Applied Mechanics Commons^™

Development Of A Prototype Satellite-Tracking Telescope For Ground-Based Spectroscopy, Charles Smith

Graduate Theses and Dissertations

Spectroscopy is the practice of determining the chemical composition of a gas through analyzing the light that is filtered by the gas. Spectroscopy is commonly used by astronomers to deduce the atmospheric composition of planets. This process is done by initially measuring the spectrum of light from the star that the planet orbits, and then measuring it again once the planet is in between the observer and the star. The spectrum light that is filtered out is dependent on the chemical composition of the gas, and so this information can be used to determine the chemical composition of the atmosphere …

Understanding Thermal Comfort Impact And Air Movement Around Open Stairs Through The Use Of Cfd Modeling, Ethan Davidson

Graduate Theses and Dissertations

The air exchange between two floors of a building has an impact on thermal comfort. The present research attempts to quantify this impact and identify the contributing factors disrupting the thermal comfort on and around stairs. Various heating and cooling scenarios were analyzed, using CFD modeling, in a simple two-story building separated by a single staircase. The research examines a single building layout with a fixed inlet and outlet configuration. In addition, the study investigated the short-term impact on thermal comfort. As a result, the duration of the simulations varies from two and half minutes to ten minutes, consistent with …

Autonomous Material Refill For Swarm 3d Printing, William C. Jones

Mechanical Engineering Undergraduate Honors Theses

3D printing currently offers robust and cheap rapid prototyping solutions. While standard 3D printing remains at the periphery of mass production, the technology serves as a starting point for the development of swarm manufacturing. Since swarm manufacturing is predicated upon autonomy, swarm technology companies such as AMBOTS are seeking to minimize human involvement in the swarm’s functions. At present, the 3D printing swarm consists of the printers, a transporter which can take them between job sites, and the floor tiles which provide power and support the build surfaces. To add to this ecosystem, this project is focused on the design …

Combined Stressors In Reliability Failure Modes In Flip-Chip Electronic Packaging, Mahsa Montazeri

Graduate Theses and Dissertations

The trend toward miniaturization of electronic devices to fulfill Moore’s law introduces new reliability concerns to the electronic packaging process while worsening existing primary challenges. In solder interconnect specifically, temperature cycling is one of the prominent failure threats. However, with further downscaling of the flip-chip solder connections, electromigration also present a precarious failure mode in these interconnects. On the other hand, understanding the degradation mechanism in solders is crucial for the power electronic products' reliability considering the industrial tendency to replace wirebonds with solder attachment while improving the current carry capacity. This dissertation utilizes FEA simulation and an experimental approach …

Mission Profile Effects On Automotive Drivetrain Electronics Reliability: Modeling And Mitigation, Bakhtiyar Mohammad Nafis

Graduate Theses and Dissertations

The reliability of electronic devices is dependent upon the conditions to which they are subject. Temperature variations coupled with differences in thermal expansion between bonded materials results in thermomechanical stresses to build up, which can instigate failure in the interconnects or other critical regions. With the move towards electrification in the automotive industry, there is the increasingly important consideration of powertrain electronics reliability, the pertinent conditions being governed by the drive cycle or mission profile of the vehicle. The mission profile determines the power dissipated by the electronic devices, which determines the peak and mean temperature, temperature swing and the …

Development Of Novel Battery Materials For Lithium-Ion Batteries And Beyond, Jiyu Cai

Graduate Theses and Dissertations

As fossil fuels are depleting and causing environmental issues, it becomes imperative to widely implement renewable energies (e.g., solar and wind power). In this context, electrical energy storage (EES) systems are essential to accommodate the intermittent supply and uneven distribution of renewable energies. To this end, high-energy-density EES devices are highly demanded, such as rechargeable batteries. This dissertation presents my efforts in developing novel battery materials for lithium-ion batteries (LIBs), sodium-ion batteries (SIBs), and solidstate lithium batteries (SSLBs). These efforts include electrochemical evaluations of battery materials, surface modifications of electrodes via atomic layer deposition (ALD), and advanced characterizations of batteries …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Influence Of Extracellular Matrix Stiffness And Topography On Neuronal Cell Behavior And Neurite Outgrowth, Mohan Yasodharababu

Graduate Theses and Dissertations

The focus of regeneration therapy for traumatic brain injuries and Alzheimer's disease is on the promotion and growth of neuronal cells. In vitro research attempts to improve this by modifying the stiffness and topography of the extracellular matrix (ECM). However, the limitations of in vitro experiments make it difficult to control the individual factors influencing neuronal cell growth. A computational model can be used to decouple individual factors and study them individually to gain a better understanding of the mechanics between the neuronal cell and ECM, which will aid in the design of in vitro experimental studies.

This study develops …

An Investigation Of Testing Parameters On The Frictional Properties Of Patterned Core-Shell Nanostructures, Colin Phelan

Graduate Theses and Dissertations

Friction tests are a beneficial means to analyze the tribological characteristics and advantages of materials and textured surfaces. However, the selected test parameters can significantly influence the results. This work explores the significance of the friction testing parameters on the frictional performances of core-shell nanostructure-textured surfaces (CSNTSs). Several applied normal loads (10 μN, 100 μN, and 500 μN) and diamond counterface indenter tip radii (1 μm, 5 μm, and 20 μm) were selected for the testing of Al/diamond-like-carbon (DLC) and Al/amorphous silicon (a-Si) CSNTSs. The measured friction values of the CSNTSs were then compared to a matching Al/DLC film and …

Mathematical Modeling Of A Two Wheeled Robotic Base, Kathryn Remell

Mechanical Engineering Undergraduate Honors Theses

This thesis presents the concept of using a two wheeled robot on the moon and briefly explores the requirements for successful long term operation in a lunar environment. The mathematical model for the motion of a robot with two fixed wheels on a differential drive with in a global reference frame. The robot is assumed to be balancing a platform so the mathematical model to balance the platform with wheel motors is also developed and briefly evaluated.

Numerical Simulations Of Directed Self-Assembly Methods In Di-Block Copolymer Films For Efficient Manufacturing Of Nanoscale Patterns With Long-Range Order, Joseph Hill

Graduate Theses and Dissertations

Directed self-assembly (DSA) of block copolymers (BCPs) has been shown as a viable method to achieve bulk fabrication of surface patterns with feature sizes smaller than those available through traditional photolithography. Under appropriate thermodynamic conditions, BCPs will self-assemble into ordered micro-domain morphologies, a desirable feature for many applications. One of the primary interests in this field of research is the application of thin-film BCPs to existing photolithography techniques. This “bottom-up” approach utilizes the self-assembled BCP nanostructures as a sacrificial templating layer in the lithographic process.

While self-assembly occurs spontaneously, extending orientational uniformity over centimeter-length scales remains a critical challenge. A …

Mechanical And Frictional Behavior Of Textured And Non-Textured Surfaces, Raghuram R. Santhapuram

Graduate Theses and Dissertations

Tribology is the study of surfaces where two objects are sliding against another. Significant energy is lost due to friction between the sliding surfaces. Therefore, developing or designing surfaces to minimize friction is critical for the durability and reliability of the mechanical components. Several researchers have identified that surface texturing at the nanoscale (nanotexture) would reduce the friction between the contacting surfaces. The nanotextured surfaces have several applications in microelectromechanical systems and nanoelectromechanical systems. This dissertation employs molecular dynamics simulations to investigate the frictional and mechanical response of nanotextured aluminum (Al) and Al/amorphous silicon (a-Si) composite surfaces.

This study determines …

Adhesion And Deformation Mechanisms Of Polydopamine And Polytetrafluoroethylene: A Multiscale Computational Study, Matthew Brownell

Graduate Theses and Dissertations

Polydopamine (PDA) has been shown to bond via covalent bonding, van der Waals forces, and hydrogen bonding and is known to adhere strongly to almost any material. The application of PDA between a substrate and a PTFE surface coating has resulted in low friction and a greatly reduced wear rate. Previous research probing the capabilities and limitations of PDA/PTFE films have studied the wear and mechanical properties of the film, but the overall adhesive and deformation mechanisms remain unclear.

In this research, we investigate the tribological properties of PDA and PTFE molecules and composites from the atomic to the microscale …

Design, Fabrication, And Reliability Effects Of Additively Manufactured First Level Compliant Interconnects For Microelectronics Application, Tumininu David Olatunji

Graduate Theses and Dissertations

Semiconductor packaging and development is greatly dependent on the magnitude of interconnect and on-chip stress that ultimately limits the reliability of electronic components. Thermomechanical related strains occur because of the coefficient of thermal expansion mismatch from different conjoined materials being assembled to manufacture a device. To curb the effect of thermal expansion mismatch between conjoined parts, studies have been done in integrating compliant structures between dies, solder balls, and substrates. Initial studies have enabled the design and manufacturing of these structures using a photolithography approach which involves a high number of fabrication steps depending on the complexity of the structures …

The Varied Thermal Response Of Magnetic Iron-Oxide Nanoparticles During Induction Heating In Liquid And Solid-Liquid Phase Change Mediums, Joshua Tompkins

Graduate Theses and Dissertations

This study investigates the induction heating response of uncapped iron oxide nanoparticles sonically dispersed as a nanofluid and mechanically distributed in solid phase change materials. The nanoparticles examined have a mean diameter of 14.42 nm and are magnetically heated in an alternating magnetic field at an amplitude of 72.6 kA/m at frequencies of 217, 303, and 397 kHz. Nanoparticle characterization was undertaken through transition electron microscopy, x-ray diffraction, and dynamic light scattering when in suspension. Carrier fluids were characterized through viscosity, heat capacity, and density measurements which were used in the calorimetric calculation of the specific absorption rate (SAR) of …

Microextrusion 3d Printing Of Optical Waveguides And Microheaters, Edidiong Nseowo Udofia

Graduate Theses and Dissertations

The drive for smaller and more compact devices presents several challenges in materials and fabrication strategies. Although photolithography is a well-developed method for creating microdevices, the disparate requirements in fabrication strategies, material choices, equipment and process complexities have limited its applications. Microextrusion printing (μEP) provides a promising alternative for microfabrication. Compared to the traditional techniques, the attractions lie in the wide range of printable material choice, greater design freedom, fewer processing steps, lower cost for customized production, and the plurality of compatible substrates. However, while extrusion-based 3D printing processes have been successfully applied at the macroscale, this seeming simplicity belies …

Predicting The Mechanical Properties Of Nanocomposites Reinforced With 1-D, 2-D And 3-D Nanomaterials, Scott Edward Muller

Graduate Theses and Dissertations

Materials with features at the nanoscale can provide unique mechanical properties and increased functionality when included as part of a nanocomposite. This dissertation utilizes computational methods at multiple scales, including molecular dynamics (MD) and density functional theory (DFT), and the coupled atomistic and discrete dislocation multiscale method (CADD), to predict the mechanical properties of nanocomposites possessing nanomaterials that are either 1-D (carbyne chains), 2-D (graphene sheets), or 3-D (Al/amorphous-Si core-shell nanorod).

The MD method is used to model Ni-graphene nanocomposites. The strength of a Ni-graphene nanocomposite is found to improve by increasing the gap between the graphene sheet and a …

Motor Control Systems Analysis, Design, And Optimization Strategies For A Lightweight Excavation Robot, Austin Jerold Crawford

Graduate Theses and Dissertations

This thesis entails motor control system analysis, design, and optimization for the University of Arkansas NASA Robotic Mining Competition robot. The open-loop system is to be modeled and simulated in order to achieve a desired rapid, yet smooth response to a change in input. The initial goal of this work is to find a repeatable, generalized step-by-step process that can be used to tune the gains of a PID controller for multiple different operating points. Then, sensors are to be modeled onto the robot within a feedback loop to develop an error signal and to make the control system self-corrective …

Silicone Tadpole: Research Into Soft Bodies, Danielle Fernandez

Mechanical Engineering Undergraduate Honors Theses

In this thesis, research is conducted in the area of soft robotics by building a soft tadpole that can deform with a specific air pressure. The goal is to mimic the motion of an organic tadpole in respect to its S-shaped tail movement. The angle of deformation, derived from material mechanic theories, ranges from 45 to 80 degrees for this type of movement. The design includes a head compartment which acts as a tank to transfer nitrogen pressure and a tail section that receives the said pressure and bends as a result. The tail section was designed with two rows …

The Effect Of Incorporating End-User Customization Into Additive Manufacturing Designs, Jonathan D. Ashley

Graduate Theses and Dissertations

In the realm of additive manufacturing there is an increasing trend among makers to create designs that allow for end-users to alter them prior to printing an artifact. Online design repositories have tools that facilitate the creation of such artifacts. There are currently no rules for how to create a good customizable design or a way to measure the degree of customization within a design. This work defines three types of customizations found in additive manufacturing and presents three metrics to measure the degree of customization within designs based on the three types of customization. The goal of this work …

Microheater Array Powder Sintering (Maps) For Printing Flexible Electronics, Nicholas Holt

Graduate Theses and Dissertations

Microheater array powder sintering (MAPS) is a novel additive manufacturing process that uses an array of microheaters to selectively sinter powder particles. MAPS shows great promise as a new method of printing flexible electronics by enabling digital curing of conductive inks on a variety of substrates. MAPS operation relies on establishing a precision air gap of a few microns between an array of microheaters, which can reach temperatures of 600°C, and a layer of conductive ink which can be deposited onto a flexible substrate. This system presents challenges, being: the fabrication of a microheater that can reach suitable temperatures in …

Phase Transitions In Monochalcogenide Monolayers, Mehrshad Mehboudi

Graduate Theses and Dissertations

Since discovery of graphene in 2004 as a truly one-atom-thick material with extraordinary mechanical and electronic properties, researchers successfully predicted and synthesized many other two-dimensional materials such as transition metal dichalcogenides (TMDCs) and monochalcogenide monolayers (MMs). Graphene has a non-degenerate structural ground state that is key to its stability at room temperature. However, group IV monochalcogenides such as monolayers of SnSe, and GeSe have a fourfold degenerate ground state. This degeneracy in ground state can lead to structural instability, disorder, and phase transition in finite temperature. The energy that is required to overcome from one degenerate ground state to another …

A Nanoindentation Study Of The Fatigue Properties Of Al/A-Si Core-Shell Nanostructures, Jason Steck

Mechanical Engineering Undergraduate Honors Theses

Nanostructure-textured surfaces can reduce friction and increase the reliability of micro- and nanoelectromechanical systems (NEMS/MEMS). For MEMS incorporating moving parts, the fatigue properties of nanostructures pose a challenge to their reliability in long-term applications. In this study, the fatigue behavior of hemispherical Al/a-Si core-shell nanostructures (CSNs), bare hemispherical Al nanodots, and a flat Al/a-Si layered thin film have been studied using nanoindentation and nano-scale dynamic mechanical analysis (nano-DMA) techniques. Fatigue testing with nano-DMA shows that the deformation resistance of CSNs persists through 5.0 × 10⁴ loading cycles at estimated contact pressures greater than 15 GPa. When the a-Si shell …

Particle Image Velocimetry Design & Installation, Zach Ritchie

Mechanical Engineering Undergraduate Honors Theses

This work will mainly focus on the design, construction, and installation of the Particle Image Velocimetry (PIV) system in the Chemical Hazards Research Center wind tunnel. The PIV system utilizes a Class IV (double pulsed) laser, optics to produce a light sheet, timing circuitry, and a high-resolution camera (with buffered output) to measure a system’s velocity (two-dimensional) field by determining the displacement of particles over the time between laser pulses. For maximum mobility and functionality, the PIV system was installed in the center of the tunnel on a moveable cart with the laser and camera mounted to an adjustable support. …

Investigation Of A Numerical Algorithm For A Discretized Rubber-Belt Continuously Variable Transmission Dynamic Model And Techniques For The Measurement Of Belt Material Properties., Brian Gene Ballew

Graduate Theses and Dissertations

A numerical algorithm for modeling the dynamic response of a rubber-belt Continuously Variable Transmission (CVT) belt is recreated. The numerical attributes applied to the algorithm and difficulties with numerical stability are discussed in detail. The degrees of freedom of the system have been expanded to include the dynamics of the engine torque output and vehicle loads such as rolling resistance and aerodynamic drag. This was done to emphasize the use of the model as an analysis tool for simulating CVT/engine/vehicle response. The increased degrees of freedom require the addition of a linear dampening element between belt nodes to dampen resonance …

Traction-Separation Relationships For Hydrogen-Induced Grain Boundary Embrittlement In Nickel Via Molecular Dynamics Simulations, Wesley Allen Barrows

Graduate Theses and Dissertations

The deleterious effects of atomic and molecular hydrogen on the mechanical properties of metals have long been observed. Although several theories exist describing the mechanisms by which hydrogen negatively influences the failure of materials, a consensus has yet to be reached regarding the exact mechanism or combination of mechanisms. Two mechanisms have gained support in explaining hydrogen’s degradative role in non-hydride forming metals: hydrogen-enhanced localized plasticity and hydrogen-enhanced decohesion. Yet, the interplay between these mechanisms and microstructure in metallic materials has not been explained. Accordingly, for this thesis, the three main objectives are: (i) to develop a numerical methodology to …

Utilizing Failure Information For Mission Assessment And Optimization For Complex Systems, Charlie Destefano

Graduate Theses and Dissertations

This paper presents a new failure analysis method, Failure Identification for Mission Analysis (FIMA), which performs a general failure analysis for the overall state of a system, as well as a mission-specific analysis that identifies how failures may have differing effects on the various mission tasks that a system must complete. The FIMA method is capable of being implemented at any point in the design process. During early design stages, the FIMA method will identify various qualitative failure scenarios based on programmed functional relationships and any number of initial failures wished to be simulated. The functional relationships for this method …

Highly Transparent, Self-Cleaning, And Antireflective Nanoparticle Coatings, Corey Seth Thompson

Graduate Theses and Dissertations

Current solar panel technologies require a sheet of glass to serve as both mechanical support and to protect the cells from the environment. The reflection from the glass sheet can reflect up to 8% of the incident light, reducing the power output of the panel. Antireflective coatings can be used to allow more light to enter the panel to be converted into usable electricity. However, no solid thin film materials exhibit a low enough index of refraction to serve as antireflective coatings for common solar glass. The main goal of this research was to investigate the self-cleaning, antifogging, and antireflective …

Atomistic Simulation And Virtual Diffraction Characterization Of Alumina Interfaces: Evaluating Structure And Stability For Predictive Physical Vapor Deposition Models, Shawn Patrick Coleman

Graduate Theses and Dissertations

The objectives of this work are to investigate the structure and energetic stability of different alumina (Al₂O₃) phases using atomistic simulation and virtual diffraction characterization. To meet these objectives, this research performs molecular statics and molecular dynamics simulations employing the reactive force-field (ReaxFF) potential to model bulk, interface, and surface structures in the θ-, γ-, κ-, and α-Al₂O₃ system. Simulations throughout this study are characterized using a new virtual diffraction algorithm, developed and implemented for this work, that creates both selected area electron diffraction (SAED) and x-ray diffraction (XRD) line profiles without assuming …

Electroencephalography(Eeg) Data Collection And Processing Through Machine Learning, Jayshree Desai

Graduate Theses and Dissertations

Machine learning methods are an excellent way for understanding the neural basis of human decision making. Some machine learning systems try to eradicate the need for human intuition in data analysis whereas others embrace a collective approach between humans and machines. The objective of this project is to collect Electroencephalography (EEG) signals through wireless sensors, and the process the collected signals through machine learning methods. The EEG data is collected using three EEG electrodes, each being the positive, negative and ground terminals respectively. Since the signal measures in the unit of micro-volts it needs to be amplified using amplifier circuit. …