Optics Commons^™

Hybrid Optical Integrator Based On Silicon-On-Insulator Platform, Taewon Huh

Graduate Theses - Physics and Optical Engineering

A hybrid optical integrator is a recirculating loop that performs oversampling typically for analog input, using the cross-gain modulation (XGM) in a semiconductor optical amplifier (SOA). The modulated input signal changes the gain of the loop through XGM and thus modifies the loop accumulation. This thesis presents hybrid optical integrator for an all-optical analog-to-digital converter based on a silicon photonics platform. The device consists of silicon waveguides of dimension 220 × 500 nm (thick × width) and approximately 5 m optical loop length including fiber length, input and output grating couplers for 1550 nm signal, directional couplers, and external components …

Distribution Of Tm 3+ And Ni 2+ In Chalcogenide Glass Ceramics Containing Ga2s3 Nanocrystals: Influence On Photoluminescence Properties, Xiaosong Lu, Zhiqiang Lai, Jing Ren, Lukas Strizik, Tomas Wagner, Yanqiu Du, Gerald Farrell, Pengfei Wang

Articles

The distribution of Tm3+ and Ni2+ ions is unambiguously exhibited in 80GeS2-20Ga2S3 chalcogenide glass ceramics (GCs) containing Ga2S3 nanocrystals (NCs) by using advanced analytical transmission electron microscopy. Distinctively different distribution patterns of Tm3+ and Ni2+ ions are observed in the GCs obtained by controlled crystallization. The distribution of the dopants imposes strong influence on their optical properties which are revealed by absorption and photoluminescence (PL) spectra. Detailed discussions are given of the mechanisms of the crystallization-induced PL enhancement and quenching of the Tm3+ mid-infrared and Ni2+ near-infrared emissions, respectively.

All Fibre Q-Switched Thulium-Doped Fibre Laser Incorporating Thulium–Holmium Co-Doped Fibre As A Saturable Absorber, Shi Li, Elfed Lewis, Gerald Farrell, Ahmad Haziq Aiman Rosol, A.A. Latiff, Sulaiman Wadi Harun, Bingang Guo, Pengfei Wang

Articles

A novel all fibre Q-switched Thulium-doped fibre laser (TDFL) is reported which includes a short length of a Thulium–Holmiumco-doped fibre (THDF) as a saturable absorber. A high repetition rate (27.26 kHz) coupled with a low pulse width (19.06μs) is obtained for single wavelength Q-switched pulse operation at an output wavelength of 1911.5 nm using a pump power of 200 mW. Increasing the pump power from 200 mW to 700 mW results in the repetition rate increasing from 27.26 kHz to 99.67 kHz and the pulse width decreasing from 19.06μs to 920 ns. The centre wavelength of the single Q-switched pulse …

In-Fiber Temperature Sensor Based On Green Up-Conversion Luminescence In An Er3+-Yb3+ Co-Doped Tellurite Glass Microsphere, Meng Zhang, Angzhen Li, Jibo Yu, Xiaosong Lu, Shunbin Wang, Elfed Lewis, Gerald Farrell, Libo Yuan, Pengfei Wang

Articles

A novel, to the best of our knowledge, in-fiber temperature sensor based on green up-conversion (UC) luminescence in an Er3+-Yb3+" role="presentation" style="box-sizing: border-box; display: inline; font-size: 12.88px; line-height: normal; word-spacing: normal; overflow-wrap: normal; white-space: nowrap; float: none; direction: ltr; max-width: none; max-height: none; min-width: 0px; min-height: 0px; border: 0px; padding: 0px; margin: 0px; position: relative;">Er3+-Yb3+Er3+-Yb3+ co-doped tellurite glass microsphere is described. The tellurite glass microsphere is located firmly inside a suspended tri-core hollow-fiber (STCHF) structure. The pump light launched via a single-mode fiber (SMF) is passed through a section of multimode fiber, which is fusion spliced between the SMF …

Theoretical Analysis Of A Volume Holographic Lens Using Matlab, Sanjay Keshri, Kevin Murphy, Izabela Naydenova, Suzanne Martin

Conference Papers

Volume holographic lenses have great potential for different types of applications requiring light redirection and beam shaping such as solar light collection and LED light management. For lighting applications using LEDs, it is essential to make a highly efficient optical element to be placed in front of the LED in order to decrease energy losses. For that reason, a careful theoretical analysis of the properties and operation regime of the lens must be carried out at the design stage. The characteristics of focusing Holographic Optical Elements (HOE) depend on many factors including their thickness, spatial frequency, the angular range of …

Sensing Of Multiple Parameters With Whispering Gallery Mode Optical Fiber Micro-Resonators, Arun Kumar Mallik Dr, Vishnan Kavungal, Gerald Farrell, Yuliya Semenova

Conference Papers

Monitoring of multiple physical parameters, such as humidity, temperature, strain, concentrations of certain chemicals or gases in various environments is of great importance in many industrial applications both for minimizing adverse effects on human health as well as for maintaining production levels and quality of products. In this paper we demonstrate two different approaches to the design of multi-parametric sensors using coupled whispering gallery mode (WGM) optical fiber micro-resonators. In the first approach, a small array of micro-resonators is coupled to a single fiber taper, while in the second approach each of the micro-resonators within an array is coupled to …

Sns Optical Fiber Structure Sensor For Direct Detection Of The Phase Transition In C18h38 N-Alkane Material, Wei Han, Marek Rebow, Xiaokang Lian, Dejun Liu, Gerald Farrell, Qiang Wu, Yuliya Semenova

Articles

A singlemode-no-core-singlemode (SNS) fiber structure optical sensor for detecting the solid-liquid phase change in a phase change material: C18H38 n-alkane material (n-octadecane) is proposed and demonstrated. The transmission-type sensor probe consists of a short section of no-core fiber sandwiched between two sections of a singlemode fiber. Phase changes in n-octadecane are accompanied by large step-like variations of its refractive index (RI). Such a large discontinuous change of the n-octadecane’s RI during its phase transition, leads to the corresponding step-like change in the transmitted optical power that can reliably indicate the phase change of the sample in the vicinity of the …

Ultrabroadband Mid-Infrared Emission From Cr 2+ -Doped Infrared Transparent Chalcogenide Glass Ceramics Embedded With Thermally Grown Zns Nanorods, Xiaosong Lu, Zhiqiang Lai, Runan Zhang, Haitao Guo, Jing Ren, Lukas Strizik, Tomas Wagner, Gerald Farrell, Pengfei Wang

Articles

We report, for the first time to our knowledge, an ultrabroadband mid-infrared (MIR) emission in the range of 1800–2800 nm at room temperature from a Cr2+-doped chalcogenide glass ceramic embedded with pure hexagonal (wurtzite) β-ZnS nanorods and study the emission-dependent properties on the doping concentration of Cr2+. A new family of chalcogenide glasses based on (100 − x) Ge1.5As2S6.5 – x ZnSe (in mol.%) was prepared by melt-quenching method. The Cr2+: β-ZnS nanorods of ˜150 nm in diameter and ˜1 μm in length were grown in the Cr2+-doped glass after thermal annealing. The compositional variations of glass structures and optical …

Fundamental Properties Of Metallic Nanolasers, William Hayenga

Electronic Theses and Dissertations

The last two decades have witnessed tremendous advancements in the area of nanophotonics and plasmonics, which has helped propel the development of integrated photonic sources. Of central importance to such circuits is compact, scalable, low threshold, and efficient coherent sources that can be driven at high modulation frequencies. In this regard, metallic nanolasers offer a unique platform. Their introduction has enabled confinement of light at a subwavelength scale and the ultra-small size of the modes afforded by these structures allows for cavity enhancing effects that can help facilitate thresholdless lasing and large direct modulation bandwidths. In this report, I present …

Processing Of Advanced Infrared Materials, Daniel Mcgill

Electronic Theses and Dissertations

Infrared transparent glassy and crystalline materials often have unique and complex processing requirements but are an important class of materials for such applications as optical windows, lenses, waveplates, polarizers and beam splitters. This thesis investigates two specific materials, one amorphous and one crystalline, that are candidates for use in the short and midwave-infrared and mid and longwave infrared, respectively. It is demonstrated that an innovative uniaxial sintering process, which uses a sacrificial pressure-transmitting medium, can be used to fully densify a 70TeO2-20WO3-10La2O3 (TWL) glass powder. The characteristics of the sintered TWL glass is compared to that of a parent glass …

Dynamics Of Swept Source Lasers, Ben O'Shaughnessy

Theses

The aim of this thesis is to investigate the dynamics of two kinds of swept source lasers for optical coherence tomography. A mathematical model consisting of a pair of coupled delay differential equations was adapted to study Fourier Domain Mode-Locked (FDML) lasers and short cavity swept source lasers, and to explain experimental observations of these lasers.

The short cavity laser is experimentally observed to produce pulses during the frequency sweep. This ‘sliding frequency mode-locking’ behaviour is reproduced by simulation, which is then used to establish simple relationships between the key parameters of sweep speed, linewidth and output power.

The FDML …

Development Of Uv Led Based Lamps With Modular Optical Heads, Ciara O'Hara

Theses

This project was centred around the development of the optical components, and the optimisation of the optical performance, of ProPhotonix Ltd’s Cobra Cure FX series of products. These are high irradiance, high dose, UVA (primarily 395 nm and 365 nm) Light Emitting Diode (LED) lamps designed for curing applications. An initial prototype developed by ProPhotonix, the smallest in the series, the FX1, underwent significant redesign throughout the project, and the two larger lamps, the FX2 and the FX3 were developed during the course of the project. This work primarily consisted in characterising, accurately modelling, and thereby refining, the optical reflector …

Active Recall Networks For Multiperspectivity Learning Through Shared Latent Space Optimization, Theus Aspiras, Ruixu Liu, Vijayan K. Asari

Electrical and Computer Engineering Faculty Publications

Given that there are numerous amounts of unlabeled data available for usage in training neural networks, it is desirable to implement a neural network architecture and training paradigm to maximize the ability of the latent space representation. Through multiple perspectives of the latent space using adversarial learning and autoencoding, data requirements can be reduced, which improves learning ability across domains. The entire goal of the proposed work is not to train exhaustively, but to train with multiperspectivity. We propose a new neural network architecture called Active Recall Network (ARN) for learning with less labels by optimizing the latent space. This …

Deep Temporal Convolutional Networks For Short-Term Traffic Flow Forecasting, Wentian Zhao, Yanyun Gao, Tingxiang Ji, Xili Wan, Feng Ye, Guangwei Bai

Electrical and Computer Engineering Faculty Publications

To reduce the increasingly congestion in cities, it is essential for intelligent transportation system (ITS) to accurately forecast the short-term traffic flow to identify the potential congestion sites. In recent years, the emerging deep learning method has been introduced to design traffic flow predictors, such as recurrent neural network (RNN) and long short-term memory (LSTM), which has demonstrated its promising results. In this paper, different from existing work, we study the temporal convolutional network (TCN) and propose a deep learning framework based on TCN model for short-term city-wide traffic forecast to accurately capture the temporal and spatial evolution of traffic …

Non Linear Optics For Materials Fabrication And Medical Instrumentation, Aurelio Paez

Open Access Theses & Dissertations

Two-photon absorption is a nonlinear optical process where two photons are absorbed by a molecule simultaneously. The probability of this quantum phenomenon is proportional to the quadratic excitation of light intensity. It has many applications in biomedical and materials research, such as two-photon fluorescence microcopy. The first project is to apply two-photon absorption induced bond cleavage in photoreactive materials for engineering 3D tissue scaffolds. The major challenge for growing thick 3D tissues is the lack of vasculature, where nutrients and oxygen can be delivered to the growing cells. Our collaborators have synthesized a novel polypeptide that is composed of 34-mer …

A Twelve-Wavelength Thulium-Doped Fibre Laser Based On A Microfibre Coil Resonator Incorporating Black Phosphorus, Shi Li, Yu Yin, Elfed Lewis, Gerald Farrell, Pengfei Wang

Articles

A novel multi-wavelength continuous Thulium-doped fibre laser incorporating a microfibre coil resonator based on black phosphorus (MCR-BP) material has been successfully fabricated and demonstrated. A twelve-wavelength spectrum with 0.54 nm channel spacing has been achieved by simply adjusting the pump source power. A single peak extinction ratio of more than 40 dB was observed. The superior performance of the MCR-BP described in this article compared to conventional MCR based fibre lasers can be attributed the inclusion of the Black Phosphorous Material. The enhanced lasing is primarily due to the twin properties of the MCR-BP device combining a comb-like filter effect …

Mode Transition In Conventional Step-Index Optical Fibers, Xiaokang Lian, Gerald Farrell, Qiang Wu, Wei Han, Fangfang Wei, Yuliya Semenova

Conference Papers

The discrete self-imaging effect reveals the distinct properties of cladding modes with core modes in step-index optical fibers, as was shown in our previous work [1], where only the linearly polarized LP0n modes were studied. In this paper, the dispersion diagram of the first 17 vector modes (TE0n, TM0n, HEmn and EHmn) and the related first 9 LPmn modes are calculated by both the full-vector finite element method and the graphical method with a three-layer step-index optical fiber model. The cladding modes distributions and the transitions between the core and cladding modes are analyzed. The results of this work are …

Third-Order Optical Nonlinearity Properties Of Cdcl2-Modifed Ge–Sb–S Chalcogenide Glasses, Xiaosong Lu, Jianhui Li, Lu Yang, Runan Zhang, Yindong Zhang, Jing Ren, Aurelian Catalin Galca, Mihail Secu, Gerald Farrell, Pengfei Wang

Articles

We developed a new type of chalcohalide glasses with physicochemical and nonlinear optical properties that are tunable by composition. It is found that more than 60 mol.% CdCl2 heavy metal halide can be dissolved into the ternary Ge–Sb–S system and forming stable glasses. The visible-light transparency range is extended to shorter wavelengths with the addition of CdCl2, which is beneficial for the optical quality control and infra-red (IR) system alignment. The third-order optical nonlinearity (TONL) is studied using the femtosecond Z-scan method. The results show that both the nonlinear refractive index and two photon absorption co-efficient decrease with CdCl2. Benefiting …

High Performance Liquid Crystal Devices For Augmented Reality And Virtual Reality, Md Javed Rouf Talukder

Electronic Theses and Dissertations

See-through augmented reality and virtual reality displays are emerging due to their widespread applications in education, engineering design, medical, retail, transportation, automotive, aerospace, gaming, and entertainment. For augmented reality and virtual reality displays, high-resolution density, high luminance, fast response time and high ambient contrast ratio are critically needed. High-resolution density helps eliminate the screen-door effect, high luminance and fast response time enable low duty ratio operation, which plays a key role for suppressing image blurs. A dimmer placed in front of AR display helps to control the incident background light, which in turn improves the image contrast. In this dissertation, …

Imaging Through Glass-Air Anderson Localizing Optical Fiber, Jian Zhao

Electronic Theses and Dissertations

The fiber-optic imaging system enables imaging deeply into hollow tissue tracts or organs of biological objects in a minimally invasive way, which are inaccessible to conventional microscopy. It is the key technology to visualize biological objects in biomedical research and clinical applications. The fiber-optic imaging system should be able to deliver a high-quality image to resolve the details of cell morphology in vivo and in real time with a miniaturized imaging unit. It also has to be insensitive to environmental perturbations, such as mechanical bending or temperature variations. Besides, both coherent and incoherent light sources should be compatible with the …

Novel Solid State Lasers Based On Volume Bragg Gratings, Evan Hale

Electronic Theses and Dissertations

Since their invention in 1960, lasers have revolutionized modern technology, and tremendous amounts of innovation and development has gone into advancing their properties and efficiencies. This dissertation reports on further innovations by presenting novel solid state laser systems based on the volume Bragg gratings (VBGs) and the newly developed holographic phase mask (HPMs) for brightness enhancement, dual wavelength operation, and mode conversion. First, a new optical element was created by pairing the HPM with two surface gratings creating an achromatic holographic phase mask. This new optical device successfully performed transverse mode conversion of multiple narrow line laser sources operating from …

High-Dynamic-Range Foveated Near-Eye Display System, Guanjun Tan

Electronic Theses and Dissertations

Wearable near-eye display has found widespread applications in education, gaming, entertainment, engineering, military training, and healthcare, just to name a few. However, the visual experience provided by current near-eye displays still falls short to what we can perceive in the real world. Three major challenges remain to be overcome: 1) limited dynamic range in display brightness and contrast, 2) inadequate angular resolution, and 3) vergence-accommodation conflict (VAC) issue. This dissertation is devoted to addressing these three critical issues from both display panel development and optical system design viewpoints. A high-dynamic-range (HDR) display requires both high peak brightness and excellent dark …

Recurrent Residual U-Net For Medical Image Segmentation, Md Zahangir Alom, Christopher Yakopcic, Mahmudul Hasan, Tarek M. Taha, Vijayan K. Asari

Electrical and Computer Engineering Faculty Publications

Deep learning (DL)-based semantic segmentation methods have been providing state-of-the-art performance in the past few years. More specifically, these techniques have been successfully applied in medical image classification, segmentation, and detection tasks. One DL technique, U-Net, has become one of the most popular for these applications. We propose a recurrent U-Net model and a recurrent residual U-Net model, which are named RU-Net and R2U-Net, respectively. The proposed models utilize the power of U-Net, residual networks, and recurrent convolutional neural networks. There are several advantages to using these proposed architectures for segmentation tasks. First, a residual unit helps when training deep …

A Survey Of Techniques For Mobile Service Encrypted Traffic Classification Using Deep Learning, Pan Wang, Xuejiao Chen, Feng Ye, Zhixin Sun

Electrical and Computer Engineering Faculty Publications

The rapid adoption of mobile devices has dramatically changed the access to various net- working services and led to the explosion of mobile service traffic. Mobile service traffic classification has been a crucial task that attracts strong interest in mobile network management and security as well as machine learning communities for past decades. However, with more and more adoptions of encryption over mobile services, it brings a lot of challenges about mobile traffic classification. Although classical machine learning approaches can solve many issues that port and payload-based methods cannot solve, it still has some limitations, such as time-consuming, costly handcrafted …

Mode Coupling In Space-Division Multiplexed Systems, Huiyuan Liu

Electronic Theses and Dissertations

Even though fiber-optic communication systems have been engineered to nearly approach the Shannon capacity limit, they still cannot meet the exponentially-growing bandwidth demand of the Internet. Space-division multiplexing (SDM) has attracted considerable attention in recent years due to its potential to address this capacity crunch. In SDM, the transmission channels support more than one spatial mode, each of which can provide the same capacity as a single-mode fiber. To make SDM practical, crosstalk among modes must be effectively managed. This dissertation presents three techniques for crosstalk management for SDM. In some cases such as intra-datacenter interconnects, even though mode crosstalk …

Pursuing Natural Unity, Consciousness Included, Rowen Cox-Rubien

Scripps Senior Theses

An ontological exploration of consciousness and how it is related to the body and other aspects of physical reality. Framed by David Chalmers' conception of "The Hard Problem", we begin from a physicalist perspective to discuss the problem of mental causation, which is the inquiry of how the mind communicates and interacts with the body. From here we examine the employment of identity reduction to functionalize and therefore physically explain mentality. We find that reductionist methods, the backbone of scientific investigation, do not work to explain conscious experience, because conscious experience is not quantifiable--it is qualitative. Thus we are left …

Study Of Blinking Statistics In Silver Coated Cobalt Ferrite Single Nanoprticle Using Two-Photon Fluorescence Microscopy, Rajen Kumar Goutam

Open Access Theses & Dissertations

Two-photon fluorescence microscopy is a powerful tool to study the molecular and cellular interactions. This technology is a non-invasive approach with the advantage of three-dimensional imaging up to submicron resolution. Two-photon excitation process is the result of simultaneous absorption of two photons that has special features of reduced photodamaged and elongated penetration depth on samples. In this work, blinking statistics of silver-coated Cobalt ferrite (CoFe2O4) single nanocrystal is studied using two-photon fluorescence microscopy. By defining the intensity threshold, the observed fluorescence is divided into two distinct stages: OFF and ON states. Both of these states followed the inverse power law. …

Using Two-Photon Microscopy To Analyze Arabidopsis Thaliana Leaves Under Autophagy Conditions And Second Harmonic Generation In Collagen, Andres Martin Reyes

Open Access Theses & Dissertations

Two-photon microscopy has emerged as a highly efficient and effective imaging tool for biological samples. This can be utilized in studying recently emerging technologies and conditions such as the autophagy process in arabidopsis thaliana leaves and second harmonic generation in collagen. Both of these areas of study utilize the two-photon microscopy practice effectively in uncovering more information of the biological nature of examined samples.

Spectroscopy Of Neon For The Advanced Undergraduate Laboratory, H. C. Busch, M. B. Cooper, C. I. Sukenik

Physics Faculty Publications

We describe a spectroscopy experiment, suitable for upper-division laboratory courses, that investigates saturated absorption spectroscopy and polarization spectroscopy in a neon discharge. Both experiments use nearly identical components, allowing students to explore both techniques in a single apparatus. Furthermore, because the wavelength of the laser is in the visible part of the spectrum (640 nm), the experiment is well-suited for students with limited experience in optical alignment. The labs nicely complement a course in atomic or plasma physics, provide students with the opportunity to gain important technical skills in the area of optics and lasers, and can provide an introduction …

Broadband Mid-Infrared Frequency Combs Generated Via Frequency Division, Qitian Ru

Electronic Theses and Dissertations

Frequency combs have revolutionized metrology and demonstrated numerous applications in science and technology. Combs operating in the mid-infrared region could be beneficial for molecular spectroscopy for several reasons. First, numerous molecules have their spectroscopic signatures in this region. Furthermore, the atmospheric window (3-5μm and 8-14μm) is located here. Additionally, a mid-infrared frequency comb could be employed as a diagnostic tool for the many components of human breath, as well as for detection of harmful gases and contaminants in the atmosphere. In this thesis, I used synchronously pumped subharmonic optical parametric oscillators (OPOs) operating at degeneracy to produce ultra-broadband outputs near …