Applied Mechanics Commons^™

Effects Of Magnetic Field On The Shape Memory Behavior Of Single And Polycrystalline Magnetic Shape Memory Alloys, Ali S. Turabi

Theses and Dissertations--Mechanical and Aerospace Engineering

Magnetic Shape Memory Alloys (MSMAs) have the unique ability to change their shape within a magnetic field, or in the presence of stress and a change in temperature. MSMAs have been widely investigated in the past decade due to their ability to demonstrate large magnetic field induced strain and higher frequency response than conventional shape memory alloys (SMAs). NiMn-based alloys are the workhorse of metamagnetic shape memory alloys since they are able to exhibit magnetic field induced phase transformation. In these alloys, martensite and austenite phases have different magnetization behavior, such as the parent phase can be ferromagnetic and martensite …

High Temperature Flow Solver For Aerothermodynamics Problems, Huaibao Zhang

Theses and Dissertations--Mechanical and Aerospace Engineering

A weakly ionized hypersonic flow solver for the simulation of reentry flow is firstly developed at the University of Kentucky. This code is the fluid dynamics module of known as Kentucky Aerothermodynamics and Thermal Response System (KATS). The solver uses a second-order finite volume approach to solve the laminar Navier– Stokes equations, species mass conservation and energy balance equations for flow in chemical and thermal non-equilibrium state, and a fully implicit first-order backward Euler method for the time integration. The hypersonic flow solver is then extended to account for very low Mach number flow using the preconditioning and switch of …

Shape Memory Behavior Of Single Crystal And Polycrystalline Ni-Rich Nitihf High Temperature Shape Memory Alloys, Sayed M. Saghaian

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf shape memory alloys have been receiving considerable attention for high temperature and high strength applications since they could have transformation temperatures above 100 °C, shape memory effect under high stress (above 500 MPa) and superelasticity at high temperatures. Moreover, their shape memory properties can be tailored by microstructural engineering. However, NiTiHf alloys have some drawbacks such as low ductility and high work hardening in stress induced martensite transformation region. In order to overcome these limitations, studies have been focused on microstructural engineering by aging, alloying and processing.

Shape memory properties and microstructure of four Ni-rich NiTiHf alloys (Ni50.3Ti29.7Hf20, Ni50.7Ti29.3Hf20, …

2015 Zips Sae Baja Brakes And Throttle System, Philip A. Bennett

Williams Honors College, Honors Research Projects

The SAE Baja student design team at The University of Akron is one of the longest-standing design teams at the university. The purpose of this team is to design, manufacture, test, and race an off-road vehicle within the guidelines of competition established by the Society of Automotive Engineers. The vehicle is made up of a small number of subsystems including frame, drivetrain, suspension, steering, and braking. The following will discuss all aspects of the design process of the braking and throttle system of the 2015 Zips Baja car. This process includes several steps and considerations such as design goals, system …

La0.6Sr1.4Mno4+Δ Layered Perovskite Oxide: Enhanced Catalytic Activity For The Oxygen Reduction Reaction, Yarong Wang, Zhibin Yang, Fanliang Liu, Chao Jin, Jiao Wu, Ming Shen, Ruizhi Yang, Fanglin Chen

Faculty Publications

Efficient electrocatalysts for the oxygen reduction reaction (ORR) is a critical factor to influence the performance of lithium–oxygen batteries. In this study, La_0.6Sr_1.4MnO_4+δ layered perovskite oxide as a highly active electrocatalyst for the ORR has been prepared, and a carbon-coating layer with thickness <5 nm has been successfully introduced to enhance the electronic conductivity of the as-prepared oxide. XRD, XPS, Raman, SEM and TEM measurements were carried out to characterize the crystalline structure and morphology of these samples. Rotating ring-disk electrode (RRDE) technique has been used to study catalytic activities of the as-prepared catalysts for the ORR in 0.1 M KOH media. RRDE results reveal that carbon-coated La_0.6Sr_1.4MnO_4+δ exhibits better catalytic activity for the ORR. For the carbon-coated La_0.6Sr_1.4MnO_4+δ, the ORR proceeds predominately via a direct four electron process, and a maximum cathodic current density of 6.70 mA cm⁻² at 2500 rpm has been obtained, …

Design Of An Sae Baja Racing Off-Road Vehicle Powertrain, Eric T. Payne

Williams Honors College, Honors Research Projects

No abstract provided.

La0.7Sr0.3Fe0.7Ga0.3O3-Δ As Electrode Material For A Symmetrical Solid Oxide Fuel Cell, Zhibin Yang, Yu Chen, Chao Jin, Guoliang Xiao, Minfang Han, Fanglin Chen

Faculty Publications

In this research, La_0.7Sr_0.3Fe_0.7Ga_0.3O_3−δ (LSFG) perovskite oxide was successfully prepared using a microwave-assisted combustion method, and employed as both anode and cathode in symmetrical solid oxide fuel cells. A maximum power density of 489 mW cm⁻² was achieved at 800 °C with wet H₂ as the fuel and ambient air as the oxidant in a single cell with the configuration LSFG|La_0.8Sr_0.2Ga_0.83Mg_0.17O_3−δ|LSFG. Furthermore, the cells demonstrated good stability in H₂ and acceptable sulfur tolerance.

Stabilizing Electrochemical Carbon Capture Membrane With Al2O3 Thin-Film Overcoating Synthesized By Chemical Vapor Deposition, Jingjing Tong, Fengzhan Si, Lingling Zhang, Jie Fang, Minfang Han, Kevin Huang

Faculty Publications

Development of high-efficiency and cost-effective carbon capture technology is a central element of our effort to battle the global warming and climate change. Here we report that the unique high-flux and high-selectivity of electrochemical silver-carbonate dual-phase membranes can be retained for an extended period of operation by overcoating the surfaces of porous silver matrix with a uniform layer of Al₂O₃ thin-film derived from chemical vapor deposition.

Investigation Of The Quenching Characteristics Of Steel Components By Static And Dynamic Analyses, Pratik Sarker

LSU New Orleans Theses and Dissertations

Machine components made of steel are subjected to heat treatment processes for improving mechanical properties in order to enhance product life and is usually done by quenching. During quenching, heat is transferred rapidly from the hot metal component to the quenchant and that rapid temperature drop induces phase transformation in the metal component. As a result, quenching generates some residual stresses and deformations in the material. Therefore, to estimate the temperature distribution, residual stress, and deformation computationally; three-dimensional finite element models are developed for two different steel components – a spur gear and a circular tube by a static and …

Modal Characterization And Structural Dynamic Response Of A Crane Fly Forewing, Jose E. Rubio

LSU New Orleans Theses and Dissertations

This study describes a method for conducting the structural dynamic analysis of a crane fly (family Tipulidae) forewing under different airflow conditions. Wing geometry is captured via micro-computed tomography scanning. A finite element model of the forewing is developed from the reconstructed model of the scan. The finite element model is validated by comparing the natural frequencies of an elliptical membrane with similar dimensions of the crane fly forewing to its analytical solution. Furthermore, a simulation of the fluid-structure interaction of the forewing under different airflows is performed by coupling the finite element model of the wing with a …

Utilizing Failure Information For Mission Assessment And Optimization For Complex Systems, Charlie Destefano

Graduate Theses and Dissertations

This paper presents a new failure analysis method, Failure Identification for Mission Analysis (FIMA), which performs a general failure analysis for the overall state of a system, as well as a mission-specific analysis that identifies how failures may have differing effects on the various mission tasks that a system must complete. The FIMA method is capable of being implemented at any point in the design process. During early design stages, the FIMA method will identify various qualitative failure scenarios based on programmed functional relationships and any number of initial failures wished to be simulated. The functional relationships for this method …

Cold Roll Extrusion Machine Redesign Final Design Report, Foja Bains, Bryan Cyr, David Van Schooten

Mechanical Engineering

This report is a comprehensive review of a redesign of subsystems for a Cold Roll Extrusion Machine, a forging operation, for PCC Rollmet. Three subsystems were addressed in this project: A new Loading system, Feed system, and Lubrication system. The Loading system, and support system during developmental design stages, addressed the timely loading process of pipes onto the forging machine. After two quarters of design iteration, the group decided on a lever arm, hydraulic actuated, loading design. In the final quarter of the project, a quarter scale model of this lever arm was constructed to prove the concept of the …

Highly Transparent, Self-Cleaning, And Antireflective Nanoparticle Coatings, Corey Seth Thompson

Graduate Theses and Dissertations

Current solar panel technologies require a sheet of glass to serve as both mechanical support and to protect the cells from the environment. The reflection from the glass sheet can reflect up to 8% of the incident light, reducing the power output of the panel. Antireflective coatings can be used to allow more light to enter the panel to be converted into usable electricity. However, no solid thin film materials exhibit a low enough index of refraction to serve as antireflective coatings for common solar glass. The main goal of this research was to investigate the self-cleaning, antifogging, and antireflective …

Direct Synthesis Of Methane From Co2-H2O Co-Electrolysis In Tubular Solid Oxide Electrolysis Cells, Long Chen, Fanglin Chen, Changrong Xia

Faculty Publications

Directly converting CO₂ to hydrocarbons offers a potential route for carbon-neutral energy technologies. Here we report a novel design, integrating the high-temperature CO₂–H₂O co-electrolysis and low-temperature Fischer–Tropsch synthesis in a single tubular unit, for the direct synthesis of methane from CO₂ with a substantial yield of 11.84%.

Synthesis And Formation Mechanism Of Cuins2 Nanocrystals With A Tunable Phase, Chao Yu, Linlin Zhang, Long Tian, Dan Liu, Fanglin Chen, Cheng Wang

Faculty Publications

Chalcopyrite CuInS₂ (CIS) hierarchical structures composed of nanoflakes with a thickness of about 5 nm were synthesized by a facial solvothermal method. The thermodynamically metastable wurtzite phase CIS would be obtained by using InCl₃ instead of In(NO₃)₃ as In precursor. The effects of the In precursor and the volume of concentrated HCl aqueous solution on the phases and morphologies of CIS nanocrystals have been systematically investigated. Experimental results indicated that the obtained phases of CIS nanocrystals were predominantly determined by precursor-induced intermediate products. The photocatalytic properties of chalcopyrite and wurtzite CIS in visible-light-driven degradation of …

Host-Guest Interaction Dictated Selective Adsorption And Fluorescence Quenching Of A Luminescent Lightweight Metal-Organic Framework Toward Liquid Explosives, Dan Liu, Xiaojuan Liu, Yongxin Liu, Yang Yu, Fanglin Chen, Cheng Wang

Faculty Publications

In this article, we report the successful preparation of a Mg-based luminescent MIL-53 metal–organic framework (MOF), namely [Mg2(BDC)2(BPNO)]·2DMF (1) (BDC = 1,4-benzene dicarboxylate, BPNO = 4,4’- dipyridyl-N,N’-dioxide, DMF = N,N-dimethylformamide) in a mixed solvent containing a 2 : 3 volume ratio of DMF and ethanol (EtOH) under solvothermal conditions. Desolvated compound 1a can be used as an absorbent for selective adsorption and separation of liquid explosives, including nitroaromatic (nitrobenzene (NB)) and nitroaliphatic (nitromethane (NM) and nitroethane (NE)) compounds, through single crystal-to-single crystal (SC–SC) transformations. As one of the weakly luminescent MOFs, the luminescence of compound 1a could be quenched by …

Simulations Of Diffusion Driven Phase Evolution In Heterogenous Solids, Subramanya Gautam Sadasiva

Open Access Dissertations

With reduction in size, ever greater operational demands are placed on electronics components at all levels of the device, starting from the transistor level to the level of the package and the solder interconnects. Concurrently, there has been a move to more complicated materials systems in order to meet health and environmental guidelines. These trends of reducing size, increasing loads have increased the necessity to understand the mechanisms of the failure. ^ As the length scales are reduced, it becomes increasingly important to consider interfacial and micro-structural effects that can be safely ignored at larger length scales owing to the …

Team Nathan Suspension, Frankie J. Wiggins, Alex D. Seitz, Justin P. Bautista

Mechanical Engineering

Nathan Cooper is an 8-year old boy with Spinal Muscular Atrophy (SMA). SMA has affected Nathan’s muscle development and requires him to use the Standing Dani™ mobility device. The Standing Dani is a motorized standing wheelchair, or Wheelstand. Nathan controls and uses it to get around. Though the Standing Dani performs well for most functions, it has some distinct issues. The primary issue that this project addresses is its lack of suspension and the discomfort that Nathan feels as a result. After talking with our client, we developed several specifications generally related to geometry, safety, vehicle dynamics, and reliability. Many …

Microstructure Development Of Granular System During Compaction, Chen Shang, Marcial Gonzalez

The Summer Undergraduate Research Fellowship (SURF) Symposium

Granular materials is the second most manipulated material in the industry today. They are easy to transport and more and more newly developed materials cannot stand the process of traditional casting, like energetic materials and bio-materials, but will survive the powder compaction process. Having a better understanding of the microstructure development of granular systems during compaction process, especially for particles that will heavily deform under loading, will give an insight of how to better process the powders to produce materials with overall better performance comparing to bulk materials. The main theory and mechanism applied are Hertz law and nonlocal contact …

Atomistic Simulation And Virtual Diffraction Characterization Of Alumina Interfaces: Evaluating Structure And Stability For Predictive Physical Vapor Deposition Models, Shawn Patrick Coleman

Graduate Theses and Dissertations

The objectives of this work are to investigate the structure and energetic stability of different alumina (Al₂O₃) phases using atomistic simulation and virtual diffraction characterization. To meet these objectives, this research performs molecular statics and molecular dynamics simulations employing the reactive force-field (ReaxFF) potential to model bulk, interface, and surface structures in the θ-, γ-, κ-, and α-Al₂O₃ system. Simulations throughout this study are characterized using a new virtual diffraction algorithm, developed and implemented for this work, that creates both selected area electron diffraction (SAED) and x-ray diffraction (XRD) line profiles without assuming …

Electroencephalography(Eeg) Data Collection And Processing Through Machine Learning, Jayshree Desai

Graduate Theses and Dissertations

Machine learning methods are an excellent way for understanding the neural basis of human decision making. Some machine learning systems try to eradicate the need for human intuition in data analysis whereas others embrace a collective approach between humans and machines. The objective of this project is to collect Electroencephalography (EEG) signals through wireless sensors, and the process the collected signals through machine learning methods. The EEG data is collected using three EEG electrodes, each being the positive, negative and ground terminals respectively. Since the signal measures in the unit of micro-volts it needs to be amplified using amplifier circuit. …

Understanding The Effects Of Blast Wave On The Intracranial Pressure And Traumatic Brain Injury In Rodents And Humans Using Experimental Shock Tube And Numerical Simulations, Aravind Sundaramurthy

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Blast induced neurotrauma (BINT) has been designated as the “signature injury” to warfighters in the recent military conflicts. In the past decade, conflicts in Iraq (operation Iraqi freedom) and Afghanistan (operation enduring freedom) as well as the increasing burden of the terrorism around the world resulted in an increased number of cases with blast Traumatic Brain Injury (bTBI). Recently, a lot of research has been done to study the neurological and neurochemical degenerations resulting from BINT using animal models especially rat models. However, it is not clear how and whether the biological outcomes from animal models can be translated to …

Transverse Compression Of High-Performance Ballistic Fibers, Zherui Guo

Open Access Theses

High performance ballistic fibers have been in use for decades, specifically in protective applications against ballistic impact such as bulletproof vest layers and aircraft turbine engine fragmentation barriers. These high performance fibers have extremely high strength-to-weight ratios and high moduli of elasticity in the axial direction, making them extremely suitable for high impact situations. In particular, para-phenyleneterephthalamide (PPTA for short) fibers such as Kevlar^® and ultra-high-molecular-weight polyethylene fibers such as Dyneema^® are amongst the more popular high performance fibers in today's world. While the longitudinal mechanical response of these fibers have been extensively researched, their transverse mechanical response …

An Experimental Fatigue And Finite Element Study Of A Welded Joint Of A Snowplow Blade, George Ernest Selburg

Master's Theses (2009 -)

This study describes a method to evaluate the fatigue life of a welded joint of a snowplow. Fatigue specimens were then fabricated, which simulated the joint and its loading characteristics. The joint in the specimens were characterized by measuring the geometry of the weld and the hardness of the parent material, weld material, and heat affected zone. It was determined that the fatigue crack that developed in the joint was exposed to mode I fracture forces in the normal plane of the crack. The specimens were then tested in a hydraulic closed looped system to determine the mechanism of fatigue …

Meshless Mechanics And Point-Based Visualization Methods For Surgical Simulations, Rifat Aras

Computational Modeling & Simulation Engineering Theses & Dissertations

Computer-based modeling and simulation practices have become an integral part of the medical education field. For surgical simulation applications, realistic constitutive modeling of soft tissue is considered to be one of the most challenging aspects of the problem, because biomechanical soft-tissue models need to reflect the correct elastic response, have to be efficient in order to run at interactive simulation rates, and be able to support operations such as cuts and sutures.

Mesh-based solutions, where the connections between the individual degrees of freedom (DoF) are defined explicitly, have been the traditional choice to approach these problems. However, when the problem …

Phonon Confinement Using Spirally Designed Elastic Resonators In Discrete Continuum, Sourav Banerjee, Raiz U. Ahmed

Faculty Publications

Periodic and chiral orientation of microstructures, here we call phononic crystals, have extraordinary capabilities to facilitate the innovative design of new generation metamaterials. Periodic arrangements of phononic crystals are capable of opening portals of non-passing, non-dispersive mechanical waves. Defying conventional design of regular periodicity, in this paper spirally periodic but chiral orientation of resonators are envisioned. Dynamics of the spirally connected resonators and the acoustic wave propagation through the spirally connected multiple local resonators are studied using fundamental physics. In present study the spiral systems with local resonators are assumed to be discrete media immersed in fluid. In this paper …

Redox Stable Anodes For Solid Oxide Fuel Cells, Guoliang Xiao, Fanglin Chen

Faculty Publications

Solid oxide fuel cells (SOFCs) can convert chemical energy from the fuel directly to electrical energy with high efficiency and fuel flexibility. Ni-based cermets have been the most widely adopted anode for SOFCs. However, the conventional Ni-based anode has low tolerance to sulfur-contamination, is vulnerable to deactivation by carbon build-up (coking) from direct oxidation of hydrocarbon fuels, and suffers volume instability upon redox cycling. Among these limitations, the redox instability of the anode is particularly important and has been intensively studied since the SOFC anode may experience redox cycling during fuel cell operations even with the ideal pure hydrogen as …

Folding Wheelchair Improvement, Matthew Edison Grace, Kevin Alan Miyamoto, Andrey Lee Oliveira

Mechanical Engineering

No abstract provided.

Friction Test Machine, Kyle Raymon Schless, Lynda Beatriz Tesillo, Mustapha Nadri

Mechanical Engineering

No abstract provided.

Lightweight Uav Launcher, Ben Miller, Christian Valoria, Corinne Warnock, Jake Coutlee

Mechanical Engineering

This report discusses the design, construction, and testing of a lightweight, portable UAV launcher. There is a current need for a small team of soldiers to launch a US Marine Tier II UAV in a remote location without transport. Research was conducted into existing UAV launcher designs and the pros and cons of each were recorded. This research served as a basis for concept generation during the initial design development stage. It was required that the design weigh less than 110 lbs, occupy a smaller volume than 48" x 24" 18" in its collapsed state, be portable by a single …