Characterization Of Sediment Loads And Size Distribution In Nebraska Roadway Runoff, Bruce I. Dvorak, David M. Admiraal, Pavel Shrestha

Nebraska Department of Transportation: Research Reports

The Nebraska Department of Transportation (NDOT) must manage sediment, and pollutant loads from roadway runoff to meet stormwater regulations. The SAFL Baffle, a hydrodynamic separator used by NDOT, depends on reliable estimates of total suspended solids (TSS) and particle size distribution (PSD). However, limited data exists for Nebraska roadways. In this study stormwater runoff was monitored at four NDOT-maintained sites, two in Lincoln and two in Beatrice, over 1.5 years to characterize TSS and PSD and to evaluate SAFL Baffle performance using the SHSAM model. Results showed large variability across sites and seasons. Median TSS ranged from 158 to 580 …

Performance And Mechanistic Insights Into Cement Systems Modified With Wastewater-Recovered Struvite, Ugochukwu Ewuzie, Rupack R. Halder, Abdulkareem O. Yusuf, Abiodun A. Saka, Godwin I. Ogbuehi, Titus C. Egbosiuba, Damilola A. Daramola, Monday Uchenna Okoronkwo

Chemical and Biochemical Engineering Faculty Research & Creative Works

Struvite, the stable hydration product and primary strength phase in magnesium ammonium phosphate cement (MAPC), derived from wastewater treatment, has recently been utilized as a sustainable additive to Portland cement (PC). However, its impacts on cement hydration kinetics, pore refinement, rheology, and the mechanisms underlying these processes have not been comprehensively studied. This study developed Portland cement-struvite (PCS) systems by replacing PC with 3–20 % struvite (ST wt.%: PCS3–PCS20) and evaluated these processes using isothermal calorimetry, 3D micro-computed tomography (μXCT), time-dependent rheometry, X-ray diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR), and the Krstulović-Dabić (K-D) model. The FTIR/XRD confirmed the coexistence …

Artificial Neural Network Model For Predicting Fatigue Endurance Limit Of Hot Mix Asphalt Using Uniaxial Tension–Compression Tests, Prashanta Kumar Acharjee, Mayzan Isied, Mena I. Souliman, Sameer Jung Karkl, Tanvir Ahmed, Gokhan Saygili

Civil Engineering Faculty Publications and Presentations

Fatigue is one of the major distresses occurring in asphalt concrete pavement. Repeated traffic loading causes escalated structural damage which results in the formation of cracks. There is a strain level below which the Hot Mix Asphalt goes under fatigue failure, and it is called endurance limit. In this study, a predictive model is developed to predict endurance limit strain values by using artificial neural network. Uniaxial tension-compression fatigue test results conducted under NCHRP Project 9–44 A were utilized in the model development process. An equation is also extracted from the model along which gives the exact values as the …

City Farm Slo Sheep Shed Concrete Slab Installation, Jake Simkins, Elijah Burt, Finnbarr Kelly

Construction Management

The City Farm SLO Sheep Shed Foundation Slab project, undertaken by California Polytechnic State University, San Luis Obispo Construction Management students, aimed to improve the structural integrity and longevity of an existing livestock shelter at City Farm SLO. Initiated in coordination with Shane Lovell, owner and operator of City Farm SLO, and guided by Construction Management faculty member Mark Montoya, the project integrated community service with practical application of structural concrete construction principles. The scope involved temporarily removing an existing sheep shed from within an active livestock pen, preparing subgrade in muddy winter conditions, and constructing a reinforced 5-inch, 4500 …

Co-Calcination Of Limestone And Clay Enhances The Performance Of Limestone Calcined Clay Cement (Lc3), Oluwadamilare Charles Adesina, Sahil Surehali, Avinaya Tripathi, Kayla Lauren Lee, Bryan K. Aylas-Paredes, Aditya Kumar, Narayanan Neithalath

Materials Science and Engineering Faculty Research & Creative Works

Limestone-calcined clay cements (LC³) reduce the environmental impact of cement production and accelerate the industry transition toward carbon neutrality. While conventional LC³ with 50% clinker replacement (LC³-50) demonstrate long-term performance comparable to ordinary Portland cement (OPC) in concrete, early-age performance is generally compromised. This study explores for the first time, joint thermal treatment—that is, co-calcination—of limestone (LS) and bulk kaolinitic clay in mass ratios of 1:1 to 1:4 under a calcination regime specifically designed to ensure activation of the clay mineral. The co-calcination converts a small fraction of LS to metastable CaO, thus providing an …

Efficiency Evaluation Of Different Methods For Nitrogen Removal In Municipal Wastewater Treatment Plants: An Integrative Review, Cristiane G. Ferrarezzi, Juliana Canto Duarte

The School of Sustainability Engineering and Environmental Engineering (SEE) Graduate Student Publications

Domestic wastewaters present high nitrogen levels due to the urea and ammonia, which are excreted into urine. Municipal wastewater treatment plants (WWTP) normally face some challenges in keeping their treated wastewater at a low total nitrogen concentration, since the majority of their wastewater is domestic. Low nitrogen levels in the treated wastewater are important to avoid increasing eutrophication of the receptor body, which receives the treated wastewater. This work presents an integrative review considering studies related to denitrification in domestic WWTPs published from January 1st, 2018, to April 30th, 2023. This review aims to identify the most effective methods for …

Utilization Of Plastic Waste In The Concrete Industry, Nancy Abdelmoneim Sakr

Theses and Dissertations

Plastic recycling has emerged as a crucial strategy that aligns with environmental, social and economic sustainability indicators. Currently, substantial volumes of plastic waste are either deposited in landfills or incinerated, neglecting the potential to harness its embodied energy and the energy consumed for producing virgin materials. A key advantage of plastic lies in its promising mechanical properties. Concrete mix design is fundamental to a wide range of construction applications, including brick walls, reinforced concrete slabs and concrete pavements. Despite the adoption of recycled plastic in construction materials in various countries, its widespread implementation remains limited. This is primarily due to …

Mechanical Properties And Reproducibility Of One-Part Ambient-Cured Slag And Fly Ash-Based Geopolymer Concrete, Daro Sun, Jessey Lee, Alireza Mohyeddin, Janitha Migunthanna

Research outputs 2022 to 2026

The cement industry is a major source of anthropogenic CO2 emissions due to its energy-intensive production process and calcination of limestone. Producing one ton of cement emits approximately one ton of CO2, and cement accounts for about 5% to 8% of global CO2 emissions. In this context, cement-less one-part (“just-add-water”) ambient-cured geopolymer concrete (GPC) has gained attention due to its environmental friendliness and practicality for large-scale cast-in-situ construction. However, field adoption remains limited, mainly due to the scarcity of data on mechanical properties and durability, as well as the lack of widely accepted standards and specifications. This paper is part …

Mining Waste As A Resource In Construction: Applications, Benefits, And Challenges, Chathurika Dassanayake, Nuha S. Mashaan, Daniel Oguntayo

Research outputs 2022 to 2026

Mining activities generate vast quantities of waste each year, including mine tailings, bauxite residue, waste rock, and various metallurgical slags. Although these materials have traditionally been regarded as environmental liabilities, many possess physical and chemical properties that make them promising candidates for use in construction. This review synthesizes recent research on the utilization of major mining waste streams, with particular emphasis on pavement applications and other construction materials. The findings indicate that bauxite residue exhibits both pozzolanic and filler characteristics, demonstrating potential in asphalt mastics, asphalt mixtures, and other construction products. Nonetheless, its widespread adoption is constrained by issues such …

Fiber-Reinforced Foam Concrete Using Quarry Micro Fines And Sugarcane Bagasse Ash: A Box–Behnken Design Optimization And Performance Assessment, Ravindaran Thangavel, Sanjay Kumar Shukla, Mini K. Madhavan

Research outputs 2022 to 2026

Foam concrete is well-appreciated for its thermal and acoustic benefits and is prepared by introducing foam into cement slurry/mortar. The current research examines the feasibility of Quarry Micro Fines (QMF), a waste generated from the quarries during sand manufacturing, as a substitute for fine aggregate in the preparation of foam concrete. During the preparation of concrete, a portion of cement is replaced with sugarcane bagasse ash (SCBA), while polypropylene (PP) fibers are added to improve the shrinkage resistance and tensile strength of the resulting concrete. A three-factor, three-level Box–Behnken Design (BBD) in Response Surface Methodology (RSM) was used to optimize …

Assessment Of Winter Maintenance Performance Objectives Using Maintenance Decision Support System, Curtis L. Walker, Mark R. Anderson, Aemal Khattak, Thomas Kauzlarich, Abdul Farhan

Nebraska Department of Transportation: Research Reports

It is important for transportation agencies to assess their winter maintenance operations performance to identify areas for improvement and/or resource investment to maintain optimal levels of service, mobility, and safety. This study explores nine winter snowstorms in Nebraska during the 2023-2024 winter season across 20 road segments, 12 of which were along the Interstate-80 corridor. Datasets explored include meteorological information, traffic mobility insights, winter maintenance operations activities, and road conditions before, during, and after the periods of accumulating snowfall. Statistical analyses explored correlations and quantitative relationships among these datasets, while visual dashboards were developed to promote more qualitative considerations of …

Resilience By Design: A Multi-Metric Assessment Of Urban Vulnerability Across Human-Centric, Built, And Climatic Environment Dimensions, Karim Abdelhady

Theses and Dissertations

Urban resilience and sustainability have emerged as fundamental imperatives in contemporary urban planning, as cities face mounting pressures from climate change, population growth, and increasing socio-economic disparities. Resilient urban systems are not only those that withstand shocks, but also those that ensure the long-term well-being, equity, and functionality of their environments. As such, advancing the capacity to systematically evaluate resilience across spatial and temporal scales is critical to informing adaptive, forward-looking planning strategies. Despite a growing body of research on urban resilience, prevailing approaches remain limited in scope and resolution. Many studies tend to examine resilience through isolated lenses—focusing either …

Multifunctional Green Wall Systems For Greywater Treatment And Hygrothermal Regulation In Egypt, Laila Ossama Mohamed Elhusseiny Abdelsalam

Theses and Dissertations

Increasing environmental concerns regarding climate change and the intensifying challenge of water scarcity in Egypt necessitate the development of innovative, sustainable, and resource-efficient strategies for wastewater reuse. In the built environment, greywater constitutes a significant, relatively low-contaminant wastewater stream that, if treated to comply with Egyptian Codes and relevant international standards, can be safely reused for non-potable applications such as irrigation, landscaping, and building services. This research investigates the efficacy of an integrated green wall panel system, installed on building façades, for decentralized greywater treatment under Egypt’s climatic and environmental conditions, while simultaneously enhancing hygrothermal performance to reduce building energy …

Design Of Novel Formwork System And Development Of Numerical Model For Comparison Between Formwork Systems, Ahmed Yehia Abdel Aziz El Sayed

Theses and Dissertations

The formwork industry has witnessed major breakthroughs in the last decades. However, they required huge amount of materials leading to negative environmental impacts. Also, the commercially available systems have big number of accessories and requires the extensive use of units to cover the areas to be poured. There was an attempt to target all these disadvantages by introducing the Funicular Arched Steel Truss (FAST) system. However, this system had its own drawbacks, and this is why the researcher introduced an extendable version named the “Extendable Funicular Arched Steel Truss (EAST) system.”

To reach the final version of the EAST design, …

A Bim-Based Flexible Flow Shop Framework For Scheduling Linear Infrastructure Projects, Mahmoud Mohamed Elbassuony

Theses and Dissertations

Repetitive, multi-stage linear projects, such as pipelines or highways, are primarily impacted by spatial and resource constraints during their execution. Cost overruns, delays, and inefficient resource allocation make construction management for such projects complex. Traditional scheduling techniques, such as Critical Path Method (CPM) and Line of Balance (LOB), are less efficient for scheduling dynamic, complex, and multi-objective projects. There are more advanced scheduling methods that can be applied as a decision-making process to determine the optimal timing of activities and achieve other objectives. One of those techniques is the Flexible Flow Shop model (FFS), which can be effectively applied to …

Fly Ash Proppant Developed For Hydraulic Fracturing, Raz Rzgar Haydar

Theses and Dissertations

Proppants are critical components in hydraulic fracturing, used to maintain fracture conductivity and enhance reservoir stimulation. In high-pressure and harsh reservoir environments, the use of high-strength proppants is essential to ensure well performance. Conventional proppants, being sand, ceramic, and sintered bauxite can be expensive, and their use often requires costly fracture fluids. This study investigates the possibility of utalizing fly ash geopolymers as a sustainable alternative that is also cost-effective for proppants manufacturing. Fly ash, a by-product from the combustion of coal and other materials, was explored as a base material for proppants, utilizing an alkaline solution as an activator …

Irrigation Efficiency In Green Wall Systems Utilizing Iot: Developing And Testing A Method To Optimize Water Use For Green Walls, Yomna Zaghloul

Theses and Dissertations

This study investigates the application of an Internet of Things (IoT)-based automated irrigation system for green walls in Cairo, Egypt, assessing its impact on water conservation, energy consumption, and plant health across a three-month experimental period. The research compared a sensor-controlled drip irrigation system utilizing the ESP8266 microcontroller and real-time environmental monitoring against conventional timer-based irrigation methods. Water usage data revealed that the IoT system consistently achieved substantial savings—averaging nearly 60% less water consumption than the control group—without compromising overall plant vitality. Energy efficiency was also improved, with automated cycles reducing pump operating time by more than 50%. Plant growth …

Towards Decarbonizing Concrete Industry In Egypt: Material Alternatives, And Economic Viability, Reem Gamal

Theses and Dissertations

The construction industry remains one of the largest contributors to global greenhouse gas emissions, with cement and steel production accounting for approximately 15% of total emissions. As global infrastructure demands continue to rise, there is an increasing need for practical tools that support low-carbon construction practices in line with international climate commitments. This research presents the development and testing of a mathematical, adaptable decision support system designed to assess both the environmental and financial impacts of material selection in concrete production. Focusing on life cycle stages A1 to A3, raw material extraction, transportation, and manufacturing, the decision support system enables …

The Effect Of The Socioeconomic Variety In Greater Cairo On Transport Mode Choices, Rafik Yanni

Theses and Dissertations

In the last decade, Egypt has experienced a noticeable upgrade in its infrastructure investment, implementing a lot of transport projects, especially in the Greater Cairo region. In a city with over 20 million residents, variations lie in socioeconomic elements like income, age, gender, and neighborhood, which shape people’s choice of mobility modes based on their culture and lifestyle. The questions then become: whom are these new projects targeting? What are the barriers to using these services? And is there any willingness to change commuting habits if conditions changed? This thesis investigates how the socioeconomic variety in Greater Cairo metropolitan region …

Performance, Economic And Environmental Evaluation Of A Solar-Assisted Vacuum Deaeration Heating System., Liew Shan Kun

Student Works (2020-2029)

This research evaluates the performance of a solar-assisted heating (SAH) system for makeup water in a vacuum deaeration process. The system integrates solar energy into the heating process, with parametric analysis conducted across varying configuration of total solar radiation and water flow rates. The total solar radiation at the experimental site in Kuala Kangsar, Perak, Malaysia, characterized by tropical weather, fell within the range between 414W/m2 to 568W/m2. Performance analysis showed that a flow rate of 0.4 LPM achieved the target temperature of 61°C required for the deaeration process. Thermal efficiency peaked at 62.60% under a solar radiation of 900 …

A Point-Cloud Data Analysis Framework For Early Deformation Detection, Avinash Pandey

Theses and Dissertations

Frost heave and thaw-related deformation threaten the performance of roads, runways, embankments, and buried utilities in cold regions, yet traditional inspections remain reactive and often miss early uplift. This study evaluates the capability of LiDAR (Light Detection and Ranging) to detect small-scale ground deformation and introduces a practical point-cloud framework designed for early-stage characterization. Controlled jack-lift experiments quantified handheld LiDAR accuracy at uplift increments of 6.35, 12.7, 19.05, and 25.4 mm, with corresponding detection accuracies of 88%, 86%, 93.33%, and 94%. Registration quality had a significant impact. The targetless scans showed slight misalignment, whereas spherical targets provided precise, repeatable outputs. …

Understanding Mobility Limitations And Public Transportation Accessibility For People With Disabilities, Jada Meria Stringer

ETDs from 2020-2029

Mobility for people with disabilities (PWDs) depends on both the availability of transportation and public services and the accessibility of these systems. The presence of public transportation systems does not ensure usability. Vehicles, infrastructure, and the built environment must be designed to accommodate diverse physical, sensory, cognitive, and other needs. PWDs must also be able to navigate public buildings and surrounding spaces safely and comfortably. This thesis examines mobility limitations for PWDs in India and the United States, focusing on accessibility along the full mobility chain. A review of existing literature provides context on accessibility policies, design standards, and the …

Hybrid Quantum-Classical Optimization Of The Resource Scheduling Problem, Tyler Christeson, Md Habib Ullah, Ali Arabnya, Amin Khodaei, Rui Fan

Electrical and Computer Engineering: Faculty Scholarship

Resource scheduling is critical in many industries, especially in power systems where the Unit Commitment (UC) problem determines the on/off status and output levels of generators under physical and economic constraints. Traditional exact methods, such as Branch-and-Bound, Branch-and-Cut, dynamic programming and mixed-integer linear programming (MILP), remain the backbone of UC solution techniques, but they often rely on linear approximations or exhaustive search, leading to high computational burdens as system size grows. Metaheuristic approaches, such as genetic algorithms, particle swarm optimization, and other evolutionary methods, have been explored to mitigate this complexity; however, they typically lack optimality guarantees, exhibit sensitivity to …

Advanced Control Strategy For Photovoltaic Dc Microgrids Using Model Predictive Control With Rl Filter Enhancement, Yagub Suleymanov

Student Theses and Dissertations

This thesis presents the modeling and control of a photovoltaic (PV)-based DC microgrid using MATLAB/Simulink. A DC–DC converter with a buck stage is employed to perform a better maximum power point tracking (MPPT) and voltage regulation from PV panel. Predictive control method (MPC) algorithm will be employed, which offers faster transient response and reduced oscillations compared to traditional techniques. Considering the existing works, this study introduces an additional RL filter branch to further improve the stability of the regulated DC bus voltage combining MPC method and Incremental Conductance Maximum Power Point Tracking (IC-MPPT) algorithm. To ensure stable operation of the …

Direct Solar-Energy Powered Hydrothermal Treatment To Promote Biomethane Production From Anaerobic Digestion Of Rice Processing Waste, Kainat Rahnuma

Student Theses and Dissertations

Hydrolysis is a slow and energy-intensive process and a rate-limiting step in anaerobic digestion (AD). This research investigates performance strategies for integrating hydrothermal treatment (HT) with AD. HT-AD systems were less economically viable than AD-only options because of the high energy consumption of HT. Therefore, we used solar energy to conduct HT via either solar cookers or solar panels. The HT method significantly improved digestion performance, reducing the lag phase from 60 to 24 h, and increasing overall yield. Hydrothermally treated rice, rice bran, and rice hulls produced 22,932 mL, 13,136 mL, and 1283 mL, respectively. However, untreated rice, rice …

Angular Scanning Method For Efficient Maximum Power Point Tracking, Saikot Hossain Dadon

Student Theses and Dissertations

The Photovoltaic System (PV) is one of the widely used sources of renewable energy. There are various control mechanisms to manipulate the PV system. However, one of the major control mechanisms is Maximum Power Point Tracking (MPPT) to extract the maximum power from the solar panel. The solar power is intermittent and stochastic in nature due to the unpredictable sunlight exposure to the solar panel and temperature variance throughout the day and year. Consequently, the PV module does not run at Maximum Power Point (MPP) naturally; therefore, an MPPT controller is utilized so that the solar panel runs in the …

Evaluating The Fate And Variability Of Soil Organic Carbon And Nitrogen Species Under Conservation Practices In The Raccoon River Watershed, Zhonglong Zhang, May Wu

Civil and Environmental Engineering Faculty Publications and Presentations

This study evaluates the fate and variability of soil organic carbon (SOC) stocks and nitrogen species using the latest version of the Soil and Water Assessment Tool– Carbon (SWAT-C) and assesses how conservation practices influence their dynamics in the Raccoon River Watershed (RRW). Dominated by intensive agricultural pro- duction, the RRW is a significant contributor of sediment and nutrient loads to local rivers and the Mississippi River. This SWAT-C model simulates the export of SOC and nitrogen species and evaluates their responses under varying management scenarios. Model calibration was performed for streamflow, sediment, nitrate, total nitrogen, and organic carbon with …

Energetics Analysis Of Solitary Waves Using A Multi-Layer Model, Hunter Boswell, Frank D. Han, Guirong Yan, Wouter Mostert

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study investigates the performance of a vertically-Lagrangian multi-layer model on numerically simulating shoaling and breaking two-dimensional solitary waves during both the breaking and post-breaking processes. The energy dissipation of the breaking event for the multi-layer waves is analyzed and compared to prior direct numerical simulation work with the same bathymetric and wave cases. It shows very similar data collapse to shallow-water inertial theory. For post-breaking behavior, bore characteristics are compared to an experimental study of bores formed from breaking solitary waves and similar results are found. While the multi-layer method was not found to behave sufficiently well for direct …

Influence Of Co2 Curing On Carbonation Depth, Phase Composition, And Micro-Mechanical Properties Of Fbc Ash-Blended Cementitious Materials, Heejung Jun, Seongho Han, Sanghwon Wi, Jinyoung Yoon

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study investigates the physicochemical and mechanical performance of cementitious composites incorporating fluidized bed combustion (FBC) ash under accelerated carbon dioxide (CO₂) curing. FBC ash, due to its high contents of free calcium oxide (CaO) and sulfate (SO₃), has been reported to cause challenges, such as volume instability and lower early-age strength. To address these limitations, CO2 curing was applied to promote accelerated carbonation and stabilize the hydration products. Cement paste and mortar samples, made with up to 40 % by cement weight replacement with FBC ash (labelled CF), were subjected to either CO₂ curing …

Trip Generation Model For Mixed-Use Development In Klang Valley, Malaysia., Goh Boon Hoe

Student Works (2020-2029)

Mixed-Use Developments (MXDs) are single development projects that integrate and interact with different land uses, such as offices, retail, restaurants, entertainment venues, hotels, and/or residential areas. MXDs are internally connected, allowing users of different land uses to share internal streets, walkways, driveways, and parking spaces. Traffic is estimated to be reduced with such developments. Currently, in Malaysia, there is no standard procedure to estimate the MXD trip generation rates. The Malaysian Trip Generation Manual (MTGM) 2010 is the guideline used to forecast future trips for a single land use and hence, by summing the trip generation rates for multiple land …