Civil and Environmental Engineering Commons^™

2021 Final Butte Reduction Works (Brw) Phase I Quality Assurance Project Plan (Qapp) Revision 3. February 2021, Pioneer Technical Services, Inc.

Silver Bow Creek/Butte Area Superfund Site

No abstract provided.

Quantifying Materials Waste In The Egyptian Construction Industry: A Critical Analysis Of Rates And Factors, Ayman Ahmed Ezzat Othman, Ahmed Osama Daoud Dr., Obas John Ebohon, Ali Bayyati

Architectural Engineering

Construction and demolition waste (CDW) is a critical challenge facing the construction industry. It leads to deterioration of the triple bottom line of sustainability. Unfortunately, the CDW management research in Egypt lacks studies investigating (1) the variations in CDW generation (CDWG) among different types of construction projects, and (2) the factors affecting CDW reduction (CDWR). Based on a benchmarking approach, this research (1) quantifies CDW in terms of generation rates and costs among different construction project types in Egypt, and (2) investigates the relationship between CDWG and different adopted CDWR factors. Using structured interviews, a comparative case study was conducted …

Structural Identification And Damage Detection In Bridges Using Wave Method And Uniform Shear Beam Models: A Feasibility Study, Mehran Rahmani, Manan Naik

Mineta Transportation Institute

This report presents a wave method to be used for the structural identification and damage detection of structural components in bridges, e.g., bridge piers. This method has proven to be promising when applied to real structures and large amplitude responses in buildings (e.g., mid-rise and high-rise buildings). This study is the first application of the method to damaged bridge structures. The bridge identification was performed using wave propagation in a simple uniform shear beam model. The method identifies a wave velocity for the structure by fitting an equivalent uniform shear beam model to the impulse response functions of the recorded …

Modeling The Effectiveness Of Cooling Trenches For Stormwater Temperature Mitigation, Scott A. Wells

Civil and Environmental Engineering Faculty Publications and Presentations

Due to elevated runoff stormwater temperatures from impervious areas, one management strategy to reduce stormwater temperature is the use of underground flow through rock media termed a cooling trench. This paper examines the governing equations for the liquid phase and media phases for modeling the temperature leaving a cooling trench assuming that changes in temperature occurred longitudinally through the cooling trench. This model is dependent on parameters such as the media type, porosity, media initial temperature, inflow rate, and inflow temperature. Several approaches were explored mathematically for evaluating the change in temperature of the water and the cooling trench media. …

Multi-Skilled Labor Optimization With Partial Allocation Of Resources, Amira Saleh

Theses and Dissertations

The current practice of labor allocation in construction schedules assumes single-skilled workforce; meaning that each worker is assumed to be skilled in only one trade. In such practice, at any instance in the project lifecycle, some of the workforce become idle waiting for other labor types to complete their work. Traditionally, companies may relocate idle workers to other projects and return them back to their original project when needed again. This complicates the resource management process and is not often performed successfully, leading to schedule and cost overruns. Alternatively, project managers may keep the idle workforce at their projects because …

Predicting The Effect Of Fly Ash On Concrete’S Mechanical Properties By Ann, Mohammad Mehdi Roshani, Seyed Hamidreza Kargar, Visar Farhangi, Moses Karakouzian

Civil and Environmental Engineering and Construction Faculty Research

© 2021 by the authors. Licensee MDPI, Basel, Switzerland. Fly ash, as a supplemental pozzolanic material, reduces concrete’s adverse environmental footprint by decreasing the emission of carbon dioxide (CO2 ) during the cement manufacturing process. Fly ash, which is a waste material, can enhance both the mechanical characteristics and durability of concrete, and has the capability to play an important role in sustainable design. Considering the widespread interest in applying Fly ash, and despite research studies, the level of replacement is still unclear. In this paper, a novel method using artificial neural networks (ANN) is presented to predict concrete’s mechanical …

A Web-Based Change Control Management Toolkit For Lump-Sum Turnkey Contractors: Transformation To Third Generation, Ahmed Omran

Theses and Dissertations

Project deviations and changes are one of the key common particulars encountered in the Construction industry. Project changes can occur in different forms, may impact different pillars of the project, and can be caused due to the existence of various underlying factors. Mismanaging or lack of controlling these changes is one of the key contributing factors leading to project hardships. Contractors incur profit erosion, scope creep, and time slippages mainly by failing to have an effective project change management system enforced within its project execution philosophy. Such adversity is amplified for contractors engaging in lump-sum turnkey “LSTK” projects. Contractors encounter …

The Use Of Dynamic Message Signs (Dmss) On The Freeways: An Empirical Analysis Of Dmss Logs And Survey Data, Boniphace Kutela, Hualiang Teng

Civil and Environmental Engineering and Construction Faculty Research

This study evaluates the Dynamic Message Signs (DMSs) use to dissipate incident information on the freeways in Las Vegas, Nevada. It focuses on the DMSs message timing, extent, and content, from the operators’ and drivers’ perspectives, considering the variability in drivers’ freeway experience. Two-week incidents data with fifty-nine incidents, DMS log data, and responses from a survey questionnaire were used. The descriptive analysis of the incidents revealed that about 54% of the incidents had their information posted on the DMSs; however, information of only 18.6% of the incidents was posted on time. The posted information covered the incident type (54.2%), …

Truck Platooning Effects On Girder Bridges, Joshua Steelman, Jay A. Puckett, Daniel Linzell, Bowen Yang

Nebraska Department of Transportation: Research Reports

Truck platooning – digitally linking two or more trucks to travel in a closely spaced convoy – is increasingly used to save fuel, and reduce driver work and road congestion. Currently, the platoon load effects with several constant headways on bridges have been evaluated and compared to AASHTO design and legal loads. However, reliability assessment and a more rigorous investigation of headway spacing assumptions for truck platoons are lacking. This research provides a framework for determining how much a platoon permit load might be increased given strict control over the load characteristics and operational tactics. The present research evaluates the …

Covid-19: A Spectio-Temporal Analysis Of Air Quality Status In Coking Coalfields Of India Due To Nationwide Lockdown In India, Amarjeet Singh Mr., Gurdeep Singh Dr.

Journal of Sustainable Mining

A novel infectious corona virus disease (COVID-19) was identified in month of December 2019.It has now been announced as a worldwide pandemic by the World Health Organization [1]. The COVID-19 pandemic has positive impacts on the environmental pollutants. In present work, Coalfield areas of Jharia Coalfields (JCF), India have been taken as a case study to evaluate the effect of lockdown on air quality at 10 locations. This study had been selected to estimate the reduction in concentration of pollutants like PM₁₀, PM_2.5, SO₂, and NOx during 3 Seasons (summer, Post-Monsoon and winter season) …

New Particle Formation In The Remote Marine Boundary Layer, Guangjie Zheng, Yang Wang, For Full List Of Authors, See Publisher's Website.

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Marine low clouds play an important role in the climate system, and their properties are sensitive to cloud condensation nuclei concentrations. While new particle formation represents a major source of cloud condensation nuclei globally, the prevailing view is that new particle formation rarely occurs in remote marine boundary layer over open oceans. Here we present evidence of the regular and frequent occurrence of new particle formation in the upper part of remote marine boundary layer following cold front passages. The new particle formation is facilitated by a combination of efficient removal of existing particles by precipitation, cold air temperatures, vertical …

Course Master Planning, Haroon Stephen, Jee Woong Park

UNLV Best Teaching Practices Expo

Our specific teaching practice is to use a course master plan, which is a comprehensive document that provides the embodiment to the course skeleton often given in the syllabus. The master plan strategy addresses the need to provide multi-level perspectives of the course. The master plan provides a one-stop source of information and enables a consistent course delivery in case of multiple instructors assigned to a course in the same semester or on rotation.

Application Of Ultrasonic Measurements For The Evaluation Of Steel Fiber Reinforced Concrete, Belayhun Gebretsadik, Kazem Jdidirendi, Visar Farhangi, Moses Karakouzian

Civil and Environmental Engineering and Construction Faculty Research

This study investigates the feasibility of the application of ultrasonic measurement to characterize Steel-Fiber-Reinforced Concrete (SFRC). Specifically, the effects of steel fiber content, age, moisture content, and fiber orientation on Ultrasonic-Pulse-Velocity (UPV) were investigated. In this regard, beam and cylindrical samples were fabricated with different steel fiber contents. The result indicated that for beam specimens the UPV increases with the addition of fiber up to 2% and decreases for higher fiber percentages. Additionally, the fiber orientation within the beam specimens influences the UPV measurements. For cylindrical samples, the rate of UPV decreased with the addition of steel fiber reinforcement. In …

Quality Assessment Of Flexible Pavement Automated Cracking Data In Louisiana, Mostafiz Emtiaz

LSU Master's Theses

Pavement distress survey is the most critical and integral part of pavement management system. Transportation agencies all over the world depends on the accurate pavement distress survey to take major decisions like pavement rehabilitation or reconstruction. Pavement management at the network level requires accurate pavement distress survey to decide the allocation of budget for pavement maintenance, rehabilitation and reconstruction. This study started collected network-level cracking distress data through manual measurements on high-resolution pavement images and the results were used as the ground truth measurements to evaluate the corresponding automated distress data from the Pavement Management System database. Results showed that …

Generation Of 3d Model Of Downtown Sullivan, Jim Speer

2020 Fall Reports (Sullivan)

The City of Sullivan identified the downtown area as an area for improvement and needed a way to depict areas. In ENVI 610, one graduate student was able to address the agreed upon goals of developing a 3D model of the downtown square. Some recommendations for future use of the 3D model were made for land-use planning, drainage systems, elevation, and more.

Coating Compositions And Methods For Using The Same, Fateme Rezaei, Thomas P. Schuman, Glenn Morrison

Chemical and Biochemical Engineering Faculty Research & Creative Works

Coating compositions and methods for using the same are disclosed. The coating compositions can include an aminosilica adsorbent. The coating compositions can adsorb CO₂.

Strength, Fracture Evolution, And Permeability Changes From Confined Brazilian Tests On Sandstone, Tyler Louis Hagengruber

Civil Engineering ETDs

This research reports on confined Brazilian strength tests and concurrent permeability testing on sandstone. The majority of the tests measured permeability during loading to failure in the confined extension region. Additional testing includes unloading and reloading cycles to detect the development of microcracks and the dependence of permeability on mixed stress conditions. Further testing characterizes fracture networks by observing porosity changes due to microcrack interactions before peak load. All tests involve 5 cm diameter disk-shaped, jacketed samples that are subjected to confining stresses while they are diametrically loaded. Specially designed end caps allow for gas flow measurements. The test configuration …

Wearable Sensing Devices: Towards The Development Of A Personalized System For Construction Safety And Health Risk Mitigation, Chukwuma Nnaji, Ibukun Awolusi, Jeewoong Park, Alex Albert

Civil and Environmental Engineering and Construction Faculty Research

Wearable sensing devices (WSDs) are increasingly helping workers stay safe and healthy in several industries. However, workers, especially in the construction industry, have shown some aversion towards the use of WSDs due to their ability to capture specific information that may be considered personal and private. However, this revered information may provide some critical insight needed by management to plan and optimize worksite safety and support technology adoption in decision making. Therefore, there is a need to develop personalized WSD systems that are mutually beneficial to workers and management to ensure successful WSD integration. The present study aims to contribute …

Establish Integrated Crop-Livestock Production To Promote Ammonia Reduction In Livestock Industry, Hongnan Liu, Yulong Yin

Bulletin of Chinese Academy of Sciences (Chinese Version)

No abstract provided.

Accuracy Assessment Of Global Internal-Tide Models Using Satellite Altimetry, Loren Carrere, Brian K. Arbic, Brian Dushaw, Gary D. Egbert, Svetlana Erofeeva, Florent Lyard, Richard D. Ray, Clément Ubelmann, Edward Zaron, Zhongxiang Zhao, Jay F. Shriver, Maarten C. Buijsman, Nicolas Picot

Civil and Environmental Engineering Faculty Publications and Presentations

Altimeter measurements are corrected for several geophysical parameters in order to access ocean signals of interest, like mesoscale or sub-mesoscale variability. The ocean tide is one of the most critical corrections due to the amplitude of the tidal elevations and to the aliasing phenomena of high-frequency signals into the lower-frequency band, but the internal-tide signatures at the ocean surface are not yet corrected globally.

Internal tides can have a signature of several centimeters at the surface with wavelengths of about 50–250 km for the first mode and even smaller scales for higher-order modes. The goals of the upcoming Surface Water …

Development Of A Hurricane Recovery Function And Resilience Model For Single-Family Residential Homes, Uriel Robert Donald Clark

Theses and Dissertations

The resilience of communities, infrastructure, and the environment in the face of hurricanes has increasingly become of public interest in the wake of recent natural disasters and environmental activism. Previous methodologies have attempted to quantify resilience for various structures and scenarios. Many studies have primarily investigated the robustness of critical infrastructure (e.g., bridges, emergency facilities, and water systems) which are essential to the function of a community. However, few studies have applied this approach to individual residential buildings. Therefore, this research aimed to adapt the most recent recovery functions developed for residential homes by considering measurable factors that are known …

Using System Dynamics To Study The Effect Of Change Orders On Labor Productivity, Shrouk Gharib

Theses and Dissertations

Change orders in construction projects lead to numerous negative impacts, including loss of labor productivity, delays, and cost overruns. Owners and contractors are usually in disagreement when it comes to allocating the extent of responsibilities with respect to the resulting overruns. Each party tries to hold the other party fully responsible for such overruns through a series of claims and disputes. Several delay analysis techniques have been developed to aid in settling such disputes, however, they do not fully grasp the rippled impacts of change orders and do not assist parties in reaching consensus when it comes to finding the …

Exploring The Effect Of In-Plane Tensile Forces On The Two-Way Shear Strength: Review, Comparative Study And Future Works, Ahmed F. Deifalla, Eslam Mousa, Dina Yehia, Amr Abdelrahman

Future Engineering Journal

Two-way shear failure of slabs is a sudden one, which has catastrophic outcomes. Slabs with large spans may be subjected to in-plane tensile forces due to thermal or earthquake loading. There is a lack of agreement between various design codes regarding the significance of in-plane tensile forces on the two-way shear strength.

Two-way shear failure of slabs is a sudden one, which has catastrophic outcomes. Slabs with large dimensions may be subjected to in-plane tensile forces due to restraint or earthquake loading. There is a lack of agreement between various design codes regarding the significance of in-plane tensile forces on …

Effect Of Reinforcement Around Web Opening On The Cyclic Behavior Of Exterior Rc Beam-Column Joints, Ahmed F. Deifalla, Amin Saleh, Sherif Elwan, Mostafa Hamad, Sherif Elzeiny

Future Engineering Journal

In many situations, it is necessary to have a beam web opening in the plastic hinge location. However, very limited studies investigated the behavior of reinforced concrete (RC) beam-column joints with nearby beam web openings. A previous study was conducted for investigating the behavior of beam-column joints with unreinforced nearby web opening. In this study, the effect of adding additional reinforcing around a nearby web opening on the seismic behavior of RC exterior Beam-Column joints is being investigated. Nine full-scale beam-column joints were tested, four joints had an unreinforced opening, while five joints had reinforced opening. The behavior of the …

Optimum Cross Section And Longitudinal Profile For Unstiffened Fully Composite Steel Beams, Ahmed M. Ebid Dr.

Future Engineering Journal

Composite steel beam is commonly used element in multistory steel buildings today. The composite action between the concrete deck and the steel beam reduces both steel weight and deflection, accordingly, enhance floor economy and serviceability. Many earlier researches were carried out to optimize the design of the composite steel beams under both static loading and dynamic behavior. None of these researches was concerned in optimizing the cross section or the longitudinal profile of built-up composite steel beams. The aim of this research is to develop simple and practical equations to determine the optimum cross section dimensions and optimum longitudinal profile …

Mit-S1 Constitutive Model Calibration For A Portland-Area Soil, Steven Ryan Young

Dissertations and Theses

Soils that are intermediate to sands and clays are a challenge for geotechnical engineers since most methods for interpreting soil properties or soil behaviors are based on sands or clays and do not address behaviors of intermediate soils. This is a particular challenge for engineers in the Portland-area where many of the major soil units are composed of intermediate soils. Analysis of intermediate soils is further challenged since many standard constitutive models are based on sandy or clay-like soils. However, the MIT-S1 constitutive model is capable of capturing intermediate soil behavior. A calibration of the MIT-S1 constitutive model for Portland-area …

Management Of The Phosphorus-Cladophora Dynamic At A Site On Lake Ontario Using A Multi-Module Bioavailable P Model, Martin Auer, Cory P. Mcdonald, Anika Kuczynski, Chenfu Huang

Michigan Tech Publications, Part 1

The filamentous green alga Cladophora grows to nuisance proportions in Lake Ontario. Stimulated by high phosphorus concentrations, nuisance growth results in the degradation of beaches and clogging of industrial water intakes with attendant loss of beneficial uses. We develop a multi-module bioavailable phosphorus model to examine the efficacy of phosphorus management strategies in mitigating nuisance algal growth. The model platform includes modules simulating hydrodynamics (FVCOM), phosphorus-phytoplankton dynamics (GEM) and Cladophora growth (GLCMv3). The model is applied along a 25 km stretch of the Lake Ontario nearshore, extending east from Toronto, ON and receiving effluent from three wastewater treatment plants. Simulation …

Festigkeitsbeschreibung Des Schwerbetons Auf Alkalischlacken – Bindemittel, A Tulaganov, S Hodjaev, A Sultanov, B Tulaganov, B Otakulov, N Hodjaev, D Abdasov

The Scientific-Practice Journal of Architecture, Construction and Design

The article describes the laws of describing the strength of heavy concrete based on non-calcined alkaline binders. It is shown that strength is written as a function of the generalized argument.

Why Unsafety Has A Negative Relationship With Economic Effectiveness In The World?, Aziz Zikriyoev

The Scientific-Practice Journal of Architecture, Construction and Design

Due to regularly registered diseases and major accidents of workers in the construction industry can be explained expandable building projects and state programs for supporting population. The main purpose of the current paperwork is to explain wining unsafety at workplaces both theoretical and practical points of view generated with economic and social levels.

Implementation Of A Novel Inertial Mass System And Comparison To Existing Mass-Rig Systems For Shake Table Experiments, Alvaro Lopez, Peter Dusicka

Civil and Environmental Engineering Faculty Publications and Presentations

Shake table testing is one of the more effective experimental approaches used to study and evaluate seismic performance of structures. Reduced-scale models can still result in large-scale specimens where incorporating the required inertial mass effectively and safely can be challenging. This study proposes a new system of arranging the mass in the experiments that combines the realism of mass participation during earthquake excitation when supported by the shake table with laboratory practicality considerations of the mass positioned off the specimen. The characteristics and dynamic motion equations for the proposed system are described and applied to shake table experiments involving large-scale …