Civil and Environmental Engineering Commons^™

Influence Of Soil Fabric On Dynamic Properties Of Sand: An Experimental Study, Arpit Jain, Satyendra Mittal, Sanjay K. Shukla

Research outputs 2022 to 2026

Natural field sites originate under the action of external sources such as rivers, wind, or marine environments. These sources are responsible for constituting a variety of soil fabrics, which ultimately modify the deformation characteristics. Additionally, the dynamic properties of a site present the characterization of a region and have been profusely utilized by field engineers and researchers. In the present study, the dynamic properties of soil specimens have been evaluated for specimen preparation techniques, namely, air pluviation (AP) and water sedimentation (WS). The cyclic triaxial tests were conducted on the strain-controlled consolidated undrained specimens at a frequency of 0.1 Hz. …

Influence Of Surface Cracking, Anchor Head Profile, And Anchor Head Size On Cast-In Headed Anchors In Geopolymer Concrete, Trijon Karmokar, Alireza Moyheddin

Research outputs 2022 to 2026

In this study, the concrete cone capacity, concrete cone angle, and load–displacement response of cast-in headed anchors in geopolymer concrete are explored using numerical analyses. The concrete damaged plasticity (CDP) model in ABAQUS is used to simulate the behavior of concrete substrates. The tensile behavior of anchors in geopolymer concrete is compared with that in normal concrete as well as that predicted by the linear fracture mechanics (LFM) and concrete capacity design (CCD) models. The results show that the capacity of the anchors in geopolymer concrete is 30%–40% lower than that in normal concrete. The results also indicate that the …

Winter Dynamics Of Storm Water Management Ponds And Winter Tolerance In Three Aquatic Plant Species, Patrick Strzalkowski

Theses and Dissertations (Comprehensive)

The vast majority of the research into the performance of stormwater management ponds (SWMPs) has been performed in warm regions or during the warmer seasons in temperate regions. It is presumed that SWMPs are inactive in the winter as any potential stormwater is trapped in snow and ice. The main goal of this thesis was to test this presumption and to study the dynamics and performance of three SWMPs during the winter. Remote water level loggers were installed into the three SWMPs and daily grab samples from the influents and effluents were taken and analyzed for total phosphorus (TP), chloride, …

Faceted Nanomaterial Synthesis, Characterizations And Applications In Reactive Electrochemical Membrane Filtration, Qingquan Ma

Dissertations

Facet engineering of nanomaterials, especially metals and metal oxides has become an important strategy for tuning catalytic properties and functions from heterogeneous catalysis to electrochemical catalysis, photocatalysis, biomedicine, fuel cells, and gas sensors. The catalytic properties are highly related to the surface electronic structures, surface electron transport characteristics, and active center structures of catalysts, which can be tailored by surface facet control. The aim of this doctoral dissertation research is to study the facet-dependent properties of metal or metal oxide nanoparticles using multiple advanced characterization techniques. Specifically, the novel atomic force microscope-scanning electrochemical microscope (AFM-SECM) and density functional theory (DFT) …

Bioremediation Of Petroleum Hydrocarbons In Coastal Sediments, Charbel Abou Khalil

Dissertations

The biodegradation of dispersed crude oil in the ocean is relatively rapid (a half-life of a few weeks). However, it is often much slower on shorelines, usually attributed to low moisture content, nutrient limitation, and higher oil concentrations in beaches than in dispersed plumes. Another factor may be the increased salinity of the upper intertidal and supratidal zones since these parts of the beach are potentially subject to prolonged evaporation and only intermittent inundation. Therefore, two laboratory experiments are conducted to investigate whether such an increase in porewater salinity results in additional inhibitory effects on oil biodegradation in seashores.

In …

2022 Scholarly Productivity Report, Missouri University Of Science And Technology

Civil, Architectural and Environmental Engineering Scholarly Productivity Reports

No abstract provided.

A Progress Insight Of The Formation Of Hydrogen Rich Syngas From Coal Gasification, Tawanda Matamba, Stefan Iglauer, Alireza Keshavarz

Research outputs 2022 to 2026

This review paper aims to explore the research progress in the formation of hydrogen rich gas from different innovative coal gasification parameters. Promotion effects of parameters such as pressure, temperature, catalyst, coal type, reactor setup, and gasification agents (H2O, O2, supercritical water) were extensively analysed. The formation of hydrogen gas through coal gasification was sub-divided into H2 production from fixed bed gasification system, fluidized bed system, and entrained flow system. The advantages of coal and biomass co-gasification towards clean energy formation was also reviewed. Co-gasification and elevated temperatures, pressures, and steam-carbon ratios were reported to positively influence the yields of …

Assessing Morphological Changes Of The Msimbazi River Using Satellite Images, Fides J. Izdori

Tanzania Journal of Engineering and Technology (TJET)

This study assessed historical morphology changes of the Msimbazi River in Dar es Salaam City, Tanzania, following heavy rainfall events using historical Google earth images. The erosion and sedimentation processes that cause morphological changes of a river are also associated with flooding within the river catchments. In this study, the bank-line movement, erosion and sedimentation areas and changes in river section width were analyzed under three-time periods: 2005- 2012, 2012- 2018, and 2018- 2020. Data shows that, the timing for floods coincides with the historical records for heavy rains. It was found that, area in the upper reaches of the …

Concrete Technology In A Rapidly Growing Urban Environment – The Case Of Dar Es Salaam City, John K. Makunza Jkm

Tanzania Journal of Engineering and Technology (TJET)

Concrete is a building material that is used in great quantities second only to our use of water. The ingredient materials of concrete include cement, fine and coarse aggregates plus a reasonable amount of water, and sometimes additives. The construction of various structures like, residential buildings, commercial buildings, hospitals, schools, bridges, etc., needs good quality concrete. Good modern technologies are needed by the construction industry in order to effectively construct buildings which are durable. A study has been done with the main objective of assessing the concrete technologies existing in rapid growing cities in Sub-Sahara Africa like Dar es Salaam, …

Development Of An Operational Satellite-Based Flood Monitoring Model For Tanzania, Andrew Kimati

Tanzania Journal of Engineering and Technology (TJET)

Timely information during water related disasters is of utmost importance for flood preparedness and risk reduction. However, the conventional ground-based photographic monitoring of flooded areas is an expensive and time-consuming exercise. Satellite remote sensing is a quick and affordable approach that can be used for concurrent floods detection at different scales. This is important as it facilitates timely information for emergency response to disaster management departments, even in scarcely instrumented catchments. This study presents a novel approach for flood tracking using satellite image remote sensing science to map flood affected areas immediately after occurrence of rainfall events. An open-source water …

Analysis Of Ore Hand-Crushed Size Distribution For Grinding Process In The Artisanal And Small-Scale Gold Mines Production: A Case Study Of Nholi Mine, Bahi District, Malugu Tembo

Tanzania Journal of Engineering and Technology (TJET)

(ASGM) employed numbers of people compared to large-scale mines. The ASGM has been played a crucial role in poverty alleviation and rural development, particularly in developing countries. The mined ore is crushed and ground for beneficiation of gold. The grinding process involved the size reduction of blasted materials to acquire minerals of interest. This paper presents the size distribution of hand-crushed for blasted materials using sieve analysis and digital image processing. The sieve test results for hand-crushed blasted material of three muck-piles were ranged between 17 mm and 36 mm that is equivalent to 20% and 80% passings respectively, with …

Deployment Of Inductive Loop Vehicle Traffic Counters Along Trunk Roads In Tanzania, Daudi Simbeye

Tanzania Journal of Engineering and Technology (TJET)

As Tanzania's population grows, there is a greater demand for efficient, effective, and strong road design, as well as a smooth transportation system with a balanced traffic management network architecture. To plan for maintenance and expansion of such a vast network, a credible data inventory and network condition must be established. The deployment of vehicle inductor loop counters along Tanzanian trunk roads is presented in this paper. At test sites, inductor loop sensors and control cards were used to capture vehicle traffic data, which was then wirelessly sent using GSM technology for vehicle classification verification and storage for future road …

Energy Assessment Of E-Motorcycles As A Clean Transport Mode For Passenger Mobility: A Case Of Ilala District, Dar Es Salaam, John Shirima

Tanzania Journal of Engineering and Technology (TJET)

Electric motorcycles or e-motorcycles is a clean mode of road transport that present a prominent solution toward decarbonizing cities. Despite of e-motorcycles being cleaner than gasoline ones, at the moment, there is missing information whether it is feasible to replace gasoline motorcycles with e-motorcycles used for business transport purposes. This paper, therefore, presents the results comparing energy usage when using e-motorcycles and when using the gasoline motorcycles. The energy demand for driving passengers using an e-motorcycle in the precarious routes originated from Gongo la Mboto bus stop to Segerea bus stop, Buguruni Malapa, Gerezani bus stop, Kivukoni bus stop, and …

Analysis Of Methods Of Construction And Application Of Modern Anti-Radar Missiles, A S. Solonar, P A. Khmarski, B M. Mukhammedov, G Sh Tuganov

Technical science and innovation

The analysis of methods of construction and application of modern anti-radar missiles (ARM) is carried out. The analysis allowed us to identify the most distinctive features of ARM such as: high flight speed (600-1200 m/s), limited launch range, different flight paths and it is oriented towards the attacked radar, small effective distribution surface (ESR), due to a sharp increase in the weight and size characteristics of the homing head of the homing head outside the frequency range (from 0.5 to 40 GHz), radio electronic means of the ARM are not created, the large range and high speed of tuning the …

Analysis Of Possible Causes Of Industrial Injuries And Accidents At Coal Industry Enterprises, F U. Otabekov, M Z. Naimova

Technical science and innovation

In this article, the issues that a person may face unfortunate events due to a certain reason due to the influence of various dangerous and harmful factors in the course of his life activities are resolved. Depending on the type and degree of exposure or the cause of the accident, the type and degree of injury may also vary. In most cases, injuries and damages occur suddenly and can lead to unexpected and unexpected consequences. Let's imagine that an unfortunate event happened by chance. In this situation, many people lose their senses, start to panic, hurry, become overly nervous or …

A Chemical Study Of Archaeometallurgical Ceramics From Southwestern Tanzania, Edwinus Lyaya

Tanzania Journal of Engineering and Technology (TJET)

Archaeometallurgical ceramics, including furnaces, tuyères, and potteries, were required for successful pre-industrial iron smelting and refining. However, there are limited chemical studies on archaeometallurgical ceramics in Tanzania. This paper examined the nature of clay source in terms of refractoriness, determined whether there were multiple clay sources, and verified the refractoriness of the archaeometallurgical ceramics. An x-ray fluorescence (XRF) analytical technique and experimental re-firing of the archaeometallurgical ceramics were employed. The chemical data clustered in the mullite region on the Al2O3-SiO2-FeO ternary system indicate that iron smelters and refiners chose refractory clay sources for making archaeometallurgical ceramics. Small range and standard …

Characteristics Of Extreme Precipitation And Their Effect On Bean Yield In Rwanda, Paul Ts Limbu Sr

Tanzania Journal of Engineering and Technology (TJET)

This study examines the characteristics of extreme precipitation and its effect on bean yield in Rwanda from 1981 to 2017. Over the study area, two rainy seasons, March to May (MAM) and September to December (SOND), account for approximately 80% of total rainfall. The spatial distribution of rainfall over Rwanda revealed that the first three EOF modes of MAM rainfall vary by 72.72 percent over the study period, while the first three EOF modes of SOND rainfall vary by 57.48 percent. The spatial analysis of extreme precipitation reveals that during wet years, the majority of the country's western regions receive …

Effect Of Hot Weather Concreting On The Mechanical And Durability Properties Of Concrete-A Review, Rawan Ramadan, Hassan Ghanem, Jamal Khatib, Adel Elkordi

BAU Journal - Science and Technology

Nowadays, hot weather is an essential motivator that leads concrete to lose its special characteristics. The high loss of moisture by evaporation and rapid hardening encourage the cracking potential and placement operations. The fresh mixed and hardened concrete tend to be damaged due to several conditions such as: high concrete temperature, High ambient temperature, low relative humidity, and high wind speed. These circumstances accelerate the rate of moisture loss and cement hydration. This article briefly reviews hot weather concreting problems precautions, and curing methods and also discusses the role of incorporation SCMs in reducing the temperature of concrete and enhancing …

Assessing The Influence Of Overweight Axles On Rutting Lives In Flexible Pavements Using Parametric Survival Analysis, Ali Hatoum, Jamal Khatib, Firas Barraj, Adel Elkordi

BAU Journal - Science and Technology

The existence of rutting or permanent deformation on flexible pavement layers has always been a concern that negatively affects the performance of roads by reducing the lifespan of pavement structure and by posing a safety risk for vehicles over the road. Traffic overloading is one of the primary factors that accelerates the deterioration of flexible pavement. This study aims to determine the time to failure of the flexible pavement structures associated with rutting, to indicate the most significant factors affecting rutting, and to assess the influence of overweight axles on pavement rutting life using parametric survival analysis. The data used …

Damage Stability Study Of A 500 Dw Ro-Ro Ferry Vessel, Zulfaidah Ariany, Budhi Santoso, Sarwoko Sarwoko, Nauval Abdurrahman Prasetyo

Makara Journal of Technology

The development of the crossing transportation industry is currently increasing in the island areas. The use of Ro-Ro type ferry boats is extremely efficient in moving people, goods, and vehicles. The current research focuses on the damage stability of the 500 DWT Ro-Ro ferry, which aims to meet the needs of the Ro-Ro ferry in the archipelago area. The previously existing initial design of a barge hull with a main size Lpp = 40.15 m, B = 12 m, H = 3.2 m, and T = 2.15 m was used to analyze the damage stability condition further. First, the drawings …

Fire-Resistance Testing Procedures For Construction Elements—A Review, Shashikant Chaturvedi, Ajitanshu Vedrtnam, Maged A. Youssef, Martin T. Palou, Gonzalo Barluenga, Kishor Kalauni

Civil and Environmental Engineering Publications

Fire accidents are a significant risk to human life and civil infrastructure. As a countermeasure, the regulatory bodies of different countries have established standards for evaluating the performance of construction elements during fire exposure. ISO 834 is the globally accepted fire-resistance testing standard. Other standards include ASTM E119, BS 476, IS 3809, JIS A 1304, AS 1503, EN 1363, and GB/T 9978, which are utilized by the US, Britain, India, Japan, Australia, Europe, and China, respectively. This article presents a summary and comparison of the fire-resistance testing standards. In reality, standard tests for isolated structural members may not efficiently portray …

Using Naming Conventions To Facilitate Data Transfer Between Asset Management Systems And Building Information Models, John D. Foster

Theses and Dissertations

An improvement to the workflow developed by Loeh et al. (2021) is proposed using a Revit template with BUILDER SMS naming conventions when creating the Sustainable Facility Management-enhanced BIM Model. The method presented by Loeh et al. (2021) is modified by integrating BUILDER SMS parameters and naming conventions into the BIM model during, as opposed to after, the creation of the model. Four building models created in 2020-21, four from 2021-22, and one building from 2019 were used in this study. Two groups of students were used to evaluate the effect of the building-specific BIM templates. Evaluating the 2020 and …

Design, Concept, And Visualization Of Urban Multi-Level Growing Table Systems In Hyper Urban Areas, Aaryan Manoj Nair, Shaheed Mohammed, Omar Rahama

Publications and Research

As of a 2019 study conducted by the National Urban Gardening Program (National Urban Gardening Program), urban farming accounts for approximately 19% of the total national farming output and is expected to triple to almost 45% by 2025. There is intensive research being conducted on aspects of reduced recidivism, communal health benefits, natural carbon capture systems, improved urban ecology and the necessity for reducing the carbon footprint of food, (informally dubbed “food miles”) there is little substantive research on optimisation, and maximation of crop productivity in hyper-urban areas.

The purpose of this report is to understand the functionalities of urban …

Deep Learning Models For Analysis Of Non-Destructive Evaluation Data To Evaluate Reinforced Concrete Bridge Decks: A Survey, Dayakar Naik Lavadiya, Sattar Dorafshan

Civil Engineering Faculty Publications

Application of deep learning (DL) for automatic condition assessment of bridge decks has been on the raise in the last few years. From the published literature, it is evident that lot of research efforts has been done in identifying the surface defects such as cracks, potholes, spalling and so forth using supervised learning methods such as deep learning. However, the health of a reinforced concrete bridge deck is jeopardized substantially due to presence of subsurface defects. Subsurface defects in bridge decks are genearlly detected using non-destructive evaluation (NDE) methods. Interpertation of NDE data for autonomous deck evaluation requires development of …

Energy Dissipation In A Sand Damper Under Cyclic Loading, Ehab Sabi

Civil and Environmental Engineering Theses and Dissertations

Various seismic and wind engineering designs and retrofit strategies have been in development to meet structures' proper and safe operation during earthquake and wind excitation. One such method is the addition of fluid and particle dampers, such as sand dampers, in an effort to reduce excessive and dangerous displacements of structures. The present study implements the discrete element method (DEM) to assess the performance of a pressurized sand damper (PSD) and characterize the dissipated energy under cyclic loading. The idea of a PSD is to exploit the increase in shearing resistance of sand under external pressure and the associated ability …

Leveraging Crowdsourced Navigation Data In Roadway Pluvial Flash Flood Prediction, Arefeh Safaei-Moghadam

Civil and Environmental Engineering Theses and Dissertations

This dissertation develops and tests a new data-driven framework for short-term roadway pluvial flash flood (PFF) risk estimation at the scale of road segments using crowdsourced navigation data and a simplified physics-based PFF model. Pluvial flash flooding (PFF) is defined as localized floods caused by an overwhelmed natural or engineered drainage system. This study develops a data curation and computational framework for data collection, preprocessing, and modeling to estimate the risk of PFF at road-segment scales. A hybrid approach is also developed that couples a statistical model and a simplified physics-based simulation model in a machine learning (ML) model to …

Estimating Vehicle Infrastructure: Downtown Albuquerque, New Mexico, Zachery Phillip Baiamonte

Architecture and Planning ETDs

Cities have little knowledge about their parking infrastructure despite clear evidence that abundant parking has environmental, economic, and transportation consequences. The objective of this thesis is to illustrate the need to accurately estimate the area dedicated to vehicle infrastructure (parking lots and streets) within urban areas. I focused on a method that estimated the vehicle infrastructure area within the Downtown Core of Albuquerque, New Mexico, by cross-referencing geospatial cadastral data with minimum parking requirements. Three parking space types were identified: 1) parking in structures; 2) surface parking (parking lots and residential driveways); and 3) on-street parking. To illustrate the need …

Reduction Of Embodied Carbon In Buildings Through Use Of Low Carbon Strategies And Standardization And Enforcement Of Life Cycle Assessment, Bhargavi Sai Sudhakar

Master's Projects and Capstones

The building and construction industry is energy intensive and as of 2021, this industry is responsible for 37% of the total global greenhouse gas emissions. In previous studies of conventional buildings, the operational energy of a building contributed to 80% and the embodied energy contributed to 20% of the total life cycle energy. With increase in policies and standards that focus on reducing the operational energy, low energy and certified green buildings have emerged where the operational energy has considerably reduced. The relative and absolute share of embodied energy in these energy efficient buildings have increased due to excessive use …

Polyelectrolyte Functionalized Forward Osmosis For Water Reclamation From Synthetic Spacecraft Wastewater, Alina Ripp

Electronic Theses and Dissertations, 2020-2023

This study investigated the application of a polyelectrolyte (PE)-assisted metallic iron nanoparticle-integrated forward osmosis (FO) membrane to treat synthetic spacecraft wastewater comprising urea, ammonium carbonate, and linear alkylbenzene sulfonate (LAS). The draw solution (MgSO4) diluted via the FO operation was further treated using a nanofiltration (NF) membrane aimed at producing potable quality water by the FO-NF hybrid process. A cellulose triacetate FO membrane was functionalized by layer-by-layer deposition of polyallylamine hydrochloride (PAH) and polyacrylic acid (PAA) followed by incorporating zero valent iron nanoparticles (ZVINP) within the "bilayers". It required 14 bilayers to ensure a uniform coating as demonstrated via scanning …

Performance Analysis Of A Solar-Driven Integrated Direct-Contact Membrane Distillation And Humidification–Dehumidification System, Abdellah Shafieian, Amin Roostaee, Pooria Behnam, Mehdi Khiadani

Research outputs 2022 to 2026

Despite significant advantages of solar-driven membrane-based distillation systems, their large-scale application is limited due to high energy losses, and low technical and economic feasibility. To overcome the mentioned issues, a Direct-Contact Membrane Distillation (DCMD) module (as the primary distillation stage) was coupled with a hollow-fibre membrane-based air humidification–dehumidification (HD) unit (as the secondary distillation stage) to increase the water productivity of the system by recovering some of the lost energy in the first stage. The membrane-based humidifier was designed and implemented instead of the conventional packed columns to avert their drawbacks of being bulky, complex, less durable, and less reliable. …