Open Access. Powered by Scholars. Published by Universities.®

VLSI and Circuits, Embedded and Hardware Systems Commons™

Open Access. Powered by Scholars. Published by Universities.®

Electronic Devices and Semiconductor Manufacturing

Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 91 - 97 of 97

Full-Text Articles in VLSI and Circuits, Embedded and Hardware Systems

Vlsi Implementation Of High Speed And High Resolution Fft Algorithm Based On Radix 2 For Dsp Application, Nooshin Mahdavi, Rozita Teymourzadeh, Masuri Othman Dec 2006

Vlsi Implementation Of High Speed And High Resolution Fft Algorithm Based On Radix 2 For Dsp Application, Nooshin Mahdavi, Rozita Teymourzadeh, Masuri Othman

Dr. Rozita Teymourzadeh, CEng.

Using Fast Fourier Transform (FFT) is indispensable in most signal processing applications. Designing an appropriate algorithm for the implementation of FFT can be efficacious in digital signal processing. Sophisticated techniques such as pipelining and parallel calculations have potential impacts on VLSI implementation of FFT algorithm. Furthermore, a mathematic approach such as floating point calculation achieves higher precision. In this paper, an efficient algorithm with using parallel and pipelining methods is proposed to implement high speed and high resolution FFT algorithm. Latency reduction is an important issue to implement the high speed FFT on FPGA. The Proposed FFT algorithm shows the …

Go to article

An Enhancement Of Decimation Process Using Fast Cascaded Integrator Comb (Cic), Rozita Teymourzadeh, Masuri Othman Dec 2005

An Enhancement Of Decimation Process Using Fast Cascaded Integrator Comb (Cic), Rozita Teymourzadeh, Masuri Othman

Dr. Rozita Teymourzadeh, CEng.

The over sampling technique has been shown to increase the SNR and is used in many high performance system such as in the ADC for audio and DAT systems. This paper presents the design of the decimation and its VLSI implementation which is the sub-component in the over sampling technique. The design of three main units in the decimation stage that is the Cascaded Integrator Comb (CIC) filter, the associated half band filters and the droop correction are also described. The Verilog HDL code in Xilinx ISE environment has been derived to describe the CIC filter properties and downloaded in …

Go to article

An Overview Of The Decimation Process And Its Vlsi Implementation, Rozita Teymourzadeh, Masuri Othman Dec 2005

An Overview Of The Decimation Process And Its Vlsi Implementation, Rozita Teymourzadeh, Masuri Othman

Dr. Rozita Teymourzadeh, CEng.

Digital Decimation process plays an important task in communication system. It mostly is applied in transceiver when the frequency reduction is required. However, the decimation process for sigma delta modulator is considered in this research work. The proposed design was simulated using MATLAB software and implemented by hardware description language in Xilinx environment. Furthermore, the proposed advance arithmetic unit is applied to improve the system efficiency.

Go to article

An Improved Recursive And Non-Recursive Comb Filter For Dsp Applications, Rozita Teymourzadeh, Masuri Othman Dec 2005

An Improved Recursive And Non-Recursive Comb Filter For Dsp Applications, Rozita Teymourzadeh, Masuri Othman

Dr. Rozita Teymourzadeh, CEng.

The recursive and non-recursive comb filters are commonly used as decimators for the sigma delta modulators. This paper presents the analysis and design of low power and high speed comb filters. The comparison is made between the recursive and the non-recursive comb filters with the focus on high speed and saving power consumption. Design procedures and examples are given by using Matlab and Verilog HDL for both recursive and non-recursive comb filter with emphasis on frequency response, transfer function and register width. The implementation results show that non-recursive comb filter has capability of speeding up the circuit and reducing power …

Go to article

Vlsi Implementation Of Cascaded Integrator Comb Filters For Dsp Applications, Rozita Teymourzadeh, Masuri Othman Dec 2005

Vlsi Implementation Of Cascaded Integrator Comb Filters For Dsp Applications, Rozita Teymourzadeh, Masuri Othman

Dr. Rozita Teymourzadeh, CEng.

The recursive comb filters or Cascaded Integrator Comb filter (CIC) are commonly used as decimators for the sigma delta modulators. This paper presents the VLSI implementation, analysis and design of high speed CIC filters which are based on a low-pass filter. These filters are used in the signal decimation which has the effect on reducing the sampling rate. It is also chosen because its attractive property of both low power and low complexity since it dose not required a multiplier. Simulink toolbox available in Matlab software which is used to simulator and Verilog HDL coding help to verify the functionality …

Go to article

On-Chip Implementation Of Cascaded Integrated Comb Filters (Cic) For Dsp Application, Rozita Teymourzadeh, Masuri Othman Dec 2004

On-Chip Implementation Of Cascaded Integrated Comb Filters (Cic) For Dsp Application, Rozita Teymourzadeh, Masuri Othman

Dr. Rozita Teymourzadeh, CEng.

This paper presents the design of a CIC filters based on a low-pass filter for reducing the sampling rate, also known as decimation process. The targeted application for the filter is in the analog to digital conversion (ADC).The CIC is chosen because of its attractive property of both low power and complexity since it dose not required multipliers. Simulink toolbox available in Matlab software is used to design and simulate the functionality of the CIC filter. This paper also shows how sample frequency is decreased by CIC filter and it can be used to give enough stop-band attenuation to prevent …

Go to article

Design For Signal Integrity In High Frequency, High Density Circuit Boards, Juan Manuel Talavera Martinez Jan 2003

Design For Signal Integrity In High Frequency, High Density Circuit Boards, Juan Manuel Talavera Martinez

Theses

The electronics market is continually seeking fast and small high performance products. The clock frequency in computer systems is often above 2GHz and new generations of laptops have considerably reduced in size. These features make printed circuit board (PCB) design more difficult than in the past.

This thesis is an investigation of the current design of high speed PCB. The complexity of this type of circuit makes the designer needs an extensive knowledge of the techniques used to generate a reliable signalling, in other words, signal integrity. To achieve this objective, the design community has to overcome several problem related …

Go to article

First Prev