VLSI and Circuits, Embedded and Hardware Systems Commons^™

Design And Analysis Of A Discrete, Pcb-Level Low-Power, Microwave Cross-Coupled Differential Lc Voltage-Controlled Oscillator, Pavin Singh Virdee

Master's Theses

Radio Frequency (RF) and Microwave devices are typically implemented in Integrated Circuit (IC) form to minimize parasitics, increase precision and tolerances, and minimize size. Although IC fabrication for students and independent engineers is cost-prohibitive, an abundance of low-cost, easily accessible printed circuit board (PCB) and electronic component manufacturers allows affordable PCB fabrication.

While nearly all microwave voltage-controlled oscillator (VCO) designs are IC-based, this study presents a discrete PCB-level cross-coupled, differential LC VCO to demonstrate this more affordable and accessible approach. This thesis presents a 65 mW, discrete component VCO PCB with industry-comparable RF performance. A phase noise of -103.7 dBc/Hz …

Design And Characterization Of Standard Cell Library Using Finfets, Phanindra Datta Sadhu

Master's Theses

The processors and digital circuits designed today contain billions of transistors on a small piece of silicon. As devices are becoming smaller, slimmer, faster, and more efficient, the transistors also have to keep up with the demands and needs of the daily user. Unfortunately, the CMOS technology has reached its limit and cannot be used to scale down due to the transistor's breakdown caused by short channel effects. An alternative solution to this is the FinFET transistor technology, where the gate of the transistor is a three dimensional fin that surrounds the transistor and prevents the breakdown caused by scaling …

Design Of An Ultra-Wideband Frequency-Modulated Continuous Wave Short Range Radar System For Extending Independent Living, Toai-Chi Nguyen

Master's Theses

Falls in the disabled and elderly people have been a cause of concern as they can be immobilized by the fall and have no way to contact others and seek assistance. The proposed frequency modulated continuous wave (FMCW) short range radar (SRR) system, which uses ultra-wideband (UWB) signals can provide immediate assistance by monitoring and detecting fall events. The unique characteristics of this system allow for a frequency-based modulation system to carry out triangulation and sense the location of the fall through the usage of a continuous chirp signal that linearly sweeps frequency. This project focuses on the development, design …

Experimental Study And Modeling Of The Gm-I Dependence Of Long-Channel Mosfets, Michael Fong Cheng

Master's Theses

This thesis describes an experimental study and modeling of the current-transconductance dependence of the ALD1106, ALD1107, and CD4007 arrays. The study tests the hypothesis that the I-gm dependence of these 7.8 µm to 10 µm MOSFETs conforms to the Advanced Compact Model (ACM). Results from performed measurements, however, do not support this expectation. Despite the relatively large length, both ALD1106 and ALD1107 show sufficiently pronounced ‘short-channel’ effects to render the ACM inadequate. As a byproduct of this effort, we confirmed the modified ACM equation. With an m factor of approximately 0.6, it captures the I-gm dependence with sub-28% maximum error …

Phase Locked Loop Integrated Circuit, Scott Buchanan, Jonathan Bonello

Electrical Engineering

No abstract provided.

Chipper: Capacitive Bed Occupancy Sensing For An Intelligent Alarm Clock, David Levi

Electrical Engineering

What if your alarm clock knew when you got out—and stayed out—of bed? Current alarm clocks happily let you go back to bed after turning them off. In this project, I build an alarm which only stops ringing when you get out bed, and starts ringing again if you lie back in bed.

This project uses capacitance to detect bed occupancy. A person on or near the bed creates a tiny, picofarads level increase in capacitance, as seen by a sensor placed under the mattress. A microprocessor interprets this signal, and also drives an audio alarm. Shielding of the sensor …

Design And Fabrication Techniques Of Devices For Embedded Power Active Contact Lens, Errol Heradio Leon

Master's Theses

This thesis designed and fabricated various devices that were interfaced to an IC for an active contact lens that notifies the user of an event by detection of an external wireless signal. The contact lens consisted of an embedded antenna providing communication with a 2.4GHz system, as well as inductive charging at an operating frequency of 13.56 MHz. The lens utilized a CBC005 5µAh thin film battery by Cymbet and a manufactured graphene super capacitor as a power source. The custom integrated circuit (IC) was designed using the On Semiconductor CMOS C5 0.6 µm process to manage …

Low Voltage Cmos Sar Adc Design, Ryan Hunt

Electrical Engineering

This project centers on the design of a single ended 10-bit successive approximation register analog to digital converter (SAR ADC for short) that easily interfaces to a micro-controller, such as an Arduino. With micro-controller interfacing in mind, the universal data transfer technique of SPI proved an easy way to communicate between the ADC and the micro-controller. The ADC has a range of 1V (highest code value) to 0V (lowest code value) and operates from a single voltage rail value of 1.8V. Typical SPI clock speeds run on the order of 2MHz and with a 10-bit ADC this means a sampling …

Mos Current Mode Logic (Mcml) Analysis For Quiet Digital Circuitry And Creation Of A Standard Cell Library For Reducing The Development Time Of Mixed Signal Chips, David Marusiak

Master's Theses

Many modern digital systems use forms of CMOS logical implementation due to the straight forward design nature of CMOS logic and minimal device area since CMOS uses fewer transistors than other logic families. To achieve high-performance requirements in mixed-signal chip development and quiet, noiseless circuitry, this thesis provides an alternative toCMOSin the form of MOS Current Mode Logic (MCML). MCML dissipates constant current and does not produce noise during value changing in a circuit CMOS circuits do. CMOS logical networks switch during clock ticks and with every device switching, noise is created on the supply and ground to deal with …

Full Custom Vlsi Design Of On-Line Stability Checkers, Chris Y. Lee

Master's Theses

A stability checker is a clocked storage element, much like a flip-flop, which detects unstable and late signals in the pipeline of a digital system. The On-line stability checker operates concurrently with its associated circuit-under-test (CUT). This thesis describes the full custom very-large-scale integration (VLSI) design and testing process of On-Line Stability Checkers. The goals of this thesis are to construct and test Stability Checker designs, and to create a design template for future class projects in the EE 431 Computer-Aided Design (CAD) of VLSI Devices course at Cal Poly.

A method for concurrent fault testing called On-line Stability Checking …

Project 308: Augmented Reality Mario Kart, Joseph Abad, David Allender, Joryl Calizo, Ryan Gaspar, Gavin Lee

Computer Engineering

Mario Kart is a popular go-kart racing game developed by Nintendo. The premise of the game is simple: drive a go-kart along a racetrack and reach the finish line before the other players. What makes this game unique, however, is the inclusion of weapons, traps, and other projectiles that a player can use to gain an advantage in the race. We have taken on the challenge of not only recreating this amazing game, but using the art of Augmented Reality to fully immerse the player in the full experience. Rather than play the game on a television screen with a …

Laser Cursor, Michael Liman

Electrical Engineering

A user controls a cursor on a computer screen using a laser pointer. A camera picks up the laser pointer’s position and sends the data to the computer to move the cursor in the correct position.