Applied Mechanics Commons^™

A Maximum Energy Release Rate Computational Framework For Fatigue Crack Trajectory And Life Prediction Under Mixed-Mode Proportional And Nonproportional Loading, Nahla Helmy Matar

Theses and Dissertations

The problem of mixed-mode fatigue crack growth has been a persistent research challenge. The determination of fatigue crack propagation direction directly impacts the safety and integrity of components and structures, making it crucial in various industrial applications, including welded drilling pipes, aerospace, and automotive engineering. Unlike uniaxial loading, mixed-mode cracks tend to change direction frequently (kinking), and nonproportional loading adds to the complexity of the problem. This research aims to estimate the crack propagation direction and fatigue crack life in linear elastic materials subjected to mixed-mode (I+II) loading conditions under proportional or non-proportional cyclic loading. Numerical software was developed based …

Structural Design And Finite Element Analysis Of A 54 Ton Freight Wagon Bolster Test Rig Under Vertical Center Plate Load, Shandy Dwi Prayoga, I Dewa Gede Ary Subagia, I Ketut Adi Atmika, Abdul Rohman Farid, Yunior Lanang Satrio

Journal of Mechanical Engineering Science and Technology (JMEST)

Bolster is one of the bogie's components that receives direct loading from the car body and freight movement. One of the problems that occurs in the bolster is permanent deflection during vertical and transversal static loading. Therefore, a static loading test is required to evaluate the structural strength of the bolster. During the static loading test, a rig is required to hold the bolster so that the bolster is in a fixed position. The rig owned by PT. INKA (Persero) showed a plastic deformation at the vertical center plate load (VCP 5.22P). Therefore, a modified design of the rig is …

Magnetic Field-Induced Transformation In Polycrystalline Ni2mnal Heusler Type Magnetic Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely, Laura N. Bartlett

Materials Science and Engineering Faculty Research & Creative Works

The martensitic and magnetic transformations, as well as the mechanical properties, of Ni₂MnAl alloys in as-cast (AC) and heat-treated (HT) conditions were investigated. Magnetic-field-induced strain was evaluated via magnetostriction, with reversible strains of 0.14% and 0.2% achieved in the martensitic phase at 2 K for the AC and HT alloys, respectively. Transformation temperatures and Curie temperatures were determined under constant applied magnetic field, revealing that γ-phase inclusions in the AC microstructure suppress antiferromagnetic domain response, yielding a lower magnetization (∼8.4 emu g⁻¹) compared to the HT alloy (∼13.4 emu g⁻¹). Both alloys exhibited hysteretic behavior in the martensitic state and …

Optimization And Energy Efficiency Analysis Of An Automatic Feed Mixer With A Rotating Drum Mechanism, Kris Witono, Talifatim Machfuroh, Nurlia Pramita Sari, Lisa Agustriyana, Aini Lostari

Journal of Mechanical Engineering Science and Technology (JMEST)

Energy-efficient feed mixer machines are important for improving the productivity and sustainability of small and medium-scale livestock farms. Previous studies primarily focused on either structural performance or mixing efficiency, with limited studies integrating both aspects. Therefore, this study evaluated an automatic rotating-drum feed mixer by combining Finite Element Method (FEM) analysis and energy modeling. The study used FEM simulations for different materials, namely A36 steel alloy, stainless steel 304, aluminium 6061, and galvanized steel, with thicknesses of 3 mm and 4 mm, as well as different drum systems. The FEM results showed that all evaluated materials met the minimum safety …

An Analytical Framework For Quantifying Urban And Community Resilience To Natural Hazards From Cell-Phone Gps-Location And Traffic-Flow Data, Georgios Chatzikyriakidis

Civil and Environmental Engineering Theses and Dissertations

Urban areas are increasingly exposed to natural hazards while accommodating a growing share of the global population, yet a consistent science-based framework for quantifying urban and community resilience remains lacking. This dissertation develops a physics-based analytical framework grounded in statistical mechanics and the quantitative theory of Brownian motion. A city is conceptualized as a complex medium in which citizens move analogously to Brownian particles within a viscoelastic environment, influenced by socioeconomic interactions and infrastructure functionality.

A central premise is that urban resilience, interpreted as engineering resilience (an outcome), can be quantified through a single metric: the mean-square displacement MSD=⟨r²(t)⟩, of …

Recycling 3d Printing Waste In The Binghamton University Makerlab, Kevin Tejera

Library Research Scholars Program Spring 2026

3D printing is an important part of many university makerspaces. However, it comes with negative environmental consequences, including polylactic acid (PLA) filament waste. Currently, the MakerLab at Binghamton University has no closed-loop recycling system, leading to large quantities of used filament being sent to landfills, where it contributes to greenhouse gases and microplastic production.

This research project looks at the feasibility of an in-house PLA filament recycling program by examining the mechanical recycling process, cost/equipment needs, contamination issues, available space, and the effect of repeated recycling on the filament. An economic analysis will be completed through a break-even analysis and …

Interplay Between Phase Instability And Deformation Mechanisms In Beta Titanium Alloys In Aggressive Environments, Benjamin Elbrecht

All Dissertations

Modern designs, such as commercial jet turbines, are reliant on the high temperature performance of their constituent materials. Improvements to the strength-at-temperature of materials are critical to the continued advancement of efficiency and payload capacity in these advanced applications. This dissertation presents studies that progress towards this goal through the construction of a new experimental setup for complex temperature and force profiles that also accurately captures deformation behavior through non-contact measurements. Using this setup, studies into two specialty titanium alloys were executed: discovering the microscopic mechanisms responsible for the macroscale behavior and testing in conditions closely replicating aircraft turbine operating …

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy

Materials Science and Engineering Faculty Research & Creative Works

Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Critical Parameters Controlling Oxide Scale Formation And Hydro-Descaling Efficiency During Steelmaking, Tochukwu Princewill Ojiako

Doctoral Dissertations

In modern steelmaking, cast slabs are exposed to high-temperature oxidizing environments during secondary cooling, reheating, and hot rolling, resulting in the formation of multilayer oxide scales on the steel surface. These scales interact with mold-flux residues originating from the casting process (CC). The morphology, chemistry, and adhesion of oxide scale strongly influence its removability during high-pressure hydraulic descaling and ultimately determine the surface quality of hot-rolled products. However, the mechanistic relationship between oxide scale evolution, scale-steel interfacial structure, and hydraulic descaling performance remains poorly understood.

This dissertation investigates oxide scale formation, modification, and removal in low-carbon thin-slab steels produced by …

Castrip Process Technology: Non-Grain Oriented (Ngo) Si Steels Extension And Carbide-Free Bainitic (Cfb) For Flat Products, Naram Naidu Meesala

Masters Theses

"This research explores the development of advanced steel grades manufactured through Castrip® twin-roll thin strip casting technology, with particular attention to non-grain-oriented electrical Si-Steels (NGOES) and carbide-free bainitic (CFB) steels. The Castrip® process offers a near-net-shape route for producing thin steel strips, which greatly decreases the number of processing stages, lowers energy demand, and reduces carbon dioxide emissions when compared with traditional steel production methods.

In the NGOES part of the study, several industrial Fe–Si steel compositions were cold rolled to final thicknesses ranging from 0.35 mm to 0.15 mm. These materials were then exposed to short-duration continuous annealing at …

Effect Of Complex Alloying Elements On Oxide Scale Formation And Water-Jet Descaling Performance On Continuously Cast Low-Carbon Steels, Tochukwu P. Ojiako, Tsvetkov Dmitry, Mario Buchely, Haiming Wen, Simon N. Lekakh, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

The formation and evolution of oxide scale in contact with mold flux during continuous casting, subsequent reheating, and hydraulic descaling are strongly governed by steel chemistry. To elucidate the effect of complex alloying elements (Si, Mn, and Cr), two industrially produced continuously cast low-carbon steel grades for manufacturing stamped parts (a base and alloyed steel grade) were investigated. The objective was to determine how alloying elements influence oxidation behavior, scale morphology, interfacial adhesion, and water-jet descaling efficiency. Continuously cast slab specimens were subjected to controlled thermal and atmospheric oxidation cycles simulating multistage industrial practice. Three initial surface conditions (industrial as-cast, …

Predicting Long-Term Creep Behavior Using Short-Term Stress Relaxation Data In Expanded Polyethylene Foam, Andrew M. Seelig

All Theses

Closed cell expanded polyethylene (EPE) foams are widely used for protective packaging due to their high energy absorption properties and recyclability. However, these foams can be subjected to sustained compressive stresses (13.78 - 36.20 kPa), depending on density and application, leading to time-dependent deformation (creep). Creep reduces cushioning performance, making its understanding critical for effective protective packaging. Two standards, ASTM D3575 and ASTM D2221, define methods for conducting compressive creep tests on foam materials, with test durations extending up to 1000 hours. Accelerated methods such as Time Temperature Superposition (TTS) and the Stepped Isostress Method (SSM) have been explored for …

Reduced Order Approach For Peening Stress Field Variability, Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

A common goal in shot peening research is to connect operational parameters to resultant residual stress fields, providing a means to control and optimize the effectiveness of surface treatment. In practice, experimental measurements of residual stresses are often averaged values over regions that are large in comparison to an impact dimple. In fact, the stochastic nature of impact locations leads to residual stress fields that are distributed. Finite element peening simulations confirm this observation. The goal of this report is to connect operational parameters to localized fluctuations in residual stress through probabilistic reasoning (Figure 1). In particular, the development of …

Investigations On The Fatigue Strength Of Threads Produced By Different Fabrication Techniques, Philippe Du Maire, Jürgen Hoffmeister, Andreas Öchsner, Michael Johlitz

15th International Conference on Shot Peening

The increasing importance of sustainability in engineering demands the development of long-lasting, high-performance components that reduce material and energy consumption over time. This study investigates how different thread manufacturing processes, i.e., cutting, rolling, and deep rolling, affect the fatigue strength of bolts made from 42CrMo4+QT steel. Cylindrical specimens with M12 threads were subjected to cyclic tensile loading with constant mean stress. Fatigue strength was evaluated using the staircase method, and supporting analyses included X-ray diffraction for residual stress, and full width half maximum examination and Vickers microhardness measurements. Results show that thread rolling significantly improves fatigue strength, achieving 113.8 MPa …

Improving Fatigue Strength And Life Of Single Crystal Cmsx-4, Jochen Peter Fuhr, Lloyd Hackel, Nicolau I. Morar, Noah Holtham, Keivan Davami, Montu Sharma, Rajkumar Roy

15th International Conference on Shot Peening

The deep penetration of laser peening (LP) and retention of residual stress at high temperature by LP is significant in improving fatigue life and strength of superalloys exposed to high temperature and corrosion. Single crystal CMSX-4, was evaluated for stress relaxation and both fatigue life and fatigue strength of material that was LP-treated compared to non-LP and shot-peened (SP) specimens. LP was done with multiple layers using a 20 J/pulse laser where the laser high energy enabled using a 5 mm spot size on the metal surface. Stress measurements by the slitting technique showed the plastic penetration depth exceeded SP …

Design Of A 10-Ton Capacity Solar-Powered Cold Storage At The Cituis Fish Auction Site, Tangerang, Banten, Indonesia, Wardi Wardi, Muhammad Arif Budiyanto

Journal of Materials Exploration and Findings

This study presents the design of a 10-ton capacity solar-powered cold storage system for the Cituis Fish Auction Site (TPI) in Tangerang, Indonesia, as a sustainable solution to support the coastal fisheries sector. The system comprises two temperature zones: an anteroom at 5°C and a freezer room at -30°C, both integrated with a hybrid system utilizing solar panels and batteries. The total power consumption of the cooling system reaches 27.51 kW. The simulation results, obtained using HOMER Pro software, indicate that the hybrid PV system can reduce CO₂ emissions by up to 16,754 kg per year. From an economic …

Effect Of Manufacturing And Machining Process On Recycled Composite Connecting Rods Under Tension And Compression, Walter W. Oppelt

Master's Theses

Carbon fiber reinforced polymer (CFRP) is an engineering material renowned for its high-strength and low-density material properties. Such properties make CFRPs especially useful for applications across many industries, including aerospace, automotive, marine, sporting goods, oil and gas, and more. However, with such favorable material properties comes the cost of high energy usage required to produce raw carbon fiber. Recycled carbon fiber (rCF) has emerged as a promising alternative, offering a significant reduction in energy usage. This research explores the viability of applying recycled CFRPs to internal combustion engines to both reduce energy costs during manufacturing and while in use. Mechanical …

Model-Based Design Of Compressed Lithium-Metal Pouch Cell Battery Modules For Evtol Applications, Scott J. Stirling

Master's Theses

Batteries with higher specific energy and power are essential for extending the range and performance of electric vertical takeoff and landing aircraft (eVTOLs). Anode-free lithium-metal pouch cells offer strong potential at the cell-level but require high compressive pressures to enhance cycle life and discharge performance. These pressures necessitate heavier structural components, reducing packaging efficiency at the module level.

To evaluate this tradeoff, a full-factorial enumeration model was developed to explore viable module designs within a constrained packaging volume. The model scales subsystem masses, enforces design rules and material limits, and accounts for large (~20%) cell thickness changes during cycling.

Results …

Adjustable Dynamometer Motor Mount, Garrett Carson Ng, Elijah Siegel Reuven, Ethan Fong, Daniel Larimer

Mechanical Engineering

The Cal Poly Electrical Engineering Department and sponsor Dr. Dolan needs a manufacturable motor fixture that securely aligns motors of various sizes with dynamometers. Previous lab motor fixtures could not accommodate motors of different sizes, making precise alignment between motors and dynamometers time-consuming and unreliable. Our team developed a modular, manufacturable fixture capable of aligning various motor sizes quickly, accurately, and securely, enhancing lab consistency and usability.

Deciphering And Translating Bioinspired Structures For Engineering Materials Design Via Computational Modeling And Machine Learning, Zhangke Yang

All Dissertations

Nature has evolved extraordinary structural materials—such as nacre, bone, and the mantis shrimp’s dactyl club—that achieve remarkable combinations of strength, toughness, and impact resistance. These properties arise from sophisticated synergies between structure and composition. Inspired by these biological systems, this dissertation presents a comprehensive investigation into bioinspired materials, uncovering fundamental mechanisms and providing guidance on designing materials with superior mechanical properties.

This dissertation begins by examining the "brick-and-mortar" structure of nacre, which informs the design of layered polymer-graphene nanocomposite films. Using coarse-grained molecular dynamics simulations, I elucidate mechanisms of dynamic wave propagation and energy dissipation in these systems, providing critical …

Mechanistic Insights Into Polymer-Assisted Graphene Exfoliation: The Roles Of Velocity, Adhesion, Cohesion, Temperature, Peeling Mode, And Edge Defect Via Coarse-Grained Molecular Dynamics, Linjiale Dai

All Theses

Graphene exfoliation is a critical step in the fabrication of high-quality graphene

layers. However, the underlying fracture mechanisms remain poorly understood. In this

work, I employed coarse-grained (CG) molecular dynamics (MD) simulations to

investigate how factors such as interfacial binding energy, substrate cohesion, temperature,

peeling mode, and edge defects influence the outcome of the exfoliation process. To model

polymer-assisted mechanical exfoliation, I used a finite-size system in which multilayer

graphene (MLG) is sandwiched between two thin polymer films. Leveraging the

spatiotemporal efficiency of the CG model, I performed fifty simulation iterations per

parameter set and analyzed the results from a …

Intelligent Turning Cyber-Physical Systems Modeling Using Sysml, Prithbey Raj Dey, David Lee Enke, Mario F. Buchely

Engineering Management and Systems Engineering Faculty Research & Creative Works

Cyber-Physical Systems (CPS) support industrial automation that incorporates people, hardware, signal, computation, and control using networking to achieve desired results. The complex automated CPS design demands a standard and comprehensive approach to appropriately identify the system requirements, define the architecture, and model the relationships among the software and hardware components. Systems Modeling Language (SysML) provides the capability for a comprehensive modeling to capture the desired design requirements in the systems architecture. SysML enables performance estimation of the model by analyzing constraints while identifying interactions among the components through various behavioral diagrams. In this paper, SysML is applied to the design …

Development Of Planetary Drive System For Formula Sae Electric Race Car, Brian Wong, Bradley Maruoka, Joshua Charles Fine, Madison Kai

Mechanical Engineering

Hub motors are compact electric motors mounted directly on each outboard wheel hub. Utilized in Formula SAE and Formula Student vehicles, this configuration offers several advantages over traditional drivetrains, including packaging optimization within the chassis, vehicle traction, and improved efficiency. Although hub motors are not yet common in 4WD vehicles, they are being explored for use in EVs and may become more common in the future. Every year, Cal Poly Racing FSAE designs and builds a formula-style race car. To improve drivetrain performance, the team is investigating the achievability of a hub motor 4WD drivetrain, requiring extensive research, development, and …

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

Analysis Of Ptfe Radial Lip Seals For Wheel Bearing Applications, Madison Vogt

Theses and Dissertations--Mechanical and Aerospace Engineering

A numerical analysis was conducted to investigate the viscoelastic effects of nonlinear materials on the sealing zone and contact pressure distribution of radial lip seals in a conventional geometric topology. The use of nonlinear materials in radial lip seal applications is desirable to improve operation and reliability of rotating machinery due to their high operating temperatures, chemical compatibility, and low friction coefficients. Examples include, but are not limited to, seals within industrial air compressors, turbine engines, aircraft landing systems, chemical processing equipment, and Freon pumps. This work focuses on analyzing the nonlinear viscoelastic response of pure Polytetrafluoroethylene (PTFE) and PTFE …