Applied Mechanics Commons^™

Computational Modeling Of Torque Arm And Load Cell Interactions In Uta Racing Brake Dynamometer, Anthony A. Aiyedun

2025 Spring Honors Capstone Projects - Archive

The UTA Racing Team is developing a brake dynamometer to measure the coefficients of friction of various brake pads and calipers under controlled conditions. The dynamometer simulates on-track braking scenarios, testing brake pads at temperatures up to 1300ºF and pressures similar to racing environments. Its primary goal is to generate accurate friction vs. temperature graphs for various brake pad and rotor combinations, addressing the need for dedicated testing equipment. This project creates an ANSYS simulation of the torque arm and load cell interaction. The computational model accurately represents the relationship between applied torque and measured load cell force, incorporating precise …

An In-Situ Method For Quantifying Entropy Generation In Fatigue Via A Novel Thermographic Approach, Peyton J. Wilson

LSU Master's Theses

This work features a new approach that is used to measure the rate of plastic work during a cyclic fatigue test, based on the first and second laws of thermodynamics. Using the one-dimensional Fourier heat equation coupled with the concept of fracture fatigue entropy, the rate of plastic work during fatigue can be measured without the need to interrupt a fatigue test, and the accumulated entropy to failure can be quantified. Experimental fatigue tests are conducted on Aluminum 6061-T6 specimens under cyclic axial loading and Carbon Steel 1018 specimens under fully reversed cyclic bending loading. The obtained results in addition …

Hendrickson Lift Kit, Matthew Rozmajzl

Williams Honors College, Honors Research Projects

This research project will be completed with Hendrickson Trailer as the sponsor. The goal of the project is to create a lift kit for a newer suspension system. The lift kit must provide enough lift force to lift an axle off the road and suspend it off the road while in transit. There are similar systems offered for different products at Hendrickson, but the configuration of this system is such that new brackets must be designed. The benefit of such a system is a reduction in wear on the lifted tires, and thus an increase in the life of the …

Structural Sizing Of Post-Buckled Thermally Stressed Stiffened Panels, Walid Arsalane

Theses and Dissertations

Design of thermoelastic structures can be highly counterintuitive due to design-dependent loading and impact of geometric nonlinearity on the structural response. Thermal loading generates in-plane stresses in a restrained panel, but the presence of geometric nonlinearity creates an extension-bending coupling that results in considerable transverse displacement and variation in stiffness characteristics, and these affects are enhanced in post-bucking regimes. Herein a methodology for structural sizing of thermally stressed post-buckled stiffened panels is proposed and applied for optimization of the blade and hat stiffeners using a gradient-based optimizer. The stiffened panels are subjected to uniform thermal loading and optimized for minimum …

Prediction Of In-Plane Stiffnesses And Thermomechanical Stresses In Cylindrical Composite Cross-Sections, Bryson M. Chan

Master's Theses

Accurate mechanical analysis of composite structures is necessary for the prediction of laminate behavior. Cylindrical composite tubes are a mainstay in many structural applications. The fundamental design of circular composite cross-sections necessitates the development of a comprehensive composite lamination theory. A new analytical method is developed to characterize the behavior of thin-walled composite cylindrical tubes using a modified plate theory. A generated numerical solver can predict properties such as axial stiffness, bending stiffness, layer stresses, and layer strains in composite tubes subjected to combined mechanical loading and thermal effects. The model accounts for the curvature by transforming and translating the …

Enduro Campers, Ryan J. Shomsky, Alexander W. Horst, Kevin S. Pickering, Jackson L. Aplanalp, Luke Arana, Will Firestone

Mechanical Engineering

The Enduro Campers senior project team (Formerly known as Lobo Campers senior project team) was recruited by Mr. Leif Stein to assist in the design, manufacturing, and testing of the materials and components of his company’s expedition box camper. The two main focuses of the project, divided into two sub-teams, were on the testing and manufacturing process of the materials used in the camper, and on the design and analysis of the camper’s access door, step box, and other subsystems.

The focus of the materials analysis and manufacturing team was based around the design parameter to use composite sandwich panels …

A Single-Stage Passive Vibration Isolation System For Scanning Tunneling Microscopy, Toan T. Le

Master's Theses

Scanning Tunneling Microscopy (STM) uses quantum tunneling effect to study the surfaces of materials on an atomic scale. Since the probe of the microscope is on the order of nanometers away from the surface, the device is prone to noises due to vibrations from the surroundings. To minimize the random noises and floor vibrations, passive vibration isolation is a commonly used technique due to its low cost and simpler design compared to active vibration isolation, especially when the entire vibration isolation system (VIS) stays inside an Ultra High Vacuum (UHV) environment. This research aims to analyze and build a single-stage …

On The Stress Concentration At Sharp V-Notches Under Tension, Trent Mattieu Andrus

LSU Master's Theses

Accurately determining stresses at re-entrant corners using finite element analysis (FEA) is challenging due to the high stresses produced at the corner. Indeed, FEA is unable to obtain quantitatively accurate peak stresses at mathematically sharp re-entrant corners with traditional boundary conditions because these stresses are singular. Imposing a local corner radius by rounding the sharp corner to remove the singular result is an appropriate technique for large radii, but as the corner radius tends to zero and the notch is close to being sharp, we expect there are radii that yield quantitatively inaccurate results with traditional FEA. We seek to …

Design Of Structural Stand For High-Precision Optics Microscopy, Sara T. Novell

Master's Theses

Lawrence Livermore National Lab (LLNL) is home to the National Ignition Facility (NIF), the world’s largest and most energetic laser. Each of the 192 beamlines contains dozens of large optics, which require offline damage inspection using large, raster-scanning microscopes. The primary microscope used to measure and characterize the optical damage sites has a precision level of 1 µm. Mounted in a class 100 clean room with a raised tile floor, the microscope is supported by a steel stand that structurally connects the microscope to the concrete ground. Due to ambient vibrations experienced in the system, the microscope is only able …

Investigation Of Design, Manufacture, Analysis, And Test Of A Composite Connecting Rod Under Compression, Thomas Juhl Rohrbach

Master's Theses

Composite materials hold great potential for the replacement of traditional materials in machines utilized on a daily basis. One such example is within an engine block assembly where massive components inherently reduce the efficiency of the system they constitute. By replacing metal elements such as connecting rods, cylinder caps, or a crank shaft with composite alternatives, a significant increase in performance may be achieved with respect to mechanical strength, thermal stability, and durability, while also reducing mass. Exploration of this technology applied to a connecting rod geometry was investigated through a combination of process development, manufacturing, numerical analysis and testing. …

Reinventing The Wheel, Esther K. Unti, Ahmed Z. Shorab, Patrick B. Kragen, Adam M. Menashe

Mechanical Engineering

Reinventing the Wheel selected tires and designed wheels for the 2018 Cal Poly, San Luis Obispo Formula SAE combustion vehicle. Available tire options were evaluated for steady-state and transient performance as well as vehicle integration. A single-piece composite wheel with hollow spokes was designed to meet stiffness, strength, and tolerance requirements. A detailed study of wheel loading and geometric structural efficiency was performed. Finite element analysis was used to iterate the geometry and laminate. A two-piece male mold was designed and machined to manufacture the wheel. Removable silicone inserts were used to create the hollow spokes.

Universal Studios Hollywood Vip Trolley - Roller Frame, Jeffrey Ploss, Chase Montague, Lincoln Treanor

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Rotordynamic Analysis Of Theoretical Models And Experimental Systems, Cameron R. Naugle

Master's Theses

This thesis is intended to provide fundamental information for the construction and

analysis of rotordynamic theoretical models, and their comparison the experimental

systems. Finite Element Method (FEM) is used to construct models using Timoshenko

beam elements with viscous and hysteretic internal damping. Eigenvalues

and eigenvectors of state space equations are used to perform stability analysis, produce

critical speed maps, and visualize mode shapes. Frequency domain analysis

of theoretical models is used to provide Bode diagrams and in experimental data

full spectrum cascade plots. Experimental and theoretical model analyses are used

to optimize the control algorithm for an Active Magnetic Bearing …

A 2-D Finite Element Modeling And Simulation Of 3-Roll Forming, Wenbo Zhao

LSU Master's Theses

Medium to large diameter carbon steel pipes are widely used in various applications such as gas and fluid transportation, tunnels construction and building construction. Based on manufacturing techniques and characteristics, they are mainly categorized into three categories: Seamless pipe, Butt-welded pipe and Spiral pipe. The forming of butt-welded and spiral pipe is often performed by a technique called 3-roller bending. While traditional trial-and-error method is costly, the geometry complexity, along with material nonlinearity makes exact theoretical analysis difficult unless heavy simplified assumptions are made. While the forming parameters in the 3-roller forming process of butt-welded pipe has been studied in …

Fea Analysis And Optimization Of Differential Housing For Fatigue Stresses And Fatigue Test Design To Study Skin Effect In Ductile Iron, Swapnil A. Pandey

Dissertations, Master's Theses and Master's Reports

Automotive emission standards are getting more stringent day by day and governments worldwide are moving to reduce emissions from automobiles. In this scenario reducing the weight of automobile components becomes an important design objective to reduce emissions. A 10% reduction of weight in the complete automobile leads to 6-8 percent improvement in mileage (Mhapankar 2015). Also, powertrain components make up for approximately 27% of the total automobile weight and thus optimizing the design of components in the powertrain is an important task (Mhapankar 2015). Statistics show that 26% of component failures in automobiles are part of powertrain and 21% of …