Civil and Environmental Engineering Commons^™

Numerical Simulation Of Concrete Beams With Discontinuity Regions Reinforced With Nonmetallic Reinforcing Bars, Amena Mohammad Ousama

Theses

Nonmetallic Glass Fiber-Reinforced Polymer (GFRP) reinforcing bars are considered a viable alternative to the conventional steel reinforcement because of their high strength-to-weight ratio and noncorrosive nature. This research aimed to investigate the nonlinear structural behavior of GFRP-reinforced concrete beams with discontinuity regions (D-regions) through numerical analysis. Three-dimensional (3D) numerical models were developed to simulate the nonlinear structural behavior of GFRP-reinforced deep beams with and without web openings. The models adopted realistic constitutive laws that accounted for the nonlinear behavior of the materials used. Predictions of the numerical models were validated against published experimental data. A parametric study was conducted to …

Estimating The Impact Of Intersection Traffic On Air Quality Emissions At Camden Cooper Medical Health Intersection Through The Integration Of Vissim/Moves Models, Kourtney Nicole Arena

Theses and Dissertations

Traffic emissions near intersections can increase significantly due to idling as well as stop-and-go traffic conditions. Increased emissions of pollutants like particulate matter (PM), nitrogen oxides (NOx), carbon monoxide (CO), and polycyclic aromatic hydrocarbons (PAHs) found in traffic exhaust deteriorate the health of the population that is exposed to them. Since general traffic emissions are increased by the stop-and-go conditions produced at intersections, PAH traffic emissions should also increase from intersection driving conditions. The intersection of Dr. Martin Luther King Jr. Blvd and Haddon Ave in Camden, NJ was identified as an ideal site to study PAH traffic emissions. To …

Inventory, Operations, And Safety At Free Right-Turn Ramps, Aemal Khattak, Jonathon Camezind, Mm Shakui Haque

Nebraska Department of Transportation: Research Reports

This research focused on traffic safety and operational performance of rural, minor approach stop-controlled intersections with free right-turn (FRT) ramps. The objectives of the research were to:

• Create a statewide inventory of rural FRT ramp intersections and provide to the Nebraska Department of Transportation (NDOT),
• Using NDOT 10-year crash data, conduct statistical safety analysis of rural FRT intersections extending ¼-mile in each direction from the intersection,
• Study vehicular operations at rural intersections with and without FRT ramps including a comparison of vehicular conflicts, and
• Develop guidelines for operations and safety tradeoffs to assist with NDOT projects on maintaining similar locations, …

Nebraska Balanced Mix Design – Phase I, Farzad Yazdipanah, Mahdieh Khedmati, Hamzeh Haghshenas

Nebraska Department of Transportation: Research Reports

Balanced mix design (BMD) is an alternative concept for designing asphalt mixtures that mainly focuses on performance of mixtures rather than only volumetric analysis. Using this concept, it would be possible to account for the incorporation of recycled asphalt mixtures, warm technology, polymers, rejuvenators, and other foreign additives, as well as external effective factors on the mix design such as environmental effects. This project sought to investigate performance-based methodologies for the asphalt mix design by taking a step to develop a preliminary Nebraska BMD framework. With that, selection of appropriate performance tests, finding a functional laboratory aging protocol, and defining …

Engineering A Multicompartment In Vitro Model For Dorsal Root Ganglia Phenotypic Assessment, Sydney M. Caparaso, Adan Redwine, Rebecca A. Wachs

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Despite the significant global prevalence of chronic pain, current methods to identify pain therapeutics often fail translation to the clinic. Phenotypic screening platforms rely on modeling and assessing key pathologies relevant to chronic pain, improving predictive capability. Patients with chronic pain often present with sensitization of primary sensory neurons (that extend from dorsal root ganglia [DRG]). During neuronal sensitization, painful nociceptors display lowered stimulation thresholds. To model neuronal excitability, it is necessary to maintain three key anatomical features of DRGs to have a physiologically relevant platform: (1) isolation between DRG cell bodies and neurons, (2) 3D platform to preserve cell–cell …

Devices And Methods For Removing Perflourinated Compounds From Contaminted Water, Dibakar Bhattacharyya Phd, Anthony Saad Phd, Rollie Mills Phd, L. E. Ormsbee Phd, M Abdul Mottaleb Phd

Civil Engineering Faculty Patents

PFAS compounds have emerged as a persistent and harmful environmental pollutant that present significant challenges to health and remediation. This patent describes a new technology that employs membrane technology along with thermo-responsive adsorption-desorption processes to remove perfluorinated compounds from contaminate water.

Post-Processed Data And Graphical Tools For A Conus-Wide Eddy Flux Evapotranspiration Dataset, J. M. Volk, J. L. Huntington, F. Melton, B. Minor, T. Wang, S. Anapalli, R. G. Anderson, S. Evett, A. French, R. Jasoni, N. Bambach, W. P. Kustas, J. Alfieri, J. Prueger, L. Hipps, L. Mckee, S. J. Castro, M. M. Alsina, A. J. Mcelrone, M. Reba, B. Runkle, M. Saber, C. Sanchez, E. Tajfar, R. Allen, M. Anderson

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Large sample datasets of in situ evapotranspiration (ET) measurements with well documented data provenance and quality assurance are critical for water management and many fields of earth science research. We present a post-processed ET oriented dataset at daily and monthly timesteps, from 161 stations, including 148 eddy covariance flux towers, that were chosen based on their data quality from nearly 350 stations across the contiguous United States. In addition to ET, the data includes energy and heat fluxes, meteorological measurements, and reference ET downloaded from grid- MET for each flux station. Data processing techniques were conducted in a reproducible manner …

Soybean Crop Coefficients Under Different Seeding Rates And Full And Limited Irrigation And Rainfed Management, Suat Irmak, Rupinder Sandhu

Department of Agricultural and Biological Systems Engineering: Faculty Publications

The effects of soybean seeding rates on evapotranspiration (ET_c) and grassand alfalfa-reference crop coefficients (K_co and K_cr) were investigated under five seeding rates (185,250, 247,000, 308,750, 370,500 and 432,250 seeds ha^-1) (62, 82, 103, 124 and 144% of the recommended seeding rate of 300,000 seeds ha^-1 in the experimental region) and different irrigation strategies (i.e. full irrigation treatment [FIT], limited irrigation of 75% FIT and 50% FIT and rainfed treatment). K_co and K_cr values were developed for each soybean growth stage. The seasonal ET_c ranged from 460 mm for …

Fate And Transport Of Per- And Polyfluoroalkyl Substances (Pfas) At Aqueous Film Forming Foam (Afff) Discharge Sites: A Review, Jeffery T. Mcgarr, Eric G. Mbonimpa, Drew C. Mcavoy, Mohamad R. Soltanian

Faculty Publications

Per- and polyfluorinated alkyl substances (PFAS) are an environmentally persistent group of chemicals that can pose an imminent threat to human health through groundwater and surface water contamination. In this review, we evaluate the subsurface behavior of a variety of PFAS chemicals with a focus on aqueous film forming foam (AFFF) discharge sites. AFFF is the primary PFAS contamination risk at sites such as airports and military bases due to use as a fire extinguisher. Understanding the fate and transport of PFAS in the subsurface environment is a multifaceted issue. This review focuses on the role of adsorbent, adsorbate, and …

Streambank Erosion Phenomena And Understanding: Current Research And Future Directions, Celso Castro-Bolinaga, Aaron R. Mittelstet, Kyle Mankin

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Streams are in dynamic equilibrium with their environments, and as that environment is altered by human development and changing climate, streambank erosion is a common, but little understood, result. This article highlights the contributions of the special collection “Streambank Erosion, Sediment Dynamics, and Restoration (SER),” which assembled six studies that represent key advances in streambank erosion research, highlight current research in the field, and identify directions for future research. The studies in this special collection were grouped into three central themes: (1) streambank erosion monitoring, (2) streambank erodibility characterization, and (3) streambank erosion loading. In this article, key findings within …

Toward Automated Irrigation Management With Integrated Crop Water Stress Index And Spatial Soil Water Balance, Sandeep Bhatti, Derek M. Heeren, Susan A. O’Shaughnessy, Christopher M. U. Neale, Jacob Larue, Steve Melvin, Eric Wilkening, Geng Bai

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Decision support systems intended for precision irrigation aim at reducing irrigation applications while optimizing crop yield to achieve maximum crop water productivity (CWP). These systems incorporate on-site sensor data, remote sensing inputs, and advanced algorithms with spatial and temporal characteristics to compute precise crop water needs. The availability of variable rate irrigation (VRI) systems enables irrigation applications at a sub-field scale. The combination of an appropriate VRI system along with a precise decision support system would be ideal for improved CWP. The objective of this study was to compare and evaluate two decision support systems in terms of seasonal applied …

Toward Automated Irrigation Management With Integrated Crop Water Stress Index And Spatial Soil Water Balance, Sandeep Bhatti, Derek M. Heeren, Susan A. O’Shaughnessy, Christopher M. U. Neale, Jacob Larue, Steve Melvin, Eric Wilkening, Geng Bai

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Decision support systems intended for precision irrigation aim at reducing irrigation applications while optimizing crop yield to achieve maximum crop water productivity (CWP). These systems incorporate on-site sensor data, remote sensing inputs, and advanced algorithms with spatial and temporal characteristics to compute precise crop water needs. The availability of variable rate irrigation (VRI) systems enables irrigation applications at a sub-field scale. The combination of an appropriate VRI system along with a precise decision support system would be ideal for improved CWP. The objective of this study was to compare and evaluate two decision support systems in terms of seasonal applied …

Remote Sensing And Artificial Intelligence-Based Modeling And Prediction Of Harmful Algal Blooms In Lake Pontchartrain, Ian Smith

LSU Master's Theses

Harmful Algal Blooms (HABs) and particularly toxic cyanobacterial harmful algal blooms (CyanoHABs) have become a growing threat to the environment, economy, communities, and human and animal health. This is particularly true for Lake Pontchartrain. Forecasting the occurrence of cyanobacterial HABs in Lake Pontchartrain is a process that currently does not exist, as nowcasting by the NCCOS Algal Bloom Monitoring System or the similar system implemented by the U.S. EPA is currently the only method to monitor HAB production in the Lake. This thesis made this process possible by identifying antecedent environmental conditions controlling CyanoHABs, describing the conditions using NASA satellite …

Assessing The Release Of Microplastics And Nanoplastics From Plastic Containers And Reusable Food Pouches: Implications For Human Health, Kazi Albab Hussain, Svetlana Romanova, Ilhami Okur, Dong Zhang, Jesse Kuebler, Xi Huang, Bing Wang, Lucia Fernandez-Ballester, Yongfeng Lu, Mathias Schubert, Yusong Li

Department of Civil and Environmental Engineering: Faculty Publications

This study investigated the release of microplastics and nanoplastics from plastic containers and reusable food pouches under different usage scenarios, using DI water and 3% acetic acid as food simulants for aqueous foods and acidic foods. The results indicated that microwave heating caused the highest release of microplastics and nanoplastics into food compared to other usage scenarios, such as refrigeration or room-temperature storage. It was found that some containers could release as many as 4.22 million microplastic and 2.11 billion nanoplastic particles from only one square centimeter of plastic area within 3 min of microwave heating. Refrigeration and room-temperature storage …

Ecological Validity Of Immersive Virtual Environment Experiments On Human Thermal State And Behavioral Intentions: Experimental Protocol Factors, Girish Rentala

LSU Doctoral Dissertations

Using immersive virtual environment (IVE) based experiments to investigate human thermal states and thermal adaptive behaviors during the building design phase could help identify potential comfort issues and enable designers to optimize building performance cost-effectively before the actual building construction. However, to effectively utilize IVEs to study thermal states/adaptive behaviors, it is crucial to ensure the ecological validity of IVE experiment protocols. This entails accurately representing in-situ (real) environments within IVEs and establishing comparability and generalizability of data collected under different thermal stimuli between IVE and in-situ environments. Existing thermal stimuli based IVE studies have not effectively evaluated the ecological …

Behavioral Comparison Of Fluorescent Tracer Sediment To Lightweight Polystyrene Sediment Of The Lower Mississippi River Physical Model (Lmrpm), Julia C. Mudd

LSU Master's Theses

A lightweight, unexpanded polystyrene sediment with a specific gravity of 1.05 and a D10, D50 and D90 of 0.250 mm, 0.425mm, and 0.800 mm, respectively, is utilized in the Lower Mississippi River Physical Model (LMRPM) at Louisiana State University to mimic the sand transport of the Lower Mississippi River. While the black model sediment is easily visible against the stark white of the LMRPM, the relative homogeneity of the sediment particles and the opaqueness of the model channel make it difficult to closely study sediment dynamics during an experiment. For this reason, a tracer sediment that is marked with fluorescence …

Exploring Machine Learning In Deep Foundation And Soil Classification Application, Mohammad Moontakim Shoaib

LSU Master's Theses

The applicability of several Machine Learning (ML) models was explored in this research to predict the ultimate capacity and load-settlement behavior of axially loaded single-driven piles from Cone Penetration Test (CPT) data. Additionally, a common CPT-based soil behavior type (SBT) classification system was reproduced using those ML models. Eighty static pile load tests and corresponding CPT data close to those pile locations were collected from 34 sites in Louisiana for the deep foundation application. On the other hand, 70 CPT soundings were taken in 14 different parishes across Louisiana for the soil classification application. Specifically, tree-based ML models such as …

Using Bim To Increase The Efficiency Of Energy-Driven Retrofitting Projects, Anne Grego, Shannon Chance, Barry Mcauley

Conference Papers

The building sector is responsible for nearly 40% of global energy consumption. Many existing buildings have poor thermal insulation and low energy performance, hindering sustainability goals. Energy-driven building retrofitting could address this issue and implementing Building Information Modelling (BIM) in retrofitting can reduce process time, costs, and waste associated with such undertakings. Yet, there is a lack of research and insufficient guidance for implementing BIM in energy-driven retrofitting. A BIM framework is presented to enhance decision-making processes during retrofitting. The aims of this study were to (1) identify BIM technologies and methodologies that could address existing barriers and improve efficiency …

High-Throughput Phenotyping Of Plant Leaf Morphological, Physiological, And Biochemical Traits On Multiple Scales Using Optical Sensing, Huichun Zhang, Lu Wang, Xiuliang Jin, Liming Bian, Yufeng Ge

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Acquisition of plant phenotypic information facilitates plant breeding, sheds light on gene action, and can be applied to optimize the quality of agricultural and forestry products. Because leaves often show the fastest responses to external environmental stimuli, leaf phenotypic traits are indicators of plant growth, health, and stress levels. Combination of new imaging sensors, image processing, and data analytics permits measurement over the full life span of plants at high temporal resolution and at several organizational levels from organs to individual plants to field populations of plants. We review the optical sensors and associated data analytics used for measuring morphological, …

Evaluation Of Temperature-Index And Energy-Balance Snow Models For Hydrological Applications In Operational Water Supply Forecasts, Tian Gan, David G. Tarboton, Tseganeh Z. Gichamo

Civil and Environmental Engineering Faculty Publications

In the western United States, snow accumulation, storage, and ablation affect seasonal runoff. Thus, the prediction of snowmelt is essential to improve the reliability of water supply forecasts to guide water allocation and operational decisions. The current method used at the Colorado Basin River Forecast Center (CBRFC) couples the SNOW-17 temperature index snow model and the Sacramento Soil Moisture Accounting (SAC-SMA) runoff model in a lumped approach. Limitations in parameter transferability and calibration requirements for changing conditions with the temperature-index model motivated this research, in which new avenues were investigated to assess and prototype the application of an energy-balance snow …

Columbus, Nebraska: Southern Housing Development Design Proposal, Ryan Weyers, Caiden Dynek, Alex Papa, Brexton Robertson, Kaden Perala

Honors Program: Senior Projects (Public)

The following paper proposes the design and creation of a new housing development in the city of Columbus, Nebraska in a lot to the south of the city and directly north of the Columbus wastewater treatment plant. The goal of this proposal is to provide readers with confidence that our company is the most qualified to complete the project and will create the safest, most comfortable, most efficient, and most cost-effective final design. This proposal seeks to offer a solution to the lack of affordable housing for the growing workforce in Columbus. In order to arrive at this solution, each …

The Efficacy Of Conservation Practices In Reducing Floods And Improving Water Quality, Shivendra Srivastava, Andrea D. Basche, Elbert Traylor, Tirthankar Roy

Department of Civil and Environmental Engineering: Faculty Publications

Conservation practices such as crop rotation, filter strips, and constructed wetlands are nature-based approaches intended to safeguard natural resources in agricultural landscapes. In this study, we reviewed the literature on how conservation practices, both at watershed and field scales, have been proven to subdue flood peaks, surface runoff, soil erosion, sediment transport, and nutrient loss. We classified different conservation practices based on the mode of their application (i.e., in-field, edge-of-field, and structural practices) and described what prior research efforts have concluded about the efficacy of different practices. At the field scale, practices such as reduced or no-till farming, grassed waterways, …

Evaluating The Potential Of Geopolymer Concrete As A Sustainable Alternative For Thin White-Topping Pavement, Sathvik S. Chandra, Pshtiwan Shakor, Sarwar Mohmmad, Bankole O. Awuzie, Atul K. Singh, Abishek Rauniyar, M Karakouzian

Civil and Environmental Engineering and Construction Faculty Research

Introduction:

The construction industry uses a large quantity of natural materials in the production of concrete. Although attempts to incorporate green materials in concrete began years ago, not every building uses such materials today, and roadways, particularly, still rely on unsustainable materials.

Methods:

Therefore, this study used alternative materials, including fly ash, manufactured sand aggregates, and different molarities of alkaline activators, to incorporate waste byproducts in a geopolymer concrete white-topping pavement layer. Recent developments have led to the emergence of geopolymers as distinct classes of materials. In the 1990s, fly ash-based geopolymers became more popular than other kinds, as they …

Meta-Analysis Of Driving Behavior Studies And Assessment Of Factors Using Structural Equation Modeling, Duong Ngoc Hai, Chu Cong Minh, Nathan Huynh

Department of Civil and Environmental Engineering: Faculty Publications

The aim of this paper is to understand the factors that influence unsafe driving practices by examining published studies that utilized the Theory of Planned Behavior (TPB) to predict driving behavior. To this end, it reviews 42 studies published up to the end of 2021 to evaluate the predictive utility of TPB by employing a meta-analysis and structural equation model. The results indicate that these studies sought to predict 20 distinct driving behaviors (e.g., drink-driving, use of cellphone while driving, aggressive driving) using the original TPB constructs and 43 additional variables. The TPB model with the three original constructs is …

Strength As A Function Of Liquid Water Content In Different Snow Types - Results From Field Experiments Using A Blade Hardness Gauge, Mikael Schlumpf

Civil Engineering ETDs

The rapid weakening of snow layers that locally accumulate infiltrating liquid water is a well-known mechanism for wet slab avalanche formation. To quantify this process and improve the prediction of these destructive avalanches, a blade hardness gauge (BHG, a.k.a thin blade penetrometer) and SLF snow sensor were used to take 349 targeted paired measurements of strength and LWC, respectively, in the snow above 19 artificially wetted capillary barriers. Using a multiple regression analysis, we develop an expression for the blade hardness of manually wetted snow as a function of LWC, crystal form, and blade hardness prior to wetting. To understand …

Equity In Transportation: Data Driven Analysis Of Transportation Services And Infrastructures, Javad Jomehpour Chahar Aman

Civil and Environmental Engineering Theses and Dissertations

Achieving equity in transportation is an ongoing challenge, as transportation options still vary tremendously when it comes to marginalized populations. This dissertation addresses this challenge by conducting a comprehensive review of existing transportation equity literature and identifying two critical gaps: the lack of data-driven approaches to studying spatial mismatch between transportation supply and demand, and limited information on women's perceptions and expectations towards emerging transportation services.

Chapter two introduces the concept of transportation "deserts," specifically transit deserts and walking deserts, and develops data-driven frameworks to identify and investigate neighborhoods with limited transportation service supply but high demand. The frameworks compare …

A Mechanics-Based Analytical Solution For Restrained Beams With Application To Progressive Collapse Behavior, Leven Deputy

Civil and Environmental Engineering Theses and Dissertations

This dissertation presents an axially restrained beam (ARB) model that incorporates axial-flexural interaction throughout the entire static load-deflection curve: the elastic material range, the plastic, flexural dominant range, the range beyond plastic flexure with increasing catenary effect, and the full catenary range. Energy methods are applied to static load-deflection curves to determine dynamic load-deflection relationships. Specifically, this dissertation considers the two conditions; Pinned-Pinned-Pinned (PPP) which has no flexural resistance at the boundaries, and Fixed-Fixed-Fixed FFF (also Pinned-Fixed-Pinned, PFP) condition which provides the beam with flexural resistance at the boundaries equal to flexural capacity of the beam. Behavior is explained analytically …

3d Printing Of Earthen Materials: Toward The Carbon-Zero Construction, Shiva Bhusal

Civil Engineering ETDs

In recent years, digital manufacturing techniques in the architecture and construction industry have rapidly gained attention, especially with 3D printing, also called additive manufacturing. The use of cement has been common in modern construction and is now being explored for 3D printing. However, due to cement's contribution to approximately 7 percent of global carbon emissions and its high cost, research on sustainable and greener materials has gained attention. Previous studies on alternative construction have examined the mechanical and rheological properties of soil mixes, but not much attention has been given to printability evaluation, shrinkage, and cracking, which can affect the …

Additive Manufacturing Of Lightweight Concrete Mixtures, Kourosh Rashidi

Civil Engineering ETDs

Additive manufacturing, also known as 3D printing, is an innovative technique that is increasing its popularity in many industries including construction. 3D printing is related to the layer wised manufacturing or additive construction of any simple to intricate geometry from a digital file. The construction industry has a high potential for using 3D printing technology. However, one of the critical factors in the adaption of additive manufacturing in the construction industry is achieving a printable concrete mix design. This research aims to design printable mixes of lightweight concrete that could be effectively used in the 3D printing of walls or …

Evaluation Of The Geotechnical And Foundation Components On Jud Site, Mirabel W. Nkanor

Honors Theses

This thesis is part of the senior design final project of the Civil Engineering Department at the University of Mississippi. Geotechnical and foundation analyses were done on a proposed construction project for a multi-family home in Orlando, Florida. This evaluation done in this thesis follows the pre-existing geotechnical report on the side, USDA soil reports, ASCE Code 32-01 (Design of Foundations), and ASCE-7 Section 12.31.1 (Foundations and Superstructure-to-Foundation Connections).

A structural system was selected from the proposed location, on the corner of South Conway and Judge Road, and an evaluation of the Bearing Load capacity was completed to determine the …