Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Publication Year
- Publication Type
Articles 1 - 20 of 20
Full-Text Articles in Optics
Proposed Methodology For Correcting Fourier-Transform Infrared Spectroscopy Field-Of-View Scene-Change Artifacts, Kody A. Wilson, Michael L. Dexter, Benjamin F. Akers, Anthony L. Franz
Proposed Methodology For Correcting Fourier-Transform Infrared Spectroscopy Field-Of-View Scene-Change Artifacts, Kody A. Wilson, Michael L. Dexter, Benjamin F. Akers, Anthony L. Franz
Faculty Publications
Fourier-transform spectrometers are widely used for spectral measurements. Changes in the field of view during measurement introduce oscillations into the measured spectra known as scene-change artifacts. Field-of-view changes also introduce uncertainty about which target the measured spectrum represents. Though scene-change artifacts are often present in dynamic data, their significance is disputed in the current literature. This work presents a theoretical framework and experimental validation for scene-change artifacts. Field-of-view changes introduce variable interferogram offsets, which standard processing techniques assume are constant. The error between the interferogram offset and its estimate is Fourier-transformed, yielding scene-change artifacts, often confused with noise, in the …
Method For Target Detection In A High Noise Environment Through Frequency Analysis Using An Event-Based Vision Sensor, Will Johnston, Shannon Young, David Howe, Rachel Oliver, Zachary Theis, Brian Mcreynolds, Michael L. Dexter
Method For Target Detection In A High Noise Environment Through Frequency Analysis Using An Event-Based Vision Sensor, Will Johnston, Shannon Young, David Howe, Rachel Oliver, Zachary Theis, Brian Mcreynolds, Michael L. Dexter
Faculty Publications
Event-based vision sensors (EVSs), often referred to as neuromorphic cameras, operate by responding to changes in brightness on a pixel-by-pixel basis. In contrast, traditional framing cameras employ some fixed sampling interval where integrated intensity is read off the entire focal plane at once. Similar to traditional cameras, EVSs can suffer loss of sensitivity through scenes with high intensity and dynamic clutter, reducing the ability to see points of interest through traditional event processing means. This paper describes a method to reduce the negative impacts of these types of EVS clutter and enable more robust target detection through the use of …
Event-Based Imaging Polarimeter, Michael R. Hawks, Michael L. Dexter
Event-Based Imaging Polarimeter, Michael R. Hawks, Michael L. Dexter
Faculty Publications
The design and initial experimental results from an event-based, rotating-polarizer, imaging polarimeter are presented. The speed of division-of-time imaging systems is traditionally constrained by the frame rate of the focal plane sensor and the need to sample several polarization angles during rotation. The asynchronous event reporting of event-based cameras (EBCs) frees these constraints but introduces challenges. The Stokes vectors used to describe polarization are based on irradiance, but EBCs are inherently change-detection systems that struggle to estimate irradiance. Two methods of estimating the polarization state without first recovering irradiance images are presented and compared. The DAVIS 346 sensor enables simultaneous …
Digital Holography Efficiency Experiments For Tactical Applications, Douglas E. Thornton
Digital Holography Efficiency Experiments For Tactical Applications, Douglas E. Thornton
Theses and Dissertations
Digital holography (DH) uses coherent detection and offers direct access to the complex-optical field to sense and correct image aberrations in low signal-to-noise environments, which is critical for tactical applications. The performance of DH is compared to a similar, well studied deep-turbulence wavefront sensor, the self-referencing interferometer (SRI), with known efficiency losses. Wave optics simulations with deep-turbulence conditions and noise were conducted and the results show that DH outperforms the SRI by 10's of dB due to DH's strong reference. Additionally, efficiency experiments were conducted to investigate DH system losses. The experimental results show that the mixing efficiency (37%) is …
Reconstruction Of The 3d Temperature And Species Concentration Spatial Distribution Of A Jet Engine Exhaust Plume Using An Infrared Fourier Transform Spectrometer Hyperspectral Imager, Mason D. Paulec
Theses and Dissertations
The measurement of combustion byproducts is useful for determining pollution of any fuel burning application, efficiency of combustion, and determining detectability of aircraft exhausts. Both intrusive and non-intrusive techniques have been utilized to measure these quantities. For the majority of the non-intrusive techniques, the absorption and emission spectra of the gases are utilized for measurements. For this research, the use of the Telops Infrared Fourier Transform Spectrometer (IFTS) Hyperspectral Imager (HSI) was explored within the scope of combustion diagnostic methods, as an option for remote measurements of a jet turbine to determine concentration of species and temperature of the combustion …
Evaluation And Quantification Of Diffractive Plenoptic Camera Algorithm Performance, Jack A. Shepherd Iii
Evaluation And Quantification Of Diffractive Plenoptic Camera Algorithm Performance, Jack A. Shepherd Iii
Theses and Dissertations
A diffractive plenoptic camera is a novel approach to the traditional plenoptic camera which replaces the main optic with a Fresnel zone plate making the camera sensitive to wavelength instead of range. However, algorithms are necessary to reconstruct the image produced by plenoptic cameras. While many algorithms exist for traditional plenoptic cameras, their ability to create spectral images in a diffractive plenoptic camera is unknown. This paper evaluates digital refocusing, super resolution, and 3D deconvolution through a Richardson-Lucy algorithm as well as a new Gaussian smoothing algorithm. All of the algorithms worked well near the Fresnel zone plate design wavelength, …
Investigation Of Scramjet Flowfield Temperatures At The Boundary Layer With Hyperspectral Imaging, Amy M. Kerst
Investigation Of Scramjet Flowfield Temperatures At The Boundary Layer With Hyperspectral Imaging, Amy M. Kerst
Theses and Dissertations
Within the domain of chemical propulsion, the fields of combustion diagnostics and computational fluid dynamics each have a long history, and both have led to a better understanding of complex phenomena yielding practical improvements in propulsion systems. As more exotic forms of propulsion are developed, the importance of both diagnostic and simulation capabilities also increase. In the case of scramjet combustion, these challenges primarily arise from the highly turbulent environment in the combustion cavity, and the high-speed, compressible nature of the flowfield. Efforts are underway to develop computer models of scramjet combustion environments to better understand the evolution of the …
Estimating Index Of Refraction For Specular Reflectors Using Passive Polarimetric Hyperspectral Radiance Measurements, Jacob A. Martin, Kevin C. Gross
Estimating Index Of Refraction For Specular Reflectors Using Passive Polarimetric Hyperspectral Radiance Measurements, Jacob A. Martin, Kevin C. Gross
Faculty Publications
Results of a method of estimating index of refraction from passive, polarimetric hyperspectral imaging radiance measurements are presented. As off-nadir viewing hyperspectral imaging platforms gain prominence, estimating index of refraction, which is invariant to viewing angle, may prove advantageous to estimating the emissivity, which is not. Results show that index of refraction can be retrieved to within 8% rms error for fused silica and sapphire glass targets, while simultaneously estimating object temperature. The accuracy and self-consistency of this technique for estimating index of refraction are shown to compare favorably to the maximum smoothness temperature–emissivity separation algorithm. Additionally, the results show …
The Fresnel Zone Light Field Spectral Imager, Francis D. Hallada
The Fresnel Zone Light Field Spectral Imager, Francis D. Hallada
Theses and Dissertations
This thesis provides a computational model and the first experimental demonstration of a Fresnel zone light field spectral imaging (FZLFSI) system. This type of system couples an axial dispersion binary diffractive optic with light field (plenoptic) camera designs providing a snapshot spectral imaging capability. A computational model of the system was developed based on wave optics methods using Fresnel propagation. It was validated experimentally and provides excellent demonstration of system capabilities. The experimentally demonstrated system was able to synthetically refocus monochromatic images across greater than a 100nm bandwidth. Furthermore, the demonstrated system was modeled to have a full range of …
Passively Estimating Index Of Refraction For Specular Reflectors Using Polarimetric Hyperspectral Imaging, Jacob A. Martin
Passively Estimating Index Of Refraction For Specular Reflectors Using Polarimetric Hyperspectral Imaging, Jacob A. Martin
Theses and Dissertations
As off-nadir viewing platforms becoming increasingly prevalent in remote sensing, material classification and ID techniques robust to changing viewing geometries must be developed. Traditionally, either reflectivity or emissivity are used for classification, but these quantities vary with viewing angle. Instead, estimating index of refraction may be advantageous as it is invariant with respect to viewing geometry. This work focuses on estimating index of refraction from LWIR (875-1250 wavenumbers) polarimetric hyperspectral radiance measurements.
Laminar Flame Combustion Diagnostics Using Imaging Fourier Transform Spectroscopy, Michael R. Rhoby
Laminar Flame Combustion Diagnostics Using Imaging Fourier Transform Spectroscopy, Michael R. Rhoby
Theses and Dissertations
Laminar flames are an important tool in combustion diagnostics with a host of pre-existing experimental research methods. Currently, however, no method captures time-resolved scalar profile estimates of temperature, and major species concentrations with a single measurement. This work provides IFTS with the capability to measure time-resolved 3D imaging of scalar values in laminar axisymmetric flames. This will make IFTS a useful tool for understanding combustion phenomenon, validating chemical kinetic models, verifying numerical simulations, and system performance estimate. Two algorithms are presented. The first reconstructs spectra as a function of flame period. Through selectively averaging over an ensemble of measurements, interferograms …
Image-Based Bidirectional Reflectance Distribution Function Of Human Skin In The Visible And Near Infrared, Jeffrey R. Bintz
Image-Based Bidirectional Reflectance Distribution Function Of Human Skin In The Visible And Near Infrared, Jeffrey R. Bintz
Theses and Dissertations
Human detection is an important first step in locating and tracking people in many missions including SAR and ISR operations. Recent detection systems utilize hyperspectral and multispectral technology to increase the acquired spectral content in imagery and subsequently better identify targets. This research demonstrates human detection through a multispectral skin detection system to exploit the unique optical properties of human skin. At wavelengths in the VIS and NIR regions of the electromagnetic spectrum, an individual can be identified by their unique skin parameters. Current detection methods base the skin pixel selection criteria on a diffuse skin reflectance model; however, it …
Experimental And Theoretical Basis For A Closed-Form Spectral Brdf Model, Samuel D. Butler
Experimental And Theoretical Basis For A Closed-Form Spectral Brdf Model, Samuel D. Butler
Theses and Dissertations
The microfacet class of BRDF models is frequently used to calculate optical scatter from realistic surfaces using geometric optics, but has the disadvantage of not being able to consider wavelength dependence. This dissertation works toward development of a closed-form approximation to the BRDF that is suitable for hyperspectral remote sensing by presenting measured BRDF data of 12 different materials at four different incident angles and up to seven different wavelengths between 3.39 and 10.6 micrometer. The data was intended to be fit to various microfacet BRDF models to determine an appropriate form of the wavelength scaling. However, when fitting the …
Range Finding With A Plenoptic Camera, Robert A. Raynor
Range Finding With A Plenoptic Camera, Robert A. Raynor
Theses and Dissertations
The plenoptic camera enables simultaneous collection of imagery and depth information by sampling the 4D light field. The light field is distinguished from data sets collected by stereoscopic systems because it contains images obtained by an N by N grid of apertures, rather than just the two apertures of the stereoscopic system. By adjusting parameters of the camera construction, it is possible to alter the number of these `subaperture images,' often at the cost of spatial resolution within each. This research examines a variety of methods of estimating depth by determining correspondences between subaperture images. A major finding is that …
Comparative Analysis Of Reconstructed Image Quality In A Simulated Chromotomographic Imager, Ryan L. Tervo
Comparative Analysis Of Reconstructed Image Quality In A Simulated Chromotomographic Imager, Ryan L. Tervo
Theses and Dissertations
A hyperspectral chromotomographic instrument has been developed to determine the spatial and spectral distribution of a target. It does this by recording the dispersed images produced by a rotating direct vision prism with a high speed camera. The recorded images are processed through a tomographic reconstruction algorithm to produce a reconstructed hypercube. A physics-based system model was developed to investigate three areas. The first was how the prism angle selection and range of angles used impacted the reconstructed image quality. The second was an assessment of a new iterative reconstruction algorithm developed to remove artifacts produced in the Back Projection …
Development And Characterization Of A Chromotomosynthetic Hyperspectral Imaging System, Randall L. Bostick
Development And Characterization Of A Chromotomosynthetic Hyperspectral Imaging System, Randall L. Bostick
Theses and Dissertations
A chromotomosynthetic imaging (CTI) methodology based upon mathematical reconstruction of a set of 2-D spectral projections to collect high-speed (100 Hz) 3-D hyperspectral data cube has been proposed. The CTI system can simultaneously provide usable 3-D spatial and spectral information, provide high-frame rate slitless 1-D spectra, and generate 2-D imagery equivalent to that collected with no prism in the optical system. The wavelength region where prism dispersion is highest (500 nm) is most sensitive to loss of spectral resolution in the presence of systematic error, while wavelengths 600 nm suffer mostly from a shift of the spectral peaks. The quality …
Development Of A Spectropolarimetric Capability, Evan J. Carlson
Development Of A Spectropolarimetric Capability, Evan J. Carlson
Theses and Dissertations
A Bomem 200 series Fourier transform infrared spectrometer and FLIR Systems Inc InGaAs infrared (IR) camera was used to measure the degree of linear polarization (DOLP) from a metal and glass surfaces. This was accomplished by placing a wire grid polarizer in front of the aperture of the FTIR and IR camera to measure the polarized reflection from the target material. For the IR camera, an average of pixel counts was collected over the area of the target to measure to DOLP. Factors impacting the accuracy of the measurements from the FTIR are calibration, instrument self emission, and alignment error. …
Discrimination Of Neutral Postures In Computer Based Work, Alanna R. Keith
Discrimination Of Neutral Postures In Computer Based Work, Alanna R. Keith
Theses and Dissertations
A biometric system recognizes users based on the way they physically interact with the system. In this work, we discover a common behavior that a typist consistently displays in non-trivial computer work. We sought to demonstrate three objectives: first, compelling proof that a user can be actively recognized over the course of a lengthy task via a neutral posture struck multiple times in that task; two, a sensing concept for capturing the neutral posture, and, third, an objective method for determine the level of work performed by each typist. This thesis develops a model for hand tracking using a simple …
3-D Scene Reconstruction From Aerial Imagery, Jared M. Ekholm
3-D Scene Reconstruction From Aerial Imagery, Jared M. Ekholm
Theses and Dissertations
3-D scene reconstructions derived from Structure from Motion (SfM) and Multi-View Stereo (MVS) techniques were analyzed to determine the optimal reconnaissance flight characteristics suitable for target reconstruction. In support of this goal, a preliminary study of a simple 3-D geometric object facilitated the analysis of convergence angles and number of camera frames within a controlled environment. Reconstruction accuracy measurements revealed at least 3 camera frames and a 6 convergence angle were required to achieve results reminiscent of the original structure. The central investigative effort sought the applicability of certain airborne reconnaissance flight profiles to reconstructing ground targets. The data sets …
Shock Wave Dynamics Of Novel Aluminized Detonations And Empirical Model For Temperature Evolution From Post-Detonation Combustion Fireballs, Joe Motos Gordon
Shock Wave Dynamics Of Novel Aluminized Detonations And Empirical Model For Temperature Evolution From Post-Detonation Combustion Fireballs, Joe Motos Gordon
Theses and Dissertations
This research characterizes the blast wave and temperature evolution of an explosion fireball in order to improve the classification of aluminized conventional munitions based on a single explosive type such as RDX. A drag model fit to data shows initial shock velocities of 1.6-2.8 km/s and maximum fireball radii ranging from 4.3-5.8 m with most of the radii reached by 50 ms upon detonation. The Sedov-Taylor point blast model is fitted to data where a constant release (s=1) of energy upon detonation suggests shock energies of 0.5-8.9 MJ with blast dimensionalities indicative of the spherical geometry (n3) observed in visible …