Geotechnical Engineering Commons^™

Feasibility Of Additive Manufactured Materials For Use In Geotechnical Laboratory Testing Applications, Matthew P. Watters

Graduate Theses and Dissertations

The factors affecting the positive volumetric strain, or dilatancy, typically observed in response to shearing of a dense granular material have long been investigated; however, there still lacks a direct relationship between particle shapes and the resulting dilatant response. The typical Mohr-Coulomb strength parameter associated with granular material is known as the effective friction angle (φ’). For a dense granular assemblage, the peak friction angle has been described as being comprised of a dilatant friction angle (φ’d) component and a critical state friction angle (φ’cv) component. While the topic of dilatancy and factors (both inherent and extrinsic) affecting its behavior …

Development Of A Multiband Remote Sensing System For Determination Of Unsaturated Soil Properties, Cyrus D. Garner

Graduate Theses and Dissertations

A multiband system including active microwave sensing and visible-near infrared reflectance spectroscopy was developed to measure unsaturated soil properties in both field and laboratory environments. Remote measurements of soil volumetric water content (θv), soil water matric potential (ψ), and soil index properties (liquid limit [LL], plastic limit [PL], and clay fraction [CF]) were conducted. Field-based measurement of θv was conducted using a ground-based radar system and field measurements within 10 percentage points of measurements acquired with traditional sampling techniques were obtained. Laboratory-based, visible and near infrared spectroscopy was found to be capable of obtaining empirical, soil specific regression functions (partial …

Effectiveness Of Small Strain Shear Wave Velocity As A Property For Assessing Damage Associated With Alkali-Silica Reaction In Concrete, Dillon K. Self

Civil Engineering Undergraduate Honors Theses

This research paper details the monitoring of expansion and shear wave velocity for fifteen concrete prisms cast in accordance with ASTM C1293 utilizing five mix designs with varying levels of ASR reactivity. Jobe sand and sodium hydroxide pellets were added in various quantities to increase the reactivity of the prisms. Strain measurements of the prisms were taken according to ASTM C129 and the shear wave velocity of the prisms was measured using ASTM C215. These measurements were taken weekly, then monthly for over a year. It was determined that shear wave velocity of the prisms decrease linearly as strain in …

A Spreadsheet For Estimating Soil Water Characteristic Curves (Swcc), Ghada Ellithy

Publications

SWCC can be measured in the lab; however, due to the cost, time, and high variability in the results, empirical equations were developed using multiple regression approaches on databases consisting of a large number of measured SWCCs. The spreadsheet presented herein utilizes different methods that use basic soil properties, such as grain size distribution and Atterberg limits, to calculate the input parameters for van Genuchten and Fredlund and Xing equations. These parameters are required by numerical models, such as SEEP/W, to perform transient seepage analysis. The spreadsheet allows copying the generated curve data points as well as an input into …

Re-Evaluation Of Acceptance Testing Criteria For Structural Masonry Using The Prism Test Method, James Bristow

UNLV Theses, Dissertations, Professional Papers, and Capstones

The current acceptance criteria for structural masonry in accordance with International Building Code allows for the prism test method to be used. However, without a proper understanding of the effects of variable material properties such as individual masonry unit compressive strength and the various material moduli of elasticity, as well as the effect of field conditions on the unit’s performance, masonry prisms may “fail” to reach the design compressive strength (f’m).

By identifying causes of failure and evaluating the failure magnitude, it is concluded that when the masonry prism test method is utilized for acceptance testing of as-built masonry structures, …

Smartvid.Io, Purdue Ect Team

ECT Fact Sheets Archive

The collection, organization, and retrieval of industrial media is a pervasive challenge that is especially glaring for companies in the AEC industry. Construction projects often generate large volumes of pictures & videos from the field for tracking progress and communicating between engineers, contractors, and subcontractors. It is not uncommon for field personnel to capture hundreds of photos per week on any given jobsite.

Smartvid.io is a cloud-based software solution designed for the specific needs of industrial media. The application’s internal deep-learning engines, collectively nicknamed VINNIE (for ‘Very Intelligent Neural Network for Insight and Evaluation’), use speech and image recognition to …

Hillman Composite Beam (Hcb®), Purdue Ect Team

ECT Fact Sheets Archive

The Hillman-Composite Beam (HCB®), is an innovative structural member for use in highway and railroad bridges as well as marine facilities. The HCB is essentially a lightweight reinforced concrete beam strengthened and protected by a corrosion-resistant and resilient Fiberglass Reinforced Polymer (FRP) shell.

The beam is comprised of three main components, a concrete arch (compression reinforcement), an FRP bottom flange encapsulating steel strands tying the ends of the arch together (tension reinforcement) and the FRP shell. Galvanized Rebar “shear connectors” are used to make the beam composite with the concrete deck in the same manner as pre-stressed concrete beams.

The …

Industrial-Grade Monitoring Solution: Hoistcam, Purdue Ect Team

ECT Fact Sheets Archive

Safety and productivity are top priorities for contractors and industrial operations. Improving either makes a company more profitable and competitive. Technology advancements that can do both are important for every company to consider. HoistCam^TM industrial-grade video monitoring solutions can improve employees’ productivity and workplace safety in the construction industries. HoistCam also improves efficiency of operations and reduces job site accidents resulting in substantial cost savings to a contractor.

HoistCam™ is an integrated, wireless video system. The use of HoistCam eliminates blind lifts, blind spots and can share the live video with anyone, anywhere with solid security and easy control. …

Numerical And Experimental Studies On Coastal Marsh Erosion Under Hurricane Induced Wave And Current, Minhaz M. Shahriar

Doctoral Dissertations

Considering the past history and future risks of hurricanes in the USA, well understood storm protection plans are needed to shelter the important areas of the population and economy, especially within southeastern Louisiana. It is extensively assumed that marshes offer protection from hurricane though the degree of this protection is not well measured or understood due to the complex physics involved in this overall system. Moreover, marshes experience significant erosion while serving as a barrier for important areas. Consequently, a particular method to quantify the effects on marshes during a coastal hurricane period is necessary to mitigate major marsh loss. …

Recommended Selective Maintenance And Rehabilitation Treatment Approach For Air Force Primary Rigid Runway Pavement Systems, Christopher M. Twigg

Theses and Dissertations

The Air Force is facing the challenge to preserve the current inventory of 154 million square yards of paved airfield assets while at the same time reducing the budget by $36.2 billion between fiscal years 2015-2019. This research sought to determine a selective maintenance and rehabilitation treatment approach that allocates resources efficiently to preserve the degrading pavement assets in the financially constrained environment. Air Force pavement inspection reports from the past five years provided 4289 observed pavement distress data points for this research. The data was inputted into the pavement management software, PAVER, to calculate the Pavement Condition Index (PCI) …

Purdue Ect Report - Fourth Quarter 2016, Purdue Ect Team

ECT Fact Sheets Archive

Fourth Quarter 2016

This is a quarterly report from the Purdue ECT.

Practical Considerations In Determining Timber Pile Depth Using The Sonic Echo Method, Ali F. Jwary

Civil Engineering ETDs

The Federal Highway Administration indicates that about 85,000 bridges in the United States have no original contract documents with information about the type, depth, geometry and material of their foundations (FHWA, 2010). Furthermore, the National Bridge Inventory (NBI) provides information about 86,133 bridges nationwide that are rated as scour critical because of unknown foundation condition. In New Mexico, there are more than 281 bridges with unknown foundations, which are owned by the New Mexico Department of Transportation; 71 of these are timber bridges. These data indicate a serious problem that needs decisive action to assess the unknown bridge foundation characteristics …

Bicp Global Bim Study - Lessons For Ireland’S Bim Programme, Barry Mcauley, Alan Hore, Roger West

Reports

The Construction IT Alliance (CitA) has been promoting the benefits of digitisation in the construction and engineering industry in Ireland since its formation back in 2002. Whilst the Alliance has always strived to ensure that its members are exposed to a wide spectrum of contemporary digital tools and processes, the concept of Building Information Modelling (BIM) has dominated the focus of its activities over the past five years.

BIM can be described as a digital tool that facilitates everybody to better understand a building or structure through the use of a digital model which draws on a range of data …

Road Zipper™, Purdue Ect Team

ECT Fact Sheets Archive

Construction work zones are growing in number around the world. The natural aging of existing roadway infrastructure ensures that more and more maintenance and rehabilitation will be required. Work zones, by their very definition, create two major problems that must be addressed in some way: safety and mobility. In the United States, highway work zones are responsible for almost 25% of all non-recurring congestion and 10% of overall congestion. Vehicle accidents are more common in work zones, and traffic congestion through work zones on urban arterials and freeways is often considered to be “unavoidable." To address these issues, ROAD ZIPPER™ …

Influence Of Moisture Content Distribution In Soil On Pavement And Geothermal Energy, Md Adnan Khan

Doctoral Dissertations

Moisture content in soil has a great implication in engineering design, and it has been heavily investigated by soil engineers and scientists. If moisture content in expansive soil changes drastically, it will create significant volume change in the soil. If expansive soil is present in building foundation or pavement subgrade, it may result in structural failure. On the other hand, if sufficient moisture content is present in soil, it will increase the production of geothermal energy from the ground soil. This dissertation is an effort to understand the effects of moisture content on both expansive soils and geothermal energy that …

Lakebed Characterization Using Side-Scan Data For Investigating The Latest Lake Superior Coastal Environment Conditions, Hasan Salih Kulunk

Dissertations, Master's Theses and Master's Reports

This thesis provides a review of the development of hydrographic survey equipment and supporting geospatial equipment and technology such as GPS. Using SonarWiz, a sonar image processing software package, lakebed classification methodologies were evaluated for mapping Buffalo Reef in Lake Superior located near Gay, Michigan. The goal was to develop an approach to mapping the reef bed and delineating various components of the lake bottom, including stamp sands, which are migrating from the abandoned Gay copper processing stamp mill to the reef. This contamination of the reef is having an adverse effect on habitats important to local flora and fauna. …

Site Specific Sinkhole Risk Assessment In Central Florida Using Cone Penetrometer Testing, Ryan Shamet

Electronic Theses and Dissertations

As Florida's population is expanding and greater fluctuations in groundwater levels are being recorded, Central Florida has been experiencing a higher frequency of sinkhole occurrences than ever before in recorded history. Sinkholes in Central Florida are formed by a combination of bedrock weathering and overburden soil erosion due to the groundwater recharge and are a part of Florida's past and future geology. The initial stage of a sinkhole is referred to as soil raveling and is the most effective time to perform soil improvement measures, such as grouting, to mitigate further expansion of a subterranean void. Subsurface exploration tests, commonly …

Resistivity Profiles Of Perth Soil In Australia In Leak-Detection Test, Lopa M. Pandey, Sanjay K. Shukla, Daryoush Habibi

Research outputs 2014 to 2021

The use of a suitable leak-detection system for the prevention and mitigation of pollution due to lining system failures is integral to the proper management of landfill facilities. This paper briefly summarises various methods of leak detection that are currently being practised. The details of a newly developed leak-detection technique are also presented. The tests were conducted to evaluate the performance of the new technique by use of controlled leakage. The resulting resistivity profiles for Perth soil in Australia were obtained at 10 min. This method is found to be effective in detecting and locating liner leakage issues within 30 …

Assessment Of Rockfall Rollout Risk Along Varying Slope Geometries Using The Rocfall And Crsp Software, Mariam S. Al E'Bayat

Masters Theses

"Most routes in mountainous areas suffer from rock falling, rolling and bouncing risk. There are many computer programs concerned with simulating the rockfall problem, and whereas they have the same purpose, they however differ in the input data that's needed to simulate the problem, and they also differ in the way of processing and kind of output.

This study used Rocfall® and the Colorado Rockfall Simulation Program (CRSP®) to simulate sixty-three models of varying slope geometry, where only the slope geometry is changed with the same material properties for both the slope and the rocks.

Both programs were fast and …

Imaging In Karst Terrain Using The Electrical Resistivity And Multichannel Analyses Of Surface Wave Methods, Ragab W. Jaafar

Masters Theses

"Electrical resistivity tomography and multi-channel analyses of surface waves data were acquired at a study area in Phelps County in the south-central part of Missouri. The objectives of the investigation were fourfold: 1) to image the subsurface in the study area to a depth of 70 feet; 2) to compare the ERT images generated using both the dipole-dipole and Wenner-Schlumberger arrays; and 3) to assess how variations in the MASW array configuration affected MASW data quality; and 4) to compare the ERT-estimated depth to top-of-rock and the MASW-generated depth to top-of-rock.

The subsurface in the study area was imaged to …

Air Injection As A Scour Countermeasure At Bridge Piers, Ravi Teja Reddy Tippireddy

Dissertations, Master's Theses and Master's Reports

Local scour is a major cause of concern for the stability of bridge piers and the safety of the public using the bridges. Structural countermeasures and flow-altering devices have been developed to deal with local scour. Many armoring structural countermeasures are very effective and efficient in clear water conditions but are susceptible to moving bed forms and leaching. The flow-altering devices are effective in both clear water conditions and moving bed forms, but are prone to clogging, less efficient in changing flow direction, etc. This study aims to reduce the local scour by injecting air in order to reduce the …

Evaluation Of Mechanical Parameters Of Contaminated Road Base And Railway Ballast, Prajwol Tamrakar

Open Access Theses & Dissertations

This Dissertation comprises two topics in the area of transportation geotechnics that focus on the evaluation of stiffness parameters of contaminated road base and railway ballast. The abstracts of these two studies are provided in the following two paragraphs.

The performance of a flexible pavement depends on the mechanical characteristics of its unbound granular base layer. The mechanical characteristics such as stiffness and deformation resistance depend on many factors such as the material gradation, fines content, moisture content, physical properties of coarse aggregate and more. The base materials are often contaminated by the excessive fines that is caused by improper …

Strength Property Variability In Microbial Induced Calcite Precipitation Soils, Jacob Fuller

UNF Graduate Theses and Dissertations

Microbial Induced Calcite Precipitation (MICP) is an attractive alternative for a variety geotechnical ground improvement practices commonly used today and has a variety of potential applications. This research focuses primarily on its use as a soil stabilization technique using the bacteria Sporosarcina Pasteurii and a single injection point percolation method adapted from previous research in granular soils. This method, and most published data, show an inherent variability in both physical and engineering properties due to the distribution of precipitated calcite within the specimen. The focus of this research is on the quantification of the variability in shear strength parameters induced …

In-Situ Assessment Of Concrete Bridge Decks And Pavements Using Stress-Wave Based Methods, Mengxing Li

Doctoral Dissertations

"Concrete infrastructure of United States is aging and deteriorating. Accurate assessment the condition of concrete infrastructure is critical for its maintenance and rehabilitation. Stress-wave based methods, including ultrasonic surface wave (USW) and impact echo (IE), are becoming popular for characterizing defects and mechanical properties of concrete infrastructures. In this dissertation, a comprehensive literature review of seismic wave theory and common types of defects identified in concrete infrastructures, as well as stress-wave based methods used for concrete infrastructure monitoring and characterizing on a selected concrete bridge deck and two concrete pavement segments are present. The utility and reliability of both methods …

Input Parameters In Discrete Element Modeling, Seyedali Yousefi

Civil Engineering ETDs

The discrete element method (DEM) is employed to study complex behaviors of particulate media. Input parameters may greatly affect the response of DEM models and should therefore be selected carefully. Scaling techniques are employed to enlarge prohibitively small time-steps. To study these techniques, dimensionless input parameters were defined. Responses of models in the dimensionless scale were invariant with choice of density, elastic modulus, and characteristic length if the dimensionless parameters were kept constant. Hence, density scaling is equivalent to use of a higher strain-rate, and stiffness scaling results in a higher strain-rate and an elevated stress state in the dimensionless …

Lucidpipe™ Power System, Purdue Ect Team

ECT Fact Sheets Archive

In most gravity fed water transmission pipelines, it is desired to reduce excess pressure head to prevent undue strain on a pipeline and lower the incidence of leaks. Normally this is done with pressure reducing valves that essentially burn off this excess pressure as heat. The LucidPipe™ system converts it to low cost electricity thereby removing unwanted pressure and generating energy at the same time - energy that can be put used behind the grid or put back on the grid. The LucidPipe™ system extracts a small percentage of pressure head providing nearly invisible operation allowing water operators to fulfill …

Soil Moduli Obtained From A Back Pressure Constant Rate Of Strain Bender Element Consolidation Apparatus, Yi Zhao

Graduate Theses and Dissertations

A back-pressure saturated, constant-rate-of-strain consolidation device was modified to incorporate bender elements (BP-CRS-BE) and thus allowed for shear wave measurements during consolidation tests. This newly fabricated system has many advantages over other previous or current devices: 1) it can be utilized not only for laboratory prepared soil samples but also for field sampled soils such as Shelby tube samples, and 2) continuous compression curves, and continuous values of vertical hydraulic conductivity and coefficient of consolidation can be acquired with a significant reduction in testing time. Soil modulus values such as shear modulus and constrained modulus are also able to be …

Geotechnical Properties Of The Travis Peak (Hosston) Formation In East Texas: A Compressive And Tensile Strength Analysis Using Regression Analysis., Pawan Kakarla

Electronic Theses and Dissertations

The estimation of rock mass strength is a key parameter in geotechnical engineering which is used in the design of geotechnical structures like tunnels, dams and slopes. Geotechnical engineering is the branch of civil engineering which works on the principles of soil and rock mechanics to evaluate subsurface conditions, stability of slopes, foundations of structures and construction of earthworks. The main focus of this study was to calculate the strength of Lower Cretaceous Travis Peak Formation rocks of East Texas and to check the accuracy by comparing it with Regression analysis. The parameters which were used were the Uniaxial Compression …

Characterization And Delineation Of Karst Geohazards Along Rm652 Using Electrical Resistivity Tomography, Culberson County, Texas, Adam F. Majzoub

Electronic Theses and Dissertations

The Delaware Basin of West Texas and southeastern New Mexico is the major western subdivision of the Permian Basin and a northern extension of the Chihuahuan Desert. The major evaporite unit within the Delaware Basin is the Castile Formation, which consists of gypsum/anhydrite and is highly susceptible to dissolution and karsting. Manifestations of karst within the Castile outcrop are abundant and include sinkholes, subsidence features and caves, both epigene and hypogene in origin.

Land reconnaissance surveys conducted during the summer of 2015 documented abundant karst landforms in close proximity to a major thoroughfare, RM 652, in Culberson County, Texas. 2D …

Effect Of Temperature On Deep Lined Circular Tunnels In Isotropic And Transversely Anisotropic Elastic Ground, Fei Tao

Open Access Theses

A tunnel is a passageway constructed through soil or rock. It is one of the most important underground structures and has been widely used in transportation. Much research has been done on tunnel performance and on the interaction between ground, excavation, liner installation and support. The work has provided a better understanding of the interplay that exists between deformations and stresses transferred from the ground to the support. Significant insight into the problem has been provided by closed-form analytical solutions. A number of analytical formulations have been obtained for underground openings and lined tunnels under different scenarios, namely shallow or …