Applied Mechanics Commons^™

Solar Array Suspension Mechanism Final Design Report For Atk Space, Alex Gould, Randon Kruse, Jeremy Graul, Patrick Barney

Mechanical Engineering

The purpose of this project is to improve the existing Solar Array Suspension Mechanism used by ATK Space for the manufacturing and testing of deployable solar arrays. The current system requires too much time to operate and has too many removable parts that may fall and damage the solar arrays. Through the design and verification process the team successfully constructed a quick connecting suspension mechanism that requires no tools to use and has no removable parts. The final design includes the existing force gauge and large adjustment bars used by ATK Space with the addition of a compression spring adjustment …

Strider, Eric Johnson, Alex Trask, Ricardo Garcia

Mechanical Engineering

No abstract provided.

Newsletter 41 Issue 1 - Spring 2010 - Nuts And Bolts, Larsen Tractor Museum

Friends of the Larsen Tractor Museum

No abstract provided.

Morphological Evolution Of Single-Crystal Ultrathin Solid Films, Mikhail Khenner

Mathematics Faculty Publications

An introduction to mathematical modeling of ultrathin solid films and the role of such modeling in nanotechnologies: Educational presentation for senior physics majors

Morphological Evolution Of Single-Crystal Ultrathin Solid Films, Mikhail Khenner

Mathematics Faculty Publications

An introduction to mathematical modeling of ultrathin solid films and the role of such modeling in nanotechnologies: Educational/Research presentation for senior physics majors

Nuts And Bolts - Ltm Newsletters, Tractor Museum

Friends of the Larsen Tractor Museum

Newsletters published by the Larsen Tractor Museum in 2010

Where do we grow from here? by Curt McConnell, editor

Chris Ford has big plans for small groups in 2010 by Curt McConnell, editor

News from Exhibits by Luis Vasquez, chair of collections committee

Engine comes together as Co-Op E3 progresses by Curt McConnell

Description of our Sound Level Measuring and Analyzing Equipment by Lou Leviticus

Development of conservation tillage methods by Bill Splinter, museum director

Curator's Report by Lou Leviticus

Associate Report by Jeremy Steele, museum associate

Obituary Note - Robert Kleis

Oscillatory And Monotonic Modes Of Long-Wave Marangoni Convection In A Thin Film, Sergey Shklyaev, Mikhail Khenner, Alexei Alabuzhev

Mathematics Faculty Publications

We study long-wave Marangoni convection in a layer heated from below. Using the scaling k=O Bi, where k is the wave number and Bi is the Biot number, we derive a set of amplitude equations. Analysis of this set shows presence of monotonic and oscillatory modes of instability. Oscillatory mode has not been previously found for such direction of heating. Studies of weakly nonlinear dynamics demonstrate that stable steady and oscillatory patterns can be found near the stability threshold.

Computational Fluid Dynamic Optimization And Design For The Airborne Laser System, Matthew James Opgenorth

Electronic Theses and Dissertations

The Airborne Laser (ABL) was designed to destroy any ballistic missile shortly after launch that could be a threat to the United States and its allies. The ABL uses several lasers to accomplish the destruction of the ballistic missile, most notably the high powered Chemical Oxygen Iodine Laser (COIL). The COIL is a complex device that could be improved upon in several areas that will result in overall weight reduction, refinement of beam quality, and increased magazine capacity.

This dissertation presents novel design and optimization techniques coupled with fluid dynamics to improve the performance of the COIL system. The focus …

Oscillatory And Monotonic Modes Of Long-Wave Marangoni Convection In A Thin Film, Sergey Shklyaev, Mikhail Khenner, Alexei Alabuzhev

Mathematics Faculty Publications

We study long-wave Marangoni convection in a layer heated from below. Using the scaling k=O Bi, where k is the wave number and Bi is the Biot number, we derive a set of amplitude equations. Analysis of this set shows presence of monotonic and oscillatory modes of instability. Oscillatory mode has not been previously found for such direction of heating. Studies of weakly nonlinear dynamics demonstrate that stable steady and oscillatory patterns can be found near the stability threshold.

Newsletter 43 Issue 3 - Fall 2010 - Nuts And Bolts

Friends of the Larsen Tractor Museum

No abstract provided.

Structural Health Monitoring With Piezoelectric Wafer Active Sensors—Predictive Modeling And Simulation, Victor Giurgiutiu

Faculty Publications

This paper starts a review of the state of the art in structural health monitoring with piezoelectric wafer active sensors and follows with highlighting the limitations of the current approaches which are predominantly experimental. Subsequently, the paper examines the needs for developing a predictive modeling methodology that would allow to perform extensive parameter studies to determine the sensing method’s sensitivity to damage and insensitivity to confounding factors such as environmental changes, vibrations, and structural manufacturing variability. The thesis is made that such a predictive methodology should be multi-scale and multi-domain, thus encompassing the modeling of structure, sensors, electronics, and power …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Enhance Diamond Coating Adhesion By Oriented Interlayer Microcracking, Habio Guo, Xingcheng Xiao, Yue Qi, Zhi-Hui Xu, Xiaodong Li

Faculty Publications

In this paper, we report a microcrack toughening mechanism for enhancing the adhesion of diamondcoating. The oriented microcracks were formed within the TiC interlayer to dissipate strain energy and accommodate deformation via the crack opening-closing mechanism, thus enhancing the coating/substrate interfacial toughness. The delamination of diamondcoating was effectively prevented when the parallel microcracks were confined within the interlayer and arrested at interfaces of coating/interlayer/substrate. Density functional theory calculations revealed that the highly anisotropicfracture strength of the TiC phase energetically favors crack initiation and propagation along (100) planes only, which are 54.7° away from the interface. These microcracks are constrained inside …

Thermocapillary Effects In Driven Dewetting And Self-Assembly Of Pulsed Laser-Irradiated Metallic Films, Mikhail Khenner

Mathematics Faculty Publications

A mathematical model for the evolution of pulsed laser-irradiated, molten metallic films has been developed using the lubrication theory. The heat transfer problem that incorporates the absorbed heat from a single laser beam or the interfering laser beams is solved analytically. Using this temperature field, we derive the 3D long-wave evolution PDE for the film height. To get insights into dynamics of dewetting, we study the 2D version of the evolution equation by means of a linear stability analysis and by numerical simulations. The stabilizing and destabilizing effects of various system parameters, such as the reflectivity, the peak laser beam …

Thermocapillary Effects In Driven Dewetting And Self-Assembly Of Pulsed Laser-Irradiated Metallic Films, Mikhail Khenner

Mathematics Faculty Publications

A mathematical model for the evolution of pulsed laser-irradiated, molten metallic films has been developed using the lubrication theory. The heat transfer problem that incorporates the absorbed heat from a single laser beam or the interfering laser beams is solved analytically. Using this temperature field, we derive the 3D long-wave evolution PDE for the film height. To get insights into dynamics of dewetting, we study the 2D version of the evolution equation by means of a linear stability analysis and by numerical simulations. The stabilizing and destabilizing effects of various system parameters, such as the reflectivity, the peak laser beam …

Thermocapillary Effects In Driven Dewetting And Self-Assembly Of Pulsed Laser-Irradiated Metallic Films, Mikhail Khenner

Mathematics Faculty Publications

A mathematical model for the evolution of pulsed laser-irradiated, molten metallic films has been developed using the lubrication theory. The heat transfer problem that incorporates the absorbed heat from a single laser beam or the interfering laser beams is solved analytically. Using this temperature field, we derive the 3D long-wave evolution PDE for the film height. To get insights into dynamics of dewetting, we study the 2D version of the evolution equation by means of a linear stability analysis and by numerical simulations. The stabilizing and destabilizing effects of various system parameters, such as the reflectivity, the peak laser beam …

Formula Sae Interchangeable Independent Rear Suspension Design, Mike Mccune, Daniel Nunes, Mike Patton, Courtney Richardson, Evan Sparer

Mechanical Engineering

The Suspension Solutions design team has completely designed built and tested an independent rear suspension system for the 2008 FSAE car. The car currently features a solid rear axle, and the task of converting it to incorporate an interchangeable rear suspension has been undertaken in order to quantify the advantages and disadvantages of each design philosophy. The car has been properly tested with both the solid axle and independent rear suspension side-by-side, however more testing is suggested. After pushing both setups to their limits on a 50ft diameter skid pad, the test results were quantified, and a final comparison between …

Supermileage Team - Urban Concept Competition Vehicle Chassis Design Report, Andrew Allport, Kevin Braico, Kevin Charles, George Kyi, William Lai

Mechanical Engineering

This research and design project was proposed by the Cal Poly Supermileage team. They have requested for our team to design an Urban Concept car, a new category of vehicles to compete for fuel efficiency in the Shell Eco-marathon in 2010. The primary focus of our team is in the design and construction of a chassis the Supermileage team can use for the 2010 competition in Fontana, CA. This design must meet dimensional and functional requirements set by Shell while being designed to maximize efficiency in the competition.

There were various chassis concepts under consideration that would possibly work for …

Hydraulic Hand Press Final Project Report, Nathaniel Marc Brown, Matthew Thomas Knorr

Mechanical Engineering

This report provides a thorough description of the design of a hydraulic hand-operated press by mechanical engineering students at California Polytechnic State University, San Luis Obispo, California, for the Estrella Warbirds Museum in Paso Robles, California. It begins with research into hydraulic operations, a brief study of fluid power and incompressible fluids, and a look into existing products. Specified customer requirements stipulate the loading and general size constraints. As part of the project, a schedule is laid out following industry techniques. Brainstorming and decision matrices are utilized as well, conveying our design process. A basic structure is developed using strength …

Best-In-Class Global Bumper Reinforcement Beam, Garret Anthony Bautista, Chad Anthony Hardin, Benjamin Ray Taylor

Mechanical Engineering

Modern bumper systems are governed by laws and regulations imposed separately by various countries. Today, the regulations in China, North America, and Europe are becoming more similar, but there is not a widely accepted bumper reinforcement that meets the requirements of all markets around the globe.

A universal bumper reinforcement beam incorporating Plug-n-Play techniques was developed to meet and exceed all testing requirements and performance standards of each country. These Plug-n-Play techniques consist of adding energy absorbing attachments to the front of a base bumper beam. Simple beam analysis and FEA were the primary analysis tools in the development of …

October 2009, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

Agenda, minutes, treasurer report, director report, docent report, associate report, activities report, test lab report

Strain Energy And Lateral Friction Force Distributions Of Carbon Nanotubes Manipulated Into Shapes By Atomic Force Microscopy, Mark C. Strus, Roya R. Lahiji, Pablo Ares, Vincente Lopez, Arvind Raman, Ron R. Reifenberger

Other Nanotechnology Publications

The interplay between local mechanical strain energy and lateral frictional forces determines the shape of carbon nanotubes on substrates. In turn, because of its nanometer-size diameter, the shape of a carbon nanotube strongly influences its local electronic, chemical, and mechanical properties. Few, if any, methods exist for resolving the strain energy and static frictional forces along the length of a deformed nanotube supported on a substrate. We present a method using nonlinear elastic rod theory in which we compute the flexural strain energy and static frictional forces along the length of single walled carbon nanotubes (SWCNTs) manipulated into various shapes …

Crack Identification By Multifractal Analysis Of A Dynamic Rotor Response, Grzegorz Litak, Jerzy T. Sawicki

Mechanical Engineering Faculty Publications

Multifractal analysis has been used to diagnose cracked and healthy rotors. Is has been shown that the complexity and regularity criteria of the dynamical systems defined by the multiple scaling of the time series can indicate the damages of the rotating shaft. Relation to the standard power spectrum technique has been also discussed.

Design And Development Of Rapid Battery Exchange Systems For Electric Vehicles To Be Used As Efficient Student Transportation, Jonathan A. Bevier

Master's Theses

Rapid battery exchange systems were built for an electric van and pedal assist electric bike as a method of eliminating the need to recharge the vehicles batteries in order to increase the feasibility of using electric propulsion as a method of efficient student transportation. After selecting proper materials it was found that the systems would need a protective coating to ensure consistent operation. 1020 cold rolled steel samples coated with multiple thicknesses of vinyl resin paint, epoxy resin paint, and powder coating were subjected to environmental wear tests in order to determine if the type and thickness of common protective …

Carbon Fiber Leaf Springs For Adaptive Cross Country Skiing, William Drew Atkinson

Master's Theses

This work describes the development of a custom sit ski for US Ski Team paralympian Greg Mallory from concept through prototype fabrication. The ski consists of a custom seat molded specifically for the athlete, carbon fiber leaf springs, and a custom binding attachment system compatible with NNN style cross country bindings. The sit ski is designed to maximize poling power through the use of an upright rather than reclined seating position, allowing for increased utilization of core muscle strength. The springs were designed based on information gathered by a custom National Instruments data acquisition system, and stiffness analysis was conducted …

Mechanical Simulation Of Articular Cartilage Based On Experimental Results, Kevin Matthew Stewart

Master's Theses

Recently, a constituent based cartilage growth finite element model (CGFEM) was developed in order to predict articular cartilage (AC) biomechanical properties before and after growth. Previous research has noted limitations in the CGFEM such as model convergence with growth periods greater than 12 days. The main aims of this work were to address these limitations through (1) implementation of an exact material Jacobian matrix definition using the Jaumann-Kirchhoff (J-K) method and (2) quantification of elastic material parameters based upon research findings of the Cal Poly Cartilage Biomechanics Group (CPGBG). The J-K method was successfully implemented into the CGFEM and exceeded …

Tobacco Mosaic Virus Templated Synthesis Of One Dimensional Inorganic-Polymer Hybrid Fibres, Jianhua Rong, Fiona Oberbeck, Xinnan Wang, Xiaodong Li, Jerry Oxsher, Zhongwei Niu, Qian Wang

Faculty Publications

Inorganic–polymer hybrid nanofibres were prepared by using a rod-like tobacco mosaic virus (TMV) as a template. With tetraethylorthosilicate (TEOS) as a precursor, long silica-coated TMVfibres were formed via a head-to-tail assembly, which showed a substantial increase of the elastic modulus. Furthermore, homogenous titania–TMV hybrid fibres could be prepared using polyaniline-coated TMV fibres as a template, which were used to form a composite film that was able to sense liquefied petroleum gases.

Optimization And Stress Analysis Of A Single Stage Rotary Compressor Shaft, Arjunkumar Tummuri

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science & Technology at Morehead State University in partial fulfillment of the requirements for the Degree of Master of Science by Arjunkumar Tummuri May 5, 2009.

College Of Engineering Senior Design Competition Spring 2009, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

An On-Sun Parametric Study Of Solar Hydrogen Production Using Wo3 Photoanodes, Christopher K. Halford

UNLV Theses, Dissertations, Professional Papers, and Capstones

The solar production of hydrogen using photoactive electrodes is a topic receiving much attention in recent years. The use of thin metal oxide films as photoanodes allows the water splitting reaction to occur at a much lower applied voltage than would be necessary with a straight electrolysis process. Researchers have reported up to 18% solar to hydrogen efficiencies over short periods. The University of Nevada Las Vegas in conjunction with the UK based firm Hydrogen Solar have developed a prototype of this type of cell using a WO3 photoanode. An on-sun test facility has been constructed by the UNLV Center …