Civil and Environmental Engineering Commons^™

Experimental Investigation Of The Thermochemical Reduction Of Arsenite And Sulfate: Low Temperature Hydrothermal Copper, Nickel, And Cobalt Arsenide And Sulfide Ore Formation, Nicholas Allin

Graduate Theses & Non-Theses

Experiments were conducted to determine the relative rates of reduction of aqueous sulfate and aqueous arsenite (As(OH)₃,aq) using foils of copper, nickel, or cobalt as the reductant, at temperatures of 150ºC to 300ºC. At the highest temperature of 300°C, very limited sulfate reduction was observed with cobalt foil, but sulfate was reduced to sulfide by copper foil (precipitation of Cu₂S (chalcocite)) and partly reduced by nickel foil (precipitation of NiS₂ (vaesite) + NiSO₄·xH₂O). In the 300ºC arsenite reduction experiments, Cu₃As (domeykite), Ni₅As₂, or CoAs (langisite) …

Analysis And Application Of Log-Linear And Quantile Regression Models To Predict Bus Dwell Times, Travis B. Glick, Miguel Figliozzi

Civil and Environmental Engineering Faculty Publications and Presentations

Understanding the key factors that contribute to transit travel times and travel time variability is an essential part of transit planning and research. Delay that occurs when buses service bus stops, dwell time, is one of the main sources of travel time variability and has therefore been the subject of ongoing research to identify and quantify its determinants. Previous research has focused on testing new variables using linear regressions that may be added to models to improve predictions. An important assumption of linear regression models used in past research efforts is homoscedasticity or the equal distribution of the residuals across …

Integrating Landsat Tm/Etm+ And Numerical Modeling To Estimatewater Temperature In The Tigris River Under Future Climate And Management Scenarios, Muhanned Al-Murib, Scott Wells, Stefan Talke

Civil and Environmental Engineering Faculty Publications and Presentations

Modeling the water quality of rivers and assessing the effects of changing conditions is often hindered by a lack of in situ measurements for calibration. Here, we use a combination of satellite measurements, statistical models, and numerical modeling with CE-QUAL-W2 to overcome in situ data limitations and evaluate the effect of changing hydrologic and climate conditions on water temperature (T_w) in the Tigris River, one of the largest rivers in the Middle East. Because few in situ estimates of Tw were available, remotely-sensed estimates of Tw were obtained from Landsat satellite images at roughly 2 week intervals for …

Behavior Of Geothermal Energy Piles Embedded In Rock, Ehab Sabi

Civil and Environmental Engineering Theses and Dissertations

Geothermal energy piles are categorized as closed systems. Energy piles are a relatively new technology which couples the structural role of traditional pile foundations to that of heat exchangers to fulfill the required energy demand of buildings and infrastructures. These foundations are equipped with pipes embedded in the concrete forming the pile. While connected to a heat pump, the fluid circulating inside these pipes provides the exchange of heat with the ground for heating and cooling purposes. As the undisturbed temperature at the shallower depths of the ground stays comparatively constant the whole year, being warmer than the surrounding temperature …

Impacts Of Freight Consolidation And Truck Sharing On Freight Mobility, Tieming Liu, Chaoyue Zhao

Data

Corresponding data set for Tran-SET Project No. 17ITSOKS02. Abstract of the final report is stated below for reference:

"The trucking industry is an important sector of the U.S. economy. However, it is quite fragmented, hindering the efficiency of cargo transportation and the ability for small carriers to identify demands to fill full truck loads. The focus of this research is to study models and algorithms in order to aid online freight marketplaces to identify efficient consolidation strategies. To accomplish this aim, a new mixed integer programming model for the pickup and delivery problem has been developed. The model is geared …

Daily And Seasonal Variability Of Offshore Wind Power On The Central California Coast And Statewide Demand, Matthew Douglas Kehrli

Physics

No abstract provided.

Characterization Of Air Dissolution And Reappearance Under Pressure In Cement Pastes By Means Of Rheology, Daniel Galvez-Moreno, Dimitri Feys, Kyle Riding

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Concrete pumping is the most used technique to transfer concrete from the mixer truck to the formwork. Numerous studies have been performed on the flow behavior of concrete in pipes, as well as the consequences of pumping on fluid and hardened concrete properties. One of the negative consequences of pumping concrete is a decrease in freeze-thaw resistance. This is caused by a decrease in air content and an increase in air bubble size, due to dissolution and reappearance of air and air bubble coalescence under pressure. This paper investigates the capability of rheology to understand air dissolution and reappearance in …

Determination Of Constructed Pavement Layer Thicknesses Using Nondestructive Testing (Ndt), Brad W. Rister, Jamie Creech, Kean H. Ashurst Jr.

Kentucky Transportation Center Research Report

Using nondestructive testing (NDT) to measure the thickness of pavement layers can improve the overall life of a new concrete and/or asphalt pavement. Conventional test methods require the extraction of a core from the pavement section to verify its thickness. Currently, two NDT technologies are commercially available which eliminate or reduce the need to core the existing pavement for thickness verification. The MIT-Scan-T2 (T2) utilizes magnetic pulse induction coupled with preset metal plates to obtain a thickness value. Measurements can be obtained quickly to an accuracy of +/– 2 mm. Ground Penetrating Radar (GPR) uses electromagnetic radiation to determine pavement …

Latent Choice Models To Account For Misclassification Errors In Discrete Transportation Data, Lacramioara Elena Balan

Civil & Environmental Engineering Theses & Dissertations

One of the most fundamental tasks when it comes to analyzing data using statistical methods is to understand the relationship between the explanatory variables and the outcome. Misclassification of explanatory variables is a common risk when using statistical modeling techniques. In this dissertation, we define ‘misclassification,’ as a response that is reported or recorded in the wrong category; for example, a variable is registered as a one when it should have the value zero. Misclassification can easily happen in any data; for example, in an interview setting where the respondent misunderstands the question or the interviewer checks the wrong box. …

Measuring And Modeling Bare Desert Wind Erosion From Steppe Grassland Of Northern China As Affected By Soil Moisture And Climate, Nicholas Morgan Potter

Civil & Environmental Engineering Theses & Dissertations

Soil erosion by wind has been found to be negatively related to soil water content, as evidenced by that for a given area, such a soil erosion can be much less in a wet than a dry year. However, few studies have examined the functional relationship between wind erosion and soil moisture, primarily due to lack of field measured data. The objectives of this study were to: 1) measure wind erosion in field using a portable wind tunnel devised and made by the author; 2) use the measured data to calibrate/validate a wind erosion model previously developed by the author; …

Variable Speed Limit Control At Sag Curves Through Connected Vehicles: Implications Of Alternative Communications And Sensing Technologies, Reza Vatani Nezafat

Civil & Environmental Engineering Theses & Dissertations

Connected vehicles (CVs) will enable new applications to improve traffic flow. This study’s focus is to investigate how potential implementation of variable speed limit (VSL) through different types of communication and sensing technologies on CVs may improve traffic flow at a sag curve. At sag curves, the gradient changes from negative to positive values which causes a reduction in the roadway capacity and congestion. A VSL algorithm is developed and implemented in a simulation environment for controlling the inflow of vehicles to a sag curve on a freeway to minimize delays and increase throughput. Both vehicle-to-vehicle (V2V) and infrastructure-to-vehicle (I2V) …

Sidestream Ras Fermentation For Stable Bio-P Combined With Short Cut Nitrogen Removal In An A/B Process, Lindsey Elise Ferguson

Civil & Environmental Engineering Theses & Dissertations

It is well known that soluble organic carbon (sCOD), especially in the form of volatile fatty acids (VFA), is critical to achieving reliable enhanced biological phosphorus removal (EBPR) in biological nutrient removal (BNR) processes. Consistent and reliable EBPR in systems treating wastewaters deficient in sCOD may be accomplished by the addition of VFA and sCOD – rich fermentate produced by the fermentation of primary sludge, return / waste activated sludge (RAS / WAS), or other suitable carbon sources. The solids retention time (SRT) of fermenters being used to supplement carbon in sidestream EBPR processes must be controlled such that complex …

Civil Engineering Design Of Cornhusker Council's Outdoor Education Center, Kelly Weiler

Honors Program: Senior Projects (Public)

A team of geotechnical, structural, hydraulic, environmental, and transportation experts collaborated to provide engineering solutions to the Cornhusker Council in an effort to solve the current problems facing their Outdoor Education Center. This results of this project provided the structural design of three bridges on the property, transportation plans for two parking lots and roadway design, geotechnical recommendations for soil testing and erosion prevention, and an environmental and hydraulic analysis of the property. A major challenge in the design of this project is the consideration of the dangers and regulations that accompany the floodway and floodplain regions on site. Various …

Fiber-Reinforced Polymer Bridge Girders For Extremely Aggressive Environments, Abdellah Emad Azeez

Doctoral Dissertations and Master's Theses

In 2012, the federal government estimated that $17.5 billion was spent on inspection, rehabilitation, maintenance, and replacement of the nation’s bridges. While the average lifespan of steel and reinforced concrete bridges is 50 years, certain bridges subjected to extremely aggressive marine environments may not reach this desired target. This research paper investigates using fiber-reinforced polymer (FRP) materials as primary bridge girders in medium span bridges (30 ft. to 75 ft.). The goal of this research is to identify the most efficient and cost-effective alternative for these corrosion-resistant materials and potentially extend the lifespan of these bridges up to 75 years. …

Austere Location Wind Turbine Energy System Analysis, Lukas Cowen, Douglas S. Dudis, Torrey J. Wagner

Faculty Publications

One promising technology to combat an energy shortage in austere locations is wind energy. In combination with battery storage and generator backup, we explore the feasibility of using a hybrid energy system to reduce the volume of diesel fuel required. Modeling the energy demands in austere locations will enable missions in remote settings to optimize their energy costs, increased their energy resiliency and assure their supply. For a modeled time-series energy requirement that varied between 2.4 MW and 5.1 MW, the optimal wind system size was 9.9 MW of installed wind power paired with a 741 kWh battery. Assuming an …

Geo-Spatial Mapping As A Catalyst For Creative And Engaged Design In Engineering Education, Jessie Zarazaga

Multidisciplinary Studies Theses and Dissertations

Exploiting the technology of geo-spatial mapping student designers can develop deep understandings of the rich and layered data of a spatial context, a situational understanding essential to responsible civic design. However the actions inherent in the construction of spatial data armatures can simultaneously be harnessed as creative strategies, in which mapping processes become the context for generative spatial play. The ambition of this study is to propose efficient pedagogic structures to help prepare civil and environmental student engineers to be not only strong participants, but leaders, in the design of the built environment. The interpretation of site data, mapped as …

Wavelet Transform On Digital Rainbow Hologram Based On Spectral Compression For Quality Enhancement In 3d Display Media, Ucuk Darusalam, Panca Dewi Pamungkasari

Makara Journal of Technology

A digital rainbow hologram (DRH) is a potential next-generation three-dimensional display media for the development of modern and smart electronics devices. It is one of the methods that can support the characteristic whereby a realistic display media occupies the space that the real object would have occupied. Since a rainbow hologram records a large amount of spatial or temporal frequency component from the object that represents the rainbow spectrum, a large amount of information needs to be decoded digitally. In this paper, to reconstruct a DRH, we propose a novel method based on the modulation of red, green, and blue …

The Timber Buckling Restrained Brace Frame, Jessica Resta

Architectural Engineering

With the increasing awareness on the topic of earthquake resistance, efficient, cost-effective, and environmentally friendly solutions in the structural field are on the rise. The purpose of this report is to investigate the Timber Buckling Restrained Brace (TBRB), a new lateral-resisting element made of steel and lumber, applicable in residential and small commercial units. In addition to the TBRBs’ materials being readily available, the braces are easy to manufacture, reducing overall costs of production and transportation. The brace, made partly of wood, has also a low environmental impact when compared to other lateral force resisting elements like concrete shearwalls or …

Global Opportunities To Increase Agricultural Independence Through Phosphorus Recycling, Stephen M. Powers, R. B. Chowdhury, G. K. Macdonald, A, H.W. Beusen, A. F. Bouwman, S. E. Hampton, Brooke K. Mayer, M. L. Mccracklin, D. A. Vaccari

Civil and Environmental Engineering Faculty Research and Publications

Food production hinges largely upon access to phosphorus (P) fertilizer. Most fertilizer P used in the global agricultural system comes from mining of nonrenewable phosphate rock deposits located within few countries. However, P contained in livestock manure or urban wastes represents a recyclable source of P. To inform development of P recycling technologies and policies, we examined subnational, national, and global spatial patterns for two intersections of land use affording high P recycling potential: (a) manure‐rich cultivated areas and (b) populous cultivated areas. In turn, we examined overlap between P recycling potential and nation‐level P fertilizer import dependency. Populous cultivated …

Comment On “Patented Blunderings, Efficiency Awareness, And Self-Sustainability Claims In The Pyrolysis Energy From Waste Sector”, Patrick J. Mcnamara, Daniel Zitomer, Zhongzhe Liu

Civil and Environmental Engineering Faculty Research and Publications

No abstract provided.

Initial Development Of Advanced, High-Rate Treatment Process For Wet Weather Flows, Paige Elyse Peters

Master's Theses (2009 -)

Billions of gallons of untreated water are discharged into lakes and rivers every year due to combined and sanitary sewer overflows during high-intensity precipitation events. Combined sewer overflows (CSOs) and sanitary sewer overflows (SSOs) pose both environmental and public health risks due to potential human contact with contaminated water. To address the overflow issue, a novel, advanced, high-rate wet weather treatment process was investigated. The high-rate treatment process combined chemically enhanced primary treatment (CEPT) with an advanced oxidation process (AOP) using ozone to rapidly remove total suspended solids (TSS) and chemical oxygen demand (COD), inactive E. coli, and oxidize the …

Improved Reliability Of Stormwater Detention Basin Performance Through Water Quality Data-Informed Real-Time Control, Sazzad Sharior

Master's Theses (2009 -)

The objective of stormwater detention basins is to capture stormwater runoff to reduce and delay peak flow and to improve the water quality. These objectives can be improved upon by actively controlling the outflow of the basins rather than traditional passive outflow structures. There are studies demonstrating the performance of the active controls that respond in real-time to basin hydraulics, detention time, and rainfall forecasts. We hypothesize that the performance of these active controls can be improved upon by incorporating real-time water quality data streams into the control algorithm. Furthermore, we hypothesize that performance of these active controls also depends …

Impact Of Electrocoagulation Pretreatment On E. Coli Mitigation Using Electrooxidation, William Mcgregor Lynn

Master's Theses (2009 -)

Small drinking water systems serve approximately 20% of the US population, but they can struggle to comply with the Total Coliform Rule and the Disinfectant and Disinfection Byproduct Rule. Issues with insufficient funds to effectively treat the water and difficulties with the transportation of required chemicals can affect compliance. Electrochemical processes may offer an alternative approach for small water systems as they have demonstrated some advantages over traditional treatments, such as reduced handling and storage of chemicals and cost effectiveness. Sequential electrochemical processes have yet to be tested for the treatment of E. coli in drinking waters. In this study, …

Near Real-Time Flood Forecasts From Global Hydrologic Forecasting Models, Corey Nicholas Krewson

Theses and Dissertations

This research assesses possible methods for extending the Streamflow Prediction Tool from a streamflow forecasting model to a flood extent forecasting model. This new flood extent forecasting model would allow valuable and easy to understand information be disseminated in a timely manner for flood preparation and flood response. The Height Above Nearest Drainage (HAND) method and AutoRoute method were considered for flood extent models but the HAND was the better option for its simple and quick computation as well as its viability on a global scale. Due to the importance of Digital Elevation Models (DEMs) in these flood extent models, …

Hydration Of Binary Portland Cement Blends Containing Silica Fume: A Decoupling Method To Estimate Degrees Of Hydration And Pozzolanic Reaction, Wenyu Liao, Xiao Sun, Aditya Kumar, Hongfang Sun, Hongyan Ma

Materials Science and Engineering Faculty Research & Creative Works

Determination of degrees of hydration/reaction of components of blended cementitious systems (i. e., cement and SCMs: supplementary cementitious materials) is essential to estimate the systems' properties. Although the best methods for determining degrees of reaction of different SCMs have been recommended by RILEM TC238, they rely on either expensive equipment (e.g., nuclear magnetic resonance) or time-consuming sample preparation and data processing (e.g., backscattered electron image analysis). Furthermore, these methods cannot simultaneously characterize degree of hydration of cement and degree of reaction of SCMs. A novel decoupling method, which can simultaneously estimate the degree of hydration of cement and the degree …

Wheat Strip Effects On Microbial Transport Following Variable Applications Of Beef Cattle Manure, Lisa M. Durso, John E. Gilley, David B. Marx, Chance A. Thayer, Bryan L. Woodbury

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Vegetative filter strips (VFS) consisting of perennial vegetation have been successfully used to reduce the transport of contaminants in runoff from land application areas. The effectiveness of a winter wheat strip, which may be more acceptable to producers, in reducing microbial transport was examined in this study. A 1.4 m wheat strip was used to allow direct comparison with experimental results obtained in previous studies. Beef cattle manure was applied to 0.75 m wide by 4.0 m long plots established on an Aksarben silty clay loam located in southeast Nebraska. Manure was added at rates required to meet the 0- …

Molecularly Conductive Behavior Of Blended Polymer Electrolyte-Based Cmc/Pva, Noor Saadiah Mohd Ali, Dishen Zhang, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

This study investigated the electrical conduction and structural behavior of blended polymer electrolyte (BPE)-based carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) in the development of solid-state electrochemical devices. Based on impedance spectroscopy and correlating Fourier transform infrared (FTIR) with thermogravimetric analysis, a framework was proposed to explain the structural enhancement of the BPE system. As revealed by FTIR, the optimum conductivity of CMC/PVA BPEs was 9.21 × 10−6 Scm−1 for 80:20 composition attributed to the intermolecular attraction between the polymers. Thermal stability of the CMC/PVA was influenced by the formation of a hydrogen bond between the hydroxyl (-OH), carboxylate (-COO-), …

Multistage Sonication Effect On The Composition And Properties Of Degraded Chitosan Product, Nurul Laili Arifin, Emma Savitri, Anjar Indah, Fesa Putra, Sumarno Sumarno

Makara Journal of Technology

The sonication method randomly breaks polymer chains to produce a varied distribution of products. A scheme with multi-stage sonication steps is proposed to identify oligomers and low molecular weight chitosan based on changes to the degrad-ed product. For each sonication level, 1% (w/v) chitosan in 1% (v/v) aqueous acetic acid was sonicated for 120 min at 60 °C. The products of the sonication treatment were deprotonized by adding an alkali solution, freeze dried and insoluble product re-sonicated until a low molecular weight was produced. Low molecular weight chitosan/insoluble products were character-ized with Fourier-transform infrared spectra (FT-IR) and X-ray diffraction (XRD) …

Data Fusion Method Based On Adaptive Kalman Filtering, Bernadus Herdi Sirenden

Makara Journal of Technology

This paper discusses data fusion methods to combine the data from a rotary encoder and ultrasonic sensor. Both sensors are used in a micro-flow calibration system developed by the Research Center of Metrology LIPI. The methods studied are hierarchical data fusion and Kalman filtering. Three types of Kalman filters (KFs) are compared: the conventional Kalman filter and two adaptive Kalman filters. Moreover, a method to combine the uncertainty results from KF in hierarchical data fusion is proposed. The aim of this study is to find appropriate methods of data fusion that can be implemented in micro-flow calibration systems. Data from …

Study Of Zno Nanospheres Fabricated Via Thermal Evaporation For Solar Cell Application, Fatin Farisha Alia Azmi, Bouchta Sahraoui, Saifful Kamaluddin Muzakir

Makara Journal of Technology

A solar cell is a device that absorbs light energy to generate electrical energy. A typical example of a solar cell is the quantum dot solar cell (QDSC), which consists of three main components: (i) fluorophore: the component that absorbs light and generates excited state electrons and holes, (ii) photoelectrode: the component that transports the excited state electron and prevents recombination of excited state electrons and holes, and (iii) electrolyte: the component that re-plenishes the vacancy left by the excited electron in the hole. Despite the increasing number of research in the QDSC field, to date, a device with significant …