 and 18.15 µg/m3, respectively, while outdoor concentrations averaged 20.63 µg/m3 and 27.88 µg/m3. A strong positive correlation was observed between indoor and outdoor PM levels, …

Mass Timber Construction: Products, Performance And Design, Anthony Harvey

Civil Engineering Professional Development Seminar

Due to their high strength, dimensional stability and positive environmental performance, mass timber building products are quickly becoming materials of choice for sustainably‐minded designers. This presentation will provide a detailed look at the variety of mass timber products available, including glue‐laminated timber (glulam), cross laminated timber (CLT), nail laminated timber (NLT), heavy timber decking, and other engineered and composite systems. Applications for the use of these products under modern building codes will be discussed, and examples of their use in U.S. projects reviewed. Mass timber’s ability to act as both structure and exposed finish will also be highlighted, as will …

Co2-Induced Changes In Rheology, Structural Evolution, And Particle Characteristics Of Cement Paste, Seongho Han, Tae Yong Shin, Seung Mo Kim, Jae Hong Kim, Kamal H. Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The injection of carbon dioxide (CO₂) into cementitious systems has emerged as a promising approach to enhancing sustainability in concrete production. This study explores the impact of CO₂ injection on the rheological behavior, structural build-up, and particle size evolution of cement paste by systematically varying the water-to-cement ratio (w/c) (0.35, 0.4, and 0.5) and CO₂ concentration (0.06, 0.28, and 0.84 mol). Rheological analysis revealed a significant increase in initial yield stress with CO₂ injection. Using the Modified Bingham model, yield stress increased by 72 % and 150 % for 0.28- and 0.84-mol CO₂, …

Common Ground Newsletter Fall 2025, Missouri University Of Science And Technology

Common Ground

- Internships

- Superb Seniors - Giving

- Standout Student Athletes

- Summer Camps

- Design Teams

- Alumni News

Terra Lunaris: Assessment Of A Lunar Habitat For Scientific Astronauts, Space Miners, Or Space Tourists, Dirk Schumann, Robert A. Goehlich

Publications

This conceptual paper explores ground- based habitable space modules for various applications. The Terra Lunaris concept serves as the baseline and is evaluated in comparison to existing and theoretical studies in this field. Terra Lunaris is a compact hybrid habitat that expands to offer nearly four times its transport volume by combining rigid modules with an inflatable shell. With most interior elements pre-installed and foldable, setup time and complexity are minimized. The design integrates technical zones, living quarters, and shared spaces, while also supporting psychological well-being under extreme conditions. The paper provides both qualitative and quantitative analyses of lunar habitation …

A Green Concrete Mixture Using Rice Husk As Partially Cement Replacement, Khloud Khalid Eldamshiry, Zeina Salama, Amany Micheal, Rania Rushdy Moussa, Ayatallah Raafat

Architectural Engineering

Egypt's agricultural waste production has increased significantly in recent decades, leading to improper disposal methods and environmental pollution. Rice husks are the most common agricultural solid waste in Egypt, contributing to "black clouds" and causing health issues. On the other hand, Cement, a crucial component of construction materials, generates unsound residues and greenhouse gas emissions. Green concrete with rice husks could be a profitable solution for environmentally sound construction, reducing cement consumption and increasing the durability and integrity of new materials. This study investigates the use untreated rice husk fibres with a concrete mixture, avoiding burning and contributing to environmental …

Demystifying The Discharge Coefficient For Flow Over Thin Weirs And Sills, Joseph E. Pugh, Subhas Karan Venayagamoorthy, Timothy K. Gates

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

A revised derivation of the discharge coefficient for flows over thin weirs and sills in the limits of wall overflow to a free overfall is given. Using dimensional analysis, we show that the discharge coefficient, (Formula presented), in the classical weir-discharge equation is best understood as a weir Froude number, (Formula presented), which accounts for the combined effects of inertia, contraction and viscous energy losses within the flow field. A comprehensive set of experimental data from historical studies is complimented by new data from the authors, featuring both laboratory flume experiments and three-dimensional numerical simulations of weir flows. Synthesis of …

Resilience Of Interdependent Transportation And Healthcare Systems: A Simulation-Driven Framework Incorporating Social Equity And Facility Optimization, S. Yasaman Ahmadi

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

The overarching goal of this dissertation is to develop an integrated, simulation-driven framework to assess and enhance the resilience of interdependent transportation and healthcare systems before, during, and after natural hazards. By examining how spatial disruptions, social vulnerability, operational constraints, and infrastructure interdependencies affect access to and functionality of hospitals, this research offers a multifaceted evaluation of system performance under stress. This dissertation examines the impact of natural hazards, particularly floods, on the interdependent transportation and healthcare systems. The proposed approach combines and advances GIS-based network analysis, graph-theoretical modeling, and discrete-event simulation to evaluate system performance under different scenarios. The …

Evaluating The Role Of Building Information Modeling (Bim) In Minimizing Delays And Reducing Costs In Construction Projects, Hussein Elsayed Mohamed Ismail, Mohammad Ahmad Mohammad Abdulhadi

Journal of Engineering Research

The implementation of Building Information Modeling (BIM) as a construction industry technology delivers extensive effects on project duration and financial management. This investigation examines BIM as a technology specifically designed to cut down construction project delays and decrease expenditures. The scholarly review of existing research material through a secondary approach allows this study to identify BIM's major value contributions.

The implementation of BIM technology enables project schedules to reach improved accuracy which results in a reduction of project delays by 15-25% because of its automation features and effective clash detection and real-time coordination benefits. The application of building information modeling …

The Xenaform, Cassadie J. Golding

Architectural Engineering

The XenaForm explores how complex, expressive structures can emerge from simple, low-tech construction methods using principles of parametric design and structural geometry. By combining folded plate techniques with modular tetrahedral components, the project bridges high-tech digital modeling and hands-on physical fabrication. The result is a lightweight, buildable system that reclaims the engineer’s role as a form-finder.

Architectural Engineering Institute: International Student Design Competition 2025, Alexandra Marie Kersting, Alec Thomas Gibbs, Haley Francesca Sousa, Kline Genevieve Nickel

Architectural Engineering

The AEI International Student Design Competition is an annual competition held by the Architectural Engineering Institute that aims to replicate an integrated building design process. The 2025 Cal Poly team consisted of 4 Architectural Engineering students, each competing in the Structural and Integration disciplines. The team was provided a set of architectural drawings and a 3D architectural Revit model of Carson Headquarters in Omaha, Nebraska. The team was tasked with the creation of a complete structural design as well as a discussion of integration of other building design disciplines.