Applied Mechanics Commons^™

Large Telescope Mount For Long Exposure Photos, Payne M. Landis, Anna J. Gray

Williams Honors College, Honors Research Projects

When viewing the stars through a telescope, it is common that the object you are viewing drifts out of view. Many amateur astronomers seek to capture long exposure images of the stars, planets, and galaxies with commercially available sky tracking telescope mounts. The complication is that these telescope mounts are both incredibly expensive and have low weight limits. These issues limit accessibility to these products based on the telescope. For each person, telescope parameters determine the amount of light and magnification that can be viewed, which then determines exposures time for adequate photo results. The options on the market for …

From Concept To Light: Manufacturing A Dual-Purpose Bedside Lamp And Book Organizer, Nicole Goulet

Honors Theses

This report features the design, development, engineering changes, and manufacturing of the Bedside Lamp, a hand-made multi-purpose lamp, book holder, and charging hub. The investigation began with research and a market analysis on current lamp designs and a discussion about what features would set the lamp apart. This led to the design of the lamp and construction of multiple prototypes for proof of concept.

A manufacturing process was then designed to demonstrate the steps to start up an efficient and cost-effective production line. This process included obtaining raw materials, cutting them into the necessary parts, and assembling everything to create …

A Structural Evaluation And Design Optimization Of A Tow Bar For Disabled Snowmobiles, David M. Pevic

Masters Theses

Snowmobile tow bars are devices used to rigidly connect two snowmobiles, such that a disabled snowmobile can be recovered from a remote location with a working snowmobile. These devices, however, are not widely used or readily available. An existing tow bar design was evaluated and redesigned to improve its structural capacity and performance. This evaluation provided a baseline to quantify improvement and included Finite Element Analysis (FEA), Design Failure Mode and Effect Analysis (DFMEA), and Design for Assembly analysis (DFA). A review of existing snowmobile tow bar patents was also performed. An updated design was then fabricated and similarly evaluated. …

Design And Implementation Of A Vision-Based Deep-Learning Protocol For Kinematic Feature Extraction With Application To Stroke Rehabilitation, Juan Diego Luna Inga

Master's Theses

Stroke is a leading cause of long-term disability, affecting thousands of individuals annually and significantly impairing their mobility, independence, and quality of life. Traditional methods for assessing motor impairments are often costly and invasive, creating substantial barriers to effective rehabilitation. This thesis explores the use of DeepLabCut (DLC), a deep-learning-based pose estimation tool, to extract clinically meaningful kinematic features from video data of stroke survivors with upper-extremity (UE) impairments.

To conduct this investigation, a specialized protocol was developed to tailor DLC for analyzing movements characteristic of UE impairments in stroke survivors. This protocol was validated through comparative analysis using peak …

Rc Baja: Drivetrain And Chassis, Caden Harris

All Undergraduate Projects

The engineers in the CWU Mechanical Engineering Technology program were asked to design and manufacture a remote-controlled Baja car to compete in several different events. The car was required to compete in a drag race, slalom event, and Baja event against other cars created by engineering students. To compete at the highest level, the cars needed to finely balance ruggedness, weight, torque, and top speed.

This report is dedicated to the designing, manufacturing, and testing of the drivetrain and chassis that supported the RC car as it competed in the school-sanctioned competition; a partner was responsible for the steering and …

Jack And Alex Rc-Baja, Alex Vornbrock

All Undergraduate Projects

Teams of two mechanical engineering students were tasked with the construction of an RC Baja car qualified by the rules and regulations of the Baja competition as well as specifications set by the individual team member for their portion of the vehicle. This proposal focuses on the Chassis and Drivetrain of the vehicle while team member Jack Stutz oversaw the steering and suspension. Teams will compete against each other in various modes to determine the best vehicles of the competitors. The chassis was made of standard aluminum, the remaining parts made by the students were made with PLA; both materials …

Rc Baja Suspension And Steering, Garrett Bailey

All Undergraduate Projects

The RC Baja team set out to engineer and construct a working remote-control device that can compete in the ASME Baja Competition. The students have a focus on either suspension and steering or drivetrain and chassis. This report is centered on the suspension and steering. First, multiple analyses were completed using engineering methods such as mechanical design, statics, strengths of materials, and dynamics for parts of the device. The calculations found in the analysis are then used to create designs for the parts so that they will meet the requirements and be successful in the competition. After the parts are …

Jcati Carbon Fiber Recycler: Crusher System, Devin Riley

All Undergraduate Projects

With a substantial rise in Carbon Fiber use across all industries, the need for a way to recycle the waste has grown as well. A group of Mechanical Engineering Technology students at Central Washington University funded by the Joint Center for Aerospace Technology (JCATI) have created a machine to recycle waste wing trimmings from the Boeing company’s airplanes. This machine consists of 5 different sub-assemblies being the oven, crusher, gear train, conveyor, and shredder. The purpose of this project was to decrease the deflection in the crusher caused by bulging in the housing and movement of the bearings. To decrease …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Geometric Iteration Of A Knee Prosthetic And Static Stress-Bearing Capacity, Alexander Wheeler

Honors Program: Senior Projects (Public)

The purpose of this study was to improve a prosthetic knee model in terms of size, weight, and biocompatibility. Several tests were run to determine its effectiveness in supporting static and quasistatic loads. The positions in which these tests were run include static upright standing, static one-knee 90 degree kneeling, static squatting at maximum flexion, and quasistatic midstride. These simulations were conducted to find areas of high stress and strain. These patterns were used to determine the maximum body weight a physical prosthetic could support. The material used to create the prosthetic was changed from AISI 316 stainless steel to …

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

Reactive Archey Target Design Team "Mimic", Brandon Croyle, Jacob Boss, David Rodgers, Austin Wivell

Williams Honors College, Honors Research Projects

This design project will aim to provide archery hunters with a platform to simulate shooting at string jumping deer. String jumping refers to a spooked deer hearing the snap of a bow string and instintivly ducking up to ten inches. This often results in wounded or missed deer. We will design and build a control system that uses the sound of a bow string as a trigger to operate a mechanical target system. A sound sensor will mimic a deer’s hearing in close range hunting and then send a signal to the mechanical system to replicate the dropping motion of …

Recumbent Bicycle Balancing Aid, James Hager

Williams Honors College, Honors Research Projects

For our senior design project, our team will be consulting to create a balancing aid system intended for the recumbent bicycle shown below in Figure 1. The owner of the bicycle is Robert Henderson, a former United States Navy sailor from Northeast Ohio who picked up biking and skiing while he was stationed in Maine in the late 80’s. While there, he took to the mountains on the rugged terrain and brought this passion of biking back home to share with his wife, Johanna once he completed his service to his country. Biking became an integral part of the …

High Accessibility Cabinet Insert, Matthew Leal

All Undergraduate Projects

Watching grandparents and parents get older, the struggle of day-to-day activities generally increases. One of the most recurring issues the older generation experiences nearly daily is their inability to reach dishes, glassware, and other things on the topmost shelves of a kitchen. Not only is it difficult for them to use things such as stepstools, it also becomes increasingly dangerous. With age, a fall from any height could be catastrophic. With this scenario in mind, a user-friendly cabinet insert would be a very effective way to combat this issue. However, many existing models of cabinet designed to fit these requirements …

Mechanical Design And Optimization Of An Interactive Animatronic Bald Eagle, Eric Burns

Phi Kappa Phi Research Symposium (Archived)

Animatronics is a specialized sub-category of mechatronics, a fusion of mechanical and electrical engineering. The field has grown from small, individual projects into a major industry. As animatronics progress, mechanical engineers are pushed to design internal structures which occupy ever-decreasing spaces and to ensure designs can undergo maintenance and modifications smoothly. This research investigates methods of reducing space required for mechanisms and several other beneficial methods of development as well as varying satisfactions for audiences when exposed to actor-controlled systems rather than pre-scripted functions. The mechanical systems are designed using CAD software available at Georgia Southern. On-campus, resources are used …

Orchard Bin Atv Trailer, Neil F. Leitz

All Undergraduate Projects

A local orchardist was experiencing a problem that was being caused by their lack of apple picking bin moving equipment. The orchardist needed a well-engineered solution to this lack of equipment. The solution arrived at was a five bin trailer. There were multiple design requirements for this trailer, including the device needing to be able to interface with an ATV, be able to be loaded by hand, be able to carry five bins, and not exceed a budget of $750. While perfecting the design of the trailer, a number of different disciplines were utilized, which included dynamics, kinematics, static loading …

Multiple Apple Box Lift 1/10th Scale Model, Kyle J. Burlingame

All Undergraduate Projects

Title and Author: 1/10th Scale Multiple Apple Box Lift by Kyle Burlingame (Engineering Technologies, Safety, and Construction) Abstract/Artist statement: A 1/10th scale Multiple Apple Box Lift was designed and built as a proof of concept for a full scale device. The Multiple Apple Box Lift was designed to meet a customer’s requirements and to be presented at SOURCE. This device lifts the top half of the stacked apple boxes on a pallet in order to allow access to the boxes in the middle of the stack. The device can be manually operated by two people while in-between narrow rows of …

Universal Play Frame Vi, Justin Bazant, Cullen Crackel, Anthony Franceschi

Mechanical Engineering

This design report details the design process utilized by Adaptive Exercise Designs (AED) in creating the sixth design of the Universal Play Frame (UPF). The UPF is an adaptive frame which supports a variety of devices that allows athletes in wheelchairs with limited range of motion to participate in physical activity. The past five frame designs do not meet the needs of the Friday Club due to complications with function and time constraints. To ensure all of Fridays Club's needs were met, the problem was better defined by converting the customer requirements into engineering specifications. The design process our team …